Just unlocked my bootloader and flashed clockwork recovery - pretty easy.
I have a Vodafone UK provided device that has vodafone's CID.
My Firmware version is 1.26 currently.
If i wanted to put Android Revolution 3.0.0 on the device it is suggested i need to upgrade the firmware?
When i look at the firmware page it says its only supported by certain CID numbers and when i check mine it says none
Can i still put it on or do i risk bricking?
Since you're CID is not listed, my guess is that it will either not install, give bootloop or brick.
Keep reading and let people develop some more.
Sent from my HTC One X using xda premium
My HTC One X is on Vodafone too. I unlocked it etc from the guides on XDA and HTCDEV.
I've been using the ARHD ROMS for a few days now, they're better than what Vodafone provided. Today I flashed the ARHD 3 ROM. First I did the 3 boot image via fastboot then flashed the ROM via recovery, I always wipe cache and dalvik cache between ARHD ROMs and so far it's working fine. No brick here...
If you've got this far I reckon you can fastboot flash the boot image and upgrade to ARHD 3 no problem at all - go for it I say...
linkisoc - with your phone on the arhd rom and unlocked from HTCdev, are you able to change the CID?
I'll confess I never even considered the CID. It's not something I'd come across before with several android phones all rooted / flashed etc. I've been doing this since the Google Nexus one, Nexus S, Samsung Galaxy Nexus and now the One X... checking the CID never occured to me...I'll google it now though and see if I've just been very lucky !
i've never changed it either - always managed to get unbranded sets this far but was far too keen for this phone and got it from vodafone on release day, complete with all their crap and slow OTA releases. I asked in another post about the difference between htcdev unlock and an eventual S-OFF and apparently they're different.
Hi,
I recently managed to root my HTC One M8s with TWRP recovery and everything works perfectly, except that I can't install the new OTA (1.16.401.1).
After searching I have flashed my recovery back to the stock for my version (which is 1.11.401.1) and tried applying the OTA again, but it still fails.
I downloaded the recovery from this website: ruu.lalleman.net/HTC_M8S%28QL_UL%29/Recovery/HTC%20Recovery/ (I can't post URLs yet).
Below is the error I receive when trying to update on stock recovery, TWRP recovery also gave the same error when I tried updating there.
(Code -1)
E:Find no match PARTITION: for package path @/cache/recover/block.map
Finding update package...
Opening update package...
Verifying update package...
Installing update...
L50QCT.01.105.019
Verifying current sytem...
Package expects build fingerprint of htc/m8qlul_htc_europe/htc_m8qlul:5.0.2/LRX22G/531284.2:user/release-keys or htc/m8qlul_htc_europe/htc_m8qlul:5.0.2/LRX22G/555949.10:user/release-keys;
This device has htc/m8qlul_htc_europe/htc_m8qlul:5.0.2/LRX22G/53128
E:Error in @/cache/recovery/block.map
(Status 7)
From what I can see my build fingerprint is incorrect, but I have no idea how to fix it...
Seems to me it's likely that you've altered some system files while rooted and the Ota doesn't like it.
Now, I don't own an M8s...i have an M8, but I'd say the easiest route would be to flash your stock ruu again. After that the OTA should work.
It's that or figure out what system changes have been made and correct it. Xposed can mess you up, Uninstalled system apps can stop the Ota... MODS that changed system files... Etc. The Ota us looking for a stock system, then it updates it.
Good luck!
Thanks for the answer, I will see if I can try this solution tomorrow. I just have 2 questions:
What does the RUU do exactly? Should I see it as a complete stock reset of my phone?
And can I simply flash it using fastboot or is there a special method for a RUU?
My previous phone had an automated root and I always updated with OTA afterwards so I never flashed before now.
Im on the same boat. Tried to sim unlock by rooting and playing with CID but didnt work, now ive a rooted m8s and no ota. Tried to ruu but kept getting an error something like not enough space although i had 10gb free, cleared cache rebooted. Cant even factory reset. If anyone know how to unroot it and bring it back to stock that would be fantastic. Kind of want to delete the "flag" too make it "LOCKED" and "OFFICIAL" incase for warranty. Any ideas?
You guys have flashed 1.16 before, haven't you...?
See here: http://forum.xda-developers.com/htc-one-m8/help/help-thread-htc-one-m8s-to-stock-howto-t3190238
Err, oops, posted too soon. You said you have flashed to 1.11. What is the full filename of the RUU you flashed?
voidzero said:
You guys have flashed 1.16 before, haven't you...?
See here: http://forum.xda-developers.com/htc-one-m8/help/help-thread-htc-one-m8s-to-stock-howto-t3190238
Err, oops, posted too soon. You said you have flashed to 1.11. What is the full filename of the RUU you flashed?
Click to expand...
Click to collapse
When I got my phone I updated with OTA to version 1.11, after that I flashed TWRP recovery and rooted my phone. Now that OTA 1.16 is out I tried to update but couldn't, so I tried to flash back to stock recovery but it still wouldn't work because of the error above. Now it would seem that I am doing this the wrong way, and you cannot use OTA on a rooted/unlocked/custom recovery M8s.
Manual OTA flash worked on my previous phone with root which was an ASUS Padfone Infinity A80 as ASUS would release them on their own website for you.
Apparently HTC does not do this, or I am not looking in the right place.
I have never flashed a RUU before, and I don't know how to lock my bootloader again. From what I understand, every time there is a new OTA I will have to lock my bootloader, flash original recovery, flash RUU and then update. That sounds like a lot of trouble every time a new OTA comes out.
Is there no way to manually flash the new OTA without losing root, custom recovery and locking the bootloader? Will I have to follow these steps every time? Also I use the built in back-up to Google as well as HTC back-up but I don't know if all my data is in those back-ups or if I will lose something.
Codyksp said:
(...) so I tried to flash back to stock recovery but it still wouldn't work because of the error above. Now it would seem that I am doing this the wrong way, and you cannot use OTA on a rooted/unlocked/custom recovery M8s.
(..)
I have never flashed a RUU before, and I don't know how to lock my bootloader again. From what I understand, every time there is a new OTA I will have to lock my bootloader, flash custom recovery, flash RUU and then update. That sounds like a lot of trouble every time a new OTA comes out.
(...)
Is there no way to manually flash the new OTA without losing root, custom recovery and locking the bootloader? Will I have to follow these steps every time? Also I use the built in back-up to Google as well as HTC back-up but I don't know if all my data is in those back-ups or if I will lose something.
Click to expand...
Click to collapse
If you restore a RUU, and afterwards don't flash your recovery and boot partitions, You will see "Software status: official" in fastboot.
Now here's the trick: if you just boot a custom recovery with "fastboot boot my_recovery.img" (TWRP for example) then it will boot TWRP, but you can make the modifications to your system partition without losing "Software status: official" in fastboot.
So: If you just boot your recovery with 'fastboot boot' and don't flash anything, you can make all the modifications you want and still be able to install OTAs later, I think. I've rooted my phone, even installed XPosed, done all kinds of funky things to it but Fastboot still shows me that I'm on official software.
How does that sound?
So since there is no decent guide at all about flashing RUU for a HTC One M8s (the s makes a difference!). I have assumed that I need to have the bootloader locked first, as I unlocked it. According to all the M8 guides I have to gain S-OFF before I can lock the bootloader again. So I followed a guide to wipe with TWRP and flash a ROM called InsertCoin so that I can S-OFF my phone.
Now after going through the ROM's setup my phone is stuck in a bootloop, constantly trying to boot up. There is NO way at all for me to get it to stop, it just keeps booting the entire time. Not a single combination of buttons is working. Good thing the battery is non removable. How am I supposed to fix this? I've tried every volume up/down/power combination possible. The phone just boots to the HTC - Power by Android screen, shuts off after about 5 seconds and then repeats the same thing over and over. I can't turn it off and I can't get to the bootloader either.
What I need is a guide that tells me all the steps required to get an HTC One M8s (NOT M8!) back to 100% stock. This means, stock ROM, stock recovery, locked bootloader and S-ON. I am getting extremely frustrated by the lack of information and the amount of redicilous things I need to do just so I can root my phone and have OTA as well.
All I want is root on my phone for 1 app that I use with my car radio and I want to be able to update to the newest OTA afterwards, is that really so much to ask?
I am fine with installing a custom ROM with root and easy updates too, as long as the damn phone will boot after installing it and it's actually made for the M8s.
Deleted......
Well I finally managed to get the damn thing to the bootloader, and I've used "fastboot oem lock" to relock my bootloader. It now shows ***Software status: Modified ***, *** RELOCKED *** and ***Security Warning ***.
I will now have to go to my parents where my laptop is to be able to copy the RUU to my SD card, from what I understand it has to be named 0PKVIMG.zip and then it should automatically install.
Now the phone says it can't find the image or the image is incorrect.... It searches for, 0PKVDIAG.zip, 0PKVDIAG.nbh, 0PKVIMG.zip or 0PKVIMG.img. and it seems to find 0PKVIMG.zip and loads it but it cannot find the .img file and does absolutely nothing. Am I supposed to have both?
So it turns out that the RUU zip from http://ruu.lalleman.net/HTC_M8S%28QL_UL%29/RUU/ is actually not correct and I had to use rom.zip which was inside the folder. The phone is now running the "update" as it calls it. Fingers crossed...
Yes, possible you need to use rom.zip inside the zip, depending on the version, but I think this applies to 1.16 which I advice against using for reasons previously specified.
---------- Post added at 07:47 PM ---------- Previous post was at 07:47 PM ----------
By the way, I did write an RUU restoration thread specifically for this subject. Did you not find it?
Apparently I also needed to use the rom.zip for the 1.11 version, in the meantime I have also updated with OTA to 1.16. Afterwards I also unlocked my bootloader, restored my settings and installed SuperSU by booting TWRP. Let's hope the next OTA still works...
I did read your thread but I got stuck at first on relocking the bootloader, as I couldn't find the exact instructions for a while. Afterwards I got stuck on flashing the RUU because I didn't know that I needed to use the rom.zip file to get it to work.
After all that I got quite frustrated and I just wished there was 1 thread with instructions for everything (unlocking, relocking, flashing, compatible ROMs, booting to keep OTA, etc.) which is why I was angry at the time and couldn't properly read everything or find solutions. In the end it all worked out so far though.
I would ask you to create a compilation thread though if you wanted to improve the available information. Either way, thanks for the information that you've already provided.
Codyksp said:
Apparently I also needed to use the rom.zip for the 1.11 version, in the meantime I have also updated with OTA to 1.16. Afterwards I also unlocked my bootloader, restored my settings and installed SuperSU by booting TWRP. Let's hope the next OTA still works...
I did read your thread but I got stuck at first on relocking the bootloader, as I couldn't find the exact instructions for a while. Afterwards I got stuck on flashing the RUU because I didn't know that I needed to use the rom.zip file to get it to work.
After all that I got quite frustrated and I just wished there was 1 thread with instructions for everything (unlocking, relocking, flashing, compatible ROMs, booting to keep OTA, etc.) which is why I was angry at the time and couldn't properly read everything or find solutions. In the end it all worked out so far though.
I would ask you to create a compilation thread though if you wanted to improve the available information. Either way, thanks for the information that you've already provided.
Click to expand...
Click to collapse
The next ota won't work because you rooted it. Root changes binaries which lead to a fail on ota.
You need a non rooted (read : never rooted before) stock rom.
Mr Hofs said:
The next ota won't work because you rooted it. Root changes binaries which lead to a fail on ota.
You need a non rooted (read : never rooted before) stock rom.
Click to expand...
Click to collapse
So in that case I just unroot it before updating then?
Codyksp said:
So in that case I just unroot it before updating then?
Click to expand...
Click to collapse
Read my post again...... "a never rooted rom" so that means you need a stock rom before its ever been rooted. NOT an unrooted one because it leaves traces which will cause the ota to fail !
People should learn to create a nandroid backup before flashing ANY mods/superuser.zip/roms etc......etc
Well developers shouldn't make this such a hassle... My previous phone was an ASUS Padfone Infinity (A80) and it didn't receive any OTAs after being rooted but ASUS simple lets you download the firmware updates on their website and then you can manually update it without any problems. If HTC provides a bootloader unlock, why can't they allow OTA or at least provide manual firmware updates?
I wouldn't mind using a custom ROM either but I have no idea which ROMs work for the HTC One M8s. Would any M8 ROM be compatible? The phones aren't identical, the "s" is there for a reason...
Codyksp said:
Well developers shouldn't make this such a hassle... My previous phone was an ASUS Padfone Infinity (A80) and it didn't receive any OTAs after being rooted but ASUS simple lets you download the firmware updates on their website and then you can manually update it without any problems. If HTC provides a bootloader unlock, why can't they allow OTA or at least provide manual firmware updates?
I wouldn't mind using a custom ROM either but I have no idea which ROMs work for the HTC One M8s. Would any M8 ROM be compatible? The phones aren't identical, the "s" is there for a reason...
Click to expand...
Click to collapse
I would say that M8 roms wouldn't be compatible, and could even mess up your device badly. Sorry!
Codyksp said:
Well developers shouldn't make this such a hassle... My previous phone was an ASUS Padfone Infinity (A80) and it didn't receive any OTAs after being rooted but ASUS simple lets you download the firmware updates on their website and then you can manually update it without any problems. If HTC provides a bootloader unlock, why can't they allow OTA or at least provide manual firmware updates?
I wouldn't mind using a custom ROM either but I have no idea which ROMs work for the HTC One M8s. Would any M8 ROM be compatible? The phones aren't identical, the "s" is there for a reason...
Click to expand...
Click to collapse
Your point of view is a bit off if you ask me. Developers (in this case HTC) do not have to support custom modding of your phone. They support the device in the state you buy it !
If you want to mod it that's YOUR call not theirs. Do some homework before modding it. Getting a phone back to stock for future updates is relatively easy but many people don't read first how to as they think it's not important.
HTC has no obligation at all towards you regarding custom software !
And indeed M8 roms do NOT work on your M8s !
So I installed ViperOne M9, the latest version, everything went fine, the download didn't fail, but after rebooting the phone just boots to the bootloader. I can access recovery mode, and download mode but I can't do anything else. I'm not sure what went wrong, though I suspect it might have been that my phone wasn't updated to the latest firmware, I thought it was but I think it wasn't. I made a TWRP backup and placed it on my SD Card but it doesn't seem to be reading it since nothing shows up in there.
In summary I switched to ViperOne M9 from stock, my bootloader is unlocked and my phone is rooted. Its S-On, and it seems to be rebooting every so often. Can anyone help me, this is my first time flashing a custom ROM and everything seemed to be going well until this step.
ArgusPMC said:
[...]
ViperOne M9, the latest version
[...]
S-On
[...]
Click to expand...
Click to collapse
You need the Android M firmware for the latest Viper version. Not every SKU got that update already. What's your current firmware version (stated in Download Mode in the line with "OS" at the beginning)?
Edit: Pressing and holding the power button and both volume buttons at the same time (for a certain amount of seconds I always forget - was it something around 30?) should end the bootloop and make your phone return to Bootloader Mode.
My current firmware is 2.10.709.180. I looked into the Backup and RUU collection too, though I wasn't sure about what to do with that. I did see a TWRP backup for version 2.10.709.1, but I'm not sure if that's the same as the firmware version I have, give those two digits at the end with my phone. Otherwise I guess I could use an RUU if I understood correctly, but I got that I should look for a specific one for my phone.
My CID is also HTC__621 if that helps anything. I'm also not sure about S-ON, should I go S-OFF, I know there's an app that does it for $25, and if it is better for custom ROMs then I have no issue paying that.
If I'm not mistaking your firmware version belongs to the first of the two updates that install Android M on the Taiwanese version (SKU 709) of the M9. So you probably only installed the preparing one and not the Android M one itself. Unfortunately no one contributed a backup for that version and I don't have enough time at the moment to create one. Since you're S-ON you can't use any of the RUUs either because S-ON prevents you from downgrading or changing to a different SKU. And there is no RUU for your firmware version which is accessible for free.
I would recommend installing one of the Android L custom roms (e.g. Viper One M9 3.5). After that you have four options:
Wait and hope that someone creates and uploads a backup you could use. (Can be combined with option 2)
Wait for an Android M RUU for your SKU. (There's no guarantee that there ever will be one.)
Get S-OFF via Sunshine so that you could use one of the older RUUs for the SKU 709. (They can be found in my google sheet.)
Use this RUU service.
If I were you I would choose option three since S-OFF makes getting back to stock so much easier and you're independent from others uploading a backup that corresponds to your current firmware since you can use any RUU you want with S-OFF. But don't feel pushed by me to choose option 3 (since that's not my intention). It's completely your choice.
I'll just go S-OFF, seems like the easiest solution. I was going to do it anyway, so I might as well do it now.
EDIT: Thanks, your solution worked out for me, now I've just got to use the RUU I downloaded and with that I can go ahead and get the Android M firmware I need.