Hi guys, i have an issue...my phone dropped in water...everything is working fine (i swapped components with another phone) but not the charging part...battery is good...
disassembled the phone, in the pcb under the metallic plate there is a burned component...i have a friend that can replace it but i need the schematics of the motherboard to choose the right component (voltage, power ...)...i can't find online a schematic of the motherboard, can you guys help me ?
the problem is that phone won't charge, it gets power (with tester i can see it) but phone olny turns on for a second and then shutdown...i think the component is a power regulator or something like that
ps. sorry for bad english
Since you dropped it into water it's big chance that much more parts are screewed. I suggest you to disassemble phone and look to motherboard an electric parts are they rusty, rust will be white color if there is a lot of that than you shouldn't fix that part because a lot of stuff is broken or will break soon. You can try placing phone in supersonic bathtub but that won't help for long time in most cases. If your friend can replace part than he should know how to find that part if he have knoweledge in that area.
don't worry, the other parts work good...i swapped all parts (lcd, speaker, touch and more) with another motherboard and everything working fine...after i dropped in the water i cleaned the phone without turning on from everything...the only damaged part is that chip (burned) under the metallic plate...the rest is clean as new and working...if i can identify that chip (o what the hell is it) a friend of mine can replace it
Well, I doubt you will find scheme anywhere online. What you can do is to post picture of that part which is broken/burned and post picture to some forum for electronics maybe someone will recognize it.
Hey, is this (https://goo.gl/qMGcmV) what you're looking for?
i don't have the phone right now, i asked my friend for a picture but still no answer
thank you but no...i'm looking for the schematics of the motherboard...i'm putting a picture of the damaged component
Related
Hey guys-- got back from the t-mobile store and they told me the data port is dead (from water damage). It turns on with a fresh battery fine, but apparently I'm getting an error code. That code is probably that the data port is messed up because I can't charge my battery. I'm assuming I have to replace it. Does anyone know of a video tutorial or something that will show me how to do it?
thanks.
the chances of the data port being physically damaged by water is very slim- I think they are trying to tell you the circuitry is faulty. If you had ripped the charger out and bent or broke the port, then I could see it- but water cannot bend or break that way and corrosion is unlikely unless its been sitting a while.
Back to the original subject though, I just replaced a faulty USB port on my friends Moto Q. It wasnt bad, but you need a very small pencil iron (I use a station) and good eyes, otherwise you will bridge the tiny connections and be fubar'd.
gospeed.racer said:
the chances of the data port being physically damaged by water is very slim- I think they are trying to tell you the circuitry is faulty. If you had ripped the charger out and bent or broke the port, then I could see it- but water cannot bend or break that way and corrosion is unlikely unless its been sitting a while.
Back to the original subject though, I just replaced a faulty USB port on my friends Moto Q. It wasnt bad, but you need a very small pencil iron (I use a station) and good eyes, otherwise you will bridge the tiny connections and be fubar'd.
Click to expand...
Click to collapse
Where did you find the port to replace it with...
find a bricked one on ebay or something..or someone selling one with a cracked screen etc...use it for parts
welp, i've never soldered... guess you gotta learn sometime. ports are bout 25 bucks... Guess I have a new hobby. Or maybe I should just buy an external battery charger... soldering sounds more fun though. Yeah, what i meant by getting an error code is when i plug in the charging cord into the cell phone, I get a red light instead of yellow/orange. But, I have to push up on the cable where i insert it into the port to get anything. So, its not dead, but either dying or drunk....... drunk from oil.... which it swam in... and got sick from. vegetable oil, not motor oil... which would be a waste of oil. Anyways, thanks for the replies and if you stumble upon a vid for the dash, please post it. I found some on blackberries, but not an excaliber.
sorry browser problem (double posted)
my friend sourced his usb port from Mouser (P/N 538-67503-1020) for $1.12 each. I still have one (he got a spare) but I dont have a dash to take apart and compare the pins. I assume they are all the same generic port, but the pin spacing could differ
http://www.mouser.com/Search/ProductDetail.aspx?qs=7zcQ9RRVJlhHWuXYKEhKMg==
that's pretty sweet speed. I bookmarked that webpage (dunno why really). I could just always link from here; but anyway, I received a new battery that I ordered before the geniouses at t-mobile told me that a red light is an error code, my old battery is perfectly fine, my data port is broken, and no... a new battery won't fix it. *** what's my point you ask?***
They don't know jack fecal matter. I just popped in the new battery and 1) my phone turned on, 2) my charging light turned orange, 3) my plug doesn't need adjusting to charge the phone, and just now 4) my phone has signaled to my through a pretty green light that the new battery just finished charging.
So, to recap, the guys at t-mobile said my port was fried and that all my problems were due to that. My theory was that oil (and come to find out water) damage caused the battery to malfunction and thereby refused to allow a current to charge it resulting in the errors. Turns out, I was right.
Thanks speed and all for your replies. If I need a cheap miniusb port in the future, I now have a good source. Now, Anyone know if a new lcd will fix the splotchy marks on my screen (look like dark puddle spots). I'll post a pic in a new post in a minute.
Yah you can grab a new LCD off ebay (fairly cheap) and then go to youtube and youtube "fix dash screen" and there is a tutorial on there that will guide you on replacing your screen.
just make sure its the lcd thats the problem- the outer clear part that you can touch is separate, and comes with the case. Mine are scratched to hell on both my Dash's but I refuse to buy new cases to fix them
i dunno what's up anymore
I don't know what to think of this thing anymore. This morning it wouldn't turn on, even though I had the green light on the device as it was plugged in all night. So, I kept fiddling with it hoping it would turn on so I could have ATT do a remote hard reset. Well... it wouldn't cooperate. So, I left it alone. Then this evening I was about ready to bury it and I tried the power button one last time and it turned on. But, the battery was really low and I got the red light again when I plugged it in. I guess the battery got a bit of a charge in itself just sitting there. So, perhaps the t-mobile guys do know what they're talking about. Well... i did actually get the orange light while it was on for that sweet minute, which should mean its charging, but I guess its not actually charging the battery. I suppose the last way to go is external charger. I'll probably pick one up off ebay for 15 bucks.
Hello, I saw that someone else asked a similiar question before but they did not word the question correctly and got little help.
On my HTC EVO logic board, there's three tan "ports" (I don't know what they are actually called). One for the front camera, one for the LCD, and one for the front panel.
While walking home one day, my screen started showing a dark spot. The spot got bigger, and I decided to take apart my phone (something I'd done before a few times) and try to clean things up. I put everything back together, and the LCD would not come on. After numerous tries, I finally decided the LCD was damaged. As I went back in the phone, I saw that regardless of whether you flipped the black tab on top of the LCD tan 'port' back or forward, the cable was capable of being pulled out, e.g., it was not secure. At the time, I thought nothing of it, but now that my new LCD should be here, I'm worried.
Is my LCD not working because the 'port' is broken? If so, what can I do to repair it? (I heard it is very difficult). I'm worried, because I paid a lot to buy a new LCD and will be unable to send it back.
http://guide-images.ifixit.net/igi/ZYHLZwIIVhjilEpT.large
Also, my front panel cable never sits 'perfectly'..that is, I have to connect everything else first, and then try my best with the front panel. The tape does not stay down flat completely.
These sorts of connectors can be fixed,but there is quite a bit of skill involved. Upload a picture and I can tell you better how hard it is. What I can tell you is that you probably cant do it yourself. I base this on the fact that those who have the necesesary skils will instantly know its going to be a pain. In fact,its easy to screw it up ,and sometimes you do,even if you DO know what your doing. Since I dont want to take my phone apart,Ill need to see a picture of it before I can tell you anything more. One thing to keep in mind is that sometimes the ribbon cable CAN be pulled out anyway,and is making good contact and there is some other problem. If you have not installed the new LCD,install it and see if it all works. If so,your good to go. As a general rule,the connectors are delicate and its not a good idea to pull them out. In fact,dont disconnect them if you dont have to. They have a limited number of connect/disconects they can take and they are very easy to break.
pflatlyne said:
These sorts of connectors can be fixed,but there is quite a bit of skill involved. Upload a picture and I can tell you better how hard it is. What I can tell you is that you probably cant do it yourself. I base this on the fact that those who have the necesesary skils will instantly know its going to be a pain. In fact,its easy to screw it up ,and sometimes you do,even if you DO know what your doing. Since I dont want to take my phone apart,Ill need to see a picture of it before I can tell you anything more. One thing to keep in mind is that sometimes the ribbon cable CAN be pulled out anyway,and is making good contact and there is some other problem. If you have not installed the new LCD,install it and see if it all works. If so,your good to go. As a general rule,the connectors are delicate and its not a good idea to pull them out. In fact,dont disconnect them if you dont have to. They have a limited number of connect/disconects they can take and they are very easy to break.
Click to expand...
Click to collapse
Well, I don't really have a means of taking a quality photo except with my computer webcam but I'll try in a second. I can't really show you because there isn't much to see. The little black bar that flips up and down to 'lock' the port is ineffective; the cable can be pulled out regardless. I know I can't fix the port/connector by myself, so I'm hoping that's not the issue. You have given me a lot of hope though. The new LCD should be here by Wednesday at the latest, so I'll be able to test it then.
Does my front panel affect the LCD? Since I dropped my phone on the corner, even with a new panel it does not sit 'perfectly'. I don't think they're related though.
BluRngerGurl said:
Well, I don't really have a means of taking a quality photo except with my computer webcam but I'll try in a second. I can't really show you because there isn't much to see. The little black bar that flips up and down to 'lock' the port is ineffective; the cable can be pulled out regardless. I know I can't fix the port/connector by myself, so I'm hoping that's not the issue. You have given me a lot of hope though. The new LCD should be here by Wednesday at the latest, so I'll be able to test it then.
Does my front panel affect the LCD? Since I dropped my phone on the corner, even with a new panel it does not sit 'perfectly'. I don't think they're related though.
Click to expand...
Click to collapse
I dont think so. I bet your ok. Just dont keep playing with the connector. I know,Ive done it. I sit there messing with it,wondering,is it broken? Is it good? Then the little black peice comes off in your hand or the plastic breaks and "well its sure broken now!" Remember,that little latch does not so much hold the cable in place as hold the cable against the contacts,if its making contact,its good to go.
Hi, all. The new LCD I receieved did not work. There are very minor differences in the two; such as some type of blue gunk on the silver part of the LCD, the connector is more of a dark orange on the new one while the original is a yellow-orange, etc. Also, again, the connector does not 100% fit in the slot. It goes in, but a small corner sticks out a bit and you have to either hold it in or clip it in [which I can't, because the black clip is broken].
The only possibilities I can think of are
A] Because the little black thing is damaged, no LCD will work in it. Therefore I need a new phone.
B] The LCD does not work.
C] The LCD is the wrong size.
At this point I want to just give up and get a new phone, which is very heart-wrenching because I love my EVO and I doubt I can afford the only other phone I like, the Samsung Galaxy S II Epic Touch 4G.
Is anyone able to identify what connector is used on this phone for the LCD? I broke a pin on the connector while trying to repair a cracked screen. I would like to buy it and re-solder it on to fix the phone.
Can someone link the correct connector maybe from digikey.com?
Broken latch
I too have a problem with the connector... the plastic part that connects the ribbon cable to the main board has broken. There must be a place to buy these tiny plastic latches... does anyone know? Your assistance will be greatly appreciated!
Mac-
Hello to anyone reading this,
This crack in the board happened after it went through the clothes washer, and it was gf's phone so i feel really horrible about it :crying:.
Anyways i have yet to even find out what this piece of the board is named. It's cracked in two places on the vertical part of the board that leads down
to where the usb connector is located (everything else appears looks ok just these two cracked pieces). I'm just looking for any help at all, hoping
someone might be able to offer any help at all, or if it's even possible to salvage. I have an uncle that is got a good amount of experience in
soldering/electrical stuff and can handle the soldering/fixing since im still a bit of a noob, but he was unsure about how to go about it since it would
require some very small wires to fix the connection traces, so if anyone can offer any advice or instruction on mending i would greatly appreciate and
can send some BTC for your help. I attached 2 images, and can supply more if you need more detail.
So far the only thing i can think of is to get a broken board and remove the part i need at the easiest location it could be re-attached... no clue if that easier area exists though..
Why not just bring the phone to some phone repair shop (or a samsung specialized one), if available in your region. They should be able to repair it (if the price is ok with you), or be able to sell you the part you need (order it).
**It looks like even some chip is chopped... at the very least, probably too much water damage on them. You don't want to do this repair by yourself (or you uncle)... there are cases of phone components getting too hot and on fire if there are faulty wires/connectors.
****Definitely a new board is required.
cyberboob said:
Why not just bring the phone to some phone repair shop (or a samsung specialized one), if available in your region. They should be able to repair it (if the price is ok with you), or be able to sell you the part you need (order it).
**It looks like even some chip is chopped... at the very least, probably too much water damage on them. You don't want to do this repair by yourself (or you uncle)... there are cases of phone components getting too hot and on fire if there are faulty wires/connectors.
****Definitely a new board is required.
Click to expand...
Click to collapse
Yeah seems like a new board might be the only solution..
can anyone tell me what exactly would be compatible? This was a verizon note 2 sch-i605 gt-n7100 rev 1.0.
Thanks all
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Fycola123 said:
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Click to expand...
Click to collapse
Hi,
Only thing I can think of is that somehow it has damaged the cable from the touchscreen or the tiny wires that feed into the cable without damaging the screen. I came across a brand new screen I was replacing once for someone that had a similar problem where the bottom left hand corner wouldn't respond to touch unless there was firm pressure on the screen to create contact, and this was a brand new screen. It could also be that the touchscreen connector needs to be pushed back onto the board if it's come a bit loose.
If this is the problem, you can fix it by yourself although I'd have a good look around youtube, there are heaps of DIY videos of how to replace screens. If you do go down this path I recommend you replace the touchscreen/LCD/LCD frame in one go, as it's generally already pre- assembled the only thing here is that there are 3 brands of LCD's HTC used with the phone and they aren't all compatible, and you can only tell by pulling down your phone and looking at the LCD flex cable colours, and the other thing is that the screens that are available aren't always the same quality as the original. If this sounds to hard your best bet is to take it somewhere and diagnose the problem just in case it's something else
Hi
Sorry for my english, I'm hungarian, this is the best I can do.
So I bought a cheap (but not too cheap) SM-P905, but I can't get the screen to work properly.
The touch layer, the spen, the backlight works well, I managed to mirror the screen on my pc and everything else seems to be okay.
I got off the back cover, I tried to unplug and reattach every flex cable, even the battery. I tried to look everything under magnifying glass to see what could be the problem.
The lcd flex connector looks like this under my lens.
(Upload it in the next post, not working from the android app)
I tried to clean it with a needle, but it still looks like it is corroded or melted.
Is it possible that replacing this connector will get the screen back to normal? (I found flex connector replacement on the internet)
Or is it possible to repair it with some jumpers or something like this?
Is it melted because of some shorted circuit somewhere else, or because of a bad micro capacitor?
How and where can I locate and resolve this problem (s)? Maybe is it still the lcd that is simply dead and I can't bring it back to life?
I dont want to buy a screen, and a motherboard (neither only one of them )
Thank you for your help!
Okay the forum doesnt let me to insert links or photos, because I'm new here -.-
/s/53oab9sykbihn32/20151021_175009.jpg?dl=0 write dropbox dot com in front of link
https://www.dropbox.com/s/53oab9sykbihn32/20151021_175009.jpg?dl=0
In my opinion it died!!
I hoped for better opinions
I wanted to know how this thing can die?
It has to be caused by something.
Bad resistor/capacitor? Is it on the motherboard or on the lcd's circuitboard?? Or is it only the corroded flex connector??
I dont want to throw the whole tablet in the trash. Everything else is just operating fine.
If nobody can answer this, where should I write, where people can help with these very small components / resoldering / measuring what gone wrong here?
Alan-B said:
In my opinion it died!!
Click to expand...
Click to collapse
So today I measured the pins in worst condition. There are 2 pins that I tought can cause the problem and looks corroded. (Number 5 and 9 from the right) Both of them !are not used!. (There is a total of 3 pins that are not used on the connector/cable)
They are not lead through the flex cable, they have no function here.
So the problem comes from somewhere else, but I still don't know why they look like this.
Maybe I will try to seperate the screen from the body and look at it closer and its connectors/smaller circuit boards.
Sent from my SM-N9005 using XDA Free mobile app
Hmm, that pic does not make me think its a corrosion problem. At best, it can lead to a finicky connection, but there seems to be enough there for proper electrical contact. If this were a headphone jack, for example, I would say apply pressure near the cable to see if the headset works properly, and if it does, then I know its a cable problem. No idea if you can try to apply pressure to the cable and see if the LCD turns on.
If the screen mirrors on the TV successfully, then there are a bunch of Samsung Service Codes you can use to test the LCD. Unfortunately I do not know them for this model, but google should get you the service menu very easily. There is definitely a test in there for the LCD that should give you a better idea what to expect.
If the cable is pretty cheap, I would also just pick up one and try replacing. Nothing to lose! AND if you have access to another identical device, you can try to stick this LCD on that device to see if its the LCD thats the problem or the motherboard.
Lastly, I would want to know if the glass on that LCD has ever been replaced. If they did a glass only replacement, its possible they overheated the LCD ... OR used too much LOCA glue that shorted the connectors.
Many possibilities, so I wouldn't call it a day yet. First, look for the service menu, thats the best place to begin.
I will try the service codes.
Unfortunately I don't have more devices. The easiest way would be to test the identical parts on a working one, but I don't know anyone who would risk his/her tablet for this
The other thing I can do is to get another lcd-glass unit from ebay or from ifixit and try it. If the problem was the lcd, it should work, I'm happy, but if its black, I will have (maybe) 2 working lcd units for sale. Or I have to get a new motherboard (sounds expansive).
I don't think that they replaced the glass on this device, it looks very used and scratchy, so it was working before.
Thank you for taking your time for me and answering my dumb questions!!
Sent from my SM-N9005 using XDA Free mobile app
There are more good news than bad, so I'm very happy.
So 1-2 days ago I started to get off the screen to see if I can seperate the LCD from the receiver. Turned out its not that hard. The only hard thing is to get it off the body in one piece. Lots of heating with a hair drier, and a LOT OF PATIENCE. If you can get it off in one piece you are on your way.
Seperating the glass from the LCD is very easy, did it in 10 minutes, I don't think it needs heating...
So I did it, then I saw some water damage (white things) on the back side of the LCD. There is a small board here too, so I cleaned the white thing off with some alcohol.
Then I put the lcd back and voilá, Its WORKING!!!
The only problem is that I damaged the touch screen glass, so I need to order a new one, but its under 20$ so no problem.
Thank you all for your help, I hope that I finished here
Sent from my SM-N9005 using XDA Free mobile app
Good to know! Thank you for the update
Other solution is remove battery five minute and reconnect battery