Just received my case from AliExpress.
Very thin and first impressions are favourable although I'm tempted to put a thin clear film over the joint between the case and mini screen in the corner in case the edge flexes and scratches the screen.
Construction is a very thin hardshell rear with a plastic flip and a smoked translucent corner on the front.
Clearance for the cameras on the rear is minimal.
There's a small square magnet visible on the flip below the widow for the hall sensor to let out acts as a smart cover.
Using miui12 always on screen and smart case options gives a small clock and battery indicator in the window.
Can see the height difference between the Xiaomi smart cover and the leather case I had before.
The orange is muted and the Matt dark grey of the phone holder contrasts nicely.
Hopefully the mi10 won't get as warm with this case as it did with the leather one!
Does it affect (reduce) the screen on lateral ?
bernardblt said:
Does it affect (reduce) the screen on lateral ?
Click to expand...
Click to collapse
What do you mean by lateral?
That might not have translated well
The screen turns off when you close the case and turns on when you open it.
I highly suggest not using this case! it leaves a mark on your display exactly where the glass plastic part begins. because it is not perfectly flush with the leather part.
I used mine for about a week and have a permanent scratch on the display the entire length of the plastic window.
B!GBOY said:
I highly suggest not using this case! it leaves a mark on your display exactly where the glass plastic part begins. because it is not perfectly flush with the leather part.
I used mine for about a week and have a permanent scratch on the display the entire length of the plastic window.
Click to expand...
Click to collapse
That's not good!
Mine the plastic is recessed away from the screen slightly so it shouldn't make contact.
I put a piece of clear gorilla tape over the joint anyway
I take it you don't have a screen protector fitted?
Mine came with one
fards said:
That's not good!
Mine the plastic is recessed away from the screen slightly so it shouldn't make contact.
I put a piece of clear gorilla tape over the joint anyway
I take it you don't have a screen protector fitted?
Mine came with one
Click to expand...
Click to collapse
nope mine did not come with a protector! which is odd cause everyone got theirs with a protector already applied. At the time I assumed this product would protect the display until my glass gets here but... it did the opposite -_-
I don't use this case even now that i have the glass on my phone because it limits the ways I can use it.
It looks dumb when taking photos because the thing just flaps in the air also cannot use my gimbal or my bike mount. all in all not my best purchase
B!GBOY said:
nope mine did not come with a protector! which is odd cause everyone got theirs with a protector already applied. At the time I assumed this product would protect the display until my glass gets here but... it did the opposite -_-
I don't use this case even now that i have the glass on my phone because it limits the ways I can use it.
It looks dumb when taking photos because the thing just flaps in the air also cannot use my gimbal or my bike mount. all in all not my best purchase
Click to expand...
Click to collapse
mine didnt come with screen protector on either an i have mi10 cn an mi10 eu
-fluffy- said:
mine didnt come with screen protector on either an i have mi10 cn an mi10 eu
Click to expand...
Click to collapse
Seems odd that some do some don't.
Mine is 8gb/256gb EU version
B!GBOY said:
....have a permanent scratch on the display the entire length of the plastic window.
Click to expand...
Click to collapse
I can't believe plastic is able to scratch the gorilla glass display.
"Glass scratches at a level 6 with deeper grooves at a level 7". -Jerryrig
I would guess you have an screen protector. I didn't see mine at first because ist sits perfect.
Looking at the notch is where i could see it on my phone.
Dabiolos said:
I can't believe plastic is able to scratch the gorilla glass display.
"Glass scratches at a level 6 with deeper grooves at a level 7". -Jerryrig
I would guess you have an screen protector. I didn't see mine at first because ist sits perfect.
Looking at the notch is where i could see it on my phone.
Click to expand...
Click to collapse
I didn't believe it either but my phone did. lol
Be my guest and try for yourself. I don't know the technical term but the screen has some sort of coating as it's top most layer and the case made a permanent mark on the glass if you clean it perfectly it's not visible. But as soon as you touch the display that part will get dirty almost instantly. Another example, if i use an alcohol wipe the outline of the window on the display retains moisture and the rest does not. So call it what you want but this case damages your display.
my solution was to clean the display perfectly and put a "Hydrogel" (marketing BS for plastic foil) on top. I totally forgot about it until you quoted my post
Oh you mean the oleo phobic coating. Been there already because i was so "smart" and had washed my first smartphone display with dishwashing soap and was wondering why it was getting dirty even after cleaning.
Later I found a solution:
https://www.ifixit.com/Guide/How+to+Restore+or+Apply+an+Oleophobic+Coating/9682
Related
I am one of those who likes the phone as is.
Why cover/thicken it up? And gorilla glass sure as heck shouldn't need protection as it only reduces the sensitivity and usefulness - why buy a touch screen if you don't want to touch it in the first place.
BUT
2 days on the TGV's across France and Switzerland and boy was I cursing; the bloody phone slid everywhere ... so it made me think.
Got home and stuck 2 of those clear rubber/plastic kitchen cupboard door dome bumpers (Magnet for those in the UK) on the corners by the camera, and voila you have a non-slide phone and protects the lens at the same time.
Works for me, also helps the grip as your fingers go between the domes.
Each to their own. Hope its helps some.
major c said:
I am one of those who likes the phone as is.
Why cover/thicken it up? And gorilla glass sure as heck shouldn't need protection as it only reduces the sensitivity and usefulness - why buy a touch screen if you don't want to touch it in the first place.
BUT
2 days on the TGV's across France and Switzerland and boy was I cursing; the bloody phone slid everywhere ... so it made me think.
Got home and stuck 2 of those clear rubber/plastic kitchen cupboard door dome bumpers (Magnet for those in the UK) on the corners by the camera, and voila you have a non-slide phone and protects the lens at the same time.
Works for me, also helps the grip as your fingers go between the domes.
Each to their own. Hope its helps some.
Click to expand...
Click to collapse
I also hate casing, but... I hate scratches and dents more.
I've found mine is getting scratched on the 'bump' below the samsung logo. Stupid bit of design that put the most scratchable plastic on the entire phone on the only surface that touches the table.
I like mine au naturel too but it looks like we've no choice but to use a skin or case if you don't like scratches.
Sent from my GT-I9100 using Tapatalk
That "bump" actually stops the camera lens from getting scratched when place on a flat surface.. dunno why they didnt recess the lens though... or better still stick a lens cover on it!!
Im a case fan personally, yeah I love the look of the phone, but I want it to stay that way.. so Ill wrap it up! makes for good resale value near end of contract!
I stuck a strip of clear sellotape across the hump, prevents scratches until something better pops up
The sellotape works wonders!
I don't care scratches but the reason why I use case is the camera lens because it can be easily scratched and will take worst photo
.:SiLvErHuNk:.
I have a case an cheap one i bought on eBay and it works fine but ive ordered another one and am going to buy a screen protector - SGP Ultra Oleophobic Film which appears to be the best available, when you've spent €450 on a phone the last thing you want is for it to be scratched
major c said:
Why cover/thicken it up? And gorilla glass sure as heck shouldn't need protection as it only reduces the sensitivity and usefulness - why buy a touch screen if you don't want to touch it in the first place.
Click to expand...
Click to collapse
Holy cow. Who said Gorilla Glass won't scratch? Jeez. Of course a good screen protector is recommended and also a good case which will protect the device if it drops accidentally.
Regards.
I have got a visible scratch right between the camera lens and the flash....missed both of them...Phew!!!...
so now I have a case always fitted, SP and also a cut out SP for the lens...
Hi
I bought a oneplus one about 3 months ago and I absolutely love it however I dropped it a while ago and everything is fine but the frame area to the left of the charging port is completely jacked up :/ chunks of it are missing too...
I'm currently using the oneplus flip cover however it doesn't cover it up, so my question is: is there any light tpu/hard shell case that covers up the entire silver bezel, or at least the bottom of the phone so I don't have to look at this anymore xD. All cases I've seen so far leave a bit of the bottom frame exposed just enough so you can see the damage :'(
Anyone know any case that can cover it up?
Thanks!
I advise you to look for the "Diztronic" TPU case, covers completely the silver frame, following the contour of the screen. There's just a 1 cm spot where the frame is visible, at the bottom of the cover, near the hole for the USB cable, but in normal use is not visible. It's 6 months that I'm using this cover in combination with a tempered glass and I'm really satisfied.
Guess it all depends on what kind of protection you want. If you just want mild protection and to just cover the sides, then go with the tpu case. If you want heavy protection, I would suggest the Tudia Omnix Hybrid, http://www.amazon.com/TUDIA-Full-body-Protective-Protector-Resistant/dp/B00SO4XYHA . I have the Tudia case and it has taken a beating and protected the phone very well, even from some pretty high falls. Only con about the Tudia case, is that the front covers the sides of the screen a bit and prevents touch at the the very edges of screen. This can be a bit bothersome if using apps in full screen/landscape when you have to swipe down to exit full screen.
noahvt said:
Hi
Anyone know any case that can cover it up?
Thanks!
Click to expand...
Click to collapse
kenboyles72 said:
I would suggest the Tudia Omnix Hybrid
Click to expand...
Click to collapse
I too have a Tudia--Slim-fit Cygen.
thanks
thanks
Bino92 said:
I advise you to look for the "Diztronic" TPU case, covers completely the silver frame, following the contour of the screen. There's just a 1 cm spot where the frame is visible, at the bottom of the cover, near the hole for the USB cable, but in normal use is not visible. It's 6 months that I'm using this cover in combination with a tempered glass and I'm really satisfied.
Click to expand...
Click to collapse
I totally agree, couldn't have said it better. Here are some visuals for you. I got the Diztronic case when I bought the phone, it has protected it from falling out a car, off the desk, and off a moderately high shelf. You can get a tempered glass screen protector off eBay, have to search a bit (TechArmor don't have one). I got one from user dreamlight2004 for around 5 dollars. I made the mistake of getting the OPO screen protector when i first got my phone and it went bad a month ago, a hard scratch from a key. Tempered glass protector looks so much better. Just loaded COS13, it should keep me busy until the OP3 gets announced - so far it's looking to be a really good phone (boo on the OP2 and OPX)
Case view
Phone view
I agree, Diztronic bumpers are terrific.
I'm using this one http://www.ebay.com/itm/Rearth-Case-OnePlus-One-Folie-Ringke-Fusion-Schutzhulle-Cover-Tasche-klar-/121715293296?hash=item1c56cbfc70:g:gAUAAOSwT6pVt5tV And it is awesome. You can also print your designs for this case!
Ringke Fusion for me is great. It covers the OPO completly.
DO NOT BUY THE TUDIA CASE.
I bought it because I thought it looked pretty sweet. It's the worst case I have ever owned, and I have owned a few. Half the case is slippery nonsense plastic. You grab your phone "wrong" (by this I do not mean insecurely, but simply you happen to not have your fingers on enough of the case's rubber outline), it's like holding an eel.
The clips covering the audio jack and usb port are an absolute NIGHTMARE to open, and plugging in your charger for the night would realistically take three hands with 17 fingers each to manage in a reasonable timeframe. Good thing my audio jack's clip, after having been used exactly twice without even the slightest bit of the abuse it deserved, now no longer clips into it's crevice, and is permanently hanging out at a 30 degree angle. The pop-out clip on the back is nail ruining torture to get out, as is the rubber outline holding the front of the case, should you want to get this garbage off to see how far you can launch it through the air in rage.
I wouldn't use this piece of junk if they paid me.
I am using the TUDIA Dual-Layer case+a glass screen protector, which turned my One to a tank
I drop it way too often, but it still works flawlessly, so I can recommend this case. It also coverers the aluminum frame
I can rep the Poetic Case found here:
I took out the screen protector but I have been rocking the case for more than a year. It is kinda bulky but I have no worries about dropping it or tossing my phone on my desk. Also, It is kinda water resistant (with the screen protector). I have dropped like a glass of water on it and quickly cleaned it up with no harm
Since there don't seem to be any tempered glass screen protectors that cover the entire screen and stick properly to the curved edges, I'm looking for the next best option.
What is the best protective film for the V20?
So far, I have come across these two on eBay:
1. Nillkin HD Clear Crystal Transparent Thin Phone Screen Protector Film For LG V20
2. 2x Mikvon Armor Screen Protector for LG V20 Retail Package with accessories
Anyone have experience with either of these protectors? Are they worth buying?
I tried to find Skinomi on eBay but shipping to my country is not available.
Note. International shipping is important.
http://www.skinomi.com/lg-v20.html
have you checked their website
ricohz said:
http://www.skinomi.com/lg-v20.html
have you checked their website
Click to expand...
Click to collapse
Yes I did but the shipping costs are way too high, at U$9.95 + U$4.00 it would cost more to ship to my country than the cost of the screen protector itself.
I got this one and it rocks! It goes all the way to sides and it doesn't attract fingerprints, without compromising the screen quality!
https://www.aliexpress.com/item/Ful...-Clear-Use-Layer-2nd-Gen-TPU/32770113161.html
The Armorsuit screen protectors have always treated me well. They seem to be clearer/have less of a "fuzz effect" than the others I've tried. They're wet application if that matters to you. I personally think it makes the process easier.
https://www.amazon.com/gp/aw/d/B01JU43FQ2/ref=cm_cr_arp_mb_bdcrb_top?ie=UTF8
Byte_76 said:
2. 2x Mikvon Armor Screen Protector for LG V20 Retail Package with accessories
Click to expand...
Click to collapse
Mikvon goes from edge to edge. However it does not stick to the top and bottom curve of the phone. You will have a gap and it slowly collect dust. Also if you have a case, it might push on to the SP on the side.
ronaldyeo said:
I got this one and it rocks! It goes all the way to sides and it doesn't attract fingerprints, without compromising the screen quality!
https://www.aliexpress.com/item/Ful...-Clear-Use-Layer-2nd-Gen-TPU/32770113161.html
Click to expand...
Click to collapse
Does this one have the problems I describe above?
ronaldyeo said:
I got this one and it rocks! It goes all the way to sides and it doesn't attract fingerprints, without compromising the screen quality!
https://www.aliexpress.com/item/Ful...-Clear-Use-Layer-2nd-Gen-TPU/32770113161.html
Click to expand...
Click to collapse
Is this wet application? How much room is on the side? I use spigen case and looking for screen protector that doesn't interfere with it.
If the screen protector goes from edge to edge it has tendency to be peeled off by case.
Also does it cover entire screen from top to botton included lg logo?
Not a wet application. Just a dry one - you'll get quite a bit of bubbles but they clear up within a day. It's got about 1mm at the sides, cutting it a little close - slight off and you'll have that halo issue which I solved by snipping a bit off whichever corner.
eRRoRist said:
Mikvon goes from edge to edge. However it does not stick to the top and bottom curve of the phone. You will have a gap and it slowly collect dust. Also if you have a case, it might push on to the SP on the side.
Does this one have the problems I describe above?
Click to expand...
Click to collapse
So far, I haven't seen such a problem. No dust or lint collecting on the sides. but like I mentioned, slight alignment issues and you'll probably have to trim it off using a cuticle scissors or something - that's what I did. :good::good:
Here's a video for reference. Pardon the quality, I got the cam for christmas so just fooling around with it.
https://youtu.be/R3K5P8B-aiI
ronaldyeo said:
So far, I haven't seen such a problem. No dust or lint collecting on the sides. but like I mentioned, slight alignment issues and you'll probably have to trim it off using a cuticle scissors or something - that's what I did. :good::good:
Here's a video for reference. Pardon the quality, I got the cam for christmas so just fooling around with it.
https://youtu.be/R3K5P8B-aiI
Click to expand...
Click to collapse
Looks good!! Thank you for the detail review!!
It's definitely better then the Mikvon I got. The ads say "gold..." and the pic shows a tint of gold?? Don't see that in the video though, so it's just a normal TPU SP?
http://forum.xda-developers.com/v20/accessories/finally-screen-protector-t3533549
It's tempered and no issues at all. I'm loving it.
eRRoRist said:
Looks good!! Thank you for the detail review!!
It's definitely better then the Mikvon I got. The ads say "gold..." and the pic shows a tint of gold?? Don't see that in the video though, so it's just a normal TPU SP?
Click to expand...
Click to collapse
The gold is just the top film used during application. It's really just clear. Not too sure how a TPU SP is like but I reckon yes, it's just a normal clear version.
One word of advice, don't try to remove the cut-outs when you're removing film 1, leave it there, it's easier to remove that way - I learnt that the hard way.
Here's it now, the bubbles are pretty much gone and I haven't done anything specific to it. Perhaps playing some swiping games pushes the bubbles away :laugh:
https://youtu.be/ISTsEnkTVj0
Bump. Anyone find anything yet? Tried the highly recommended skinomi and that thing is crap. If you want to feel like you're touching an inner tube for a bike (minus the dirt) enjoy. But I can't stand that rubber feel. Ordered a different PET type from Amazon, hasn't come yet but hoping I'll have luck. Wet installations suck. And absolutely hate tempered glass. So, anyone have any PET type protectors to recommend that cover the whole screen?
Found one. Non-tempered glass, no orange peel feel, fits perfectly. 5$ on Amazon. Orzero LG V20 Screen Protector https://www.amazon.com/dp/B01GO1YXFQ/ref=cm_sw_r_cp_apa_3r5XybWYKE83Q
Here's photos of it installed.
Try this one. Lifetime warranty.
https://www.amazon.com/gp/aw/d/B06X94J77F/ref=ya_aw_od_pi?ie=UTF8&psc=1
shadowswittness said:
Try this one. Lifetime warranty.
https://www.amazon.com/gp/aw/d/B06X94J77F/ref=ya_aw_od_pi?ie=UTF8&psc=1
Click to expand...
Click to collapse
This thread is for non-tempered glass tho. I am one of few that hate the idea of covering glass with.... glass. Kind of an oxymoron in my eyes. Lol
pre4speed said:
This thread is for non-tempered glass tho. I am one of few that hate the idea of covering glass with.... glass. Kind of an oxymoron in my eyes. Lol
Click to expand...
Click to collapse
Sorry about that. I misread the title.
pre4speed said:
Found one. Non-tempered glass, no orange peel feel, fits perfectly. 5$ on Amazon. Orzero LG V20 Screen Protector https://www.amazon.com/dp/B01GO1YXFQ/ref=cm_sw_r_cp_apa_3r5XybWYKE83Q
Here's photos of it installed.
Click to expand...
Click to collapse
Is it wet installation?
Also does come from side to side all the way? I just worry that might peel on the edges ones I put my case on.
netgar said:
Is it wet installation?
Also does come from side to side all the way? I just worry that might peel on the edges ones I put my case on.
Click to expand...
Click to collapse
Nope, dry install. If centered correctly upon installation, it is complete full coverage. My tip is to get a deep steam in your bathroom, and make sure your hands are clean. I have no lifting from my case and I got a case that the phone slides into. It has been perfect since install. Only 1 comes in package, but lifetime warranty. I highly recommend it.
Hey guys! Just thought I'd share my experience trying to hunt down the best screen protector for my Galaxy S10e.
After trying about 4 different glass protectors all with pinch hole camera cut outs and being dis satisfied with the look and feel of the edges I decided to try one that came with a solid glass that covered the front entirely. It also had a super thin black boarder that I wasn't entirely convinced I was going to like.
Turns out it is AMAZING!! Phone looks literally as if there is nothing on. Edges are completely smooth so no more scratchy feeling whenever I slide my finger to use the edge display or gesture navigations.
Totally felt I had to share this! You can search for it on Amazon! :highfive:
Link: amFilm Glass Screen Protector for Galaxy S10e, Tempered Glass, Full Screen Adhesive, with Easy Installation Tray (Black) https://www.amazon.com/dp/B07PP9Q288/ref=cm_sw_r_cp_apa_i_59LYCbQZEMHN9
Share the name and link maybe? Is it case friendly? Do the black edges cover up some screen or leave everything visible as before?
The same?
https://www.amazon.de/amFilm-Schutz...film&qid=1556700491&s=gateway&sr=8-1-fkmrnull
reikar said:
Share the name and link maybe? Is it case friendly? Do the black edges cover up some screen or leave everything visible as before?
Click to expand...
Click to collapse
Sorry wasn't sure if I could share a link i just added it to the OP. Yes it is case friendly and I belive the black border covers a super small part of the screen that is a fraction of a millimeter. When using edge lighting all you need to do is increase the thickness a bit.
However it does not get in the way at all and from my experience it is way better than other screen protectors I have tried that have transparent as they reflect the light at angles. Also the borders look terrible during the day, you can clearly trace it with your eye. This one literally reflects no light and looks like if there is nothing on it at all (the black border provides this effect)
Furthermore, this one comes with a plastic frame that makes placement and alignment such a breeze!
Hope that helps!
NisseGurra said:
The same?
https://www.amazon.de/amFilm-Schutz...film&qid=1556700491&s=gateway&sr=8-1-fkmrnull
Click to expand...
Click to collapse
Yea that's it!
Another good one is the tempered glass from Skinomi. It also comes with a install frame and they're 7.99 for a three pack. Look great, install quickly and cover pretty spot on.
dmdelgado said:
Yea that's it!
Click to expand...
Click to collapse
Just got it, pretty good. Easy installation with the supplied frame.
Recommended.
stay-down said:
Another good one is the tempered glass from Skinomi. It also comes with a install frame and they're 7.99 for a three pack. Look great, install quickly and cover pretty spot on.
Click to expand...
Click to collapse
I didn't know Skinomi make temper glass, just film.
Sent from my SM-G970U1 using Tapatalk
Is the amFilm full glue? (not only on the sides?)
Never mind..... from Amazon: Bubble Free Guarantee, Full Screen Adhesive, Designed for easy installation with included Easy Application Tray!
And the Skinomi?
MasterThiefGarrett said:
Is the amFilm full glue? (not only on the sides?)
Never mind..... from Amazon: Bubble Free Guarantee, Full Screen Adhesive, Designed for easy installation with included Easy Application Tray!
And the Skinomi?
Click to expand...
Click to collapse
I think Skinomi is regular plastic, spray. Maybe I missed it but I can't find temper glass made by Skinomi.
Sent from my SM-G970U1 using Tapatalk
If anyone wants to order from Aliexpress, CHYI brand always made great screen protectors, either hidro, film, tempered... I might try them out on the s10E soon.
Deleted
dmdelgado said:
Turns out it is AMAZING!! Phone looks literally as if there is nothing on. Edges are completely smooth so no more scratchy feeling whenever I slide my finger to use the edge display or gesture navigations.
Totally felt I had to share this! You can search for it on Amazon! :highfive:
Click to expand...
Click to collapse
Tried this because of your recommendation (and after trying 5 different "perfect" protectors) - it is really great and totally worth the money! Thanks, pal
Got the Nillkin glass protector -> https://www.nillkin-case.com/index.php?route=product/product&product_id=6425
It's covering the whole display, with black borders around it(they eat 1-2mm from the actual display).
Very happy about it. Bought it at a locat shop with about 20 euros.
amFilm for Samsung S10e by TechMatte
I Love this screen saver
amFilm for Samsung S10e by TechMatte
Very easy install with alignment tool, nice squeegee tool got all the bubbles out. Looks excellent after install was complete. Will update in a few days to see how it look after a few days of use but so far so good. Was probably the easiest Tempered glass screen saver I have ever installed, very satisfied
Bought this exact screen protector because I wanted something inexpensive and without a cam cutout (I'd rather deal with an additional layer of glass on a front camera I anyway never use than with dust piling up in a tiny cutout). Well, I don't share OP's enthusiasm. A corner started to shatter appart after only a week, and I didn't even drop it or anything. It was in the same pocket as my lighter which might be the culprit but c'mon, if it can't handle a lighter and turns into a H8 shards dispenser that soon, how is it supposed to prevent scratches on the screen ?
Another corner got damaged after a 50cm (metric FTW) drop on wooden floor and I decided to get rid of it altogether.
It's cheap, it's easy to apply, it looks good (although the black border overlaps the screen by maybe half a millimeter), and it might last a bit longer for someone less careless than I am, still not a viable long term option according to me.
Rob_lochon said:
Bought this exact screen protector because I wanted something inexpensive and without a cam cutout (I'd rather deal with an additional layer of glass on a front camera I anyway never use than with dust piling up in a tiny cutout). Well, I don't share OP's enthusiasm. A corner started to shatter appart after only a week, and I didn't even drop it or anything. It was in the same pocket as my lighter which might be the culprit but c'mon, if it can't handle a lighter and turns into a H8 shards dispenser that soon, how is it supposed to prevent scratches on the screen ?
Another corner got damaged after a 50cm (metric FTW) drop on wooden floor and I decided to get rid of it altogether.
It's cheap, it's easy to apply, it looks good (although the black border overlaps the screen by maybe half a millimeter), and it might last a bit longer for someone less careless than I am, still not a viable long term option according to me.
Click to expand...
Click to collapse
Sucks you had a bad experience with it. So I ended up reaching out to them after myself finding my screen protector had cracked and they sent me another one for free.
It probably isn't the strongest screen protector but it's cheap, easy to install, and looks great! It's TRUE the protectors with the hole punch are a haven for dust and just look hideous in general.
If you stumble across a better screen protector I'd love to hear about it! Perhaps I'll try it out next if this one tanks on me again
Cheers!
dmdelgado said:
If you stumble across a better screen protector I'd love to hear about it! Perhaps I'll try it out next if this one tanks on me again
Click to expand...
Click to collapse
I should receive one from LK in a couple days, let's see how it holds. I cannot ask for a replacement, I'm french and they offer replacement only in america, but this time there's 3 in the package.
Does the amFilm protector black edge cover visible part of the screen like Nilkin does? Nilkin protector black sides cover also OLED visible screen (half mill on each side).
sikita said:
Does the amFilm protector black edge cover visible part of the screen like Nilkin does? Nilkin protector black sides cover also OLED visible screen (half mill on each side).
Click to expand...
Click to collapse
Yes it does. I have one installed now and it cuts off a sliver on each side
Just can't find a front and rear case that I'm 100% with. They are mainly to Bulky or to flimsy.
Ao at present I'm using front, rear and hinge 'screen protectorso
Think I might be being foolish though. Guarantee I drop it now!
Same here actually. I have the Armid case from Samsung but I usually prefer phone naked so it is the same with Fold 2. I didn't remove yet the inner screen protector but planning to.
I was using the phone without any protective case because like you said, none of them fits 100% to my liking, and guess what happened. I have dropped the phone from 2 feet and cracked the edge of the front screen. I couldn't sleep for 2 days how upset I was, but fortunately my local Samsung care center replaced the screen right away for roughly $150.00, but they installed new front screen that has absolutely no factory screen protection, so I am using the phone naked outside. Yesterday my Ringke case arrived so I put it on immediately, just in case but it's not perfect. But I will have to live with it. I am receiving Samsung Aramid case tomorrow, so I will see which one I will keep on the phone.
I don't know if this idea is good to remove the inner display protector. I don't do this. for what ? perhaps scratches in the inner display ? not for me
has anybody removed the outer display protection ? I think this is not a big problem cause gorilla glass victus is here.
D.J.ChriZZ said:
I don't know if this idea is good to remove the inner display protector. I don't do this. for what ? perhaps scratches in the inner display ? not for me
has anybody removed the outer display protection ? I think this is not a big problem cause gorilla glass victus is here.
Click to expand...
Click to collapse
It doesn't matter what sort of glass it is, if you look at the right hand side corners the glass is bulged out so any impact there will 100% shatter it. I had/ have a note 20 ultra with a broken screen, still under repair (for more than a month now) so don't completely trust the victus branding.. glass is glass and glass breaks :crying:
D.J.ChriZZ said:
I don't know if this idea is good to remove the inner display protector. I don't do this. for what ? perhaps scratches in the inner display ? not for me
has anybody removed the outer display protection ? I think this is not a big problem cause gorilla glass victus is here.
Click to expand...
Click to collapse
I removed the inner screen protector as I didn't like the feeling of it. It was also very difficult to keep clean of fingerprints and smudges and I was unable to see past that.
Now, the screens looks and feels ALOT better, but I've noticed some small scratches on the screen. They appear to come from my left thumb nail while scrolling. Even though I keep my nails fairly short. The scratches are only visible when the screen is off an from the right angle. I can't feel them, but they can be wiped away.
There aren't enough bad scratches to bother me yet and I don't regret removing the protector... but I thought you should know.
If the scratches get bad, I'll get a screen replacement and maybe consider a protector... but I'll only keep the phone for a year, so it'll probably be naked again even after a replacement ??
I went naked as well for tha same reason I couldn't find a good case...stock screen protector inside and out!
No protectors inside or out, no case, pure naked. It's a joy to run this way but one little drop later I could be weeping like a schoolgirl with a skinned knee. That window ends in about a week as I finally found a case as premium as the phone and I'll be in a wallet soon.
I use only this for carring the phone.
this fits very good !
https://www.fjallraven.com/de/de-de/kinder/accessoires/kanken-pen-case?_t_q=&_t_hit.id=Luminos_Storefront_Web_Features_Catalog_Product_Domain_CommonProduct/CatalogContent_91278d42-b27b-47e1-ae7b-da4ce7f270e7_de-DE&_t_hit.pos=4&_t_tags=andquerymatch%2clanguage%3ade%2csiteid%3a162d49d9-f0ac-4d2d-a110-e8143f6ca828&v=F23783%3a%3a7323450464196
Fit good for the first test. Arrived today from china ...
I think the naked looks and feels the best!!! Then why using covers, protectors, or else!!!
I use on all sides hydrogel. And works great... I drop it 4 times to all surfaces and still no scratch.
I'm not prone to dropping my phones or having butter fingers, however I don't want to chance it. So far I have purchased a Whitestone dome for the front (have not installed it yet), Samsung's aramid and leather cover (still waiting on my leather cover to arrive). The last phone I rocked without a case was my HD2? That thing is a tank!
No case ..
Only screen protector inside and outside
Sent from my SM-F916B using Tapatalk
My simple experience after around 2 months of use. I finally got the courage few days back to remove the inner screen. Knowing I prefer always my phone without a case and a protector.
The inner screen , without a doubt is way clearer and less smudgy without one and it is perfect.
Anyways, I have already bought 2 orotectors, both are somehow the sam price, however, one turned out to be excellent and as good as without protector and one is more smudgy than the original.
My recommendation for ones who doesn't want to keep inner screen without protection is to get the good one, you get the best of both words, clarity and protection.
I have the samsung aramid case since day one but I never used to be honest, only the first few days...
The good protector and the bad one in sequence:
https://www.amazon.ae/ccessory-Scre...+&sr=1-1-82924ca5-d5c8-45d1-a40c-360835499ae5
https://www.amazon.ae/FanTing-Samsu...+&sr=1-2-82924ca5-d5c8-45d1-a40c-360835499ae5
---------- Post added at 05:17 PM ---------- Previous post was at 05:14 PM ----------
I forgot to mention both came in a typical outside packaging to my surprise... I thought they are bluffing actually
I used matte black outside screen protector and Orzero inner screen protector which is night and day comparing to the stock plastic feel one. For case, I went with Spigen Slim case works well because I dropped the phone once and some minor scratches on the edges.
Amazon.com: (2 Sets) Orzero 2 Pack Soft Front Screen Protector and 2 Pack Inside Screen Protector Compatible for Samsung Galaxy Z Fold2 5G, High Definition Anti-Scratch Bubble-Free (Lifetime Replacement)
Amazon.com: (2 Sets) Orzero 2 Pack Soft Front Screen Protector and 2 Pack Inside Screen Protector Compatible for Samsung Galaxy Z Fold2 5G, High Definition Anti-Scratch Bubble-Free (Lifetime Replacement)
www.amazon.com
D.J.ChriZZ said:
Fit good for the first test. Arrived today from china ...
Click to expand...
Click to collapse
What case is this you're using? Looks good! Interested in buying one myself.
I just removed the inner (original) screen protector and installed matt hydropel screen protector. The original one is really just badly . I like the matt taste now on the inner screen and of course no fingerprints anymore...
I went ahead a few days ago and removed the inner and outer screen protectors. The inner was getting nastier looking with smudges plus I signed up for Samsung Care+ so if anything happens to the screen I only pay like $29 for a replacement.