Related
I guys, I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30.162, using MaUpgradeUt_noID and when update was complete I cannot load my JasJar anymore. I am using hard reset, but when choosing "0" off the boot screen - noting happens and screeen remains black.
Can someone please help me with this issue?
Thanks a lot in advance,
Best regards,
Stazik
Try reflashing it again. If it does not work, try reflashing back to the i-Mate ROM.
Whats the version of your bootloader (the screen with serial at the top changing to usb when plugged into usb)? If it is 0.56 or something else below 0.6 thats an already known problem.
I had similar problems with my O2 upgrade.
Try:
- Turn off USB in ActiveSync
- Hold Power/Light and press reset button
- Run the upgrade again
Thank you very much for help and support, guys!
When I try flashing my JasJar with Bootloader update or JASJAR_WWE_13076_164_10900_wwe_ship I get the same error message: Error 101 Connection Error. And also when I disable ActiveSync USB and plug my Jasjar into USB - I get a message from windows saying the device was not recognized...
The only I can get from JasJar is a black screen, except when I press two soft buttons and reset - that gives me a screen with 0 and x to choose. Neither of choices helps thou.
Any help is appreciated. Thanks a lot.
you didnt answer the question re the boot loader number.
when your screen is grey or starting to reset, there are numbers on the screen. what are they.
if it is less that 0.6 your in trouble and assistance is different to if your boot loader is 1.0 or similar.
My screen doesn't change from gray except when I do hard reset. And then I hit two buttons and reset, then press 0 the message Clearing now appears and then everything returns to gray again.
How can I tell the version of bootloader in this case?
Thank you in advance!
they are hard to see, if the screen is grey, the numbers are black.
f the screen is blue/coloured, the nmbers are probably red.
Thanks for help guys,
I brought my JasJar for service today, somehow they were able to put older ROM in there. Now I've upgraded bootloader, hopefully newest ROM from i-mate going to fit without problems )
Well I've killed my Jasjar upgrading I was installing the bootloader update. It sat there saying "Checking information on your device" for about 30 minutes after the update started (notes said it would take 10 so I figured something was amiss - disconnected & rebooted my PC.
Now when I turn the Jasjar on I get the USB/Serial screen referred to above and (good news I figure) it has v1.00 at the bottom. How do I fix this?
TIA
Sheesh. I did a search (I know I should have done that first) and found the answer here
Took a while to find a copy of mtty to download, but found that at http://buzzdev.net
Once I'd done the Set 14 0 and tried the boot loader update again it took seconds so something definitely went wrong the first time.
Hi there
The first time that I have attempted to perform the upgrade to a cooked rom and everything has gone horribly wrong.
A reset (using the pin hole) gives a blank display. Nothing at all.
A hard reset (using pin hole and soft keys) gives the option to perform hard reset by pressing Yes. This then gives HTC logo screen and then system hangs after displaying
IPL 3.13.0001
SPL 1.11.0000
I can go into bootloader screen (pressing two side buttons) and can connect USB. When I try to install factory ROM or any cooked ROM it stops at 2% and gives me an error saying
Error 228 - Invalid File Size
Is there anything I can do to save my device?
Please help.
are you sure that you have the right factory rom?
must be the one that was on your device when you bought it!
had the same problem! flashing with original rom solved it!
Yes - this is the WM5 rom that I had orginally before upgrading to WM6.
Bricked P3300
try and remove the minisd card
that must be the cause
cheers
jayzd1
Bootloader is not just by pressing two buttons. Press both the buttons and make a soft-reset. When the tri-color screen appears, connect to USB and perform the ROM upgrade again. If it fails, perform the upgrade with a factory ROM. This will bring back your device to working condition.
Next time before flashing, make sure you have applied Hard SPL once.
Regards,
Carty..
Hi all,
Just received my Vodafone-branded Diamond, and I'm afraid I already managed to brick it!
It was equipped with version "1.37.172.3 NLD" so I decided to upgrade it to the latest version.
The installation of OliNex Hard-SPL 1.93 went flawless, but the installation of ROM "RUU_Diamond_HTC_WWE-ME_1.93.456.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe" stopped at about 25% with error code 302. The recovery method that came with the package didn't help, every time the upgrade stopped at the same moment.
Since the device is stuck in the bootloader, and I'm left with a non-chargeable battery, I tried the official Vodafone-branded "RUU_Diamond_Vodafone_NL_1.97.172.4_Radio_Signed_Diamond_52.44.25.24_1.08.25.08_Ship.exe" ROM. Unfortunately, this upgrade stops at 48% and throws the same 302 error.
Anyone who can tell me what I'm doing wrong, and what I can do to solve all this?
I hope I don't have a brand new, but bricked device on Christmas!
TIA and have a nice day.
Try a hard reset first. If this doesn't help google or search at XDA for MTTY.
This tool can fix your device
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
Try this, maybe will work
Try a Vodafone branded stock rom before mtty.
Regards,
Carty..
He already tried a stock rom....
Potential Solution
Have you looked at the thread titled,
[UPG][TRBL]How-to fix: Update/Flash doesnt work, stops at 0% or 5% (invalid model ID)
It may just be a model ID glitch that can me fixed.
Take a look. It's in this forum in a sticky by cptsunshine.
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Besides, the bootloaders says upgrade ROM code error please try again.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Install Rom via Internal Memory Method
Steps from Suiller:
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
Let me know how it goes.
Make sure you have Net framework 3.5 installed on devices.
Nakkie27 said:
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Click to expand...
Click to collapse
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
band27 said:
Steps from Suiller:
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!
Click to expand...
Click to collapse
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
janielsen said:
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
Click to expand...
Click to collapse
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Nakkie27 said:
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Click to expand...
Click to collapse
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
janielsen said:
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
Click to expand...
Click to collapse
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on, and I can't get a USB-connection.
Edit:
Volume down + reset brought me in the bootloader again, although it's saying SPL-1.93.OliNex.
Nakkie27 said:
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on.
Click to expand...
Click to collapse
that i know but as i say in the post that when u do it that way i say u can load new firmware whitout it needs to boot try my friend i have done it 3 times because wrong loading of firmware
u have to only push thoose 2 buttom then it will work because u go to rescue mode
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Nakkie27 said:
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Click to expand...
Click to collapse
u need to hold them down until it leave the 3 color display an turns into grey
Ok, finally managed to do a hard reset. Afterwards I tried upgrading to the official Vodafone NL 1.97 ROM once more, but it failed at 48% again.
Any ideas what to do? I know have Diamond with Hard-SPL 1.93 (which says upgrade ROM code error) with no working OS.
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Hi all,
I have a quit similar problem. I've read a lot, but couldn't find an answer to my problem - may bye someone can help me.
I updated my Dimond (OliNex Hard-SPL 1.93, radio 1.09.25.23 and rom dutty V4). When I start my phone most of the time (95% plus) I end up in the color screen - however some time it's starts perfect (without changing anything).
When I get stock in the color screen, I can start the phone with mtty and the command "boot".
What can I do to make my phone always start in the normal way?
Thanks!
Nakkie27 said:
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Click to expand...
Click to collapse
i smell a radio issue - last time i was trying to upgrade my radio - ended up with something similar, managed it out like you did - but now you're up - so that's good!!
try some other rom (this time without radio) - i don't think you should have any issues going forward... good luck and have fun!
Hi,
i've a big trouble.
My diamond has the belite 0.99 ROM, which was installed thanks to the hdSPL 1.34.
I never have any pb changing ROM nor Radio rom too.
But, since this week, i want to change my rom for the AZTOR HD v1 or to change back to stock HTC rom.
But, i can't!
Every time i start the process, my diamond's screen turns into black, the microsoft active sync disconnects, then, the program for changing rom tells me there is a pb of connection!?? (error 238).
So i tried to change my hdspl to olinex 1.38 signed, but same result. Sometimes, when the upgrading program runs, i got a disconnection, or sometimes, the diamond's screen shows the 3 color screen with bootloader information. But, the process for upgrading fails every times!!
Any idea to help me please ???
What about 1.40 unsigned?
http://forum.xda-developers.com/showpost.php?p=2312363&postcount=2
i tried too!
this is really strange!
i have some difficulties to change my hdspl too!
i successfully changed from 1.34 hd to 1.38 olinex, but... i tried so much time and so much methods, i can't remember how i manage this change.
The fact is, to change ROM, or to change SPL, i got same results. Disconnection, black screen or boot loader screen..
Have you tried to flash from the internal storage? therefore bypassing the need to use Activesync.
you need to rename the ROM file (.nbh file) you have downloaded to DIAMIMG.nbh and transfer it to the root directory of the internal storage.
Ensure you phone is charged.
Now you need to hold down the Volume Down AND the "<-" button (the button just above end call) and press the stylus into the soft reset hole.
This will take you into the boot loader, keep the Volume Down, AND the "<-" button's held until you reach a grey screen you will be prompted to press the power button to perform the update to your phone.
Once it reaches 100% it will show "Update Success" and just sit there, at this point perform a Hard Reset, Volume Down AND the circle button and press the stylus into the soft reset hole.
Keep the Volume Down AND the circle button's held and you will be taken to another grey screen, prompting you to press Volume Up to perform the Hard Reset.
Try flash from BootLoader screen. There is Wiki that describe how.
lobsterdave>> thx, i'll try it after work today.
Lord_BlackAdder>> Flash from bootloarder ? where can i find this in the wiki please ?
Is it the same method described by lobsterdave ?
lobsterdave >> thx very much, it worked.
but i was only able to put htc official rom, not the cooked rom from aztor.
But no matter, now i can sell my diamond...
thx a lot, and happy new year to all!
Hi
My device has a German ROM.
I tried to Rom Upgrade to my O2 XDA III PDA but it doesn't work!
when i flashing the device it's freeze on process at%41 and give a error message. i unplugged the device craddle and flash same ROM again and process completed succesfuly. After all when i turn on my device ,there is only 3 Color on screen (Blue - Green - Red) and at the bottom of device is white. it writes R.1.10.00 at the right bottom of the screen.
Sorry about my english ! i searced it on web but i found a information and it tells find same type device and update ROM with FAT 32 Formatted SD Card.
Can anybody help me for Solve This Problem.
Thanks.
1. do you use vista/7 ?
2. did you forget to take out the sim and sd card during flashing?
that would be 2 possible reasons why you had the error in the first place.
now for the solution: if the flash was really complete and successful, which at this point you cannot tell by the success message, have you performed a proper hard reset?
the instructions on how to do that are to be found here: http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
power+reset, record+camera, then set the menu options to No, Yes, Yes confirm with the mail button.
rom upgrade through the sd card is generally not such a good idea, since it has never been fully confirmed, that and how it works.
if the hard reset does not solve your problem, you should read -=this=- really carefully and think whether you really did ALL the steps, they are all equally important.
Problem is getting worst !
Thanz chieff for your Help.
Problem is getting worst and confusing. i updated Radio version to 1.10.00 to 1.15.00. Device is turn on but it doesn't boot. My Device has no camera. When i plug it to creaddle it's orange led is ligthting and randon times it boots and 3 Colored screen shown. R.1.15.00 D.****** G******
HTC Blue Angel Windows Mobile 6.1 WWE only. But now it's do nothing. This morning i made hard reset to device and shown SERÄ°AM V.2.07 and put ,t to creedle and tried to Urgrade room but it gives error random positions etc. %54 or %89. ERROR 112
is my device dead???
Thanx you very much for helping me.
(Sorry About My English )
About my OS
i tried to upgrade XP Pro (SP2). Vista and Windows / is Not permission to upgrade...
if you're giving up, mail it to me. i should be able to tinker with it.