Develop Bugs

HTC Desire Help Needed

hello i have desire with
BRAVO PVT1 SHIP S-ON
HBOOT-0.93.001
MICROP-031D
TOUCH PANEL-SYNT0101
RADIO-5.11.05.27
AUG 10 2010.17:52:10
ITS STUCK ON HTC LOGO . I CAN GO IN HBOOT BUT PROBLEM IS I TRIED MANY ROMS BUT ITS ALWAYS SAY MAIN FIRMWARE IS OLDER FLASHING FAILED
ITS ORANGE BRANDED PHONE
PLEASE HELP NEEDED ANY EXPERT

Did you root?
Sent from CM7

no i dint root . can i root phone in this condotion? if possible please can u tell me the way?

you can root in hboot screen.
and root tools ,I suggest unrevoked 3.21 (root tools included clockworkmod 2.5.x recovery) .
good luck man.

You can't flash roms without rooting. Download this and if your on Windows, download the drivers too and also read the page so the drivers install properly. After you have done all of that, run the utility. Please be aware that issues may arrise when your done and no one but yourself takes responsibility what happens, but nontheless, it should be fine.
When your done rooting, go into the recovery and go to backup and restore > backup and it will backup the whole phone. Keep this just in case. It will go on your SD Card > clockworkmod/backup.

my phone is connected in HBOOT but unrevoked say connect phone in usb debugging mode now how can i connect in debuging while phone can only enter in HBOOT

I have the exact same problem, I applied the f***** HTC update and the phone never started afterwards. Just the HTC logo then reboots.
I will try to root the phone as suggested by Meaple and kosterz and will let you know how it turns.

HTC Desire help
Dear xda community
I have a O2 htc desire from uk. Warranty expired. ( now I m in Pakistan so it is not possible to me send it to htc company because here is no htc service shop and If I send it uk or other country expenditure are more than phone price) When I update it with 2.14.207.3 during updating wifi disconnect and phone stacked I remove the battery and on it. Now it stacked on htc logo and show 4 exclamation sign in triangular.
Picture
When I connect it with pc and then disconnect it screen will be appear
Picture
Bravo PVT1 ship s-on
Hboot-0.93 0001
Microp-031d
Toutch Panel-synt0101
Radio 0-5.11.05.27
Aug 10 2010.17.52.10
RUU
No volume key , menu key or back key work
I try to O2 2.14.207.1 rom Ruu upload but when it reached at 85% green installation bar full on the phone and message appear.
ERROR [110]: FILE OPEN ERROR
This error message indicates that the RUU lacks some specific files or they are damaged, so the RUU cannot continue with the update. You have to get the complete RUU package and try again.
And at the pc recover your phone after all process recover successful but when I on the phone it is on same condition
I download this rom from many sites and try it but result is same.
In RUU read me file they said that
Q: I used RUU to update and it failed. Now, my Android phone always boots in the RUU failed mode and cannot enter the Android Home screen anymore, what should I do?
A: This is normal and can be recovered. Follow the instructions below to reset your Android phone and to establish a connection with the PC.
1. Disconnect your Android phone from the USB cable.
2. Reset your Android phone (Remove and reinstall the battery).
3. Reconnect your Android Phone to the USB cable.
4. Check if the Android phone is recognized by the PC.
5. Return to the ROM Update Utility.
So please tell me any solution. I will be thankful to you.

anyhelp from anybody els?

[Q] HTC Desire during updating wifi failed

Dear xda community
I have a O2 htc desire from uk. Warranty expired. ( now I m in Pakistan so it is not possible to me send it to htc company because here is no htc service shop and If I send it uk or other country expenditure are more than phone price) When I update it with 2.14.207.3 during updating wifi disconnect and phone stacked I remove the battery and on it. Now it stacked on htc logo and show 4 exclamation sign in triangular.
Picture attached
When I connect it with pc and then disconnect it screen will be appear
Picture attached
Bravo PVT1 ship s-on
Hboot-0.93 0001
Microp-031d
Toutch Panel-synt0101
Radio 0-5.11.05.27
Aug 10 2010.17.52.10[/COLOR]
RUU
No volume key , menu key or back key work
I try to O2 2.14.207.1 rom Ruu upload but when it reached at 85% green installation bar full on the phone and message appear.
ERROR [110]: FILE OPEN ERROR
This error message indicates that the RUU lacks some specific files or they are damaged, so the RUU cannot continue with the update. You have to get the complete RUU package and try again.
And at the pc recover your phone after all process recover successful but when I on the phone it is on same condition
I download this rom from many sites and try it but result is same.
In RUU read me file they said that
Q: I used RUU to update and it failed. Now, my Android phone always boots in the RUU failed mode and cannot enter the Android Home screen anymore, what should I do?
A: This is normal and can be recovered. Follow the instructions below to reset your Android phone and to establish a connection with the PC.
1. Disconnect your Android phone from the USB cable.
2. Reset your Android phone (Remove and reinstall the battery).
3. Reconnect your Android Phone to the USB cable.
4. Check if the Android phone is recognized by the PC.
5. Return to the ROM Update Utility.
So please tell me any solution. I will be thankful to you.

Download and run this. You might need a Goldcard though
http://www.multiupload.com/LEJCW182AH

[Q] HTC desire in Hboot mode volum and other keys not work

friends
Dear xda community
I have a O2 htc desire from uk. Warranty expired. ( now I m in Pakistan so it is not possible to me send it to htc company because here is no htc service shop and If I send it uk or other country expenditure are more than phone price) When I update it with 2.14.207.3 during updating wifi disconnected and phone stucked/Halted. I remove the battery and switched on it. Now it stucked on htc logo and show 4 exclamation signs in 4 corners of screen.
When I connect it with pc and then disconnect that screen will be appeared.
Bravo PVT1 ship s-on
Hboot-0.93 0001
Microp-031d
Toutch Panel-synt0101
Radio 0-5.11.05.27
Aug 10 2010.17.52.10
RUU
No volume key, menu key or back key work
I try to O2 2.14.207.1 rom Ruu upload but when it reached at 85% green installation bar full on the phone and message appear.
ERROR [110]: FILE OPEN ERROR
This error message indicates that the RUU lacks some specific files or they are damaged, so the RUU cannot continue with the update. You have to get the complete RUU package and try again.
And at the pc recover your phone after all process recover successful but when I switched on the phone it is on same condition
I download this rom from many sites and try it but result is same.
In RUU read me file they said that
Q: I used RUU to update and it failed. Now, my Android phone always boots in the RUU failed mode and cannot enter the Android Home screen anymore, what should I do?
A: This is normal and can be recovered. Follow the instructions below to reset your Android phone and to establish a connection with the PC.
1. Disconnect your Android phone from the USB cable.
2. Reset your Android phone (Remove and reinstall the battery).
3. Reconnect your Android Phone to the USB cable.
4. Check if the Android phone is recognized by the PC.
5. Return to the ROM Update Utility.
So please tell me any solution. I will be thankful to you.

With the phone OFF, can you press and hold the Vol - key, then at the same time, press and release the Power button? It should boot into a recovery menu.

Go get the latest ruu, wwe version and use that. You maybe might have to create a goldcard buy that's only if you get a Cid problem.
Sent from CM7

Yeah, when you said your "buttons" do not work, well, it leaves a lot to the imagination......
Can you goto Bootloader??? Or is it only when you get the white sceen of "almost death"?

HTC desire in Hboot mode volum and other keys not work
dears
my phone is s-on and in the H-boot loader mode. i also make a goldcard but keys are not work and i can't change it to recovery or other mode.
ples help me

[Q] HTC Logo with 4 triangles with exclamation marks

Hi Guys,
Was flashing a new Radio image with Advanced Hack Kit to my Desire HD and knocked my USB cable at about 80% in. Communication stopped and in a moment of maddness I pulled the battery and reset the phone. Of course I am now left with the HTC logo in the centre of the screen and a triangle with exclamation in each corner of the screen.
Attempting to boot into vol+ and power the phone but I get 3 vibrations and orange light flashing, after doing research this means Desire is in Qualcomm upload mode?
Having to remove the battery to get it to turn off vol- and power does nothing but power on and present the splash with exclamations.
Removing the battery again and turning on phone normally when usb cable is removed from device white bootloader screen shows but with no boot options, there is some information there:
ACE PVT SHIP S-OFF RL
HBOOT-0.85.0024
MICROP-0438
RADIO-26.09.04.11_M2
eMMC-boot
Apr 12 2011, 00:55:45
RUU
RUU is selected as default but cannot be chosen when pressing power.
Can anyone tell me what current state the phone is in as some people say this is a soft brick and others are saying proper brick go JTAG or send in for repair to manufacturer.
Any assistance on this would be great, I've researched it a lot but cannot find the definitive answers so now I'm turning to the pro's for help

hi i was stock on htc screen on my htc desire hd
after using the same program as you
i took my sd card out put it into my pc coped the following correct file on to the root of your sd card
mine was htc eu (simfree)
PD98IMG-GB2.zip file
renamed to PD98IMG.zip then booted to hboot then it did the rest
now i used the advanced ace again & worked this time
now have custom rom on with beats audio
hope it helps

richardrs123 said:
hi i was stock on htc screen on my htc desire hd
after using the same program as you
i took my sd card out put it into my pc coped the following correct file on to the root of your sd card
mine was htc eu (simfree)
PD98IMG-GB2.zip file
renamed to PD98IMG.zip then booted to hboot then it did the rest
now i used the advanced ace again & worked this time
now have custom rom on with beats audio
hope it helps
Click to expand...
Click to collapse
Thanks Richards123,
Mine was a little more complicated so here goes:
Fastboot was still working but it was very limited, ADB connection (normal usb) was not, so could not create a goldcard or use any S-OFF tools, the hboot was showing s-off but nothing could be copied, no eng-off? (not a full root).
After messing around with Qualcomm x64 drivers in an attempt to get adb to work (i saw this as being the crucial part of being able to go down the restoration routes that were popular, re-rom etc..
Eventually I was looking at websites on how to install the qualcomm drivers on Win7 x64, found the info that I needed (Qualcomm HS-USB 9002) and it installed as Com4, it was on the same page that I found the fastboot commands
'fastboot oem enableqxdm 0'
and then
'fastboot oem boot'
Desire restarted, showed normal white splash and has now loaded straight into the ROM, back to normal
Took me 7 hours but got there in the end, also using a different usb cable now advise anyone who *thinks* they have bricked their HTC to not panic, if you can still talk to it with a computer with either adb (the best, definately fixable) or fastboot (slightly more difficult) then it is fixable, don't send it to anyone to fix, SEARCH the forums (like I did after posting this hasty post) and talk to the geekiest friend you have
This is why I have taken the time to type up my experiences/fix

ratking said:
Thanks Richards123,
Mine was a little more complicated so here goes:
Fastboot was still working but it was very limited, ADB connection (normal usb) was not, so could not create a goldcard or use any S-OFF tools, the hboot was showing s-off but nothing could be copied, no eng-off? (not a full root).
After messing around with Qualcomm x64 drivers in an attempt to get adb to work (i saw this as being the crucial part of being able to go down the restoration routes that were popular, re-rom etc..
Eventually I was looking at websites on how to install the qualcomm drivers on Win7 x64, found the info that I needed (Qualcomm HS-USB 9002) and it installed as Com4, it was on the same page that I found the fastboot commands
'fastboot oem enableqxdm 0'
and then
'fastboot oem boot'
Desire restarted, showed normal white splash and has now loaded straight into the ROM, back to normal
Took me 7 hours but got there in the end, also using a different usb cable now advise anyone who *thinks* they have bricked their HTC to not panic, if you can still talk to it with a computer with either adb (the best, definately fixable) or fastboot (slightly more difficult) then it is fixable, don't send it to anyone to fix, SEARCH the forums (like I did after posting this hasty post) and talk to the geekiest friend you have
This is why I have taken the time to type up my experiences/fix
Click to expand...
Click to collapse
I had same issue on my sensation. IT WORKED for me too!!! Many thanks!

richardrs123 said:
hi i was stock on htc screen on my htc desire hd
after using the same program as you
i took my sd card out put it into my pc coped the following correct file on to the root of your sd card
mine was htc eu (simfree)
PD98IMG-GB2.zip file
renamed to PD98IMG.zip then booted to hboot then it did the rest
now i used the advanced ace again & worked this time
now have custom rom on with beats audio
hope it helps
Click to expand...
Click to collapse
You don't know how much you've helped me! I have been trying for 12 hours now to fix my problem (http://forum.xda-developers.com/showthread.php?t=1685426), when I stumbled upon your solution. Many thanks (could only press once ) to you my friend!

[Q] Making a Goldcard when stuck at HTC logo while booting

Hey Guys, i wanted to ask if there is a possibility to make a Goldcard to rescue my Desire HD
I bought it on Ebay and it does only boot to the HTC Logo on white screen...
Some Facts:
-Its a Vodafone DE CID so i cannot take a RUU because it does not exist...
-Fastboot works, is detected on PC and may be the only way to access the phone.
Thanks for your Attention

Go to fastboot and type fastboot devices in a cmd prompt

Can't help unless u do that