sx56 ATT stuck in 'upgrading; will only take........' screen - Upgrading, Modifying and Unlocking

Hi y'all
I've tried unlocking my SX56/XDA from ATT and all went well using the XDAUnlocker tools and roms etc...., but.....
while 'flashing' the rom my pc crashed and rebooted. now my sx56 is stuck in the 'upgrading; will only take 5 minutes' screen. I've tried a hard reset and that don't work. I can't even get the phone connected with activesynch
Can anybody help me please??
Thx; a newbie

Update
Just sat here and browsed the forum for any possible help regarding my problem; there is a solution I'm going to try out.
Flash the rom (build w/ lumpistefan rom kitchen) via bootloader with SD card; now all I need is to buy a SD/MMC cardwriter and I'm on my way.......
Will let you guys know what happens because I've found more peeps with the same prolem.
Oh a quick note: I've bootloader 5.22 and it does recognize a new rom when inserting a SD card with rom; it will ask you to format or download....... Well here goes nothing
L8R

As long as you can get to bootloader it should be fine for sd flashing.

All worked fine
Ok all worked fine; i'll include a step by step (found here ain the forum and will give credits to it) later. i'm kinda in a hurry....... When i upgrade from pc02 to wm03 will i loose all data? if i backup and try to reload data it will not except it?

Please thank these people
I fixed my sx56 with help from these guys after searching and searching
please thank these guys for the solution because all credits go to them.
http://forum.xda-developers.com/viewtopic.php?t=9675

Related

wallaby problems...

i have tried and tried to figure out the problem with my wallaby. I have spent days searching through this website looking for answers and to no avail...
here is the problem:
the unit was dropped and won't get past the tmobile screen
here is what is on the screen...
g324e4
r6.25.02
4.01.16
I have gone through the tests and everything passes...it just won't go past that screen
I can't activesync, but I do have an SD card
I do not know how to use the SD card to get a new ROM or anything on the phone...furthermore I don't know how to get my windows mobile back on it...
any help would be GREATLY APPRECIATED!! I know I am new...and I did make more than a serious effort at trying to figure it out on the forums...but I have been unsuccessful...
thanks...
ichiwawa2001 said:
i have tried and tried to figure out the problem with my wallaby. I have spent days searching through this website looking for answers and to no avail...
here is the problem:
the unit was dropped and won't get past the tmobile screen
here is what is on the screen...
g324e4
r6.25.02
4.01.16
I have gone through the tests and everything passes...it just won't go past that screen
I can't activesync, but I do have an SD card
I do not know how to use the SD card to get a new ROM or anything on the phone...furthermore I don't know how to get my windows mobile back on it...
any help would be GREATLY APPRECIATED!! I know I am new...and I did make more than a serious effort at trying to figure it out on the forums...but I have been unsuccessful...
thanks...
Click to expand...
Click to collapse
You have to use the SD Flashing method in order to import the new rom, there's several posts How-to concerning this matter otherwise if you want you can cook a rom from this website, it contains some helpful links
http://lumpistefan.dyndns.org/
http://www.romkitchen.de/tools/form.php
Ps: Don't play with your "RSU" Radio stack..

Help! M5000ruu.exe load failed now now device!

Had a search but cant find anything on here to help.
Downloaded M5000ruu.exe from Orange.
Followed instructions, including sof boot of device.
Connected via AS,
Ran the install program again.
Install program halfway through complainied it could no longer see the device.
M5000 rebooted and now all i have is USB v2.01
Have tried removing battery, and done hard reset, with both options tried, but neither come back with anything.
AS ver 4.1.0. (build 4841)
USB was direct connect not through Hub.
What do I do now???
Thanks in advance! :twisted:
also happened by me. not with this rom. mostly hard reset several times will help/ otherwise reinstall this rom when this won't work ( what i did ) installed official qtek rom aku 2 later reinstalled new rom et voila...
good luck
Having read a few more threads I feel a bit happier that Im not the only one to have this.
Just tried again having left battery out for some time and seems to be going through now.
Scary as hell though
Thanks for your reply
remember: when updating rom remove phone sim AND memory card !!!!!!

Very Strange Brick Problem

Hi guys, I've read and used the forum for years and upgraded my Cingular 8525 a ton without troubles (followed Vanx's method for vista and for upgrading), but this is the first time I'm really stuck without a clue.
I had Schaps latest OS on my phone working fine for about three days. It was charging with the USB hook up to my Computer. I pulled the USB out and the phone entered bootloader. I couldn't get it out. I tried using mtty to no avail, hard reset ect., but finally used the SD loading method to put TNT's latest on it (don't know why this worked). Here's the thing though, the phone will load fine on first load after I flash, but if I soft reset or turn the phone off and on it goes right into bootloader mode. The only way I can get it to load up again is to connect it to the computer's USB, take out the battery and then put it back in. the OS then boots up without fail.
I have read a ton and searched on the forum, and if any of you can help me understand what the hell I can do to fix my phone I would really appreciate it. I will post anymore info you guys would like, I really need your help on this one.
Thank you so much!
Hi,
I posted exactly the same problem today ! here:
http://forum.xda-developers.com/showthread.php?t=381284
It's really strange !
Dave
I've been reading everything and it appears that Schaps's new version seems to have this problem sometimes....I have the exact same problem as everyone else (mtty gives me the same results), and flashing a new rom doesn't get rid of it....I hope there is some way to fix this!
maybe I'll try flashing a new radio and see if that helps things....
I did notice that flashing Schaps 4.31 seems to include radio 1.50 and I had changed my anyway to 1.43 as I thought that was better for my area.
Not sure a radio will help. Maybe a different ROM version will ? Maybe 3.54 ?
I have flashed TNT's rom as well and it still has the problem now....I'm flashing a new radio as I type, I'm going to have to reflash the OS too, it just got stuck again as it was restarting.
Just a quick thing, I think I have solved my problem (not sure if it is permanent) by powering the phone off and on. Not resetting, just a simple power off. I spoke to a colleague who said the way it shuts down is different to soft reset (makes sense) and I haven't powered my phone off properly for a long time.
I have tried soft reset a couple of times since doing this and it hasn't gone to the bootloader screen once.
Maybe this is the simple fix.
I will keep you posted.
try to flash OFFICIAL ROM first , maybe there are few bug / missing file when error appear while flashing other ROM.
I hope it will help you both.
rgds,
ermen
Use mtty to see if yo have any bad blocks... I've had a few problems the same as yours and found I had 1 or 2 extra bad blocks, after the 2 "factory standard" bad blocks I got on my jasjam of course. hope this helps...
My fix didn't work.
Not sure what I am suppossed to see when I run "task 2a".
Has anyone had any luck fixing this ?

Need hepl guys PLEASE

Hi, i have been trying for the last month and a half to try another rom on my hermes,but it seems i can't.
i have flashed many Roms and i never had a problem in doing that till the las time when i tried to flash into the new S64.
every time i try flashing into any new rom it rejects me by giving me the (ERROR 260) telling me i'm not connected and the USB cardle thing, but all of my connections are correct and my ActiveShyn is up to date and i was always flashing roms in the same way.
Some seniors here when i have mentioned that told me that it seems i have flashed or reflashed the Hardspl, so i'm trying to reflash the Hardspl, i have tried endless times but it keeps telling me the same althought i have downloaded almost every hardspl that is available in the xda site lol.
what i'm requesting please if possible to direct me in the steps that i need to make my hermes functional again please i'm sure u understand what i'm saying.
some have mentioned that cause i still have the
herm100 i can't flash it into another roms but that sounds a bit strange lol.
I know that i have still herm100 (old) and my ipl-1.01
and spl-1.06 but i think that dosn't matter in my opinion.
Please i request if u can help me in fixing my problem by providing me the steps by simple words and if you have a fresh zips of hardspl coz i'm so confused which one to use, it would be nice to hear how to do it step by step.
i really need your support and excuse me if i'm bothering u with this kind of request but i didn't know where else to go and ask.
My Current rom is the HTC_Hermes_S64_WM_6[1].1_HTC_WWE_v2_30.03.2008 which is old and i would like to refresh my phone by a new version.
i was thinking of the new HTC_HERMES_S64_WM_6.1_TouchFlo2D_UC_ WWE v3 / GER v1 but i don't know if it would work on my herm100 cause i was told it was designed for herm200 and abouve is that true?
If not well there are so many more roms out there i would like to try but i'm stuck for the moment.
please again i wouldn't have bothered u with my request if i wasn't facing this problem.
thank u a lot and i hope to hear soon from u commrade.
Dayhauck.
have you tried to manually go into the bootloader and flash? You don't need activesync to flash like that if you're connected with USB. Also, from your SD card. Both have worked for me in the past.
Though you should have Hard SPL installed if you want to use the sd card method.
i have tried to do it manualy but i not much of a luck in loading the Hard SPL.
I really don't know what to do. i can't even f;ash to the original htc rom .
what else can i do?
1. Check your usb cable.
2. Try different USB ports in ur PC,
3. Check if the mini USB in Hermes is not damaged.
4. Check the bootloader if you have HardSPL installed.
5. Try SD method,
6. Read the wiki.
check out post 1160 on page 116 of this thread for sd card method for Hard SPL V7 - http://forum.xda-developers.com/showthread.php?t=296722
Cheers...
I had the same problem. If you can activesync with the cable then all you need to do as already mentioned above.
With the phone attached manually go into bootloader (hold on/off on right of phone and 'ok' on the left of phone both in while you prod the phone reset at the bottom of the device).
When you have the multicoloured boot loader run the update and it should work fine.
Hope this is some hepl

Energy ROM semi bricked my Dash, help needed! (And appreciated)

Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!
I have the same Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU value and i was able to restore my phone to working status with the following ROM
http://www.megaupload.com/?d=IJIVTIMF
Hope this help
10507
Thank you very much 10507! I'll download it now and see if it works.
Thanks for the file but it appears that it is for the SDA. It dit not work
luisro said:
Thanks for the file but it appears that it is for the SDA. It dit not work
Click to expand...
Click to collapse
That's odd, I was able to restore my Excalibur/Dash after flashing the corrupted EnergyRom.
Hope you will find a way to resolve your problem.
10507
But how did you do it? Flashing it through USB or through the memory card? The weird thing is that when I run the EXE the cellphone that appears in the picture of the program is an SDA. But well I will try it again and thank you for the help!
I used bootloader method and connected my phone through USB for flashing. Remember to remove your memory card when flashing.
well, I've been in your situation for almost 3 days now, and still no solution for it, maybe it's time to put it in the box and purchase a new one , all thanks to the broken EnergyROM ...
Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.
ookba said:
Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.
Click to expand...
Click to collapse
Thanks ookba for cheering us up. I'm having the same problem like many, many people in this forum hopeless seeing our dash not responding to every solution proposed in this forum and the only thing that we have right now is keep trying to flash and see if it works. I will try again in different PC and see what happens. I'll let all of you know if I finally resurrect my s621.
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
This problem is ridiculously weird to why some members are able to restore their phone to original factory condition, and others are not able. Therefore, I have search from trustworthy sites and from friends for difference made ROM. Hopefully, one of these ROMs with help out anyone...........
1.33.422.1 (Worldwide English, WM6)
http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
1.27.405.1 (Worldwide English, WM6)
http://rapidshare.com/files/100235639/HTC_S620_WWE_1.27.405.1.exe
1.22.531.6 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?z4vjgzxisrz
1.22.531.4 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?yygkw1d5xmc
1.11.531.1 (T-Mobile USA, WM5)
http://rapidshare.com/files/104641948/T-Mobile_DASH_WM5_V_1.11.531.1.exe.html
Excalibur_BRIGHTSTAR_PTB_1.30.514.2_4.1.13.47_ 02.98.90_Ship
http://www.mediafire.com/?9gbwdzd2omg
Thanks 105507 but no success at all, I even found 2 more factory roms in the web and also they don't work. I own an unbranded international version s621 manufactured by Brightstar corporation (I tried to flash Brightstar's stock rom but it didn't work) and I noticed this because in the warranty docs it says brigthstar corporation and originally the phone came with WM5.
not that this will help. but this is one of the reasons why people should be really installing the hardspl so if you have a bad flash, you dont have to install a stock rom. any rom whether be it cooked or not will work. but this hardspl must be done prior to installing ANY rom. the hard spl is done by jockyw2001. send him a pm to see if theres anyway to get that on the phone, even in its current state.
edit: here's the link to the hardspl: http://forum.xda-developers.com/showthread.php?t=329605
luisro said:
Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!
Click to expand...
Click to collapse
My phone is the same your phone but ONBL 1.33.0000 and SPL 1.33.0000
I'm trying to find the original rom of this line but not found. Please help me!
Have you done a reset? My friend fixed his by trying reset a few times. He reset it, walked away...., it took long time to see whether it booted over; if not, do it again...
By the way, he leave the sim card in; and, you need to remove your micro sd card.
On an official site it is possible download ROM for your phone. It is flashing from bootloder mode. It some times helped me, while I have not flashed hard SPL.
luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
Hi my friend, I wish you lucky!!!
by the way, where country you're from, I have some Shipped Roms here for brazilian Excalibur (S621), maybe it could help, if the answer is yes, let me know to made this one come to you
http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard
Furious Girlfriend (oh My beloved Helloween died with my ROM's)
Boy oh Boy...
My ROM's are now in heaven
Girlfriend deleted they (I'm so sorry...)
But, pay attention in this thread
http://forum.xda-developers.com/showthread.php?t=381726
In there have a sort of shipped ROM's and maybe coud help you
Good luck my friends
A friend from XDA have some Shipped Rom's and will upload it for you, shortly he'll post something here

Categories

Resources