So if you guys are wondering what a privacy screen protector is, its basically one in which restricts viewing of the phone screen, so basically if anyone is standing or sitting next to you whilst you were on your phone, and they had a look at your screen, then all they would see is a black screen
So the one I ordered really cheap was this
It arrived pretty promptly and applied it the standard method, clean screen, use a credit card and slowly apply pressure as your placing the screen protector to ensure no air bubbles
What do I think? Well the protector is relatively thick and scratch resistant which means I have extra comfort in knowing its safer from drops etc. The screen protector is a fairly good size, easily covers the screen. It does its job perfectly, from side views, the screen can't be seen whatsoever
Disadvantages - I'm used to having my phone lying on the desk next to me, and so if I want to quickly see any notifications, I actually have to pick up the phone and bring it face to face with me, instead of usually just glancing across at it
2) It does reduce brightness so you need to bump it up a little, however the screen protector is described as having 99% UV protection and i've tested it outdoors and I could see the screen okay
Overall I'd recommend this, its cheap, you can't go wrong with the thick protection and the privacy factor is another bonus!
Have you tried with polaroid glasses on too?
Bright.Light said:
Have you tried with polaroid glasses on too?
Click to expand...
Click to collapse
I'll get back to you, just about to go on holiday with the camera so I'll report back what its like under completely bright conditions with sunglasses
My nexus phone has about 10 bad scratches and now has a hairline crack on the screen. I have NEVER EVER has a broken screen going back to my sprint PPC 6601? I dont know what hardened glass they used but it sucks
That's why I always use a wet apply screen protector, I recommend one for your next phone.
Two, 1/8" scratches on my phone is, without using a screen protector since about May is all I got, really not even noticeable unless looking for them. Even took it to the beach twice, sorry for your bad luck OP.
I'm using my GNex since its Germany launch in November 2011 without a screen protector or a case, took it to the beach, used it several times as a flash light while fixing my car, have it on the laboratory table at work next to different solvents, and went many times drinking with it and found it on the floor the next day. All it got is a barely visible 1cm scratch that you can only see in the right light if you know where to look.
So sorry for your bad luck, but the hardened glass is sufficient for my usage.
9 months without a case or screen protector for me. Not a mark on it anywhere. :good:
Only got a small one under ear speaker. Screen itself is flawless. No protector for 8 months now...
Hello
I have my HTC One M9 Prime CE for a week. I think it was a good choice, but I noticed one disturbing issue - small gap between screen and frame. This is picture of it:
i.imgur.com/CdmDflW.jpg (sorry for non-clickable link but I haven't 10 posts)
I hope it's clear enough.
There's not any other gaps. This one is very thin, but backlight is clearly visible between the edge of glass and metal frame (not visible if screen is even slightly pressed there). It's possible that dust particles will get between glass and display or will affect backlight? It would be annoying for me. I think that the whole display is bonded and it's not real problem, but I'm not sure.
Of course, my phone is under warranty, however I want to avoid repairs because of a lot of bad opinions.
Thanks for feedback in advance.
The GPEL screen protector is fantastic! No dot matrix, full adhesive, comes with 2, affordable, case friendly & no Halo affect.
The black border is just a tad too big, so you lose a row of pixels..
https://www.amazon.com/dp/B07D1CG8QY/ref=cm_sw_r_cp_apa_MQYCBbYM79AP7
Thanks for sharing the review!
Hello,
Does the black line cut from the sides of the screen ? Or the bottom ?
Thank you !
Al3xxxinho said:
Hello,
Does the black line cut from the sides of the screen ? Or the bottom ?
Thank you !
Click to expand...
Click to collapse
I currently have this protector, as stated in the OP it cuts off a little on all sides and is it a bit crooked. I have plans to review another screen protector (might be the one) in a new thread soon
So, anyone that sells this internationally for less than 15usd for shipping?
8bitbang said:
I currently have this protector, as stated in the OP it cuts off a little on all sides and is it a bit crooked. I have plans to review another screen protector (might be the one) in a new thread soon
Click to expand...
Click to collapse
Care to share which one? I just picked up a g7 yesterday, have a SUPCASE UB Pro on order, want to pull the included plastic shield, put on glass.
The gpel sounds good, but I'm interested in seeing what else looks solid. (Not interested in going to the $50 dome glass.)
Sent from my LM-G710VM using Tapatalk
markfm said:
Care to share which one? I just picked up a g7 yesterday, have a SUPCASE UB Pro on order, want to pull the included plastic shield, put on glass.
The gpel sounds good, but I'm interested in seeing what else looks solid. (Not interested in going to the $50 dome glass.)
Click to expand...
Click to collapse
I have 2 g7s one with gpel and dome glass. Do you want a side by side comparsion picture. Either is perfect and has flaws
8bitbang said:
I have 2 g7s one with gpel and dome glass. Do you want a side by side comparsion picture. Either is perfect and has flaws
Click to expand...
Click to collapse
Sure, thanks!
Sent from my LM-G710VM using Tapatalk
Dome is on the left and GPEL is on the right
Dome - doesn't affect the sensors but it's smaller than the actual display. It's a bit too short on the left and right sides. This causes light bleed on the edge of the screen protector. Dust magnet but less likely to have bubbles
GPEL - affects sensors and black borders cut off display and is especially noticeable when watching YouTube videos in full screen pinch. Bubbles can happen
8bitbang said:
Dome is on the left and GPEL is on the right
Dome - doesn't affect the sensors but it's smaller than the actual display. It's a bit too short on the left and right sides. This causes light bleed on the edge of the screen protector. Dust magnet but less likely to have bubbles
GPEL - affects sensors and black borders cut off display and is especially noticeable when watching YouTube videos in full screen pinch. Bubbles can happen
Click to expand...
Click to collapse
What are the sensor impacts from using the gpel?
Sent from my LM-G710VM using Tapatalk
markfm said:
What are the sensor impacts from using the gpel?
Click to expand...
Click to collapse
It can cause the display to dim and sometimes turn off like when you raise your phone to answer a call. To be fair all full cover screen protectors are suffering for this flaw. Even OtterBox is getting massive hate for their version and is temporary unavailable.
Just to let you guys know,
You will NOT have the "notch" border pixel line problem if you perfectly align the holes at the top with the sensors, but with a catch: you have to align it with the sensor being more towards the bottom than dead center. My very first screen protector had it more towards the top (basically, the entire protector aligned downwards 1mm, which made the notch very prominent). Then I wasted two more trying to make it bottom aligned. (edit). That fixes the sensor problem and the pixel problem at the top with the notch, unless you are looking down at the phone from above the phone (and who the hell does that?). Unfortunately, perfect alignment is expensive and will cost you several screen protectors since you have to deal with lifting and replanting as well as small nudging WHILE you are in a steamy bathroom hoping for no dust hairs to drop on something. Took me three of them to get it perfect. But I got perfect and I'm pleased.
The left and right sides black bars aren't a problem; the missing pixel line can always be seen by looking to the side of the phone. Just remember to focus on aligning the TOP first (edit) align the ridged sensor so it's almost touching the bottom cutout) and then pressing the top down, then the middle. That's the hard part. This will also cause a few air bubbles on the sides, which means you will have to carefully lift the edges and press outwards to reapply again, and make very sure your fingernails are spotless. That is going to be the risk of dust getting in there, so be careful. Get it perfect then everything will make you happy.
The results are worth it.
Falkentyne said:
Just to let you guys know,
You will NOT have the "notch" border pixel line problem if you perfectly align the holes at the top with the sensors. That fixes the sensor problem and the pixel problem at the top with the notch, unless you are looking down at the phone from above the phone (and who the hell does that?). Unfortunately, perfect alignment is expensive and will cost you several screen protectors since you have to deal with lifting and replanting as well as small nudging WHILE you are in a steamy bathroom hoping for no dust hairs to drop on something. Took me three of them to get it perfect. But I got perfect and I'm pleased.
The left and right sides black bars aren't a problem; the missing pixel line can always be seen by looking to the side of the phone. Just remember to focus on aligning the TOP first and then pressing the top down, then the middle. That's the hard part. This will also cause a few air bubbles on the sides, which means you will have to carefully lift the edges and press outwards to reapply again, and make very sure your fingernails are spotless. That is going to be the risk of dust getting in there, so be careful. Get it perfect then everything will make you happy.
The results are worth it.
Click to expand...
Click to collapse
Where's your proof? Both the OP and me have reported information (with evidence mind you) that contradicts your statements.
8bitbang said:
Where's your proof? Both the OP and me have reported information (with evidence mind you) that contradicts your statements.
Click to expand...
Click to collapse
My proof is me owning the phone and going through 4 GPEL screen protectors before I got it perfect. I paid my dues. And as someone disabled and on SSI and with a fixed income, I don't have money to go through infinite screen protectors, unlike some of you people here.
The trick is to align the "ridged" sensor so that it's (edit: just looked at my phone: the hole aligned at the -bottom- of the ridged sensor, rather than dead center! but not blocked by the edge of the screen protector), sensor bottom aligned and then after that, making sure all the sides are perfectly straight when applying (a LOT harder than you think, even in a steamy shower, because I'm in an old apartment). Took me 4 protectors and cost me over $30 dollars. (air bubbles and dust from me constantly having to re-lift to get the orientation perfect and eventually dust getting under the edges, and I have OCD so I want nothing less than perfection). Might even give GPEL an email and see if they'll send me an extra sample for my troubles. And no, I have no way to take a picture of the phone screen for you.
I forgot that I had it 'bottom' side sensor aligned rather than mid sensor aligned because I spent over 30 minutes in the shower sweating and uncomfortable wasting screen protectors trying to get rid of the notch line and getting it on with air bubbles. I was extremely stressed out, and it's difficult for someone with a metal bar in their spine to have to work that hard. Needless to say the fourth protector (thank god) I got absolutely perfect.
If it's dead center yes you will have a pixel row of the notch visible. So you have to 'raise' the protector upwards by that same pixel space. There's enough cutout to work with to make that work.
This is no problem because the very *BOTTOM* of the phone isn't used by the display (since this is an IPS display; someone mentioned this in a review, compared to OLED), unlike the top, so you have like 1mm of extra room to work with for the cutout (as long as the top sensor isn't blocked by the bottom edge of the protector). The black border at the bottom won't interfere with anything (checked with a screen test in the service menu).
I'll -try- to upload a picture of the phone with my laptop's built in camera if I can later on, but please don't be upset if you don't like the quality. My laptop isn't high definition and isn't made for such precise pictures. 720p isn't going to work very well.
@Falkentyne - thanks for the explanation.
It sounds like the critical part is where the protector is relative to the front mounted speaker (towards the right edge of the notch) front mounted camera (center of the notch), mystery circle to the left of the camera, and tiny notification led circle furthest to the left side of the notch?
If a photo of your own screen is hard to get, I've attached a photo, the top part of the g7 screen. Maybe draw a line showing where the gpel edge needs to be (outside edge of the line = outside edge of the gpel).
This is the best I could do.
markfm said:
@Falkentyne - thanks for the explanation.
It sounds like the critical part is where the protector is relative to the front mounted speaker (towards the right edge of the notch) front mounted camera (center of the notch), mystery circle to the left of the camera, and tiny notification led circle furthest to the left side of the notch?
If a photo of your own screen is hard to get, I've attached a photo, the top part of the g7 screen. Maybe draw a line showing where the gpel edge needs to be (outside edge of the line = outside edge of the gpel).
Click to expand...
Click to collapse
In your picture, move the screen protector UP about 1mm upwards so the bottom is where the red line is.
This will leave about 1mm of 'extra' space above the sensor area (whatever that thing is, sensor, microphone, I don't know). But it will still fit fully into the enclosure.
Took me 4 screen protectors to do this AND have no spare dust hairs from all the relifting !
Perfect thanks!
Just over the bottom edge of the front speaker (the oval on the right with the grid pattern).
I just got my gpel protectors in today, will give it a try tomorrow.
I installed it following your suggestion, it seems to be working fine. Thanks for the info!
markfm said:
I installed it following your suggestion, it seems to be working fine. Thanks for the info!
Click to expand...
Click to collapse
Glad you got it working and got the results you wanted.
It's good that the cutout is slightly larger than the speaker(and sensor/camera) itself, but bad that people won't know about this without experimentation (or somehow coming across the posts here).
Is the screen polarized or is it possibly my screen protector?
I was driving with the top down and polarized sunglasses and noticed I could barely see my screen unless I tilt my head to the right (horizontal mounted)
Just wanted to see if anyone else noticed this.
I wonder if it's the preinstalled protector. Wearing my sunglasses I can barely see the screen. My s10+ right next to the s20 is clearly visible aside from being a bit darker obviously. I don't want to tear off the protector to see if it makes a difference..
I've got a WS glass protector. I can view mine in either horizontal or vertical no problem. It disappears if I point the top of the phone at 2:30 or 7:30 only. So really no problems for mine.
Its your sunglasses not working well with that type of screen, i have Oakley polarised and several different smartphones have the same issue for me.
This problem has been an issue for years, a search online will tell you the filters on the polarized glasses negates the light on the cell phone screen and how to work around it, try turning your phone 90° and see what happens.
Sent from my S20 Ultra