$hitty Paint Job - Upgrading, Modifying and Unlocking

SO,
I could take the peeling paint no longer, so I "fixed" it. Or at least I thought I had.
I took apart the unit, very timidly; everything came off but the buttons and what not. I used an old drywall (worn down) sponge, and kept it wet, sanding carefully. Cleaned often as I went, and wasn't too worried about surface scratches, as I was about to paint it.
BTW, the gold finish under that non slip coating is actually quite imressive.
Anyway, only the most advanced techniques, tools, and paint were used. See for yourself...
and yes, that is a roll of toilet paper!!! :lol:
Two days later, the rubber started to peel off. I used "Plasti-Dip" spray paint. I thought a rubber grip might be nice, since I work construction, and black is just plain cool. I tested the tool grip paint on a nokia 3595 dummy, and now I just can't get that **** off of it. I thought it would stick to my wallaby. Apparently, not. I used my fingernail to peel off a wear hole caused by my Al case, and just peeled off the rubber in a few large pieces. Anyway, I'm going to check into good primers soon. I think that the noslip coating that flakes off our units isn't the problem, but the foil finnish that just won't let anything adhere. Anyway, If you have a suggestion or comment, fire away. And sorry, the only digicams i have are a Sony T610 and a V300....
Thanks!

Related

Help fixing a scratch/paint chip

I got a small scratch/paint chip on the black plastic near the usb port does anyone have any ideas on how I can fix this? I was thinking of using black nail polish.
Any other ideas would be appreciated.
Thanks!
Sent from my SAMSUNG-SGH-I897 using XDA App
Couple questions: is it on the rim of the charging port? I got one from removing my charge cable at an angle and it twisted and gouged the plastic on the way out, which leads me to my next question, is it deep? Like is it superficial or is it more like missing the gloss finish and possibly some plastic?
A usful product to have for glossy finishes is Displex, it works amazing on this phone. I am incredibly anal about high gloss finishes and blemishes showing up on them, even if i can only see them in direct sunlight. If you use this product with a cotton swab and gently but firmly rub in a circular pattern the scratches will go away very quickly, if you do it too much or too forcefully you may cause a bit of a clouding effect you can notice in strong light, so just do it for about 30 seconds and wipe it clean with a micro fiber cloth and do a little more, you should need a pea sided drop altogether, this will last for quite a while, just make sure you squeese the tube up and down to kind of mix it if it's been sitting a while. If the blemish is more of a gouge and not a fine scratch then this wont work as well, what it does is polishes the edges of the scratch down and fills in the bottom of the scratch with what's being polished smooth, so it works wonders for small problems, with larger issues you'll end up with a smooth ripple in the plastic as it will wear the hard edges down but obviously won't rebuild what's missing. I was reluctant to use it on my captivate cause it didn't do squat to my htc pure, but it performed remarkably on my captivate, just be methodical about how you use it and when you're done and your scratch is gone to your satisfaction be sure to put a little(and I mean little) on your micro fiber cloth or incredibly soft rag and buff over the area back and forth in one direction, for me that helped eliminate any cloudy effect and polish it back to a brand new phone shine. Just go into Google shopping and search for Displex, it's very inexpensive.
Sorry to repost so quickly but I forgot to mention about the nail polish, you can test it out but if it doesn't work I would be reluctant to use nail polish remover anywhere near the plastic on my captivate as it usually contains acetone which destroys plastic finishes usually, just put a drop on the surface of a cd, if it doesn't bother it you're probably ok, but I would still be reluctant. I'm a painter and have a lot of experience with solvents. The other possible issues with nail polish is it might not grip the phone well and depending on how thick it's applied might actually just pop off when it dries to be really hard. I tried it on my Fuze and it wouldn't cling to it at all; it also left a nasty seam and was just as bad of an eyesore as without it there, acrylic paints are easier to work with and dry very shiny but aren't always that hard, you'd need a type that mixes with a hardener as apposed to generic model paint, model paint takes considerable time to cure and wears down faster than the acrylic plastic of the phone.
Thanks for the advice my friend took a look at it and said its missing the gloss as the black finish came off and now there's a small white circle near the usb port.
I don't know how that happened as I always pocket the phone by itself and nothing else.
Sent from my SAMSUNG-SGH-I897 using XDA App
You may want to still try that polish I mentioned, sometimes with hard plastics like this the nick gives it a powdery look that looks worse than it is, if it's still relatively smooth but is an ugly blemish then it will most likely polish out to a high shine again and the white spot may go away. I don't know the process Samsung used for manufacturing but I was under the impression that they were solid colored plastic possibly with a protective coating over that, if I'm right then that white you mentioned should polish out. Best of luck whatever you decide to do.

Soft rubberized feel back snap on case

I picked up some black Plasti Dip from Lowes. I sprayed it on to my spare purple back cover that came with the phone. It came out awesome. They have other colors also.
Sent from my SGH-T959
Follow me on Twitter @BobMcElroy15
I've been thinking about trying this since no 3rd party seems to want to supply any decent accessories for this phone.
How much did it cost? Pics?
Thanks for the tip.
Its been done already. Search for post
The spray is under 10 bucks. I also sprayed a usb flash drive
Sent from my SGH-T959 using XDA App
Looks sweet. Any prep work involved? Or did u just sprayed it on as is??
Sent from my SGH-T959 using XDA App
I didn't sand it down or anything put you should apply 2-3 coats
I found a can of black (I wish they would have had other colors) at Lowes for $7. 4 coats later, it looks awesome! I love the feel and that it no longer slips out of my hand. No more fatty silicone cases for me. My work colleagues were amazed at how nice this looked and felt.
This was a great tip. Thanks to OP.
dam that looks legit, gonna have to try that!
That looks sweet...
I would like to know how this held up over time..
I am SO glad you posted this! I have been looking at an extended battery on Ebay with a black GLOSSY battery door (BLEH - fingerprint magnet!), but having seen this I'm going to get a can of this stuff and paint the back of that battery door - should be great!
The K-Zoo Kid said:
I would like to know how this held up over time..
Click to expand...
Click to collapse
Unfortunately, no too well so far. It has started to peel back on one side from rubbing when it goes in/out of my pocket. I imagine it's because the original surface is so slick/smooth. I think if it gets bad, I'll try again but spray on some kind of primer or maybe just spray paint first so it has something to hang onto. Anyone have any thoughts/ideas? OP, how is yours holding up?
went to Menards and they didn't carry plasti-dip, so I used this Rustoleum Truck Bed Coating instead... gave the backplate a hard, scratchy black surface. It's kind of awesome. Suddenly my Vibrant felt like a rugged industrial device than a shiny, whimpy product-photo-ready gadget. I cracked up at the difference when I first held it in my hand.
process:
sanded down backplate with sandpaper --> applied and dried two coats --> truckbed.jpg (attached)
superglued dorky metal sticker (it wouldn't take to the rough surface otherwise) --> cleaned up superglue around edges --> applied liquid mask over sticker --> applied coat (and repeated last two steps again) --> texturedetail.jpg (attached)
caldjeff: you need to sand the backplate first w/ sandpaper in order to roughen it up, so that whatever you apply to it has something to grip. This is a general suggestion... I don't know about plasti-dip in particular.
seannyb said:
went to Menards and they didn't carry plasti-dip, so I used this Rustoleum Truck Bed Coating instead... gave the backplate a hard, scratchy black surface. It's kind of awesome. Suddenly my Vibrant felt like a rugged industrial device than a shiny, whimpy product-photo-ready gadget. I cracked up at the difference when I first held it in my hand.
process:
sanded down backplate with sandpaper --> applied and dried two coats --> truckbed.jpg (attached)
superglued dorky metal sticker (it wouldn't take to the rough surface otherwise) --> cleaned up superglue around edges --> applied liquid mask over sticker --> applied coat (and repeated last two steps again) --> texturedetail.jpg (attached)
caldjeff: you need to sand the backplate first w/ sandpaper in order to roughen it up, so that whatever you apply to it has something to grip. This is a general suggestion... I don't know about plasti-dip in particular.
Click to expand...
Click to collapse
Well done! I'm loving this idea and i think im going to try it when i get my extended battery with a backplate.

Naked case (vinyl and/or rubber battery cover) ??

OK - I've been using the ATT store Body Glove case since I bought the Captivate, which is ok but I don't really like the stripes on the back, and it is a bit too slippery for me.
I just ordered the Seidio case because it has more of a matte finish and I liked the felt interior. So I don't know if I like it or not.
A few minutes ago I took the phone out of it's case to dust it and clean out the case when I got a call. I was surprised at how slim the phone felt without it's Body Glove case on. I liked it. But I also found it a bit slippery. ( A speaker phone call was put on the arm of the chair I was in - with the case it would hold - without it slid away)
Now I am wondering if I should just use some skateboard tape or something similar on key areas to allow me to set it down and hold it comfortably (where it won't slip) instead of using a case. I don't use a screen protector and I don't think this phone needs it.
Any comments or suggestions?
Now that I've thought about it for a few minutes - I think what I want is a rubberized battery cover. That would be the bomb.
I don't use a case on mine and I've yet to get a single scratch on the front or back - the glass is very tough. I cringe at having to use a case, losing accuracy, clarity, and brightness on the screen and having to touch through that...having it hard to slip in and out of my pocket...not looking as nice. It's like if your wife made you use a condom every time.
just "paint" it with some Elmer's Rubber Cement. Im really kidding but I'm with you I like the feel of the phone and I hate the rubber case I got it makes it a pain to get in and out of the pocket. Personally I plan on selling this phone in a couple of months so I want it in good condition.
vsboxerboy1 said:
I don't use a case on mine and I've yet to get a single scratch on the front or back - the glass is very tough. I cringe at having to use a case, losing accuracy, clarity, and brightness on the screen and having to touch through that...having it hard to slip in and out of my pocket...not looking as nice. It's like if your wife made you use a condom every time.
Click to expand...
Click to collapse
Agreed that the screen is fine on its own. But I still think the back needs some help.
Also, I do not like condoms. Neither do my wife and kids.
Ah, well I saw something a while back where someone basically took four little rubber/plastic stickers and put one on each corner of the back of the phone to lift the back up off whatever surface you set it on just a hair. I would imagine that you'd get good traction with that too - I can't seem to find the exact application of it though......
This thread is mostly me think out loud.
I believe that what I want is a rubberized battery cover.
The cover is slightly recessed - it is lower then the bottom locking section and the top section with the camera. It also wraps around the sides almost 1/2 of the way.
I think that if the battery cover were coated with a rubberized, non-slip material, it would be better. If the rubberization made the cover stick out slightly, rather than be recessed, it would allow the phone to be set on it's back and not slide away and keep the camera off the deck. Also, the wrap around side parts of the cover would help when holding the phone.
Now, can someone tell me of a place/process that might do this? (Not rubber cement but close) My pickup has a Rhino Lining coating that I love. There is a place nearby that does that work but the coating is like 1/8-1/4 inches and that is a bit to thick for the phone.
Any Ideas?
http://www.plastidip.com/home_solutions/Plasti_Dip
http://www.brownells.com/.aspx/pid=1150/Product/GUN_KOTE_trade__OVEN_CURE__GUN_FINISH
http://www.goboatingamerica.com/products/DM_article.asp?id=3645
Found these
Bought this stuff at Home Depot.
Then tested in on this beer can. I didn't clean or prep the can, just picked it up off of the floor.
This is 5 coats. It is still thin. Dries fast and feels just about how I'd like it to. Not tacky - sort of a hard rubber feel. It is flexible, the can bends and the stuff stays with it.
It can be scratched, you may be able to see a scratch I made with my nail. It didn't go all the way through to the can though - and I had to scratch hard. It looks like it would be easy to spray another coat over any scuffs.
I plan to do the back of the battery cover - thick enough to make it a bit taller than the top and bottom sections of the phone. The way it is going it seem like that may take 15+ coats. I'll keep testing.
Two things about that though, the battery cover is used not only as the speaker output but the battery cover itself also dissipates a good amount of the heat that the phone generates. You probably want to be a more careful than usual in designing something that is going to smother this part of the phone.
not sure how much you're looking to spend but I put the Zagg total protection on mine. You get full protection on your phone but you can't see it, so you still get the sleek look and it's still very thin as well. The clear plastic is also great for gripping, I can set it on the dash of my car and drive normally and it won't budge.
I've had good luck with bestskinsever.com
Used it on my Nexus One and the fit was good, buddy got one for his vibrant and the fit is good as well.
journeyman82 said:
not sure how much you're looking to spend but I put the Zagg total protection on mine. You get full protection on your phone but you can't see it, so you still get the sleek look and it's still very thin as well. The clear plastic is also great for gripping, I can set it on the dash of my car and drive normally and it won't budge.
Click to expand...
Click to collapse
Looks interesting. I wish they had the leather skin for the captivate. I would be all over that. In fact I may need to take a trip to the fabric store to see what they have.
Thanks.
Ok to finish up my saga...
I liked the faux leather on the cover mentioned in the post above so I went to the fabric store and ended up with some black, I believe they call it marbled vinyl. It looked and felt similar to the back of a blackberry I once held.
I tested it on my trusty Busch Light can with some 3M spray adhesive and it seemed to hold fairly well.
So I went for it. I taped off the inside and the prongs of the battery cover. Sprayed glue on the cover and the back of a piece of vinyl cut too big. Stuck it on and smoothed it out. I sat the cover on a bag of rice and and put a bag of brown sugar on top (to push around the curves) and topped it off with a gallon jug of tile grout.
Waited an hour, probably longer than needed, and used a pointy x-acto knife to trim off the excess. I had also put a piece of tape over the speaker holes so I cut that back open to. The underside of the vinyl has a white background so once it was trimmed to fit I went around the edges with a fine tipped sharpie, which blended well.
Overall I like it. It is just a bit thinker that the top and bottom bands, so if you lay her on her back those parts don't touch a flat table. It has a leathery, grippy feel without being tacky, which is what I was going for. I do already miss the front edge lip that the Body Golve provided but it is also almost it;s original thickness.
Pics below. (Sorry about the crappy last pic. I had the phone with new back all set up on a white surface, ready for it's glamor shot, when I realized that the phone is my camera)
Staplebox: great job!
Wow that is a nice, careful job.....
staplebox said:
Ok to finish up my saga...
I liked the faux leather on the cover mentioned in the post above so I went to the fabric store and ended up with some black, I believe they call it marbled vinyl. It looked and felt similar to the back of a blackberry I once held.
I tested it on my trusty Busch Light can with some 3M spray adhesive and it seemed to hold fairly well.
So I went for it. I taped off the inside and the prongs of the battery cover. Sprayed glue on the cover and the back of a piece of vinyl cut too big. Stuck it on and smoothed it out. I sat the cover on a bag of rice and and put a bag of brown sugar on top (to push around the curves) and topped it off with a gallon jug of tile grout.
Waited an hour, probably longer than needed, and used a pointy x-acto knife to trim off the excess. I had also put a piece of tape over the speaker holes so I cut that back open to. The underside of the vinyl has a white background so once it was trimmed to fit I went around the edges with a fine tipped sharpie, which blended well.
Overall I like it. It is just a bit thinker that the top and bottom bands, so if you lay her on her back those parts don't touch a flat table. It has a leathery, grippy feel without being tacky, which is what I was going for. I do already miss the front edge lip that the Body Golve provided but it is also almost it;s original thickness.
Pics below. (Sorry about the crappy last pic. I had the phone with new back all set up on a white surface, ready for it's glamor shot, when I realized that the phone is my camera)
Click to expand...
Click to collapse
love it, im stealing that!
Go for it. Usually I prefer to buy a second of whatever I am defacing before I deface it but I didn't find any battery covers online. I also didn't look to hard.
It is still on and I still like it. The only thing I don't like too much are the sides. I completely covered the back, right up to the side edges. It is a perfect thickness on the back but feels too thick on the sides. I wish I could have found a thinner material that I could have built up on the back and tapered to one layer on the sides. I really wanted grippyness on the sides so, oh well, it's good enough.
I'm still on the look out for a better spray on rubber. I'll update if I find anything good.
Hopefully someone will start making aftermarket battery covers with some options.
Thanks and good luck,.
Second the stealing. Awesome idea and writeup. Thanks for sharing.
From a phone on an app
I scrapped the vinyl. The edges were just bugging me to much. I still think a thinner material would work well though.
I cleaned up the cover - looked fine again with all the glue off of it.
I went back to the rubber spray. I've got about 8 coats on in the attached pic. Need to wait about 30 min in between coats. I'll keep going until I go to sleep, let it dry overnight - and test it out tomorrow.
ETA - put it on the phone the today. Love it. Doesn't add any bulk and provides a grippyness to the back and sides. I'll find out how durable it is.

[Q] Cleaning the Leather Back?

Alright so I'm sure everyone who has the leather back and has not put a cover on it yet can see that the leather back is getting dirty.
It might be just me but i have the brown leather back. The stitches have gotten blackish and not white like they were in the beginning and the back just keeps getting a darker shade!
Any of you guys try to clean it? If so how'd you do it?
Is it okay to take the back off and clean it under water?
Or should i use windex.
I don't wanna ruin the leather attempting to clean it!
Areebkhan said:
Alright so I'm sure everyone who has the leather back and has not put a cover on it yet can see that the leather back is getting dirty.
It might be just me but i have the brown leather back. The stitches have gotten blackish and not white like they were in the beginning and the back just keeps getting a darker shade!
Any of you guys try to clean it? If so how'd you do it?
Is it okay to take the back off and clean it under water?
Or should i use windex.
I don't wanna ruin the leather attempting to clean it!
Click to expand...
Click to collapse
DO NOT USE WINDEX OR RUN WATER. That will ABSOLUTELY ruin your leather.
I bought a cheap bottle of leather treatment from CVS for about $6. You spray two coats on it, and you're good to go. It actually gave the leather a nice, grippy-er, feel. And it helps protect from wetness. After that, you should be able to use any type of leather cleaner to keep it looking fresh.
chadbot3k said:
DO NOT USE WINDEX OR RUN WATER. That will ABSOLUTELY ruin your leather.
I bought a cheap bottle of leather treatment from CVS for about $6. You spray two coats on it, and you're good to go. It actually gave the leather a nice, grippy-er, feel. And it helps protect from wetness. After that, you should be able to use any type of leather cleaner to keep it looking fresh.
Click to expand...
Click to collapse
HAHAHA!!
THANK YOUU!
I knew it was good to ask before doing something!
So cleaning it with that leather treatment gives it the shine back aswell?
chadbot3k said:
DO NOT USE WINDEX OR RUN WATER. That will ABSOLUTELY ruin your leather.
Click to expand...
Click to collapse
chadbot3k said:
DO NOT USE WINDEX OR RUN WATER. That will ABSOLUTELY ruin your leather.
Click to expand...
Click to collapse
chadbot3k said:
DO NOT USE WINDEX OR RUN WATER. That will ABSOLUTELY ruin your leather.
Click to expand...
Click to collapse
Quoted for emphasis. Definitely a very good thing that the OP asked.
I use Meguiar's Gold Class Rich Leather Aloe Cleaner followed by Meguiar's Gold Class Rich Leather Aloe Conditioner. Yes, I do my own auto detailing, and yes, I hate it when people use cleaners inappropriately and screw up whatever they were trying to clean. My parents are seriously guilty of that and it left me with cleaning-related faux-PTSD flashbacks decades later.
The G4's back wasn't shiny from the factory, but certain cleaners will produce a slight matte sheen on the leather.
Areebkhan said:
HAHAHA!!
THANK YOUU!
I knew it was good to ask before doing something!
So cleaning it with that leather treatment gives it the shine back aswell?
Click to expand...
Click to collapse
Yes, it will keep your leather back looking mostly new. Most importantly it will protect against getting wet, which will stain your leather.
Any kind of leather treatment that adds a "shine" is no good in my eyes. I have had a few european luxury cars and i can tell you this...best thing i have ever used to clean my seats and other areas has been...BABYWIPES!!
Seriously it does not take away from the natural state or satin look of the leather and actually clean it very well. If it good enough for your babys ass.....its good enough for the skin on your phone!
You dont have to take my word for it though.
BTW got it wet today. there was a slight dark spot for a fe minutes but went away fully
Snakecharmed said:
I use Meguiar's Gold Class Rich Leather Aloe Cleaner followed by Meguiar's Gold Class Rich Leather Aloe Conditioner. Yes, I do my own auto detailing, and yes, I hate it when people use cleaners inappropriately and screw up whatever they were trying to clean. My parents are seriously guilty of that and it left me with cleaning-related faux-PTSD flashbacks decades later.
The G4's back wasn't shiny from the factory, but certain cleaners will produce a slight matte sheen on the leather.
Click to expand...
Click to collapse
These kinds of products are unavailable outside the US so we need alternatives.
What do you make of the advice given in this video ?
House hold items available in any country.
white vinegar to clean
shaving foam to remove ink stains
corn starch to remove grease
From the user manual
This product is made of cattle hide and may have different creases and patterns due to the properties of natural leather. If the product gets wet with any liquid (water, soda, seawater, rain, sweat, sunscreen, cosmetics, moisture, etc.), it may lose colour, change colour, or deform in shape.
When this product gets wet or contaminated, get rid of the water by pressing it gently with a dry towel, or wipe it with leather cream and leave it to dry in shade. When the product is exposed to a wet environment for a long time, it may cause creases or mould. The shape of the leather may not be restored to its original state after cleaning because of the properties of leather, and any contamination or deformity may get worse when using regular detergent or an organic solvent.
When the leather is wet with rain or sweat, use caution and avoid contact with clothes. It can cause any dye to become a stain.
Due to the nature of leather, friction for long periods of time or excessive force may damage the surface of the leather.
Click to expand...
Click to collapse
This is an important thread or there's going to be a few unhappy people later on.
I used new baseball glove condtioner.
Sent from my VS986 using XDA Free mobile app
what i got is you need a cleaner and then a conditioner.
the cleaner to remove stains and a conditioner to maintain the material.
Mr clean magic eraser to clean it. That's what we use in the automotive detailing world
Sent from my LG-LS980 using Tapatalk
I don't know how I feel about the advice in the video. Those suggestions are very common, but I haven't tried them personally. People have conflicting things to say about the extreme acidity of vinegar against the mild acidity of leather, which is why you need to dilute the vinegar in the first place. One alternate suggestion I've read is to use Woolite 10:1 to 6:1 (water:Woolite). Another I've read is Dove soap. Don't use saddle soap, which has a pH level way too basic for leather cleaning.
What I can say is that you should use a soft terry or microfiber cloth to apply the cleaning solution, then wipe it off with a dry cloth. Don't apply a solution directly to the leather and don't apply too much at once. Even the moisture from a water-dampened cloth isn't the worst thing in the world if you're just quickly wiping on and off. Just don't soak the leather in anything, like running it under a stream of water. It's too porous to not absorb it. Once it's clean, condition it so you have some kind of protection from future stains.
As clichéd as this sounds, an ounce of prevention is worth a pound of cure. I'm not a super clean freak, but I try to keep my hands clean when I handle the G4. I don't touch the back of it while eating and I try to keep it away from beverages. However, I'm planning to get a plastic back for the G4 as my regular back cover and only use the leather occasionally.
Snakecharmed said:
I don't know how I feel about the advice in the video. Those suggestions are very common, but I haven't tried them personally. People have conflicting things to say about the extreme acidity of vinegar against the mild acidity of leather, which is why you need to dilute the vinegar in the first place. One alternate suggestion I've read is to use Woolite 10:1 to 6:1 (water:Woolite). Another I've read is Dove soap. Don't use saddle soap, which has a pH level way too basic for leather cleaning.
What I can say is that you should use a soft terry or microfiber cloth to apply the cleaning solution, then wipe it off with a dry cloth. Don't apply a solution directly to the leather and don't apply too much at once. Even the moisture from a water-dampened cloth isn't the worst thing in the world if you're just quickly wiping on and off. Just don't soak the leather in anything, like running it under a stream of water. It's too porous to not absorb it. Once it's clean, condition it so you have some kind of protection from future stains.
Click to expand...
Click to collapse
Thanks. Even with various leather cleaners around its a tricky affair to do it properly for the layperson. Not impossible. As long as one is aware.
As clichéd as this sounds, an ounce of prevention is worth a pound of cure. I'm not a super clean freak, but I try to keep my hands clean when I handle the G4. I don't touch the back of it while eating and I try to keep it away from beverages.
Click to expand...
Click to collapse
hehe, this advice will fall on deaf ears as its impossible to follow. Force of habit. it no secret that keyboards and touch screens contain more bacteria than toilet seats
However, I'm planning to get a plastic back for the G4 as my regular back cover and only use the leather occasionally.
Click to expand...
Click to collapse
Bingo! thats is the conclusion i'm reaching too. The idea of leather is fantastic but if you want to look good then be prepared to put in the work.
Leather is just not that practical for day to day in a phone usage scenario..
But it looks so good <sigh>
One of the things I've learned in both buffing/polishing and interior detailing is to not work too large of a surface area at once. You don't want to let a product set or dry before you can work on it. The product ends up being harder to remove and/or stains your surface.
When it comes to patina, the issue for me is that the leather surface is small, so any marks will be more visible. I look at my travel wallet, which I haven't used much, and I'm annoyed that there is wear on one of its corners and the color has rubbed off. I'm far less concerned about a scuff on the seat in my car. Still, I don't own any leather furniture because of the upkeep required.
There are photos one of the Android Central staff posted of a used brown leather Moto X. I don't think it looks bad, and if it came that way out of the box, I don't think anyone would have thought it was dirty. If you're like me though, you like keeping things looking like new. I'm getting better about conditioning or protecting new leather products before wearing them or breaking them in.
The black leather G4 cover would be much more forgiving with stains, but aside from lack of carrier availability, I only would have preferred that version if it had contrasting stitching.
Can someone point me in the right direction? I'm a complete noob at this and have no idea where to start. I was thinking of getting the leather honey conditioner from Amazon, but still wasn't sure if that would be appropriate. No clue where to begin on cleaners. I have the black leather back btw
xbayyx said:
Can someone point me in the right direction? I'm a complete noob at this and have no idea where to start. I was thinking of getting the leather honey conditioner from Amazon, but still wasn't sure if that would be appropriate. No clue where to begin on cleaners. I have the black leather back btw
Click to expand...
Click to collapse
I've had a bottle of Leather Honey since about 2000 (before they changed the name), and that's what I used on my leather back. It didn't darken the tan leather (unfortunately), though it did make it a bit sticky for a bit. If you go this route, apply it sparingly before going to bed.
Since this is a thread about cleaning, I feel obligated to mention that product is for protecting leather only, although I believe the same company makes a cleaning product as well.

How To Guide How to keep your case on the front of the phone

Alright, after months of trying to nail this problem down I finally have a good solution!
I've tried a few different cases on my fold3 and none of them really held well on the top screen when folded and in my pocket. It would start sliding off. So I finally have a solution. Get yourself some good double sided tape (I suggest some type of 3m tape This for example) and measure you a piece of tape that is length of the case that touches the phone that isn't on the screen. Then take a sharp knife and cut a very thin strip of tape. Put that strip on your case and then put the case on the phone. Press hard and hold it there for a bit and then BAM it's not going anywhere again. If it's done right it will not be noticable (see pics I've attached) unless you look closely it's really clean and nice looking to me.
In the pictures you can see the black strip of tape that came with the case that wasn't super useful but what useful was my piece of tape.
I have been lucky in that my cases have not had this issue, but I agree, if you need too, there is no shame in using tape to keep this thing protected.
Just use good quality stuff.
This is the stuff I have and I LOVE IT... https://smile.amazon.com/25Meter-Double-Adhesive-Display-Housing/dp/B071D5CKCX
Good solution, just easy.
Unfortunetly fold series and other folded devices need specially cover.
I have fold 2 1,5 year and few covers:
Ringke slim. Good cover but even pieces of double tape after take off i saw particles of dust and sand.
Next i bought Spigen armor pro. Great protection but a lot of bulky and even mount with force for good fit after few weeks and take off i saw few white dots on the frame from probably few particles sand.
It was little frustrating because I always to take care my devices and carry without any other stuff in my pocket.
4 days ago i told "stop" covers with use tape for hold on the device.
Without case fold is really beautifull and touch metal in every time is really pleasant .
I read topics on reddit about "caseless fold devices" and a lot of people have enjoy use folds without case.
After that I use my device only with original leather back cover, without front cover.
Admittedly 2 days ago drop my fold from pocket on the floor. It drop edge front frame but after that is only scratch and rest device survive well
I have béen using a dab of clear silicone sealant. Holds well, and comes off by rubbing it with a cloth.
After a few months of searching, I just gave up and use whichever is the slimmest case without an adhesive. It made more than a few scratches on the side of my screen and I just decided not to give a crap about it, it doesn't go over the main screen anyway.

Categories

Resources