Good morning everyone.
Today I tried to flash twrp.img from a laptop to my phone and I'm stuck on a black screen saying,
'USB transferring...
USB transmission OK Time:601ms Vel:24259KB/s'
I tried to manually power off my phone by using "Volume up+Volume down+Power" buttons simultaneously but it didn't work. Please suggest any ways that are useful in your regard.
Thank you.
Android version??
Related
I recently got a t989 with firmware UVMC6 preinstalled. And I can't get the phone to odin mode. I have tried all methods like inserting usb cable while holding volume up and down button, inserting usb cable while holding power and volume down button. But it always take me to recovery mode instead. I even tried to boot it through adb command prompt but the phone isn't recognized by adb. I have usb driver installed correctly. I have used different usb cables. Does anyone know if the lastested batch of T989s even have a download mode?
Thank you for your help?
twisteraml said:
I recently got a t989 with firmware UVMC6 preinstalled. And I can't get the phone to odin mode. I have tried all methods like inserting usb cable while holding volume up and down button, inserting usb cable while holding power and volume down button. But it always take me to recovery mode instead. I even tried to boot it through adb command prompt but the phone isn't recognized by adb. I have usb driver installed correctly. I have used different usb cables. Does anyone know if the lastested batch of T989s even have a download mode?
Thank you for your help?
Click to expand...
Click to collapse
Try holding just volume down instead of both... (telus/koodo phones use volume down only to get to download mode)
twisteraml said:
I recently got a t989 with firmware UVMC6 preinstalled. And I can't get the phone to odin mode. I have tried all methods like inserting usb cable while holding volume up and down button, inserting usb cable while holding power and volume down button. But it always take me to recovery mode instead. I even tried to boot it through adb command prompt but the phone isn't recognized by adb. I have usb driver installed correctly. I have used different usb cables. Does anyone know if the lastested batch of T989s even have a download mode?
Thank you for your help?
Click to expand...
Click to collapse
My replacement s2 was built in may and it had DL mode, try booting the phone just like u would to go into recovery but after the first vibration let go of power and vol- quick, should bring up a screen that says "installing custom firmware may cause blah blah blah" press vol+ to continue, that's how mine is anyway
Sent from my SGH-T989 using xda premium
Hi all. I´ve got this tablet: Arnova 10 G1 - rooted. I have a problem with booting. When it starts, it keeps rebooting on boot screen. I can´t go into the recovery mode :crying:. I've got these buttons: Volume Up ´, Volume Down, reset button and power button. I have 2 USB ports. One large and one small USB port (microUSB).When I connect to PC, It doesn t recognize it. ´ I had connected the two USB ports.I do not know what further. Thank you very much for your help.
hi,
any help is hugely appreciated.
I wiped my phone in recovery with the option to wipe for new custom rom, this worked fine. when i went to install custom rom it failed and then turned itself off. now the phone just gets stuck at the Sony logo. the only way i can turn it off is via the red button in the sim slot.
I am unable to connect to the computer at all, no fastboot. I'm also unable to boot into recovery to restore.
Please help. Hope i haven't ****ed it up beyond fixing
Thanks
Flash a stock ftf with flashtool (in flashmode). You should definitely get into flashmode and fastboot, otherwise there is a problem with your computer.
Funny, I didn't even know there was a red button Holding Volume Up + Power for a few seconds always worked for me, no matter in which state the phone was.
Hi all,
I've exactely the same problem !!!
My phone stuck to Sony logo, and not reconyze on my 3 PC.... before that, usb connexion work fine on all PC, but now.... nothing
I've just POWER + and VOL+ (its power off the phone), i've no led color light
I've try flashboot, but not detect my phone
i've try to install :
flashtool-0.9.16.1-windows (not detected)
Flashtool-drivers-1.5-20140318 (my computer doesnt not see my phone)
Xperia_Z1_Compact_driver (my computer doesnt not see my phone too)
I can't go into Flashmode...
When i power off my Z1c, and i plug usb + (vol+) nothing appear...stuck Sony logo...
I'm lost... I need your help XDA members ! just U can help me
PS : the red button is in the SIM slot, but i think is same POWER + (VOL+).... its power off the phone
Because you're doing it wrong. Vol+ enters fastboot mode, you have to press Vol- to enter flashmode. Then use Flashtool to restore the firmware.
Iruwen said:
Because you're doing it wrong. Vol+ enters fastboot mode, you have to press Vol- to enter flashmode. Then use Flashtool to restore the firmware.
Click to expand...
Click to collapse
THX for your response !
Sorry it's a mistake....
I've try both (vol+ and USB) and (vol- and USB).... but no sound (device not detected), in device manager nothing appear too.
I've make a fresh install of windows 7 x64 on another PC.
I finaly working to boot (2-3 times) with Vol- + USB cable, but stay in sony logo and Flashtool whait for device...
Please i need u're help beacause i'm really lost (usualy i flash many phone S4, Mediatek, phones, etc...) but now i dont find solution
My problem come from the original cable
All this because of the USB cable does not work ... CRAZY !
This USB cable is new and original sony... just 2 Weeks
I solved my problem with new one
That's unfortunate, good you found the issue.
Hello everyone, I got a problem again with my Robin, when I try to turn on the phone I do it with my charger since my power button and volume buttons are smashed, now since I cant use my power button I cant start the phone, and after a while it boots me intro TWRP, so my question is Is there a way to turn on my Robin without my power button on TWRP?
Your help is very aprecciated. :fingers-crossed:
I would think mounting it to a pc and issuing a reboot command would work. I never thought TWRP loaded automatically though.
philhachey said:
I would think mounting it to a pc and issuing a reboot command would work. I never thought TWRP loaded automatically though.
Click to expand...
Click to collapse
I already did that, and it didn't work :crying: it goes to fastboot mode, I cant choose anything and just stays in fastboot for a while then it goes back to TWRP.
Maybe your smashed buttons are getting pressed at boot simulating the fastboot and/or recovery.
Today I Bricked My LG820Qm
I was updating my Lg g8 using LG UP, When the Process on 64% my PC power off
After that my phone stuck in Qualcomm HS-USM QDLoader 9008
Any solution to come out from this mode to Downloaded Mode so that i can update using LG up.
I was updating G820QM10i_00_NAO_US_OP_0401 to G820QM20b_00_NAO_US_OP_1224
My LG up LGUP_Lab_Frame_Ver_1_16_0_3
Can you try to switch to download mode by press&hold VOL+ while inserting the USB cable (connected to PC). Phone needs to be off while doing so.
tron1 said:
Can you try to switch to download mode by press&hold VOL+ while inserting the USB cable (connected to PC). Phone needs to be off while doing so.
Click to expand...
Click to collapse
I tried not working
If i press&hold VOL+ while inserting the USB cable still my phone come with Qualcomm HS-USB Mode
thanks for your reply
What happens if you press&hold VOL- (furing the whole procedure) push the power button until the phone vibrates, release the button und press&hold the power button?
tron1 said:
What happens if you press&hold VOL- (furing the whole procedure) push the power button until the phone vibrates, release the button und press&hold the power button?
Click to expand...
Click to collapse
Which ever combination, Vol- + power phone power of
with in sec it boot to Qualcomm mode
I don't know where to ask so I'm gonna try here. My G820N is stuck on Android 10 beta. Whenever I flash an official kdz, it only allows for emergency calls. Can't do anything. Any help would be appreciated
Following, in right here with ya.
atsuisofu said:
Following, in right here with ya.
Click to expand...
Click to collapse
Try entering download mode with phone disconnected from USB cable.
Also try to see if it gets recognized by LG-UP or by LG Bridge. These 2 softwares don't need download mode to be able to flash, just the phone to be recognized on some PORT.
Try also factory reset hard menu. Also try switching between Slot A and Slot B. There is also this backup method. Phone is not dead on one of those slots.
If nothing works (but slot a slot b should 100% work) , wait for the firehose, it's just around the corner. That will restore the phone back 100%.
For more info search v50thinq on telegram app. :good:
I can t get to download as it freezes and without the USB cable it doesn't even try and enter. I appreciate the recommendations. I was thinking of the a/b seit hbut without the use of fastboot I am at a loss of how to switch between the two as I thought the system chose and the switch happened upon rebooting once a system had been selected ie as in turning the unit off after loading the os set a flag to go to the opposite system upon completing the inftframs and boot sequence.
vikramanananda said:
Which ever combination, Vol- + power phone power of
with in sec it boot to Qualcomm mode
Click to expand...
Click to collapse
Hi, i'm facing the same problem today, my QM will not go into any mode other than the Qualcomm mode. Were you able to recover your phone finally ?
vikramanananda said:
Which ever combination, Vol- + power phone power of
with in sec it boot to Qualcomm mode
Click to expand...
Click to collapse
did you ever get it fixed. im having the same problem.
johnnycm77 said:
did you ever get it fixed. im having the same problem.
Click to expand...
Click to collapse
me too, do you fix it?
vikramanananda said:
Today I Bricked My LG820Qm
I was updating my Lg g8 using LG UP, When the Process on 64% my PC power off
After that my phone stuck in Qualcomm HS-USM QDLoader 9008
Any solution to come out from this mode to Downloaded Mode so that i can update using LG up.
I was updating G820QM10i_00_NAO_US_OP_0401 to G820QM20b_00_NAO_US_OP_1224
My LG up LGUP_Lab_Frame_Ver_1_16_0_3
Click to expand...
Click to collapse
So, if the device, as you say, lost power during an update like that, then almost assuredly you have at least one, if not numerous corrupted partitions.
And, it's specific partitions on the device that allow it to enter download mode. One of these most know about or have heard of is the laf partition. But other have to be there also for it to work, I don't remember exactly what the others off the top of my head, but that info is easily found.
The key thing you need (or any others commenting same prob), is to be able to enter EDL mode and have qfil installed and recognizing the device. If you can get that far, it would be easy to find the correct partitions you could flash with qfil and then immediately go from qfil to download mode.
Many many people have done this. Just get qfil set up (see guides section) and get the device recognized. that takes some effort but it's def doable.