Related
Hi
I have just tried to update the rom on my xda exec (downloaded from the o2 microsite) it seems to load fine, but when i do a reboot I just get a wierd green & red speckled screen.
I have tried to update the rom twice now, once when the xda was on, & once from the bootloader screen.
Both times it seems to install correctly, but i get the strange screen.
HELP!!!
Add. My battery seemed to go to about 30% whilst i was updating. Could it be the battery? Can't charge it now to test. Can still get in bootloader screen.
PLEASE HELP!! Thanks
Same Here
I have exactually the same problem!
I downloaded the latest ROM from the My-XDA webiste (O2 Ireland) and it supports the XDA Exec as sold in UK and Ireland.
The upgrade goes fine but when I hard reset it just get a fuzzy screen full of red/green spots (lise interferance on a TV).
Have reinstalled the ROM from another PC and the same thing.
Can access the bootloader (v2.01) with no problem.
Have downloaded the ROM from another PC and tried from there and same thing?
Can anyone help?
Is there a known good ROM file that someone has used to rule out the file, as the XDA was fine until I ran the update.
Please help,
IrishLad
search be4 post
Update
I have tried 2 other ROM's on my XDA Exec and its exactually the same issue.
Once it gets flashed successfully and reboots i get the hazed screen which i cannot use. So its not the ROM file.
Has anyone got help with this, I have searched the posts already and found no solution that it why I have posted this thread.
Please Help,
Thanks,
IrishLad
So its not just me then! Thought I had cocked it up.
If this has already come up in these forums, I cant find it. Please at least send link to the previous problem if it is in here somewhere.
My XDA is dead!
Many thanks for your time & knowledge
Mark
try this one
try this configuration :
O2 XDA EXEC WM6 crossbow
Rom version : 2.02.00 WWE
ROM date : 03/10/07
Radio ROM : 1.15.00
Protocol version : 42.51.P8
ExtROM :UNLOCKED
have fun
the screen is funky but the xda is dead
I too am having this problem and am getting very frustrated.
I have searched the forum for hours and am not getting any closer to a sollution.
If anyone has resolved this problem in the past please send me a private message. I will love you forever if you do.
I had the same problem i think its a dodgy rom on the O2 website
I went into boot mode and used this ROM
http://forum.xda-developers.com/showthread.php?t=297256
Works a treat and is loads better than the normal o2 Rom
Thanks for the feedback
I have tried a few ROM's already with no success.
I will however try the ROM you posted and let you know if it works...
Thanks,
IrishLad
IT WORKED!
Not sure how, or why this worked.
But i installed the Crossbow ROM as listed previous and its working.
And can I just say the Exec is brillant now, its much faster, more responsize and works perfectly.
Thanks for the info, but I had tried 2 different ROM's previously and they never worked let I used one previously with no problems.
Either way I am now staying with Mobile 2006.
Thanks,
IrishLad
ukron is a god
YIPEEEEE!
IT WORKED
Thank you so much
I am very happy. Could you tell?
help
i have the same problem as you guys.
and more i can get my xda exec in to bootloader usb at the top and v2.01 at the bottom
but when i got to update it with the wm6 upgerade mentioned earlier
i get a connection error, please con somee one help
im using vista could this be the problem i have a hdd around some where that has xp on should i try that.
also i dont know is any of you knew but when ur in that messed up screen
if you press the lightbuld button a sort of i guess diagnostics or somthing screen pops up
Enable KITL NO
Clean Registry Hive NO
Formate Storage NO
you can change the no/yes's iv only got the enable kitl to do anything though. change it to yes buy using the buttons by the screen and then the center button it take you to the screen below
Select KITL Transport:
USB KITL
SERIAL KITL
ETHERNET KITL
Select KITL Mode:
ACTIVE
PASSIVE
any help with this will be appreciate
where can we find that crossbow wm6?????is that the one thats needed???
Someone please post a link 4 crossbow wm6 latest
would really b greatful...im it to me, email, or post it either way is good 4 me
THANKS,
Randy
no need problem solved....wm6 crossbow was def. needed
So i had 6.1 but it kept freezing, so I went back to 6.0, and was going to install 6.1 again...and now the screen goes to three colors, and then the installer box says "the image file was corrupted, please check your update utility"
and i dont know what to.
any help?
please and thank you.
First of all you the Kavana's & Rickwyatt's works on T-Mobile Dash, HTC S620 & S621 and you have to make sure your phone is unlock (use SDA Application unlock) to do it.
Try to use on these Upgrades, I recommend you Kavana's 6.1 cuz is easier to install with the (.exe) file but If you want T-mobile MyFaves the Rick's version came with it, Rick is a little more complicated for a lot of files included in the installation package but If you run (install.bat) and follow the steps. And Follow the instructions.
Kavana's: http://forum.xda-developers.com/showthread.php?t=374890
Rick's: http://forum.xda-developers.com/showthread.php?t=397845
Good Luck
Adavid
By the way, if the Phone got frozen remove the battery...I got T-mobile DASH and I have install both and work's good, the problems with Rick's the open applications close automatically if you don't use it.
Good luck again
Rick's 6.1
When you unzip Rick's package you have:
USPL <folder>
Auto
EnterBootloader
rapidtool
ROMUpdateUtility
.
.
.
Just click on Auto and follow the steps.
cant install rickys kavana rom
hello-i need help pls
while trying to execute ricks rom by autobat, after a few steps an error pops in that says cant find rom update utility, make sure u typed right..etc
can someone help
thx
*staring at the stickys...looking at the n00bs guide to installing 6.1*
*pointing and laughing at all who didnt read and follow it*
*going to bed*
gixxum said:
*staring at the stickys...looking at the n00bs guide to installing 6.1*
*pointing and laughing at all who didnt read and follow it*
*going to bed*
Click to expand...
Click to collapse
Think i may have a link to it on my sig just incase they can't read threadz?
Try This it will help a lot.
well
maybe im n00b- but still, while trying to flash i get an error massage that "windows can find romupdate utility" my phone is unlocked. so, ill appriciate ur help/
Did you UNZIP the zip file prior to running the auto.bat file??
anyone have any luck getting ubuntu installed on a s620? i get a message that says "you deserve to be punched square in the mouth." i want my phone to perform as a dns server, router, network storage and cell phone. it is app unlocked.
gixxum said:
anyone have any luck getting ubuntu installed on a s620? i get a message that says "you deserve to be punched square in the mouth." i want my phone to perform as a dns server, router, network storage and cell phone. it is app unlocked.
Click to expand...
Click to collapse
The correct distro you need is dashuntu, wow and i thought you knew it all
Can't remember off the top of my head what ubuntu is translated into? Something about tree huggers, so now we can be Dash huggers
yes i have.
ive restored my xp to earlier point , now ive managed to install the rom.
for some reason i get a daily update from microsoft, seems to me they f*** my system.
the-light said:
yes i have.
ive restored my xp to earlier point , now ive managed to install the rom.
for some reason i get a daily update from microsoft, seems to me they f*** my system.
Click to expand...
Click to collapse
Glad you got it sorted.
On computer go Start\Control Panel\Automatic Updates and you can turn them off.
Turn off that Microsoft update B.S.
PLEASE ASSIST: I'VE RECENTLY UPGRADED MY CINGULAR/ATT 8525 HERMES UNIT TO WINMOB6 AND NOW CAN'T GET PAST THE INITIAL WINDOWS MOBILE SCREEN WHERE IT SAYS "TAP THE SCREEN TO SET UP YOUR WINDOWS MOBILE BASED DEVICE." (THE TOUCHSCREEN SEEMS TO BE DISABLED) ALSO, NOW ACTIVESYNC WILL NOT CONNECT TO THE DEVICE. I'M AT A LOSS AS TO WHAT ELSE TO DO (TRIED HARD RESET SEVERAL TIMES WITH SAME RESULT). IF SOMEONE COULD POINT ME IN THE RIGHT DIRECTION - I'D SURE APPRECIATE IT.
ETUMON said:
PLEASE ASSIST: I'VE RECENTLY UPGRADED MY CINGULAR/ATT 8525 HERMES UNIT TO WINMOB6 AND NOW CAN'T GET PAST THE INITIAL WINDOWS MOBILE SCREEN WHERE IT SAYS "TAP THE SCREEN TO SET UP YOUR WINDOWS MOBILE BASED DEVICE." (THE TOUCHSCREEN SEEMS TO BE DISABLED) ALSO, NOW ACTIVESYNC WILL NOT CONNECT TO THE DEVICE. I'M AT A LOSS AS TO WHAT ELSE TO DO (TRIED HARD RESET SEVERAL TIMES WITH SAME RESULT). IF SOMEONE COULD POINT ME IN THE RIGHT DIRECTION - I'D SURE APPRECIATE IT.
Click to expand...
Click to collapse
hmm no need to scream.
Push the OK on left and power on right, and stick stylus in all at the same time. Re run the exe file while it is plugged in to active sync, and see. Which WM6 did you use?
Sorry I'm new at this. I used WM6.1. Which exe file do you want me to re-run. ActiveSync is offline....I can't get it to connect to the unit. Thanks for your assistance.
ETUMON said:
Sorry I'm new at this. I used WM6.1. Which exe file do you want me to re-run. ActiveSync is offline....I can't get it to connect to the unit. Thanks for your assistance.
Click to expand...
Click to collapse
Ok, since you're on ATT I suggest you follow my instruction above, get into tricolour screen (bootloader), and download this
from the post above you will get the shipped ATT rom. Don't worry if activesync is saying is not connected, just run the file. You will then get back to a WM6.
The phone originally came with WM5 and I was upgrading to mess around with the thing. I'm at the tricoloured screen and now downloading the files from RapidShare. Will this get me back to WM5 or to the upgrade. If there is a way, I like to try the HardSPL flash I've been reading about today - will this work on either WM version? Txs & Rgds.
ETUMON said:
The phone originally came with WM5 and I was upgrading to mess around with the thing. I'm at the tricoloured screen and now downloading the files from RapidShare. Will this get me back to WM5 or to the upgrade. If there is a way, I like to try the HardSPL flash I've been reading about today - will this work on either WM version? Txs & Rgds.
Click to expand...
Click to collapse
After you have flashed this WM6.0 you really need to flash hard SPL first, I thought you would have done that already.
Really please read this first before you brick your phone.
No that's the thing. I'm just finding out how I went about this all wrong and maybe shouldn't have been messing this in the first place. Anyhow, my bootloader screen reads like this:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
ETUMON said:
No that's the thing. I'm just finding out how I went about this all wrong and maybe shouldn't have been messing this in the first place. Anyhow, my bootloader screen reads like this:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
Click to expand...
Click to collapse
Well follow mrvanx guide, that's all I had to get on with few months ago.
Many thanks for the advice. So just to be clear I should first run the file I downloaded from RapidShare to get me back to a working WM version, then follow mrvanx guide to flash Hard SPL or viceversa...
ETUMON said:
Many thanks for the advice. So just to be clear I should first run the file I downloaded from RapidShare to get me back to a working WM version, then follow mrvanx guide to flash Hard SPL or viceversa...
Click to expand...
Click to collapse
I have not tried to hardspl a non working phone sorry so I have no experience with that. Give it a go first, and report back.
Still Stuck
zocster said:
I have not tried to hardspl a non working phone sorry so I have no experience with that. Give it a go first, and report back.
Click to expand...
Click to collapse
Nope, didn't work. Here's the report:
ERROR [260]: UPDATE ERROR
The update utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA phone.
Check the following:
1. The PDA Phone is connected to the USB cradle/cable.
2. The USB cradle/cable is connected to the PC.
Is there another way to establish comunication with the PDA other than through ActiveSync? Somekind of emulator box or binary software???
ETUMON said:
Nope, didn't work. Here's the report:
ERROR [260]: UPDATE ERROR
The update utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA phone.
Check the following:
1. The PDA Phone is connected to the USB cradle/cable.
2. The USB cradle/cable is connected to the PC.
Is there another way to establish comunication with the PDA other than through ActiveSync? Somekind of emulator box or binary software???
Click to expand...
Click to collapse
hmm weird, so have you got .net framework installed on your PC? try it again one more time while in bootloader, plug the phone to USB as long as you can hear the 'ding' sound you should be OK. I have 'bricked' my phone a few times and this always work. What are you trying to flash? the hardspl or the ROM?
Yes, today I upgraded to .net framework 3.5 when ActiveSync failed Microsoft Error took me to their website and offered me the option. I had been running 2.x .net framework and never had a problem would also use same ActiveSync with my old Axim X30.
Yes, I can hear the 'ding' sound and I was trying to run the file RUUWrapper.exe (Hermes ROM Upgrade w/ the option Force using SSPL).
well that shows the other way around doesn't work, so you need to get your phone to a working WM6 state, how is your download going from rapidshare? get it to boot loader mode again and flash that exe file.
Just completed that route - I ran the PDA Phone ROM Update Utility 3.12.3.7 - the process took about 10 minutes to go through 100%, then it restarted and stayed at the Window Mobile screen for little over minute (crossing my fingers), but then just showed the same message "Tap the screen to set up your Window Mobile based device." Please let me know if you have other avenues to try – It’s close to 4am here in Miami, but I'm not sleeping. I’m really glad you are able to assist with this mess – thanks a lot!
ETUMON said:
Just completed that route - I ran the PDA Phone ROM Update Utility 3.12.3.7 - the process took about 10 minutes to go through 100%, then it restarted and stayed at the Window Mobile screen for little over minute (crossing my fingers), but then just showed the same message "Tap the screen to set up your Window Mobile based device." Please let me know if you have other avenues to try – It’s close to 4am here in Miami, but I'm not sleeping. I’m really glad you are able to assist with this mess – thanks a lot!
Click to expand...
Click to collapse
so did you follow it through? and it didn't fix it? you have some bad blocks?
Unfortunately, you need to have some sleep, and read these when you wake up
http://forum.xda-developers.com/showthread.php?t=296722
http://forum.xda-developers.com/showthread.php?t=369434
zocster said:
so did you follow it through? and it didn't fix it? you have some bad blocks?
Unfortunately, you need to have some sleep, and read these when you wake up
http://forum.xda-developers.com/showthread.php?t=296722
http://forum.xda-developers.com/showthread.php?t=369434
Click to expand...
Click to collapse
what does bad blocks mean?
Okay, looks like I've got a Type 2c Brick Situation in my hands.... I think I will take your advice and get some rest and tackle this again later on. I really appreciate your assistance - will you be around again later?
Okay good day, I'm back on the trail. Found shipped ROM on WIKI for HERMES in the following thread - http://forum.xda-developers.com/showthread.php?t=277664
Downloading now...According to pof(moderator) it's a "new rom from the still unreleased Cingular 8525: HTC Hermes (HERM100) branded from U.S. Operator Cingular"
My only question then would be that this appears to be made for WM5 and I performed the WM6 upgrade which is what got me into this mess in the first place - so will there be any conflicts or issues I should now about? I'm about to go ahead with it - if anyone is out there and thinks otherwise, please advise soonest. Thx & rgds, Ed
ETUMON said:
Okay good day, I'm back on the trail. Found shipped ROM on WIKI for HERMES in the following thread - http://forum.xda-developers.com/showthread.php?t=277664
Downloading now...According to pof(moderator) it's a "new rom from the still unreleased Cingular 8525: HTC Hermes (HERM100) branded from U.S. Operator Cingular"
My only question then would be that this appears to be made for WM5 and I performed the WM6 upgrade which is what got me into this mess in the first place - so will there be any conflicts or issues I should now about? I'm about to go ahead with it - if anyone is out there and thinks otherwise, please advise soonest. Thx & rgds, Ed
Click to expand...
Click to collapse
Sounds good man!! Flash it!! oem WM6 roms usually fix allot of issues.. Don't be scared everyone else is busy flashing WM6.1 roms all the time now!
Thanks for the words of support <joshkoss>! Just attempted several times to flash the Shipped ROM I found from <pof> (PDA Phone ROM Update Utility - R:31300 D:51000 U:31101 P:0) and keep getting ‘ERROR[260]: UPDATE ERROR’ message. While instead I went back again to flashing the ROM that <zocster> suggested last night (PDA Phone ROM Update Utility 3.12.3.7) and it does go through the entire 10 minute process until it shows 100% completion both on the PDA and on the PC and then tells me congratulations….etc. I even flashed it twice back-to-back as I read to do in one of the threads – but just keep getting back to the dreaded Window Mobile screen with the same message "Tap the screen to set up your Window Mobile based device."
My next question is this: Why does the PDA Phone ROM Update Utility 3.12.3.7 connect to the PDA, but the PDA Phone ROM Update Utility - R:31300 D:51000 U:31101 P:0 (which I read is the Shipped ROM that I need to get the PDA back to) gives me an error message. Obviously, there is a connection since I’m able to get a 100% completion on the other ROM??? Please kindly advise…..
Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!
I have the same Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU value and i was able to restore my phone to working status with the following ROM
http://www.megaupload.com/?d=IJIVTIMF
Hope this help
10507
Thank you very much 10507! I'll download it now and see if it works.
Thanks for the file but it appears that it is for the SDA. It dit not work
luisro said:
Thanks for the file but it appears that it is for the SDA. It dit not work
Click to expand...
Click to collapse
That's odd, I was able to restore my Excalibur/Dash after flashing the corrupted EnergyRom.
Hope you will find a way to resolve your problem.
10507
But how did you do it? Flashing it through USB or through the memory card? The weird thing is that when I run the EXE the cellphone that appears in the picture of the program is an SDA. But well I will try it again and thank you for the help!
I used bootloader method and connected my phone through USB for flashing. Remember to remove your memory card when flashing.
well, I've been in your situation for almost 3 days now, and still no solution for it, maybe it's time to put it in the box and purchase a new one , all thanks to the broken EnergyROM ...
Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.
ookba said:
Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.
Click to expand...
Click to collapse
Thanks ookba for cheering us up. I'm having the same problem like many, many people in this forum hopeless seeing our dash not responding to every solution proposed in this forum and the only thing that we have right now is keep trying to flash and see if it works. I will try again in different PC and see what happens. I'll let all of you know if I finally resurrect my s621.
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
This problem is ridiculously weird to why some members are able to restore their phone to original factory condition, and others are not able. Therefore, I have search from trustworthy sites and from friends for difference made ROM. Hopefully, one of these ROMs with help out anyone...........
1.33.422.1 (Worldwide English, WM6)
http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
1.27.405.1 (Worldwide English, WM6)
http://rapidshare.com/files/100235639/HTC_S620_WWE_1.27.405.1.exe
1.22.531.6 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?z4vjgzxisrz
1.22.531.4 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?yygkw1d5xmc
1.11.531.1 (T-Mobile USA, WM5)
http://rapidshare.com/files/104641948/T-Mobile_DASH_WM5_V_1.11.531.1.exe.html
Excalibur_BRIGHTSTAR_PTB_1.30.514.2_4.1.13.47_ 02.98.90_Ship
http://www.mediafire.com/?9gbwdzd2omg
Thanks 105507 but no success at all, I even found 2 more factory roms in the web and also they don't work. I own an unbranded international version s621 manufactured by Brightstar corporation (I tried to flash Brightstar's stock rom but it didn't work) and I noticed this because in the warranty docs it says brigthstar corporation and originally the phone came with WM5.
not that this will help. but this is one of the reasons why people should be really installing the hardspl so if you have a bad flash, you dont have to install a stock rom. any rom whether be it cooked or not will work. but this hardspl must be done prior to installing ANY rom. the hard spl is done by jockyw2001. send him a pm to see if theres anyway to get that on the phone, even in its current state.
edit: here's the link to the hardspl: http://forum.xda-developers.com/showthread.php?t=329605
luisro said:
Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!
Click to expand...
Click to collapse
My phone is the same your phone but ONBL 1.33.0000 and SPL 1.33.0000
I'm trying to find the original rom of this line but not found. Please help me!
Have you done a reset? My friend fixed his by trying reset a few times. He reset it, walked away...., it took long time to see whether it booted over; if not, do it again...
By the way, he leave the sim card in; and, you need to remove your micro sd card.
On an official site it is possible download ROM for your phone. It is flashing from bootloder mode. It some times helped me, while I have not flashed hard SPL.
luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
Hi my friend, I wish you lucky!!!
by the way, where country you're from, I have some Shipped Roms here for brazilian Excalibur (S621), maybe it could help, if the answer is yes, let me know to made this one come to you
http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard
Furious Girlfriend (oh My beloved Helloween died with my ROM's)
Boy oh Boy...
My ROM's are now in heaven
Girlfriend deleted they (I'm so sorry...)
But, pay attention in this thread
http://forum.xda-developers.com/showthread.php?t=381726
In there have a sort of shipped ROM's and maybe coud help you
Good luck my friends
A friend from XDA have some Shipped Rom's and will upload it for you, shortly he'll post something here
hello everyone..
this morning I was intended to revert my kaiser back to WM 6.1,
I followed the instruction to put the ROM to my SD card along with KAISDIAG.nbh.
but maybe I chose a wrong rom, as the process goes, I just realize that the process was deleting my hard SPL..
now the text my 3 color display only says "SPL-1.56.0000"
but the android is still working....
so now my phone run on android without hard SPL...
could anyone help me? is it possible to install a hard SPL from android?
flashing from SD card doesn't works because I don't have any hard SPL installed..
There is no way at present to install hardspl from android, since we cannot run jumpspl, however you should still be able to flash a stock 6.1 rom using usb method.
Sent from my HTC Dream using Tapatalk
I have tried, but the process always failed with connection notification.It says that update utility cannot connect with my pda phone.
Well the problem is, flashing with usb method needs activesync connection with the computer. since microsoft activesync doesn't applicable anymore, I have no idea how to build connection with my phone. Besides, nothing seems happened every time I connect my phone with usb cable. Its just like my pc couldn't detect the device.
Should I install some kind of programs first on my pc? or am I miss some steps to make my phone detected by my computer?
I'm using windows xp by the way..
The CustomRUU still works for me if you boot the phone into SPL first (reset and camera+power buttons) then plug it into the computer and run the RUU (no activesync connection), so you should be able to flash a WM ROM, then you can sort out the HardSPL later
EDIT: Or does that only work for me because I have already got HardSPL?
yes it works..
the process goes, but only for 1 % . my phone reset itself and the notification on my pc says about invalid vender ID "this update utility cannot be used for your PDA phone, please check your update utility."
since the only stock rom that I found is .exe which is extract itself, I couldn't use The CustomRUU. Could this be the problem? or do I choose a wrong rom?
edit : I'm trying to install Factory Shipped ROM form HTC
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship
Do you know where to find stock rom for kaiser? most of the post about stock rom leads me to wiki xda, which is not available anymore.
thanks.
Not sure if these will work, but there are links to original HTC and ATT ROMs here
Also at the bottom of that post is a link to some reconstructed original ROMs
I have no idea if these will work any better than the one you've already tried, but it's probably worth having a go
thanks for the link..
I have visited that thread before, actually the 1st ROM that I tried to flash is also from that page. Both original ROMs for HTCor ATT doesn't works for my phone. But thanks to you I just realize the link about some reconstructed original ROMs.
Well, My phone is KAIS-100 which is made in Taiwan.
I guess I'll try Chinesse HTC 1.56.708.3.
I hope this one will make a progress.
-----------------------------------------
aww... still not working..
with reconstructed ROM, the process stuck at 0%, give me error [262] notification : update error. The manual said that if this kind of error occurred, I just need to do soft reset and run RUU again. I have tried several times even restart my pc first, but still not working.. any suggestion?
Try to flash radio. If you can't do it i think that you have messed up the bootloader
I can't...
the result is same, I'm trying to flash KAIS_Radinly_1701909 or KAIS_RADIO_ONLY_1710901_Custom, I got stuck in 0% with error [262]
The text in my bootloader says
KAIS-100
SPL-1.56.0000
CPLD-8
So, is there nothing else I could do if I have broke my bootloader?
No one can help me anymore? T-T
(running to the middle of the street and shout "why God, why??")
So, the lesson is :
If you are trying to flash back to windows mobile, DO NOT use factory shipped rom. Because it will modify your hard SPL and downgrade your radio version.
If the process failed and your hard SPL gone, you will get stuck in half working android without being able to flash anything, including correct your radio version, or reflash your kernel to fix your panel setting.
correct me if I'm wrong..
well, I hope my experience could be useful for you.
Thanks.
You can extract the exe file with winrar and you'll have all the files including RUU_signed.nbh
Rename it to kaisimg.nbh and copy to sdcard
Don't know if you can install from sdcard but since it's the shipped rom it might let you.
thank you salac..
I also have tried that method, using winrar to extract exe files.
but still, no luck for me..
Flashing via SD card got me stuck at loading screen, and I also tried to use custom RUU to flash the files via usb but my phone reset itself at 1% of the process and gives me error message [294] : invalid vender ID.
SOLVED
Finally
after days of yearning..
I found a suitable WM 6.1 ROM for my kaiser.
My phone is KAIS 100 HTC P4551. Usually, KAIS 100 model is for AT&T but mine is HTC branded, so that's why AT&T stock ROM won't works and my phone was originally shipped for US, that's why most of WWE stock ROMs always give me error 294.
So, basically I have to use HTC WWE ROM for US and this is really gives me hard time since HTC US website only provide ROM for AT&T.
In case you have same problem with me, I have uploaded the ROM at rapidshare
and you could find it here.
Now, I can flash a hardSPL, fix my radio version....
and flash back to android..