hi
i bought an s4 mini i9195 with fault :
"
ODIN MODE
PRODUCT NAME : GT-I9195
CURRENT BINARY : Custom
SYSTEM STATUS fficial
KNOX KERNEL LOCK :0X0
KNOX WARRANTY VOID :0X1
CSB-CONFIG-LSB :0X30
BOOTLOADER RP SWREV:2
WRITE PROTECTION :ENABLE
Firmware upgrade encountered an issue. Please selectect recovery mode in kies & try again"
when i flash pit file this message dispair and i've logo stuck with "set warranty bit kernel"
i can going to download mode vol- + home + power
but can't enter recovry mode vol+ + home + power it show " recovery booting ... set warranty bit recovery"
i've try de restore with many official rom up to the lastest rom.
with the lastest rom odin freeze on boot.img and take message "ODIN flash write failure "
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> FAIL! (Write)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i tested with 4 file rom and odin stuck on aboot.img
all tested on many pc with many usb cable
what solution? is the hardware problem (emmc)
thx
Try to enter Download mod, and Cancel (volume down). Worked for me on I9195
Related
Hello People,
I have a samsung galaxy s4 mini GT-I9195, whenever i turn it on :
Image size too large!! W:1080, H:1920
display image fail
SECURE FAIL: KERNEL
message is shown, I download couple of firmwares and tried to flash it but none of them worked.
Here's the Odin's log
#####################################################################
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
##################################################################
And the sad part is i can't even access the recovery mode, whenever i try to access recovery mode it shows me the above's error. Can you people please help me fix this?
Here's what it shows on Odin Mode:
Product name: GT-I9195
Current Binary: Samsung Official
System Status: Official
Knox kernel Lock : 0*fffffffc
Knox warranty Void: 0*fffffffc
CSB-CONFIG-LSB: 0*30
Bootloader AP Swrev :2
Write Protection : Enable
SW REV CHECK FAIL: Fused 2> Binary 1
same here
akamurdera said:
Hello People,
I have a samsung galaxy s4 mini GT-I9195, whenever i turn it on :
Image size too large!! W:1080, H:1920
display image fail
SECURE FAIL: KERNEL
message is shown, I download couple of firmwares and tried to flash it but none of them worked.
Here's the Odin's log
#####################################################################
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
##################################################################
And the sad part is i can't even access the recovery mode, whenever i try to access recovery mode it shows me the above's error. Can you people please help me fix this?
Here's what it shows on Odin Mode:
Product name: GT-I9195
Current Binary: Samsung Official
System Status: Official
Knox kernel Lock : 0*fffffffc
Knox warranty Void: 0*fffffffc
CSB-CONFIG-LSB: 0*30
Bootloader AP Swrev :2
Write Protection : Enable
SW REV CHECK FAIL: Fused 2> Binary 1
Click to expand...
Click to collapse
Have exactly the same problem. Did you fix it in the meantime?
Bart
Bartoos-48 said:
Have exactly the same problem. Did you fix it in the meantime?
Bart
Click to expand...
Click to collapse
Me too... Help please...!!!
fixed it
In the meantime I have been able to fix my problem.
Installed recovery-clockwork 4.6.0.6 via Odin (grabbed it from http://forum.xda-developers.com/showthread.php?t=2364980 )
Running the recovery brought my phone back to life , and checking the settings 4,4,2 was installed!
Hope this helps you as well.
Bartoos-48 said:
In the meantime I have been able to fix my problem.
Installed recovery-clockwork 4.6.0.6 via Odin (grabbed it from http://forum.xda-developers.com/showthread.php?t=2364980 )
Running the recovery brought my phone back to life , and checking the settings 4,4,2 was installed!
Hope this helps you as well.
Click to expand...
Click to collapse
That procedure is only valid for GT-I9190 not for GT-I9195.
Bartoos-48 said:
Have exactly the same problem. Did you fix it in the meantime?
Bart
Click to expand...
Click to collapse
No success at all. :/ Anyone around please help
akamurdera said:
That procedure is only valid for GT-I9190 not for GT-I9195.
Click to expand...
Click to collapse
Lucky my GT-I9195 didn't know that. Because it certainly worked for me.
Can you tell me how did you fix it? in your own words.
Hello, I am trying to install stock firmware on my note 4. I think I downloaded the correct firmware, but I am not technologically savvy and when I try to use Odin, I receive this error:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
can someone please help me??
glopez12323 said:
Hello, I am trying to install stock firmware on my note 4. I think I downloaded the correct firmware, but I am not technologically savvy and when I try to use Odin, I receive this error:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
can someone please help me??
Click to expand...
Click to collapse
On what firmware are you and what firmware did you download? Did you tried different version of ODIN?
Clicking from the Edge of Galaxy
norbarb said:
On what firmware are you and what firmware did you download? Did you tried different version of ODIN?
Clicking from the Edge of Galaxy
Click to expand...
Click to collapse
My phone was on 6.0.1 but I could not find the right firmware online so I tried to downgrade. Is that possible? And yes, I tried different versions of Odin :/
glopez12323 said:
My phone was on 6.0.1 but I could not find the right firmware online so I tried to downgrade. Is that possible? And yes, I tried different versions of Odin :/
Click to expand...
Click to collapse
When you go to settings ->about device what is your baseband version?
Clicking from the Edge of Galaxy
Unfortunately I do not have access to my phone anymore menus anymore. I can only access download mode and emergency recovery screen.
glopez12323 said:
Unfortunately I do not have access to my phone anymore menus anymore. I can only access download mode and emergency recovery screen.
Click to expand...
Click to collapse
In THIS THREAD is firmware EPH5 and ODIN witch worked on so many phones. Try this.
I have an AT&T Note 10+, N975U1. I tried to flash a US unlocked firmware onto it, but that kinda didn't work... Now I'm stuck on this page that says " An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software". I tried smart switch, but it wouldn't recognize my phone in the emergency recovery. I decided to try to flash the ATT firmware, thinking that doing this might fix it, well not really, I'm stuck and I have no clue what I'm supposed to do.
Log:
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> skip file list for home binary
<ID:0/003> quest.fv
<ID:0/003> persist.img.ext4
<ID:0/003> userdata.img
<ID:0/003> carrier.img.ext4
<ID:0/003> dqmdbg.img.ext4
<ID:0/003> Home Binary Download
<ID:0/003> Total Binary size: 8720 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> abl.elf
<ID:0/003> xbl.elf
<ID:0/003> xbl_config.elf
<ID:0/003> tz.mbn
<ID:0/003> hyp.mbn
<ID:0/003> devcfg.mbn
<ID:0/003> aop.mbn
<ID:0/003> bksecapp.mbn
<ID:0/003> cmnlib.mbn
<ID:0/003> cmnlib64.mbn
<ID:0/003> km4.mbn
<ID:0/003> qupv3fw.elf
<ID:0/003> sec.elf
<ID:0/003> apdp.mbn
<ID:0/003> msadp.mbn
<ID:0/003> storsec.mbn
<ID:0/003> uefi_sec.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> multi_image.mbn
<ID:0/003> dspso.bin
<ID:0/003> vbmeta.img
<ID:0/003> vaultkeeper.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> vendor.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> dtbo.img
<ID:0/003> vbmeta.img
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img.ext4
<ID:0/003> product.img.ext4
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
EnderGopo said:
I have an AT&T Note 10+, N975U1. I tried to flash a US unlocked firmware onto it, but that kinda didn't work... Now I'm stuck on this page that says " An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software". I tried smart switch, but it wouldn't recognize my phone in the emergency recovery. I decided to try to flash the ATT firmware, thinking that doing this might fix it, well not really, I'm stuck and I have no clue what I'm supposed to do.
Log:
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> skip file list for home binary
<ID:0/003> quest.fv
<ID:0/003> persist.img.ext4
<ID:0/003> userdata.img
<ID:0/003> carrier.img.ext4
<ID:0/003> dqmdbg.img.ext4
<ID:0/003> Home Binary Download
<ID:0/003> Total Binary size: 8720 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> abl.elf
<ID:0/003> xbl.elf
<ID:0/003> xbl_config.elf
<ID:0/003> tz.mbn
<ID:0/003> hyp.mbn
<ID:0/003> devcfg.mbn
<ID:0/003> aop.mbn
<ID:0/003> bksecapp.mbn
<ID:0/003> cmnlib.mbn
<ID:0/003> cmnlib64.mbn
<ID:0/003> km4.mbn
<ID:0/003> qupv3fw.elf
<ID:0/003> sec.elf
<ID:0/003> apdp.mbn
<ID:0/003> msadp.mbn
<ID:0/003> storsec.mbn
<ID:0/003> uefi_sec.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> multi_image.mbn
<ID:0/003> dspso.bin
<ID:0/003> vbmeta.img
<ID:0/003> vaultkeeper.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> vendor.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> dtbo.img
<ID:0/003> vbmeta.img
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img.ext4
<ID:0/003> product.img.ext4
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
You need to download the firmware you had before or you can flash again the same code but use CSC (Not HOME_CSC) and restore everything after. The trick is to get back to the download screen, and for that you need quick hands, and here is how...
Hold the power button and volume down for 7 seconds or so, as soon as the phone resets leave the buttons and hold the volume up button. You will be back to the download mode. Ignore the red exclamation mark on the screen. Flash away and you will be fine. You can't go from U to U1 or vice versa and keep your original partition. HOME_CSC can not be used in that case.
BigE said:
You need to download the firmware you had before or you can flash again the same code but use CSC (Not HOME_CSC) and restore everything after. The trick is to get back to the download screen, and for that you need quick hands, and here is how...
Hold the power button and volume down for 7 seconds or so, as soon as the phone resets leave the buttons and hold the volume up button. You will be back to the download mode. Ignore the red exclamation mark on the screen. Flash away and you will be fine. You can't go from U to U1 or vice versa and keep your original partition. HOME_CSC can not be used in that case.
Click to expand...
Click to collapse
OMG I have no way of thanking you, it really sucks that I lost all my information since I don't have a backup of it, I'll definitely change that ASAP. Thanks for this, and have a great day!
I had same problem last night. My samsung note 10 plus got stocked on "an error has occured while updating the device software" .
Initially, I tried using home csc but it got stuck on same page. I then decided to use csc and still got stucked too. Phone Battery is drained and I ave no idea wat to do.phone brand is AT&T unlocked version in Nigeria. I don't know of the Odin version used is the problem but I used the same Odin version to update my samsung Note 8 & there was no problem. Pls help!!!
---------- Post added at 09:17 AM ---------- Previous post was at 08:22 AM ----------
I tried flashing it again with odin and phone still not entering download mode bt I got info somewhere here that flashing of firmware can still occur if stocked on the error screen. The process was moving and after a period of time. Odin wrote failed. Wat to do now???
The firmware am updating to is N975USQU3CTE7.
Or am I using the wrong firmware???
DEREK1414 said:
I had same problem last night. My samsung note 10 plus got stocked on "an error has occured while updating the device software" .
Initially, I tried using home csc but it got stuck on same page. I then decided to use csc and still got stucked too. Phone Battery is drained and I ave no idea wat to do.phone brand is AT&T unlocked version in Nigeria. I don't know of the Odin version used is the problem but I used the same Odin version to update my samsung Note 8 & there was no problem. Pls help!!!
---------- Post added at 09:17 AM ---------- Previous post was at 08:22 AM ----------
I tried flashing it again with odin and phone still not entering download mode bt I got info somewhere here that flashing of firmware can still occur if stocked on the error screen. The process was moving and after a period of time. Odin wrote failed. Wat to do now???
The firmware am updating to is N975USQU3CTE7.
Or am I using the wrong firmware???
Click to expand...
Click to collapse
In order to go to download mode , when phone is on and stuck (telling you to use Samsung switch), you want to take the following steps:
1. Restart the phone: push power button and volume down for 7 to 13 seconds. Phone will start a reboot.
2. Now comes a quick hand feature... As soon as the screen changes to the Samsung logo, lift your finger from the power button, keep the volume down pushed, and add a volume up button.
3. You will end up in the download mode window. Ignore the scary red exclamation character, use Odin with the right firmware. Flash the full ROM , not just CSC .
4. Restore your phone, as you will have a fresh new start.
One word of warning. If you flash the user data of your carrier, you better remember your PIN code. The phone is set to identify a factory reset as a potential 'theft attempt'
Good luck
i am having a similar problem. i can reboot the phone from the exclamation point screen to the initial download mode screen. then, i have to push the volume up key to continue, and it goes right back to the smart switch screen. stuck in a loop. can anyone help?
agc87 said:
i am having a similar problem. i can reboot the phone from the exclamation point screen to the initial download mode screen. then, i have to push the volume up key to continue, and it goes right back to the smart switch screen. stuck in a loop. can anyone help?
Click to expand...
Click to collapse
Disconnect the USB cable when you reboot and get to the download screen, if you are keeping it inserted. If you do not, I have no clue why is dies it..
EnderGopo said:
I have an AT&T Note 10+, N975U1. I tried to flash a US unlocked firmware onto it, but that kinda didn't work... Now I'm stuck on this page that says " An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software". I tried smart switch, but it wouldn't recognize my phone in the emergency recovery. I decided to try to flash the ATT firmware, thinking that doing this might fix it, well not really, I'm stuck and I have no clue what I'm supposed to do.
Log:
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> skip file list for home binary
<ID:0/003> quest.fv
<ID:0/003> persist.img.ext4
<ID:0/003> userdata.img
<ID:0/003> carrier.img.ext4
<ID:0/003> dqmdbg.img.ext4
<ID:0/003> Home Binary Download
<ID:0/003> Total Binary size: 8720 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> abl.elf
<ID:0/003> xbl.elf
<ID:0/003> xbl_config.elf
<ID:0/003> tz.mbn
<ID:0/003> hyp.mbn
<ID:0/003> devcfg.mbn
<ID:0/003> aop.mbn
<ID:0/003> bksecapp.mbn
<ID:0/003> cmnlib.mbn
<ID:0/003> cmnlib64.mbn
<ID:0/003> km4.mbn
<ID:0/003> qupv3fw.elf
<ID:0/003> sec.elf
<ID:0/003> apdp.mbn
<ID:0/003> msadp.mbn
<ID:0/003> storsec.mbn
<ID:0/003> uefi_sec.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> multi_image.mbn
<ID:0/003> dspso.bin
<ID:0/003> vbmeta.img
<ID:0/003> vaultkeeper.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> vendor.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> dtbo.img
<ID:0/003> vbmeta.img
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img.ext4
<ID:0/003> product.img.ext4
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Hey mate, I am also getting same error while trying to Flash Note 10+ firmware from BRI to TGY. Did you resolve this issue? I want to flash TGY firmware on SM-N9750 but getting this error so I had to revert to BRI firmware again.
I did put my Samsung Galaxy Tab 3 Lite SM-110 to charge and suddenly he begins a kind of boot loop.
Note: I did try so many things and had no way to me enter in the hard reset menu or in recovery mode(it is impossible by pressing buttons(believe me I tried every combination existing))
Note 2: The unique access possible is by download mode then, give me some solution that is by download mode.
Note 3: I did discover T110XXUANG2 is my PDA number based on the buy date 08/2014
Note 4: I did try every single one rom of my device(it had 5 based on my country) in each field(BL, AP, CP, CSC) and each one returns me the same error:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> timh.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> obm.bin
<ID:0/003> DTim.Recovery
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Note 5: I did try to remove the DTim.Recovery of the rom with the 7zip but, when I remove it appears other error of another file and when I remove another one appears another one and that continue until over every file in the rom.
What checkboxes do you press in Odin?
Hello, I need to bypass FRP since my sister-in-law somehow got locked out from her Google account
Firmware version is A520FXXSFCTG8
I tried to use combination file method but when flashing back to A520FXXSFCTG8 it fails on hidden.img
Code:
<ID:0/003> Home Binary Download
<ID:0/003> Total Binary size: 4586 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
what I should do?