Related
OK, so I dropped my phone and the LCD went out, I hooked the phone up to the laptop and the phone still works fine, even the touch screen works. ( I used My MObiler to see phone screen on the pc).
I bought a new LCD screen off of Ebay and replace it, now, the LCD screen works, but for some reason, the touch screen stopped working.
When I took the LCD apart from the touch screen, there seem to be a layer of grease of some sort between the touch screen and the LCD. I wiped it off with a lens cloth, don't know if that caused any problem.
Also there is a dark film (tinted) glued to the touch screen when looking from the back, what is that for? I looked at replacement touch screen on Ebay but none of them have the tinted film layer. I've search all over the internet for instructions but can't find any.
So my question is, what are the correct procedures for replacing the LCD screen and the touch screen (digitizer) ? Also after I installed the new LCD screen, the screen is very reflective and the glare is really bad, how do I fix that problem?
Thank you experts!!
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
bojangle said:
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
Click to expand...
Click to collapse
I went ahead and purchased the digitizer by itself after the original stopped working. Hopefully, it will get my phone back to normal. Thanks for your reply!
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
fone_fanatic said:
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
Click to expand...
Click to collapse
I should have ordered the kit instead of just the LCD. What lead me to order just the LCD is when I hooked the phone to my pc and confirmedthe digitizer still worked. And since this is the first time ever I disassemble a phone, I assumed the two things were separated.
But my digitizer should come in tomorrow so I'll just have to wait and see. Thanks for the info.
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone pad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing my in the car door as I got in....it feel out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone bad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
Click to expand...
Click to collapse
Here's a photo guide of the disassembly of a Rhodium (TP2), it might give you some insight. There's also been a number of threads in this section about hardware parts and the screen/digitizer in particular, listing places where people found/ordered replacement parts.
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
Click to expand...
Click to collapse
The disassembly instructions are here: http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
I did not follow those instructions since I did not want to open the back of the phone.
What i did was I tilted up the phone and used a very small screwdriver and unscrewed the two screws from an angle (it worked).
Then I pried the back of the tilting part of the phone all around to reveal the inside. Be careful not to pull too hard on the flat cable since it's still attached to the back (body) of the phone.
The LCD and touch screen are glued together (I didn't know that before). At this point I would remove the tape that is attaching the flat cable to the back of the LCD, and also lift up the clear yellow tape and detach the three connections.
The widest ribbon is from the LCD, the medium one is for the 4 hard buttons in the front, and the little one is for the touch screen.
I would suggest wearing some sort of anti-static wrist strap (I think I fried my touch screen along with the flat ribbon that is attached to the phone while trying to replace the LCD without anti-static wrist strap).
Once the whole tilting part is freed from the phone, I would carefully push the whole screen (digitizer + lcd) out from the frame, again, they are glued to the frame but can be removed fairly easy.
That's it, the install is reversed of removal and hopefully yours will work again.
Like I said, I think I fried my flat ribbon so after replacing the Digitizer (it came in today), the touch screen still doesn't work, so now I'm looking for that part, I'd appreciate a link to it if anybody knows where to get one.
Oh, and for the parts, just do a search on ebay for "touch pro 2 lcd" or touch pro 2 lcd + digitizer"
Gook luck with your phone!
What tape to use to stick digitizer back to inner bezel/chassis?
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
zedii.co.uk/DSC_0002.JPG
^some of that tape is left on the digitizer... it's the black spongy stuff...
zedii.co.uk/DSC_0003.JPG
^i cleaned (removed residue of sticky tape) in the inner part of the bezel where the digitizer would stick...
Any specific tape to use that anyone knows of?
zedii said:
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
Any specific tape to use that anyone knows of?
Click to expand...
Click to collapse
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
adp9626 said:
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
Click to expand...
Click to collapse
Thanks for the advice adp9626! Well in summary I think I've just been messing about too much and being stupid really.
In the end, I managed to just remove the top part of the screen without actually having to break into the bottom section of the phone.
I was a bit concerned about the whole sticking of the LCD to the Digitizer part. I actually did purchase them separately, however I was not sure what kind of glue was used to stick them both together - as I recall it was a nightmare to try and remove the LCD off the old Digitizer.
So I returned both separate parts (got a full refund as I didn't use them) - and now I am looking to purchase both parts stuck together.
I'm waiting on the guy on eBay to confirm that they are both stuck together. I'm also thinking of using double sided sticky tape to stick the Digitizer back to the inner bezel...
So that's the final plan! I've been a bit silly in rushing with ordering parts etc. but I just want to be on the safe side now - well - at least with the LCD stuck to the Digitizer part.
I will take your advice on the gel superglue if the double sided sticky tape doesn't prove it's stickyness!
Thanks
Zayd.
Can anyone help me find the lcd screen and digitizer as a single unit for Sprint? Everyone I find states not for CDMA.
Thanks
Anyone ??? I spent an hour on google and still came up with no leads.
hyghlndr said:
Anyone ??? I spent an hour on google and still came up with no leads.
Click to expand...
Click to collapse
I ordered one from this guy and it works great. it comes with the entire top half of the phone and the keyboard. There is only one left so you may want to hurry. Link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=270583335455&Category=20336&_trkparms=algo%3DLVI%26its%3DI%26otn%3D2
Edit: I wanted to add that they're are slightly used so there will be scratches. The one i received is a little more scratched than my original then again the scratches aren't noticeable when the back light is on and you're getting a working screen.
Just my experience, I had a faulty LCD, digitizer was OK. Bought a replacement LCD off ebay, delivered from China but only cost me £20 inc delivery. Arrived with tools as well (T5, T6, philiips, and pry tool). Followed a couple of disassembly instructions online, took me a while to get all apart but managed it. None of the instructions online go through actually taking the screen out, I thought I'd messed it up as I took the back half of the LCD off and left the front bit on, and I couldnt get it off at first. I ended up using a very sharp scalpel to slide between the LCD and digitizer and got them apart eventually, as I didnt realise that they were glued.
Anyway, I just placed the screen on, no glue as there is a ring of sticky tape around the back of the digitizer which holds the screen in. Connected everything back in the end and its working fine. Only prob is I think I damaged the power/standby button, so be careful when around this area.
Touch Screen not responding after replacement
Recently, I replaced a glass screen on a SGH-M919 Galaxy S4. Previously, during the process of cleaning the glue residues off the LCD screen; I rubbed it with rubbing alcohol and it removed a small streak of the adhesive glue off left side of LCD screen and bottom right corner. After installed the new glass screen, I noticed a few spots of the glass screen wasn't sticking onto the sticky layer. So it looked like it has big air bubble between the glass screen and LCD. And I could see the rubbed off streak on the LCD screen. Everything worked fine with the new glass screen, with the exception of seeing the streak and bottom right corner rubbed off.
A few days ago, I had a table clock fell on top of the phone and broke a piece of glass. Nothing happened to the LCD screen and still functional 100%. So I got a replacement glass screen - the same as the first time replacement. With noticing of the rubbed off streak and corner of the adhesive layer on the LCD screen - I decided to rub off all of the adhesive layer from the LCD. I sprayed some Goof Off liquid on the adhesive layer and left it over night. Next morning I continued scraping off the glue with a small plastic card. Cleaned off all glue residues and examined the LCD screen for any scratches or damage. There was none. Re-installed new glass screen - but now the touch screen does not respond to the touching on the icons. Only the Home, Menu & Back touch button work. I was baffled after this.
Could it be that because I left some the Goof Off liquid on top of the LCD screen over night and it might have leaked to the other side and shorted out something? I saw a few forums that suggested a Factory Reset. I did that - but still didn't work. Please advise on what I need to do to fix this problem.
Thank you in advance for the advise or suggestion.
So you know that these are the TP2 forums, and no one has used this thread in the last 3 years....right?
LCD digitizer replacement.. now black screen
I saw the for replacing the LCD-digitizer of my nexus 4 phone, and followed the steps carefully. After I placed the battery, I checked to see if the phone turns ON and the display is working before I complete the last step of putting the back coverplate. I successfully switched it ON, saw a perfectly working screen, and browsed through my apps. To complete the assembly, I put the back cover by gently pressing the frame along the edges, but suddenly I saw some yellow green lines in the middle of the screen. I switched it off and again switched in ON, but now the entire screen had light with no display.
To fix this, I tried again checking all connections but no luck. What could be the reason for the sudden loss of display when it worked perfectly fine moments ago? Is there a possibility that I damaged the LCD while putting the back cover on the phone?
I am also not sure about one of the ribbon connectors of the digitizer. There are 2 big ones which are prominent and has ports to connect. However, there is a little third one which also has to come through the gap but doesn’t connect anywhere. Has anyone also experienced this while replacing the screen? Any help will be appreciated.
My little cousin have EVO with shattered screen, and I am trying to get him replacement part. Screen has couple cracks but if fully functional so I am thinking which of following I should get...
http://www.ebay.com/itm/OEM-HTC-Evo...939?pt=LH_DefaultDomain_0&hash=item4aa37ae05b
http://www.ebay.com/itm/LCD-Screen-...607?pt=LH_DefaultDomain_0&hash=item35b6c5d6e7
http://www.ebay.com/itm/New-OEM-HTC...536?pt=LH_DefaultDomain_0&hash=item2a158d59d0
What is difference beside price ? Looks like cheep one is just outside glass and other two might have full screen ?
Now back to phone... Outside layer of glas is cracked but is there anything damaged inside I have no idea (i doubt any damage is there since screen fully operative). What do you guys thing? I can upload some pictures tonight around 6 (Central time).
From experience here is what I will tell you. The easiest thing to do is to replace the entire front housing. The front glass can be replaced but you risk breaking the lcd underneath. You can get the front piece of glass off by either taking a razor and cutting it from the adhesive or taking a heat gun (or hair drier will work) and heating it until the adhesive losens enough to pull the glass off. The problem with replacing the front housing is you need to know if it is a wide cable or small cable. The only way to know this for sure is to open the phone and look at the bottom ribbon of the left side of the board, this is the lcd ribbon and that will tell you if it needs to be big or little. Some people will tell you that you can look at the letters on the bottom right of the sticker where the esn is (they will be like a, b, c, xa, etc.) but this does not always work. I fix these everyday and have seen all boards with both types of screens. Hope this helps.
I've had my Note 10. 1 since July of this year, so about 5 months now. I more or less keep the tablet in a leather case most of the time and there were no major issues unril just recently. I had noticed earlier today that there seemed to be rows of little dots along the bottom of my screen, right above the buttons. These dots look like it could be drops from either water or glue or something of the sort.
I tried scratching it off with my fingernail but then found out it wasnt on the top of the screen but under it. It doesnt seem to effect the touchscreen but thid could become a future problem. Picture will be attached (though it could be hard to see)
Thank you in advance :good:
Air bubbles in the glue holding the LCD display & digitizer together. Never heard of them being an issue aside from being a small cosmetic eyesore.
I have the same bubbles except they started to spread. I also bought mine at the end of June. I am asking Samsung to repair it.
Sent from my SM-P600 using XDA Free mobile app
Hi everyone. I have learned a lot from the forums over the years and have been on here since my very first android device (by way of introduction, I don't think I have ever posted). I did use the search and found threads talking about replacing broken screens on the 10.1 2014 but none addressed my actual question.
I found my device with a hairline crack in the lower portion of the screen, running from just to the right of the back button to about an inch and a half to two inches up the right side of the device. I have seen that the screen is glued on the edges and that the digitizer is not completely glued to the LCD. However, I have too much dust and cat hair and stuff around to be sure of getting a completely clean replacement job done.
Since the crack seems to be complete, edge to edge, and I do have the tablet in an otterbox case to reduce flexing, should it be fine for use until the price of the LCD/Glass combo comes down in price? So far, running my finger and stylus over the area there seems to be no reduction in function, and the LCD underneath is completely intact. I have a screen protector over the screen, so I cannot even feel the crack. (In case anyone was curious how it happened in an otterbox, I was overconfident and threw it into my purse without the screen shield on it, and something in my purse pressed on the edge of the screen)
I saw a lot of talk about replacing the screen, but no comments on anyone continuing to use the device with a crack in it. Thanks for reading, I know I can be long winded.
@noxdrako I don't see why not. Majority of the time when a display cracks its only the outer parts and internel parts remain untouched. My brother has been using his cracked Blackberry tablet for ages and I have a friend who has been using his S3 which has a hairline crack along the screen for well over a year with no issues.
Sent via Note 10.1 2014 Edition on Tapatalk
Thanks for the reply. I have been using it with some tlc till i can afford to have it repaired. After I repair i am thinking of putting a tempered glass protector on it.
The GPEL screen protector is fantastic! No dot matrix, full adhesive, comes with 2, affordable, case friendly & no Halo affect.
The black border is just a tad too big, so you lose a row of pixels..
https://www.amazon.com/dp/B07D1CG8QY/ref=cm_sw_r_cp_apa_MQYCBbYM79AP7
Thanks for sharing the review!
Hello,
Does the black line cut from the sides of the screen ? Or the bottom ?
Thank you !
Al3xxxinho said:
Hello,
Does the black line cut from the sides of the screen ? Or the bottom ?
Thank you !
Click to expand...
Click to collapse
I currently have this protector, as stated in the OP it cuts off a little on all sides and is it a bit crooked. I have plans to review another screen protector (might be the one) in a new thread soon
So, anyone that sells this internationally for less than 15usd for shipping?
8bitbang said:
I currently have this protector, as stated in the OP it cuts off a little on all sides and is it a bit crooked. I have plans to review another screen protector (might be the one) in a new thread soon
Click to expand...
Click to collapse
Care to share which one? I just picked up a g7 yesterday, have a SUPCASE UB Pro on order, want to pull the included plastic shield, put on glass.
The gpel sounds good, but I'm interested in seeing what else looks solid. (Not interested in going to the $50 dome glass.)
Sent from my LM-G710VM using Tapatalk
markfm said:
Care to share which one? I just picked up a g7 yesterday, have a SUPCASE UB Pro on order, want to pull the included plastic shield, put on glass.
The gpel sounds good, but I'm interested in seeing what else looks solid. (Not interested in going to the $50 dome glass.)
Click to expand...
Click to collapse
I have 2 g7s one with gpel and dome glass. Do you want a side by side comparsion picture. Either is perfect and has flaws
8bitbang said:
I have 2 g7s one with gpel and dome glass. Do you want a side by side comparsion picture. Either is perfect and has flaws
Click to expand...
Click to collapse
Sure, thanks!
Sent from my LM-G710VM using Tapatalk
Dome is on the left and GPEL is on the right
Dome - doesn't affect the sensors but it's smaller than the actual display. It's a bit too short on the left and right sides. This causes light bleed on the edge of the screen protector. Dust magnet but less likely to have bubbles
GPEL - affects sensors and black borders cut off display and is especially noticeable when watching YouTube videos in full screen pinch. Bubbles can happen
8bitbang said:
Dome is on the left and GPEL is on the right
Dome - doesn't affect the sensors but it's smaller than the actual display. It's a bit too short on the left and right sides. This causes light bleed on the edge of the screen protector. Dust magnet but less likely to have bubbles
GPEL - affects sensors and black borders cut off display and is especially noticeable when watching YouTube videos in full screen pinch. Bubbles can happen
Click to expand...
Click to collapse
What are the sensor impacts from using the gpel?
Sent from my LM-G710VM using Tapatalk
markfm said:
What are the sensor impacts from using the gpel?
Click to expand...
Click to collapse
It can cause the display to dim and sometimes turn off like when you raise your phone to answer a call. To be fair all full cover screen protectors are suffering for this flaw. Even OtterBox is getting massive hate for their version and is temporary unavailable.
Just to let you guys know,
You will NOT have the "notch" border pixel line problem if you perfectly align the holes at the top with the sensors, but with a catch: you have to align it with the sensor being more towards the bottom than dead center. My very first screen protector had it more towards the top (basically, the entire protector aligned downwards 1mm, which made the notch very prominent). Then I wasted two more trying to make it bottom aligned. (edit). That fixes the sensor problem and the pixel problem at the top with the notch, unless you are looking down at the phone from above the phone (and who the hell does that?). Unfortunately, perfect alignment is expensive and will cost you several screen protectors since you have to deal with lifting and replanting as well as small nudging WHILE you are in a steamy bathroom hoping for no dust hairs to drop on something. Took me three of them to get it perfect. But I got perfect and I'm pleased.
The left and right sides black bars aren't a problem; the missing pixel line can always be seen by looking to the side of the phone. Just remember to focus on aligning the TOP first (edit) align the ridged sensor so it's almost touching the bottom cutout) and then pressing the top down, then the middle. That's the hard part. This will also cause a few air bubbles on the sides, which means you will have to carefully lift the edges and press outwards to reapply again, and make very sure your fingernails are spotless. That is going to be the risk of dust getting in there, so be careful. Get it perfect then everything will make you happy.
The results are worth it.
Falkentyne said:
Just to let you guys know,
You will NOT have the "notch" border pixel line problem if you perfectly align the holes at the top with the sensors. That fixes the sensor problem and the pixel problem at the top with the notch, unless you are looking down at the phone from above the phone (and who the hell does that?). Unfortunately, perfect alignment is expensive and will cost you several screen protectors since you have to deal with lifting and replanting as well as small nudging WHILE you are in a steamy bathroom hoping for no dust hairs to drop on something. Took me three of them to get it perfect. But I got perfect and I'm pleased.
The left and right sides black bars aren't a problem; the missing pixel line can always be seen by looking to the side of the phone. Just remember to focus on aligning the TOP first and then pressing the top down, then the middle. That's the hard part. This will also cause a few air bubbles on the sides, which means you will have to carefully lift the edges and press outwards to reapply again, and make very sure your fingernails are spotless. That is going to be the risk of dust getting in there, so be careful. Get it perfect then everything will make you happy.
The results are worth it.
Click to expand...
Click to collapse
Where's your proof? Both the OP and me have reported information (with evidence mind you) that contradicts your statements.
8bitbang said:
Where's your proof? Both the OP and me have reported information (with evidence mind you) that contradicts your statements.
Click to expand...
Click to collapse
My proof is me owning the phone and going through 4 GPEL screen protectors before I got it perfect. I paid my dues. And as someone disabled and on SSI and with a fixed income, I don't have money to go through infinite screen protectors, unlike some of you people here.
The trick is to align the "ridged" sensor so that it's (edit: just looked at my phone: the hole aligned at the -bottom- of the ridged sensor, rather than dead center! but not blocked by the edge of the screen protector), sensor bottom aligned and then after that, making sure all the sides are perfectly straight when applying (a LOT harder than you think, even in a steamy shower, because I'm in an old apartment). Took me 4 protectors and cost me over $30 dollars. (air bubbles and dust from me constantly having to re-lift to get the orientation perfect and eventually dust getting under the edges, and I have OCD so I want nothing less than perfection). Might even give GPEL an email and see if they'll send me an extra sample for my troubles. And no, I have no way to take a picture of the phone screen for you.
I forgot that I had it 'bottom' side sensor aligned rather than mid sensor aligned because I spent over 30 minutes in the shower sweating and uncomfortable wasting screen protectors trying to get rid of the notch line and getting it on with air bubbles. I was extremely stressed out, and it's difficult for someone with a metal bar in their spine to have to work that hard. Needless to say the fourth protector (thank god) I got absolutely perfect.
If it's dead center yes you will have a pixel row of the notch visible. So you have to 'raise' the protector upwards by that same pixel space. There's enough cutout to work with to make that work.
This is no problem because the very *BOTTOM* of the phone isn't used by the display (since this is an IPS display; someone mentioned this in a review, compared to OLED), unlike the top, so you have like 1mm of extra room to work with for the cutout (as long as the top sensor isn't blocked by the bottom edge of the protector). The black border at the bottom won't interfere with anything (checked with a screen test in the service menu).
I'll -try- to upload a picture of the phone with my laptop's built in camera if I can later on, but please don't be upset if you don't like the quality. My laptop isn't high definition and isn't made for such precise pictures. 720p isn't going to work very well.
@Falkentyne - thanks for the explanation.
It sounds like the critical part is where the protector is relative to the front mounted speaker (towards the right edge of the notch) front mounted camera (center of the notch), mystery circle to the left of the camera, and tiny notification led circle furthest to the left side of the notch?
If a photo of your own screen is hard to get, I've attached a photo, the top part of the g7 screen. Maybe draw a line showing where the gpel edge needs to be (outside edge of the line = outside edge of the gpel).
This is the best I could do.
markfm said:
@Falkentyne - thanks for the explanation.
It sounds like the critical part is where the protector is relative to the front mounted speaker (towards the right edge of the notch) front mounted camera (center of the notch), mystery circle to the left of the camera, and tiny notification led circle furthest to the left side of the notch?
If a photo of your own screen is hard to get, I've attached a photo, the top part of the g7 screen. Maybe draw a line showing where the gpel edge needs to be (outside edge of the line = outside edge of the gpel).
Click to expand...
Click to collapse
In your picture, move the screen protector UP about 1mm upwards so the bottom is where the red line is.
This will leave about 1mm of 'extra' space above the sensor area (whatever that thing is, sensor, microphone, I don't know). But it will still fit fully into the enclosure.
Took me 4 screen protectors to do this AND have no spare dust hairs from all the relifting !
Perfect thanks!
Just over the bottom edge of the front speaker (the oval on the right with the grid pattern).
I just got my gpel protectors in today, will give it a try tomorrow.
I installed it following your suggestion, it seems to be working fine. Thanks for the info!
markfm said:
I installed it following your suggestion, it seems to be working fine. Thanks for the info!
Click to expand...
Click to collapse
Glad you got it working and got the results you wanted.
It's good that the cutout is slightly larger than the speaker(and sensor/camera) itself, but bad that people won't know about this without experimentation (or somehow coming across the posts here).