Related
I've used many different kinds of screen protectors in the past, and this time I tried XtremeGuard which I found on eBay. The cost was only $2.50 shipped. I must say hands down, this is the best screen protector I have used.
Other kinds I've used in the past were a thin hard plastic, kind of like a clear overhead sheet, but thinner and sticky on one side. These were not good IMO, because they make the touchscreens less sensitive and since they were hard, the edges would start to peel first and it would be all downhill from there.
The XtremeGuard is a more stretchy film material, kind of like 3M clear bra, or the kind you would find on a car. Its got a nice grippy rubber feel to it, which I actually like. Its "softer" so it sticks better to the screen.
I used a mild soapy water solution to put it on, and at first was kind of concerned with my results. Some areas were cloudy, there were some visible bubbles and when the screen was on it looked all rainbow cuz of the water trapped inside. After a couple days though, all the moisture evaporated, the cloudiness cleared up and all the bubbles were gone. I was left with a perfectly crystal clear screen that adhered all the way around, even on the edges. You would not be able to tell there was a screen protector on here (I have the OEM HTC silicone skin that covers the edges as well so you can't see the edge of the screen protector). The touchscreen works perfectly, and the screen protector does not interfere at all.
The screen protector was the exact size of the screen, perfect cut. Which is good, but makes it challenging to install, if you're off by a tiny bit, the screen protector will stick off the screen and that will be prone to peeling up later on. So take your time during the install to ensure its on there straight and perfectly. I started from the top where the speaker is and lined it up around those lines, and used a credit card to press it down and get as many bubbles out as I could. If this is your first time installing a screen protector, I would suggest getting 2-3 to make sure you get it right. At only $2.50ea, you really can't go wrong here. I'm 100% satisfied.
http://cgi.ebay.com/NEW-XtremeGUARD...ewItem&pt=PDA_Accessories&hash=item35a9e73eed
I would also like to note that I do not work for, or am in any way affiliated with XtremeGuard at all. I simply tried their product, and I liked it, so I'm leaving my feedback here.
I have tried it, but it is like a mm to long on top to bottom. And it was like 2mm to short in width.
That was my experience. Could be wrong for everyone.
I like mine, it fits perfectly. Doesn't stick over the edge and covers the whole thing. Mine was a perfect fit, not too long or short on any sides.
I'll try to get some pics up later when I get the chance
Man, I want to order it so bad, but with Otterbox covers around the corner, I think its a little waste of money.. :S
Any tackiness or stickiness with this protector? I'm currently using Phatom Skinz and love it, but I'm always looking around for something that may potentially be even better...especially with a price like this. How about orange peel?
thanks,
Alan
There is a very slight tackiness with this screen protector, but I actually like it. It gives a good feel when typing. It might interfere with pong or some other games where you need to move your finger really fast, but that doesn't really apply to me.
No orange peel, or any peeling at all for that matter.
The cloudiness really bugs me. The Zagg I had did not cloud like this one does.
The item from ebay is too pricier. This site offers products with much lower price and free shipping world wide. The 3 packed screen protector is much cheaper than 1 packed from ebay.
http://www.geartaker.com/product/3x...opers&utm_medium=minqing&utm_campaign=FA0070B
this 3 packed protector was once sold at $0.01 during its 2nd super deal.
Hey guys, I recently bought one of these off Amazon when I ordered my Otterbox case, it was only $2 so I figured I had nothing to lose. Here's my take on it.
http://forum.xda-developers.com/showthread.php?p=19109961#post19109961
So what do people recommend as the best screen protectors to choose from for the MT4G?
I know everyone has their own opinions on them, but I'm hoping people can post their pros/cons and we can help us all narrow down the choice to a few.
Thanks!
the phantom skinz screen protector! pros: clear, nice feel, covers the whole front. cons: none if installed correctly.
I like the Reallook one. Clear, durable and feels like the glass.
I had the realook and phantom skinz. I settled on phantom skinz. I have the full body matte, plus clear phantom skinz. (Don't install the matte screen protector from PS).
Realook is very good with clear BUT the only thing that sucks is that you get ALOT of oils/fingerprints, etc on it. Easy install and easy clean with soap/water.
Phantom skinz gets oil on the screen too, but not as much. Screen surface is alittle "gummy". (Orange peel is very little to non existant). Watch out as the adhesive backing will attract lint (during installation) and you WILL not be able to get that off. PS also has lifetime warranty = unlimited screen protector replacements. (got the whole kit for $12 during 50% off cyber monday).
Don't bother getting invisible shield, they suck and give you orange peel, and it's thick.
@Jaylito,
Did you notice any kind of cloudiness after you cleaned your screen with alchol/towel? (assuming you've cleaned your screen with alcohol/water) For some reason, mine clouded up on the top.
yeah I have. I guess it's normal tho. goes away if u keep rubbing the screen back & fourth with ur thumb. guess since the material... if it gets wet, it'll cloud a bit cause the moisture seeps thru the inside but it'll dry out bro.
guess I have to do more rubbing then cause it's still cloudy...
oh well....
I tried PhantomSkinz and that was a pain to put on (w/ water and soap), Realook was easy and it didn't peel at the edges.
Zagg Invisishield. Lifetime Warranty.
realook, hands down.
pros: crystal clear, feels like the glass itself, easy to clean, easy to apply, easy to reapply.
cons: a little expensive ($10 for 2, but its totally worth it)
MT4G_Slave said:
I tried PhantomSkinz and that was a pain to put on (w/ water and soap), Realook was easy and it didn't peel at the edges.
Click to expand...
Click to collapse
Weird... for me, PS was MUCH EASIER than realook.
PS allows movement up/down/left/right with ease, and then you just squeeze out water.
For realook, it sucked to align the edges cause you can't move the film once you've "stickered" it on. Then you have to peel it back off and realign, causing lint (in my case) to adhere, and then I have to clean it again.
For me the realook was the best by far. I tried a couple of the wet app kind like invisishield and clear freak on the 4 mt4gs that I had and the realook was the best. I agree its a pain to put on, especially if you have animals because of dust and hair, but if you apply it in the bathroom after letting it steam up from the shower, I've found I can get it on without too much dust or hair falling on the screen. Also, get some extra scotch tape and place it on the front of the realook screen to keep your fingers off the adhesive side while applying it. Another nice thing is that each protector comes with two dots to apply to the camera lens in the back.
The only bad thing is that I think the realook attracts fingerprint grease worse than the wet app kind.
I have a zagg on my nexus s mostly because its all that's out right now and will put a realook on as soon as they are available.
Sent from my Nexus S using XDA App
The Boxwave screen protectores look pretty good too, though I've never tried one myself.
Ghost Armor. Just added it today on my 4G n its cut to fit perfectly, including the sensors n camera. FEELS like the real glass n doesn't take away from the display like the ones Tmo sales. Avoid those *****es like the plague.
I used Zagg for my Nexus S.
I get generic ones from a guy named lcd-protectors on ebay, 5 for $3.50. They're the stiff kind with two protective layers that you peel off, one before you apply and one after. I'm too cheap to pay more.
i just ordered a full body cover kit from stealthguards.com
choosing the clear type and none of the colored ones, it was $2.85 (full body protection, just pay shipping)
$2.85 sure beats dishing out $25 for zagg which is the same crap.
What do you need a screen protector for? I haven't used a screen protector since I bought the G1 at launch, and I've never had a screen scratch. Keys in my pockets, etc. Never been a problem. These screens are incredibly scratch resistant.
I love these screen protectors that I bought on Amazon. Perfect on the first try with no bubbles! Check it out here: http://www.amazon.com/gp/aw/d/B004E49TEG/ref=mp_s_a_1?qid=1294786757&sr=8-1:
BoxWare screen protector is well IDK how to rate it as it is just regular. What I did not like about it was it does "NOT" fully cover the screen as you have little gap very small which bugs me as I am neat. The feeling right now is artificial as I can tell it is there maybe cuz its still new as I applied it just 2hours ago. So lets wait and see how it turns out in long run.
I grabbed a Reallook screen protector off of amazon:
Pros: The feel and clarity are great
Cons: The cut. It has a cutout for the FFC and leaves a fair bit of space on all sides (as a result it's easy to get on) but it's really short on all sides in my opinion.
Part Four said:
What do you need a screen protector for? I haven't used a screen protector since I bought the G1 at launch, and I've never had a screen scratch. Keys in my pockets, etc. Never been a problem. These screens are incredibly scratch resistant.
Click to expand...
Click to collapse
Tell that to the scratch in my screen that I got the first day of having the phone... yeah, needless to say, I have a screen protector now and its helped a lot.
Sent from my HTC Glacier using XDA App
I was wondering if there are any go to screen proctectors? Any to avoid, like do any cause issues with the touch screen?
Sent from my Galaxy Tab!
I'd avoid the hard plastic static-type. They're difficult to put on without dust. I've been using the ones from clearprotector (.com). 50% off and free ship with the code iwantultra (have it memorized cause I've gotten several). The corners and edges are kind of a ***** to get on, but they work well and come with a lifetime warranty (or so they say...). This is a wet-application so don't use them unless you're willing to take the time to watch the youtube videos to learn how to install, and then takes about 20 minutes to install.
I get mine from www.bestskinsever.com. I've had no problems with them. The screen protector is easy to apply and very durable.
I have Ghost Armor on mine and like it, it is a bit smoother than Zagg or Bestskinsever.
Be warned if you want the full body protection, adding this to the back of my tab caused me to have the newton ring problem. I never had the problem with just the screen protector on, I should I have just stuck with the screen and not the entire thing but I really wanted the matte back on my tab.
Thanks fellas. I have and used to do/use the wet application ones for a while. Then I got tired of them and just went with the cling ones. I think I'll get the wet app and it should last a longgg time. Especially since Im not going to be using the tab every day.
I went with Clarivue on the recommendation of a friend.
It's decent enough, no tackiness or anything like that but it's not the best fitting, could've been a couple of mm wider and taller.
Other than that, whilst I've had a long-standing dislike for them, recently I've found Zagg's InvisibleShield protectors to be pretty decent - they seem to be very well fitted and the tacky feel to them that I remember doesn't seem as noticeable.
Kinda wish I'd gone with them for my Tab
Which would you guys say offers the smoothest screen experiences of all? I don't care about longevity as I only use my tab about once every 2 weeks
Imo the smoothest would be the cling on ones.
Sent from my Galaxy Tab!
I purchased these in July from Amazon. http://www.amazon.com/gp/product/B0058NXPLK
I was never a fan of the "wet" applications, to me it just seemed like too much work and I was never comfortable spraying any type of liquid all over my devices, regardless of how harmless they might be.
But anyway, this is a clear, non-matte protector that is the "static cling" kind of application. Once it goes on properly, you cannot see that is even there. The touch feeling is the same as if you had no protector on. I really feel that those matte ones, while they do reduce sun-glare, a lot of them provide a "tacky" feeling that maybe is fine for a smaller screen such as a phone, but can become very annoying for a larger screen if you do a lot of swiping across the larger surface area of a tablet. But that is a personal thing....I usually don't use my tablet outside in the bright sun anyway, so the matte types are useless for me.
I've had it on since the end of July and it's held up very well. You do have to wipe the smudges off the screen occasionally, but you'd have to do that anyway even with no protector. I'm extremely satisfied with these.
So I've got an Invisible Shield en route for my Tab, will post back when it arrives.
Same here haha.
Sent from my Galaxy Tab!
I just bought the glare-reduction screen protector from BodyGuardz. Has anyone else had any experience with them? I wanted something that would offer a decent amount of protection for the screen (fingerprint and physical pressure), but also not reduce the touch sensitivity at all. (I type with the tip of my nose since I can't use my fingers, and trying to press too hard hurts )
Not sure where you can get it, but here in Singapore there's a brand called DataFlex and their screen protectors seem really good.
I bought SGP steinheil shield ultra optics. I liked it.
Raistlin1 said:
I have Ghost Armor on mine and like it, it is a bit smoother than Zagg or Bestskinsever.
Be warned if you want the full body protection, adding this to the back of my tab caused me to have the newton ring problem. I never had the problem with just the screen protector on, I should I have just stuck with the screen and not the entire thing but I really wanted the matte back on my tab.
Click to expand...
Click to collapse
So this newton ring issue is a major problem. What if I just protect the back and leave the screen open? I have the new logitech keyboard case on the way and the front is protected in the case, but the back is exposed. I planned on protecting the back only. But I wont do anything if it'll case the newton rings.
Newton Ring?
nuprotocol said:
So this newton ring issue is a major problem. What if I just protect the back and leave the screen open? I have the new logitech keyboard case on the way and the front is protected in the case, but the back is exposed. I planned on protecting the back only. But I wont do anything if it'll case the newton rings.
Click to expand...
Click to collapse
Yeah. Same here. Just want a more "grippy" back. How does one produce Newton Rings from the back of the device. Methunked it was a display issue resulting from the interaction of the protector and display glass...kinda by definition...
Hopefully we'll find out soon. I just want to protect the back.
skeeter123 said:
Yeah. Same here. Just want a more "grippy" back. How does one produce Newton Rings from the back of the device. Methunked it was a display issue resulting from the interaction of the protector and display glass...kinda by definition...
Click to expand...
Click to collapse
I blame the install of the rear skin because I had the screen skin installed first and then three weeks later I had the rear done. He turned the tab face down and installed the skin. When he turned it over, bam, Netwon Rings...
I never had them before the front screen protector, during the front screen protector install or after the front protector was on the Tab.
Will it happen to you? I have no idea but from what I have read about the problem it is caused because of the Tab moving/flexing which can be caused by excessive heat and certain handling of the Tab.
thanks!
Raistlin1 said:
I blame the install of the rear skin because I had the screen skin installed first and then three weeks later I had the rear done. He turned the tab face down and installed the skin. When he turned it over, bam, Netwon Rings...
I never had them before the front screen protector, during the front screen protector install or after the front protector was on the Tab.
Will it happen to you? I have no idea but from what I have read about the problem it is caused because of the Tab moving/flexing which can be caused by excessive heat and certain handling of the Tab.
Click to expand...
Click to collapse
Thanks for taking the time to explain the details. Sounds like a warranty kinda thing mebbe. Hope it gets resolved! Mine is on order and I'll watch out for this issue.
Cheers!
slack04 said:
I'd avoid the hard plastic static-type.
Click to expand...
Click to collapse
I bought an anti-glare protector from Cellularbuy on eBay and managed to get it on in one go with no dust at all. The protector fits perfectly and the camera and light sensor holes line up spot on. The anti-glare makes the screen look a little grainy, but I hear that even the Steinhell ones that are many times more expensive have the same problem.
This has been gone over millions of times on each forum here, but here's how I did it:
-Wipe the screen down with a soft cloth and glasses cleaner or isopropyl to get any grease off
-Run the shower in a small bathroom on hot until the room is unbearably steamy
-Put on a hat to keep your hair and head funk from falling on the screen
-Line the protector up on the screen before removing the film and tape it on one side with a few pieces of Scotch tape
-Also make a "handle" out of tape to put on the top of the protector opposite the taped-down end. This will help with alignment
-Go into the bathroom and clean the screen with a good microfiber cloth. Also clean the front and back protective sheets on the film so there's no dust to come off when you start peeling them. The steam should be enough to wet it. Take one final look
-Peel the protector back and lay it down pulling the taped edge taut to keep it lined up
-Smooth any bubbles out with a credit card BEFORE peeling the top sheet off
IF you do have any dust, use a piece of tape on a corner to lift up the protector and another piece of tape to pick up the dust. If the room is steamy enough and you did a good job of wiping the screen this shouldn't happen.
I am considering switching from the LG G2 to a N5, and I wanted to get some opinions on the matter. I have scoured the internet(including xda) for hours, and I keep getting wildly varying reports from different sources. My concern is that the N5 is very easily scratched.
https://productforums.google.com/forum/#!topic/nexus/WBQyoSwdQTw
I used a screen protector on the Photon before saying "screw it" and going naked, and I've used the G2 naked for 5 months. Both screens are still in pristine condition, despite being older revisions of Gorilla Glass(GG1 and GG2, respectively).
My concern is that the N5 is for some reason abnormally easy to scratch. I baby my phones a bit, but not excessively(I put it in a separate pocket with the glass to my thigh, I try not to beat the thing with my finger, nothing crazy...). I figure with the fact that I work in some pretty dusty climates, if dust/sand were an issue, my G2 would be far from pristine. I enjoy the naked feeling, but I'm not sure I feel right purchasing a $40 Tempered Glass protector(that I may need to replace a few times over a year, plus it appears to be a struggle to apply with the fact that the display has a dimple in it). Even though I won't use plastic again, it was nice when it got scratched because it was a few bucks to replace, not 10-15% the cost of the whole phone.
So basically my question is to the people rolling naked(well that sounds wrong...), what are your experiences? I really don't agree with protectors, but my OCD doesn't agree with tiny scratches. Thanks!
I roll naked.
I also don't use a screen protector
I've had my N5 since launch day. I would say I "baby" my phone in that I don't do anything with it that is particularly hard on it. If I shine a flashlight on it or have it outside on a sunny day I can see a few "microscratches" that reflect light but are completely smooth to the touch. Apart from that I don't notice anything, even under bright fluorescent lights in my office.
I don't know why this gets brought up so much. If you're worried so much about scratches then get a protector. If you don't like plastic then get glass... You'll wish you did after replacing several plastic ones. The issues you bring up regarding the glass ones and the dimple on the screen has been long fixed and is no longer an issue. Just spend $35 for a Spigen or ~$20 for a Nillkin glass screen protector and be done with it. Its hardly a waste of money and the protectors are more durable than the actual screen.
You dont really need a screen protector but I have an Invisible Shield on mine and its great, I have one really dense scratch on it that you can only see when the screen is on and you look carefully, that will go away when I peel it off. If you are buying a screen protector make sure it goes with the case you get, some cases might peel off the edges of your protector and ruin it.
Dont really think a screen protector is necessary. I have not used one on my old Note 2 or my htc evo before that. N5 has GG3 which does make it a more scratch resistant. Not running a screen protector
I like the HD clear screen protectors by Halo. They have the best edge to edge protection compared to several others that I have tried on my N5. Amazon link - http://goo.gl/hU0NPg
iloome flex. All I have to say.
People say you dont need it, until you **** up your screen, looking at my screen right now, its got some fat scratches, except it doesn't, cause the scratches are on the screen protector.
If there's any chance you could get sand or dust in your pocket at any time GET A SCREEN PROTECTOR!
It only took a really small amount of dirt/sand getting in my pocket during a camping trip to hammer my first N5 with scratches.
Tempered glass is great option, u will avoid both scratches and have better protection for the screen in case u drop it, which I do, not often but occasionally
I use MediaDevil Magicscreen Screen Protector on my Nexus 5 http://www.amazon.co.uk/gp/product/B00GCG3MY2/ref=oh_details_o06_s00_i00?ie=UTF8&psc=1
I bought the Spigen Case Slim for the N5 and it came with a free screen protector!!! It works like a charm, for the price of the two, £7 it was a bargain!!! The screen protector is very good also...
It's very clear and your finger doesn't get stuck by no means...
While GG3 is more scratch resistant to keys/knives, I believe it's not more resistant to dust which is the biggest issue when it comes to scratches. My first N5 I didn't have a screen protector on it because I ended up RMA'ing it. It already had some micro-scratches. Again, you can't feel them and barely see them unless you look for them but they're still there so it depends on how much you care about that. I also keep my phone by itself in my pocket with the screen to my leg and they still happen because of the dust. I've been using a screen protector ever since I received the 2nd phone.
This is one slippery mofo. Any skins out there? Less than 24 hours and this thing keeps slipping off what I thought were flat level surfaces. If I set it flat on the palm of my hand or on a newspaper on a table, I can watch it slowly inch its way to its doom.
I hate to admit I fell for this line from LG:
MIL-STD-810G Method 516.6, Procedure IV “Transit Drop”)Shock Resistant
Compliant with a military standards test (MIL-STD-810G Method 516.6, Procedure IV “Transit Drop”). Device may not perform as tested in all conditions. Test performed in controlled environment. Do not attempt.
Click to expand...
Click to collapse
But if you actually look up what this means... you see its pure and simple marketing buII**** as your "controlled environment" can consist of a careful 4 foot drop onto plywood.
So yes.. skins to keep this thing from slipping are needed.
I ordered the Invisible Phone Guard front/back and will show how it works here when it is received. ATT was supposed to give me a screen protector.
I attached a picture to show what happened here. This is from 2 or 3 falls only 2'5" drop onto a laminate floor. The scratches cannot be seen without good light and the photos were taken using a DSLR and macro lens.. so it isn't terrible, but rest assured this has weakened the gorilla glass and the front screen will eventually shatter if it keeps jumping off tables.
From dbrand
Robot 077 (dbrand)
Apr 13, 15:55 EDT
Hey ######!
Thanks for reaching out. Unfortunately, we have no plans to support the LG G8 ThinQ, as there is simply not enough demand to justify adding it to our portfolio at this time. Sorry about that. Let us know if there is anything else we can help with, and have a great day!
Signed,
A Robot
Click to expand...
Click to collapse
screen protector
https://www.youtube.com/watch?v=9EDYQG6Q7JY
i found this to be a good review of the BodyGuardz Pure Arc Curved Tempered Glass Screen Protector for the G8 ThinQ
i thought it was a shill channel looking at other reviews, but he seems to hate this. it fits GREAT, but only has adhesives on the sides and has a visible dot matrix.
on top of that, he says there is an unnatural hollow feel to it due to the adhesive not being full screen. i imagine this will negatively affect the oled speaker.
this is a $50 screen protector that AT&T is giving away as a part of a promotion.
skins... not much out there and only dbrand has responded (with a NEVER).
the Invisible Phone Guard screen protector was OK and visibility was good, but i found the sound to be very slightly muffled as if it is dampening a certain high frequency.
i'm keeping the back on until i find a decent skin.
this film seems like it will blemish easily. it certainly gets dirty easily. pics here...
Having this phone for a few days now and the OP was not lying about how slippery this phone is. A case or skin is a definite must have!
Ordered a Ringke Fusion X.
Sent from my LM-G820 using Tapatalk
I ordered this case - https://www.ebay.com/itm/273759783563 - I should be getting it later today, I'll post about how well it works.
No sooner did I post this than it came in the mail. Fits on easy, stays on snugly. It's matte rubber without feeling like you're holding a car tire. I had one for my Nexus 6P I really liked and this feels equally good.
This thing is indeed incredibly slippery. I think I'm just going to be extra careful about where I put it down (it's not too slippery in my hands I find, just on certain surfaces), I hate hiding the slick design of the phone with a case. This is also the first phone I've had in a very long time where the camera doesn't bulge out the back, which I really appreciate and don't want to diminish with a case.
doblebo said:
This is one slippery mofo. Any skins out there? Less than 24 hours and this thing keeps slipping off what I thought were flat level surfaces. If I set it flat on the palm of my hand or on a newspaper on a table, I can watch it slowly inch its way to its doom.
I hate to admit I fell for this line from LG:
But if you actually look up what this means... you see its pure and simple marketing buII**** as your "controlled environment" can consist of a careful 4 foot drop onto plywood.
So yes.. skins to keep this thing from slipping are needed.
I ordered the Invisible Phone Guard front/back and will show how it works here when it is received. ATT was supposed to give me a screen protector.
I attached a picture to show what happened here. This is from 2 or 3 falls only 2'5" drop onto a laminate floor. The scratches cannot be seen without good light and the photos were taken using a DSLR and macro lens.. so it isn't terrible, but rest assured this has weakened the gorilla glass and the front screen will eventually shatter if it keeps jumping off tables.
Click to expand...
Click to collapse
Well there are a number of skins now at the varies skin sites though I personally skipped them and simply put the phone into an Otterbox Defender case.
I used a cheap curved glass screen protector ( was like $9) and some loca glue (like $10) to make a DIY full adhesive whitestone kit.
hey everyone - just got my lg g8 a few days ago. i got my case and glass screen protector yesterday. in my head i feel like maybe the screen protector is 'muting' the sound from the screen. has anyone else noticed this, or is it just in my head?
stamos*bp said:
hey everyone - just got my lg g8 a few days ago. i got my case and glass screen protector yesterday. in my head i feel like maybe the screen protector is 'muting' the sound from the screen. has anyone else noticed this, or is it just in my head?
Click to expand...
Click to collapse
I have not had that issue and I am using a Supershieldz screen protector however my brother who is using an Iphone 7 recently had that issue with one due to a screen protector he picked up at Walmart though it resolved once he removed it.
It's amazing to watch this phone slowly creep off of my wireless charger, which has a rubbery grippy surface! My case arrives today...
I'm using slickwraps for the back of my phone and I like it. I would say they are slightly less precise than dbrand, but still great quality. If people would like photos, please let me know.
I'm using a Nillkin slim case, adds no bulk and provides some grippiness.
I also have a Spigen Crystal Clear gel case that's very nice, but is more bulky than the Nillkin.
As for screen protectors, i've found that glass ones are useless for this phone. I tried a couple full adhesive brands with the idea that i would fill the little gap on the edges with LOCA but of the 6 protectors that i applied, they all had a problem sticking fully in some flat areas of the screen. It was always the exact same spots so I came to the conclusion that the LG screen itself isn't 100% flat in those areas so I settled on the Ringke Dual Easy Film screen protector.
Huge Thanks!
Weston
You may want to think about giving the Skinomi Full Body Skin a try. It definitely keeps my phone from slipping off of surfaces, giving the phone a bit of a plastic-rubber feel while still letting the beauty of the phone show through. The back protector doesn't interfere with any cases and offers a bit of mental relief for those times you want to carry your phone without a case.
Dude, I had my g8 for 2 days. Was in. The washroom and the phone was on a roll of toilet paper (the flat side, obviously haha) and got a notification. Before I knew it the phone slid off and landed on the bottom right corner, heard an alarming "tink" sound but didn't think anything of it. A few mins later I saw a small crack, then I looked again and realized that there were multiple cracks on the screen. Ended up getting it replaced by my carrier, I said it was damaged in shipping. Point is that this phone is a glass cannon: it's very powerful for specs but it will have a broken screen if you sneeze on it the wrong way. This is one of the massive downsides to the new gorilla glass. Sure it's scratch resistant but with the wrong amount of pressure it will get destroyed :/
doblebo said:
This is one slippery mofo. Any skins out there? Less than 24 hours and this thing keeps slipping off what I thought were flat level surfaces. If I set it flat on the palm of my hand or on a newspaper on a table, I can watch it slowly inch its way to its doom.
I hate to admit I fell for this line from LG:
But if you actually look up what this means... you see its pure and simple marketing buII**** as your "controlled environment" can consist of a careful 4 foot drop onto plywood.
So yes.. skins to keep this thing from slipping are needed.
I ordered the Invisible Phone Guard front/back and will show how it works here when it is received. ATT was supposed to give me a screen protector.
I attached a picture to show what happened here. This is from 2 or 3 falls only 2'5" drop onto a laminate floor. The scratches cannot be seen without good light and the photos were taken using a DSLR and macro lens.. so it isn't terrible, but rest assured this has weakened the gorilla glass and the front screen will eventually shatter if it keeps jumping off tables.
Click to expand...
Click to collapse
I've dropped this thing so many times because it's so slippery. Seems like every other week I hear it jump off a table a few minutes after I leave the room.
I have a crack on 3 corners, but nothing across the screen. My case (which I tend to take off when connecting it to things such as controllers or some USB cables) almost hides the cracks.
However, these are more like small missing chunks of glass on the corners. I've never had such a fragile phone. I tried super glue on the corners to keep it from spreading, but eventually just went to town on the corners with silicone conformal coating that I had sitting around. It seems to be working great and keeps the little shards coated and sort of glued in there. I kind of prefer this to replacing the screen as replacements have only gone down slightly to around $150 shipped from China and I know I'll just end up breaking that one.
There's always been one or two deal breakers with all of my LG phones and that's why I kept going to a different manufacturer as soon as I could. I hate to say it but after this, I'm never going back to LG again no matter what cool unique feature they're wooing me with.
I basically used this phone with a broken screen for 5 months. Replacements are still $150 (better than $200 back when it broke). It dropped approximately 1.5ft face down onto a clay tile floor and front screen has cracks all over. It almost looks somewhat inverted now as if the screen was designed to have tension. Well I went and got a note 10+ and man it is great to have a real phone again. Doesn't have some of the edgy LG stuff that I really loved and theres no headphone jack... but bigger/brighter screen that isn't broken is so nice to have. Good luck with your screens guys.... I'll replace mine when the price is reasonable and either go back to using it or put it on ebay.
Jaa-Yoo said:
I'm using a Nillkin slim case, adds no bulk and provides some grippiness.
I also have a Spigen Crystal Clear gel case that's very nice, but is more bulky than the Nillkin.
As for screen protectors, i've found that glass ones are useless for this phone. I tried a couple full adhesive brands with the idea that i would fill the little gap on the edges with LOCA but of the 6 protectors that i applied, they all had a problem sticking fully in some flat areas of the screen. It was always the exact same spots so I came to the conclusion that the LG screen itself isn't 100% flat in those areas so I settled on the Ringke Dual Easy Film screen protector.
Click to expand...
Click to collapse
I have reached the same conclusion about the screen not being flat enough to utilize a hard glass protector even if you avoid the very curved edge portions. I tried the curved, glued only on the edge types first but that always had a weird optical effect and wasn't very ruggedly glued on, none in the middle. Why? I haven't tried using whitestone glue yet.
So the suggested one sounds interesting. https://www.amazon.com/Ringke-Compa...dge-Application/dp/B07NHMBNLH#customerReviews
I think I'll watch the videos first.
I also found these but yes a firm, solid piece of glass is a no go IMHO. Not a fan of these new case designs for all the new phones. Why de do dat?
https://www.amazon.com/dp/B07QQD2BCG/ref=cm_sw_r_cp_apa_i_MkrHDb48GTKZN
https://www.amazon.com/gp/product/B07QB9MN28/
Still hoping for a solution. I had great luck with Spigen Crystal screen protector SGP10855 for my LG G3 which is hard but I believe would be flexible enough if it skipped the curved edges but they don't make anything like that?
UPDATE: After watching the LG G8 video on YouTube I decided to go with the Rinke.
I'll report back. This will be 4th type attempted.
I put it on this morning. It is pretty easy to get this on with good alignment and no bubbles.
Two things.
1. If you watch the YouTube instructions the place where the dust dust cleaning sticky backing splits in half does leave a slightly perceptable crease in the soft protector. Maybe it will smooth out with time? It did not with the squeegee.
2. It's soft so you can possibly nick with your fingernails and it's also easy to lift an edge ever so slightly during final finishing so be careful.
I see no installation flaws but it also isn't a hard glass but then those do not install properly even when undersized because the screen is not level as you get near the edges as far as 1/4" away. The film eliminates this issue but will it protect and stay on.
We shall see.
I sell a lot of these devices and it is even hard to photograph them on a smooth surface because they will start around on my table. Put it in a case, the screens are expensive.