Develop Bugs

[Q] N7100 International Version - Only Download Mode / White Screen grey Stripes

Hello,
I have a N7100 that cam to me stuck at boot logo.
I flashed it with this firmware : N7100XXUENA1_OLBEML1 ( Re-Partition UNCHECKED)
the phone came back alive but with genereic imei (0049) then i flashed philz_touch_5.11.2-n7100.tar
did a wipe + factory reset then clean to install a ROM , then flashed this rom : PhoeniX.ROM.V12.XXDME6.N7100.by.tamirda ( didn't choose any tweak in Aroma)
phone stuck at phoenix boot logo so i used this Android_Revolution_HD_Super_Wipe_Note_2 then reflashed following the instructions in the thread, no success ( basically i wanted to get this modem : XXDME4 and i tought flashing it by the phoenix installer would be safer )
laid my hand on Z3X box then reflashed the stock firmware through it( N7100XXUENA1_OLBEML1) , did an efs backup there also and i saw the option to repair IMEI.
tried it, it asked for Root access. then I reflashed the custom recovery PhoeniX.ROM.V12.XXDME6.N7100.by.tamirda, after i used DrKetan_MultiTool_AdvanceV6.
the phone restarted with white screen and grey stripes.
I then decided to go back into recovery : no way , same white screen and grey stripes
tried to enter download mode : OK
I tought this is SDS but the screen showed this in download mode :
PRODUCT NAME : GT-N7100
CUSTOM BINARY DOWNLOAD : No
Current Binary : Samsung Official
System Status : Custom
Knox Warranty void : 0
AP SWREV :
as i see that PRODUCT NAME is not empty , i guessed that i would be able to flash it with Odin.
I used ODin 3.07, 3.09 but still the same result :
<ID:0/030> Get PIT for mapping..
<ID:0/030>
<ID:0/030> There is no PIT partition.
Unistalled Kies then downloaded these drivers : http://forum.xda-developers.com/showthread.php?t=961956 ( rebooted as instructed )
Tried again, same results.
Changed cables and USB ports, tried differents roms, tried to flash recovery only, kernels, still same results
and i still see the same informations on Download Mode screen.
This is my problem. i tried to give detailed informations in case someone might be able to find where i made a mistake and how to fix it.
Whatever might help is welcome. I am a software engineer and i have a little experience with ADB and FastBoot commands and programming languages so don't feel restricted to give me even complicated procedure, i have the patience to follow them and i am more than eager to learn.
Thank you and i hope i didn't break any rules.
Salaam

Encountering the same issue with you except on a N7105.

Device N5100 stuck at logo with complication

Hi all
I own this magical and wonderful device, Italian version *lol*
after a wipe mistake I am found at this situation:
1. Device can't boot normally. TWRP says "No OS Installed! Are you sure you wish to reboot?"
2. TWRP works properly. I have flashed the recovery as suggested in this thread but I would need a factory stock image.
3. Odin don't see my device for some reason so I can't use it
My idea is that somehow I managed to wipe the OS and now I am faced with three mithycal questions questions:
1. How to solve this issue? I searched the forum for my model stock factory image but no luck.
2. Can I install a random ROM from inside TWRP somehow via the install menu? I did that with the recovery image but it still says there is no OS
3. Last but not least: will I be able unroot it and then with the Triangle system get it back to shape and send it to samsung? I had a little bit of a problem - that is the reason i tried the wipe in the frist place - with the 3g connection not working anymore.
Thank you in advance for your help
:3

Note SM-N930F boot loop Hydrarom

Hi All,
Sorry for my English, it's not my language.
I need your help because I think I have bricked my Note 7 after trying to install the last Hydra rom 1.3.5.
I explain you the situation:
I have installed custom TWRP => it was good
Then I have rooted with superU => it was good
Then I have tried to install hydra rom => the installation was OK
The phone reboot at the end of installation => phone stay on start screen "Hydra rom" and reboot (loop infinite)
I cannot power OFF the phone.
I cannot go to the recovery menu.
I can only go to the download mode.
So I have tried to re-install TWRP with ODIN but it was not working. Ondin detects my phone and when I click on start, I have the message "Fail" on ODIN and the phone reboot.
Do you have any ideas to help me?
Thanks.

Note 7 Problem - please help if you can, please
Hello
I am newbie here with no proper experience [ I flashed mobile with success once but it was years ago with NOKIA e90!]
I have Note 7 exynos UK VODAFONE and I did flashed it with older OEM firmware [ to bring it back to 100% battery], I downloaded from sammobile than recent one on my mobile [ limited 60% battery]
I unchecked re-partition
I used AP file there
all went fine with ODIN v3.11.1 all pass !
but once mobile started I have big message on my screen which does not disappear [ see attached photo]
unfortunately, the process
com.android.phone stopped
I can click/press OK on screen below that message, but it reappears again and again
I tried to flash it again but now ODIN says fail and something about PIT
I would appreciate some help or tell me what steps I should take [ apart of surrendering phone to place I bought it from!!!]
regards
M.

What I did to make this work:
1 install TWRP
2 whipe format data "yes" x3
3 advanced format everything except external storage
4 reboot to download mode
5 open Odin on pc flash BL/CP provided in original Post of HydraRom
6 install HydraRom via TWRP
7 follow direction installation process
8 wait 5 mins boom!
Never fails for me.

I did that. I have already did that several time before. But I think I have understood the problem. My BL file is corrupt (may be during the download from the server)!
So I think the boot loader not working correctly! I have tried to reload one but without success. Directly Odin write "FAIL"...

Able to access Download mode only after Hydra flash. Solution?
Did this issue ever get a solution? I am having the same issue. I can enter into download mode only after the attempted hydra flash. Now it's stuck on "Hydra N7" boot screen. I had N930F flashed and running with twrp. When I attempted hydra I believe that the full rom did not flash, only 40 MB or so. To make matters worse I can't find where I jotted down my baseband, etc. It was originally N930X (live demo model). Now I get fails in odin. What can I do to remedy my situation. I read that I should flash BPH6 base files, but here it says AGO or AG2 BL. Which is it? How do I wipe the cache and data since I can only access Odin mode? I believe my BL is corrupted. Please help. I was going to trade my Note 7 in but my imei is all zeros and the boot loop. I'm not sure that they will refund or exchange in this condition. Although, they should since I doubt Samsung wants the liability of having these devices out there. Any thoughts on the matter?
Any insight and guidance is greatly appreciated!
Grace Downed in Denver

https://forum.xda-developers.com/note-7/help/note-7-error-t3562629
i have the same issue.. hoping someone would help us.

Tab 3 10.1 GT-P5210 Soft-Brick: accidentally Re-Partition + Nand Erase in Odin

Hi Guys, please help if you can.
My sisters Samsung Tab 3 10.1 GT-P5210 was running very slow so I offered to factory reset it. I wanted to have a very clean install and since I have experience with rooting and installing custom roms on various phones and tablets in the past I didn’t consult any guides.
I used Odin3 version 3.12.7 (latest I could find) and downloaded the latest UK factory image P5210XXUBOB1_P5210BTUBOC1_BTU.zip from Sammobile and proceeded to flash the image.
Unfortunately in the Odin3 ‘Options’ tab I selected-
[x] Nand Erase
[x] Re-Partition
Already selected-
[x] Auto Reboot
[x] F. Reset Time
As I mentioned I was after a clean install of the factory rom and didn’t want any of the previous data left of the tablet.
The flash process completed successfully, the tablet rebooted and after the ‘Samsung Galaxy Tab 3’ logo passed the tablet displayed the glowing ‘Samsung’ text logo for over 30minutes
I know the first boot after a flash normally takes a while but it was clear before too long that something was wrong. After doing a bit of research I now know my mistake (shouldn’t have selected Re-Partition) but don’t know how to recover from it.
I’ve tried searching for ‘GT-P5210 Boot Loop Soft-Brick’ but have come across noting useful.
As I can get into download mode I’ve tried flashing-
twrp-2.8.6.0-p5210-v2.tar.md5 and
twrp-3.0.2-0-santos10wifi.tar.md5
and after each TWRP Recovery flash- which seem to complete successfully (I have Auto Reboot unselected in Odin3). I hold the Power + Volume+ buttons to try to get into recover but recovery doesn’t seem to be working.
Any help will be greatly appreciated.

Logoona said:
Hi Guys, please help if you can.
My sisters Samsung Tab 3 10.1 GT-P5210 was running very slow so I offered to factory reset it. I wanted to have a very clean install and since I have experience with rooting and installing custom roms on various phones and tablets in the past I didn’t consult any guides.
I used Odin3 version 3.12.7 (latest I could find) and downloaded the latest UK factory image P5210XXUBOB1_P5210BTUBOC1_BTU.zip from Sammobile and proceeded to flash the image.
Unfortunately in the Odin3 ‘Options’ tab I selected-
[x] Nand Erase
[x] Re-Partition
Already selected-
[x] Auto Reboot
[x] F. Reset Time
As I mentioned I was after a clean install of the factory rom and didn’t want any of the previous data left of the tablet.
The flash process completed successfully, the tablet rebooted and after the ‘Samsung Galaxy Tab 3’ logo passed the tablet displayed the glowing ‘Samsung’ text logo for over 30minutes
I know the first boot after a flash normally takes a while but it was clear before too long that something was wrong. After doing a bit of research I now know my mistake (shouldn’t have selected Re-Partition) but don’t know how to recover from it.
I’ve tried searching for ‘GT-P5210 Boot Loop Soft-Brick’ but have come across noting useful.
As I can get into download mode I’ve tried flashing-
twrp-2.8.6.0-p5210-v2.tar.md5 and
twrp-3.0.2-0-santos10wifi.tar.md5
and after each TWRP Recovery flash- which seem to complete successfully (I have Auto Reboot unselected in Odin3). I hold the Power + Volume+ buttons to try to get into recover but recovery doesn’t seem to be working.
Any help will be greatly appreciated.
Click to expand...
Click to collapse
It would be worth trying to find a pit file to flash along with your stock firmware again that way any partitions can be restored and firmware flashed correctly. When you find the pit files, make sure you only select Auto Reboot, Re-Partition and F.Reset Time

SM-T830 - Bootloop after flashing stock firmware

Hi all,
My tab S4 is stuck in this constant bootloop where it boot into the recovery for a split second and then it restarts. I've flashed it several times with different firmwares (T830XXU4BSI2, T830XXU4BSJ6) but I still get the same issue.
Tried flashing with Nand erase, Repartition checked, even tried flashing the combination rom but still get the same issue. I'm running out of options at this point and would appreciate if someone can point me in the right direction to resolve this.
Thanks in advance,

ice10311 said:
Hi all,
My tab S4 is stuck in this constant bootloop where it boot into the recovery for a split second and then it restarts. I've flashed it several times with different firmwares (T830XXU4BSI2, T830XXU4BSJ6) but I still get the same issue.
Tried flashing with Nand erase, Repartition checked, even tried flashing the combination rom but still get the same issue. I'm running out of options at this point and would appreciate if someone can point me in the right direction to resolve this.
Thanks in advance,
Click to expand...
Click to collapse
__Before all that, it was definitely needed a Nandroid Backup....Νow the situation is difficult & more complicated without backup.Anyway....
__We never delete the NAND file-Flash memory ! Normally,we dont check "Re-Partition" in Odin...We leave everything in "default mode" for flashing with odin !
"When you erase NAND on a samsung device, you wipe everything including, boot- kernel- recovery- system- data- cache and efs partition probably" !
Now,you need to flash the -Correct Pit file- & not only this.You must flash a PIT along with the 4 firmware binaries... AP, BL, CP, & CSC...Now you must enable-check "Re-Partition" in Odin’s PIT tab...
_You need the correct samsung usb drivers on pc,the latest version of Odin,and the correct stock Rom-Firmware for your device (the latest build 3/2020 android 9)..
[Take the correct last firmware for your device & country - (SM-T830?) - here :
_ 1.) https://www.sammobile.com/samsung/galaxy-tab-s4/firmware/#SM-T830
_ OR : 2.) https://samdb.org/model/SM-T830/
_OR (filter by region & android 9) : 3.) https://updato.com/firmware-archive-select-model/?q=SM-T830&exact=1 ]
(you probably need a good Internet connection and necessary patience)
_ Odin3-v3.14.4 : https://mega.nz/file/9qJmgSSK#Cshs38XE9FWVT2A64-JphH38WiwO_zS-W95cjuBbktM
_ Latest Samsung usb drivers : https://androidmtk.com/download-samsung-usb-drivers (after Installing or uninstalling usb drivers,reboot your pc)
_ *Tutorial: how to flash stock rom "4 files" etc : https://rootsamsung.com/flash-samsung-stock-firmware-4-files
**_Read Carefully! here step by step,without haste: https://technastic.com/odin-nand-erase-samsung/
**_How to extract samsung Pit file from samsung firmware : https://androidmore.com/extract-samsung-pit-file/
sry for english & GL

Hey daitalos,
Thanks for the reply and no worries, your english is pretty good. You're right about creating a nandroid backup and I wished I had installed TWRP before I had this issue or at least turn off the FRP lock. I usually root all my device once it comes in to my possession but some reason I decided to keep this one stock.
I just got my device back from an authorize Samsung repair and they couldn't do anything about flashing the device so I'm left with repairing this device myself. I'll follow your guide and will let you know how it goes.
Thank you again for taking the time to help me out! I really appreciated it!

My galaxy tab s4 t830 is in bootloop after flashing with odin. Really need help urgently. Tnx

Webbtech said:
My galaxy tab s4 t830 is in bootloop after flashing with odin. Really need help urgently. Tnx
Click to expand...
Click to collapse
What exactly do you mean ? The device enters in download and recovery mode? What did you try to flash? did you touch anything else on the Odin? Odin must be in the "default" mode!
More Info are needed...
__(OEM unlock toggle & USB debugging is On? - If the device can enter in recovery mode, select “wipe data factory reset” - "wipe cache partition" & Reboot )