How to change resolution and keep capacitive buttons functions

How to change resolution and keep capacitive buttons functions - ZenFone 2 Q&A, Help & Troubleshooting

When changing resolution on my ze551ml, i lost the ability to use the capacitive buttons.
That's probably because the kernel driver uses hardcoded coordinates.
So one could modify the kernel itself and flash, but i've managed to use an userspace solution.
Unfortunately, this requires the use of "bash" and "evtest".
Bash is available to android without efforts, evtest may not, i did not checked.
This is not a problem to me, because i run a full archlinux chroot on my zenfone, but probably my script could be adapted to use android's getevent instead of evtest or could be as inspiration for further developing.
"grep" is used too, it is not strictly necessary, but helps in cpu consumption.
Other cons are:
* To make a long tap, one needs to press and release (on stock, one have just to press for long time) -EDIT- This is solved by the second version of the script, see second post.
* The responsivity of the action is not great, that's due to "input keyevent" android command
* You have to account a little battery consumption; i did my best to make the script light and i think it should be low and depends on how much you touch the screen
* Haptic feedback does not work
Here we go:
Code:
#!/bin/bash
#Command needed to escape chroot (comment if not running in chroot)
unchroot=/root/scripts/unchroot/unchroot.exec.sh
#Touch device
I=/dev/input/event1
#Original vertical resolution
Ymin=1920
#New size
SIZE=720x1280
#New dpi
DPI=320
#Buttons coordinates, min, max
BACK_0=150
BACK_1=250
HOME_0=500
HOME_1=600
RECENT_0=827
RECENT_1=927
#Long presso duration (1000000=1second)
LONG_PRESS_TIME=1000000
#Do not configure further
LC_ALL=C
#Function to exit cleanly
exit_function() {
echo "Quitting..."
killall evtest
$unchroot "wm size reset"
$unchroot "wm density reset"
sleep 1
$unchroot "wm density reset"
sleep 5
kill `pidof org.pocketworkstation.pckeyboard`
exit 0
}
#Restore resolution on exit
trap exit_function SIGINT SIGTERM
#Set resolution and dpi
$unchroot "wm size $SIZE"
$unchroot "wm density $DPI"
sleep 1
#Set it again to correct some glitches
$unchroot "wm density $DPI"
sleep 2
#Hacker's keyboard does not like that...
kill `pidof org.pocketworkstation.pckeyboard`
#Hacky: kill leftover evtest processes
killall evtest
#Be nice...
renice -n 19 $$
#Start main "sniffing" cycle:
evtest $I | grep 'BTN_TOUCH' -B10 --line-buffered | \
while read line; do
case $line in
*'(BTN_TOUCH), value 1'*) #Tap Down
#Store the full evtest line, it will be used later to check press time
down_line=$line
;;
*'(BTN_TOUCH), value 0'*) #Tap Up
Y=${Line_Y##* }
#Check that Y is on the Navigation bar
if [[ $Y -ge $Ymin ]] ; then
#Extract TAP UP time
split=(${line//,/ })
time_up=${split[2]}
time_up=${time_up//./}
#Extract TAP DOWN time
split=(${down_line//,/ })
time_down=${split[2]}
time_down=${time_down//./}
diff=$(($time_up-$time_down))
#Set --longpress parameter?
if [ "$diff" -ge "$LONG_PRESS_TIME" ] ; then
LP='--longpress'
#echo "long press"
else
LP=''
#echo "short press"
fi
#Check what key we pressed and emit keyevent
X=${Line_X##* }
if [ "$X" -ge $BACK_0 -a "$X" -le $BACK_1 ]; then
#echo BACK
$unchroot "input keyevent $LP KEYCODE_BACK"
elif [ "$X" -ge $HOME_0 -a "$X" -le $HOME_1 ]; then
$unchroot "input keyevent $LP KEYCODE_HOME"
#echo HOME
elif [ "$X" -ge $RECENT_0 -a "$X" -le $RECENT_1 ]; then
$unchroot "input keyevent $LP KEYCODE_APP_SWITCH"
#echo RECENT
fi
fi
;;
*'ABS_MT_POSITION_X'*) #X coordinate
#Store X position line, will extract coordinate later
Line_X=$line
;;
*'ABS_MT_POSITION_Y'*) #Y coordinate
#Store Y position line, will extract coordinate later
Line_Y=$line
;;
esac
done
if you need the unchroot command, let me know.

Made another version of the script.
This one solves the problem of the long press tap (you can keep the finger pushed and it will understand "long press" action).
Be aware that it is less tested and more error prone.
Also, it uses shared memory; if you run it under android and not chroot, please replace /dev/shm with another existing temporary directory you have write access to of your choice.
Code:
#!/bin/bash
#Command needed to escape chroot (comment if not running in chroot)
unchroot=/root/scripts/unchroot/unchroot.exec.sh
#Touch device
I=/dev/input/event1
#Original vertical resolution
Ymin=1920
#New size
SIZE=720x1280
#SIZE=540x960
#New dpi
DPI=320
#DPI=240
#Buttons coordinates, min, max
BACK_0=150
BACK_1=250
HOME_0=500
HOME_1=600
RECENT_0=827
RECENT_1=927
#Long presso duration (seconds)
LONG_PRESS_TIME=1.00
#Do not configure below this line----------------------------------------------
#May be needed since we use floats
LC_ALL=C
#Function to exit cleanly
exit_function() {
echo "Quitting..."
killall evtest
kill $back_pid
rm /dev/shm/wait_tap_up &
$unchroot "wm size reset"
$unchroot "wm density reset"
sleep 1
$unchroot "wm density reset"
sleep 5
kill `pidof org.pocketworkstation.pckeyboard`
exit 0
}
#Restore resolution and clean on exit
trap exit_function SIGINT SIGTERM EXIT
#Set resolution and dpi
$unchroot "wm size $SIZE"
$unchroot "wm density $DPI"
sleep 1
#Set it again to correct some glitches
$unchroot "wm density $DPI"
sleep 2
#Hacker's keyboard does not like resolution changes...
kill `pidof org.pocketworkstation.pckeyboard`
#Hacky: kill leftover evtest processes
killall evtest
check_long_press() {
Y=${Line_Y##* } #get last field (space delimited string) (Y coordinate)
#Check that Y is on the Navigation bar
if [[ $Y -ge $Ymin ]] ; then
#Short or long press?
#read with timeout from /dev/shm/wait_tap_up fifo
read -t $LONG_PRESS_TIME some_var <> /dev/shm/wait_tap_up
RETVAL=$?
#echo "TAP UP DETECTED"
if (( "$RETVAL" > 0 )); then
LP='--longpress'
echo "long press, removing and recreating stale fifo"
rm /dev/shm/wait_tap_up
mkfifo /dev/shm/wait_tap_up
else
LP=''
echo "short press"
fi
#Check what key we pressed and emit keyevent
X=${Line_X##* } #get last field (space delimited string) (X coordinate)
if [ "$X" -ge $BACK_0 -a "$X" -le $BACK_1 ]; then
#echo BACK
$unchroot "input keyevent $LP KEYCODE_BACK"
elif [ "$X" -ge $HOME_0 -a "$X" -le $HOME_1 ]; then
$unchroot "input keyevent $LP KEYCODE_HOME"
#echo HOME
elif [ "$X" -ge $RECENT_0 -a "$X" -le $RECENT_1 ]; then
$unchroot "input keyevent $LP KEYCODE_APP_SWITCH"
#echo RECENT
fi
fi
#tap_up feeded this function through named pipes
#Set our pid to an unexistant value (0) so that
#tap_up will not try to feed me, since i'm no more.
back_pid=0
return
}
#Make a fifo, needed to pass/raise the tap_down event to the background function
rm /dev/shm/wait_tap_up ; mkfifo /dev/shm/wait_tap_up
#Be nice now...
renice -n 19 $$
#Start main "sniffing" cycle:
evtest $I | grep 'BTN_TOUCH' -B10 --line-buffered | \
while read line; do
case $line in
*'ABS_MT_POSITION_X'*) #X coordinate
#Store X position line, will extract coordinate later
Line_X=$line
;;
*'ABS_MT_POSITION_Y'*) #Y coordinate
#Store Y position line, will extract coordinate later
Line_Y=$line
;;
*'(BTN_TOUCH), value 1'*) #Tap Down
#Store the full evtest line, it will be used later to check press time
down_line=$line
check_long_press &
back_pid=$!
;;
*'(BTN_TOUCH), value 0'*) #Tap Up
#feed check_long_press() with tap_up data, but only if it is running.
if [ -e /proc/$back_pid ] ; then
echo something > /dev/shm/wait_tap_up
fi
;;
esac
done

Related

Init' special ? [ A script resource ]

Added a big list of disable/enable android.permissions
Cleaned up Op.
Made information more concise and easier on the eyes.
read_ahead_kb:
Code:
#
for i in /sys/devices/virtual/bdi/*/read_ahead_kb
do
echo "(AnyMultipleOf 128)" > $i
done
inode_readahead_blks
Code:
#
for i in /sys/fs/ext4/*/inode_*
do
echo "VAR" > $i
done
You won't find more simple scripting SETTING=VALUE...
Code:
write='busybox sysctl -w /sys/devices/system/cpu'
i=$write/cpufreq/conservative
j=$write/cpu0/cpufreq
$j/scaling_governor=conservative
$j/scaling_max_freq=1200000
$jscaling_min_freq=25000
$i/sampling_rate=25000
$i/up_threshold=40
$i/down_threshold=50
$i/freq_step=5
$i/sampling_down_factor=2
|
Code:
\( An Ondemand example \)
write='busybox sysctl -w /sys/devices/cpu'
i=$write/cpufreq/ondemand
j=$write/cpu0/cpufreq
$j/scaling_governor=ondemand
$j/scaling_min_freq=25000
$j/scaling_max_freq=1400000
$i/sampling_rate=50000
$i/up_threshold=65
$i/powersave_bias=10
$i/sampling_down_factor=3
$i/down_differential=30
$i/freq_step=65
|
Code:
\( Pegasus example \)
write='busybox sysctl -w /sys/devices/system/cpu'
i=$write/cpufreq/pegasusq
j=$write/cpu0/cpufreq
$j/scaling_governor=pegasusq
$j/scaling_min_freq=25000
$j/scaling_max_freq=1400000
$i/pegasusq/up_threshold=80
$i/pegasusq/up_threshold_at_min_freq=65
$i/pegasusq/sampling_down_factor=5
$i/pegasusq/down_differential=5
$i/pegasusq/freq_step=60
$i/freq_for_responsiveness=500000
$i/pegasusq/cpu_up_rate=10
$i/pegasusq/cpu_down_rate=20
$i/pegasusq/hotplug_freq_1_1=500000
$i/pegasusq/hotplug_freq_2_0=200000
$i/pegasusq/hotplug_rq_1_1=300
$i/pegasusq/hotplug_rq_2_0=350
$i/pegasusq/ignore_nice_load=0
$i/pegasusq/io_is_busy=1
$i/pegasusq/max_cpu_lock=0
$i/pegasusq/hotplug_lock=0
|
|
simple shell for speed and memory management
Code:
\( You can virtually write any setting \)\
ext4=`busybox sysctl -w /sys/fs/ext4/mmcblk0`
lmk=`busybox sysctl -w /sys/module/lowmemorykiller/parameters`
$ext4\p10/inode_readahead_blks=128
$ext4\p9/inode_readahead_blks=128
$ext4\p7/inode_readahead_blks=256
$ext4\p12/inode_readahead_blks=64
$ext4\p10/inode_goal=16
$ext4\p9/inode_goal=16
$ext4\p7/inode_goal=16
$ext4\p12/inode_goal=16
busybox sysctl -w /proc/1/oom_adj=-17
$lmk/adj=0,2,-4,8,12,15
$lmk/minfree=1024,3072,5120,12288,17408,24566
Screen state script that turns on and off both cpus

For now, this Post will be home to I/O tweaks
Queue settings unknown to most that
Code:
for i in /sys/block/*/*/force*
do
echo "0" > $i
echo 0 > /sys/block/mmcblk0/mmcblk0p1/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p10/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p11/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p12/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p2/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p3/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p4/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p5/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p6/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p7/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p8/ro
echo 0 > /sys/block/mmcblk0/mmcblk0p9/ro
Now you`re ready to adjust stuff...
Code:
for i in /sys/devices/virtual/block/*/queue
do
echo "sio" > $i/scheduler
echo "4096" > $i/minimum_io_size
echo "1" > $i/add_random
echo "4096" > $i/discard_granularity
echo "1" > /discard_zeroes_data
echo "1" > $i/discard_max_bytes
echo "1024" > $i/optimal_io_size
done
|or
for i in /sys/devices/virtual/block/*/queue
do
echo "deadline" > $i/scheduler
echo "2048" > $i/minimum_io_size
echo "1" > $i/add_random
echo "0" > $i/discard_max_bytes
echo "0" > $i/discard_granularity
echo "1" > /discard_zeroes_data
echo "128" > $i/optimal_io_size
done
I have so many variations and these ftmp dont have parameters so Ill let you get creative on those.

Sys Call
Valid keys for /etc/sysctl.conf
I meant for this list to be the OP.. but alas.. i was 11000 or so character to heavy.. lol
A gift ( not all sysctl calls are adjustable and this list is raw. there will be one or two no goes ..)
( wow, I hadn't realized there was near 800 settings in here.... )
ICS SYSCALL MASTER KEY
Alright, I know that most of you will already know how to use a sysctl.conf, but there are probably a couple
things that you didn't know about sysctl, so I may as well start with the obvious...
Code:
\\the following is the easiest way to use sysctl.conf, it is ideally done at init but is equally as easy to use from termemu\\
#/system/bin/sh \\ for init.d \\
sysctl -p \\ from terminal emulator you would have first signed it as usr \\
Now for one you may not now
I'm sure you've seen it used on each command.. (something like 'busybox sysctl -e -w vm.ridin_dirty=example)
*note in sysctl, -(e) is to skip displaying key (e)rrors and keep reading; -n is umber errors i believe; -w is (w)rite; the -p above is (p)rint sysclt.conf
Code:
\\ this is a nice little trick, there are over around 30 kb of keys,,what to do?? \\
su \\ or #/system/bin/sh if in a script \\
sysctl -p /etc/where/ever/your/2nd/sysctl/is
sysctl -p /or/your/5th
sysctl -p $0 <\\ or call your working script itself.\\>
<\\next is the command to create master list from your own device\\>
[B]sysctl -A > /data/log/MasterSysctl.txt[/B]
<\\and this next one,,, well this next is just priceless.. how's this for difficult syntax\\>
sysctl -w /proc/1/oom_adj=-17 <\\yes,, I mean..it...\\>
sysctl -w /sys/devices/virtual/block/loop1/queue/scheduler=easiest_way_to_apply_any_setting_you_arent_sure_of
Some working examples coming soon.

CpuFreq slash Governor settings
Similar but more refined and for a PEGASUS SETUP
Customize it all...
This is an advanced example made simple.. This one will set (between 6) governor and its settings, max and min freq, readahead kb in all of BDI, and inode readahead blks in each mmcblk.
And its 2.2* kb. And you only need to edit the subs if you wamt...
{no mem management or screenstate, but I just had a 4.5 hour screen on cycle at 1.4 max and scoring 4600+ on quadrants...}
Code:
#!/system/bin/sh
chmod 0644 /sys/block/*/queue/*
mount -o remount,rw / /
mount -o remount.rw /system /system
governor=pegasusq
max_freq=1400000
min_freq=50000
inode_readahead=128
read_ahead_kb=3840
cpu=/sys/devices/system/cpu/cpu0/cpufreq
echo "$min_freq" > $cpu/scaling_min_freq
echo "$max_freq" > $cpu/scaling_max_freq
for i in /sys/block/*/*/force_ro
do
echo "0" > $i
done
for i in /sys/class/bdi/*/read*
do
echo "$read_ahead_kb" > $i
done
for i in /sys/fs/ext4/*/inode_*
do
echo "$inode_readahead" > $i
done
for i in $cpu/scaling_governor
do
echo "$governor" > $i
done
for i in /sys/devices/system/cpu/cpufreq
do
active=`cat $cpu/scaling_governor`
Begin_ondemand
echo "40000" > $i/ondemand/sampling_rate
echo "70" > $i/ondemand/up_threshold
echo "15" > $i/ondemand/powersave_bias
echo "70" > $i/ondemand/freq_step
echo "3" > $i/ondemand/sampling_down_factor
Begin_smartassv2
echo "800000" > $i/smartass/awake_ideal_freq
echo "200000" > $i/smartass/sleep_ideal_freq
echo "800000" > $i/smartass/sleep_wakeup_freq
echo "75" > $i/smartass/max_cpu_load
echo "45" > $i/smartass/min_cpu_load
echo "0" > $i/smartass/ramp_up_step
echo "0" > $i/smartass/ramp_down_step
echo "24000" > $i/smartass/up_rate_us
echo "99000" > $i/smartass/down_rate_us
Begin_interactive
echo "80" > $i/interactive/go_hispeed_load
echo "40000" > $i/interactive/min_sample_time
echo "20000" > $i/interactive/timer_rate
#Begin_pegasusq
echo "80" > $i/pegasusq/up_threshold
echo "65" > $i/pegasusq/up_threshold_at_min_freq
echo "5" > $i/pegasusq/sampling_down_factor
echo "5" > $i/pegasusq/down_differential
echo "60" > $i/pegasusq/freq_step
echo "400000" > $i/freq_for_responsiveness
echo "10" > $i/pegasusq/cpu_up_rate
echo "20" > $i/pegasusq/cpu_down_rate
echo "400000" > $i/pegasusq/hotplug_freq_1_1
echo "300000" > $i/pegasusq/hotplug_freq_2_0
echo "300" > $i/pegasusq/hotplug_rq_1_1
echo "350" > $i/pegasusq/hotplug_rq_2_0
echo "0" > $i/pegasusq/ignore_nice_load
echo "1" > $i/pegasusq/io_is_busy
echo "0" > $i/pegasusq/max_cpu_lock
echo "0" > $i/pegasusq/hotplug_lock
#Begin_lulzactive
echo "60" > $i/lulzactive/inc_cpu_load
echo "4" > $i/lulzactive/pump_up_step
echo "1" > $i/lulzactive/pump_down_step
echo "10000" > $i/lulzactive/up_sample_time
echo "70000" > $i/lulzactive/down_sample_time
echo "5" > $i/lulzactive/screen_off_min_step
#Begin_conservative
echo "55" > $i/conservative/up_threshold
echo "25000" > $i/conservative/sampling_rate
echo "3" > $i/conservative/sampling_down_factor
echo "40" > $i/conservative/down_threshold
echo "5" > $i/conservative/freq_step
done
exit 0

Odex all data apps
http://forum.xda-developers.com/showthread.php?p=32305612
Here's a link to a post with a Flashable busybox (with extra-goodies)

PhAkEer said:
a place where one can come to copy/plaste sections
Click to expand...
Click to collapse
I know how to copy, but what is this plaste you speak of?
anyways, this looks promising for adding some more scripts in one spot for all.
Sent from my SPH-D710 using Tapatalk
Click here for custom mods for your E4GT

Prove it

PhAkEer said:
Prove it
Click to expand...
Click to collapse
Edited in a quote before you edited :screwy: haha
Sent from my SPH-D710 using Tapatalk
Click here for custom mods for your E4GT

What is a script? And what do all those fancy thingy things you posted do? Oh, and I spilled grape juice all over my phone. Its still dripping out of it. Why do you think it won't turn on? Also, can you come help me pick my nose?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

How did this thread sneak in on me bro? A little sly-of-hand action there huh.... hook 'em in placebo and create another thread... then mention nonchalantly in placebo thread to check your other thread for the latest.Lol
Looking forward to seeing where this one leads.. nice work man!
Sent from my SPH-D710 using Xparent Blue Tapatalk 2

blackcanopy said:
How did this thread sneak in on me bro? A little sly-of-hand action there huh.... hook 'em in placebo and create another thread... then mention nonchalantly in placebo thread to check your other thread for the latest.Lol
Looking forward to seeing where this one leads.. nice work man!
Sent from my SPH-D710 using Xparent Blue Tapatalk 2
Click to expand...
Click to collapse
Come one now, brah. You know exactly where this goes....
(this leads to me being in your backpack after a while.. and...
to my ultimate goal.... I sleep.. for at least 6 hours at once...)

Anybody want a script to odex data/apps??
Wrote it this morning.
Just need dexopt-wrapper and then execute this.. no reboot, apps keep their classes.dex for the future as well...
Code:
#!/system/bin/sh
J=/system/framework
A=/data/app
W=/system/xbin/dexopt-wrapper
mount -o remount,rw /system /system
mount -o remount,rw /data /data
rm -f $A/*.odex
for i in $A/*
do
name=`basename $i .apk`
$W $A/$name.apk $A/$name.odex $J/core.jar:$J/core-junit.jar:$J/bouncycastle.jar:$J/ext.jar:$J/framework.jar:$J/framework2.jar:$J/android.policy.jar:$J/services.jar:$J/apache-xml.jar
chmod 0644 $A/$name.odex
done
echo $i
sleep 2
exit 0
( and telling me if this stuff does or does not work is NOT off topic ftr )

Haven't even had time to look at this to see what it does...
Found it in an unnamed folder in a backup..
If anybodies knows who's work this is please say so..
I'm only posting it to get it off of my work pc.. I'll look into it later.
Code:
#!/system/bin/sh
#
#
readdebug() {
DUAL_CORE_DEBUG=`cat /system/etc/dual_core/debug`
DUAL_CORE_DEBUG=${DUAL_CORE_DEBUG:=0}
}
log() {
if [ "$DUAL_CORE_DEBUG" = "1" ] ; then
echo "$(date): [email protected]" >> /devlog/dual_core
fi
}
logcpu() {
if [ "$DUAL_CORE_DEBUG" = "1" ] ; then
local NOW_FREQ=`cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq`
local NOW=`cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq`
log "CPU[0]: scaling_max_freq=$NOW"
local NOW_ONLINE=`cat /sys/devices/system/cpu/cpu1/online`
log "CPU[1]: online=$NOW_ONLINE"
if [ -f /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq ] ; then
local NOW=`cat /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq`
log "CPU[1]: scaling_max_freq=$NOW"
fi
fi
}
init_dc_fs() {
sysrw
touch /devlog/dual_core ; chmod 777 /devlog/dual_core
touch /system/etc/dual_core/debug ; chmod 777 /system/etc/dual_core/debug
touch /system/etc/dual_core/sleep_frequency ; chmod 777 /system/etc/dual_core/sleep_frequency
touch /system/etc/dual_core/disable_sleep_freq ; chmod 777 /system/etc/dual_core/disable_sleep_freq
sysro
}
waitforwakeup() {
log "waitforwakeup{" ; logcpu
AWAKE=`cat /sys/power/wait_for_fb_wake`
if [ "$AWAKE" = "awake" ] ; then
CPU0_FREQ_AWAKE=${CPU0_FREQ_AWAKE:="$CPU0_FREQ_BOOT"}
log "Awake triggered... old awake is: $CPU0_FREQ_AWAKE"
log "CPU[1] try set online"
chmod 644 /sys/devices/system/cpu/cpu1/online
echo "1" > /sys/devices/system/cpu/cpu1/online
chmod 444 /sys/devices/system/cpu/cpu1/online
log "CPU[1] online"
if [ "$DISABLE_SLEEP" = "1" ] || [ "$OC_DAEMON" = "1" ] ; then
log "sleep cpu0 frequency mod disabled"
else
log "waking up from earlier sleep.. set to old awake frequency = $CPU0_FREQ_AWAKE"
echo "$CPU0_FREQ_AWAKE" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
fi
sleep 1
echo "$CPU0_FREQ_AWAKE" > /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
echo "ondemand" > /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
chmod 444 /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
log "}wakeup" ; logcpu
fi
}
waitforsleep() {
log "waitforsleep{" ; logcpu
SLEEPING=`cat /sys/power/wait_for_fb_sleep`
if [ "$SLEEPING" = "sleeping" ] ; then
log "Sleep triggered..."
sleep_cpu0
log "CPU[1]: try set offline"
chmod 644 /sys/devices/system/cpu/cpu1/online
echo "0" > /sys/devices/system/cpu/cpu1/online
chmod 444 /sys/devices/system/cpu/cpu1/online
log "CPU[1]: offline"
fi
log "}waitforsleep" ; logcpu
}
sleep_cpu0() {
CPU0_FREQ_AWAKE=`cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq`
log "Sleeping, remember awake frequency: $CPU0_FREQ_AWAKE"
DISABLE_SLEEP=`cat /system/etc/dual_core/disable_sleep_freq`
if [ "$DISABLE_SLEEP" = "1" ] || [ "$OC_DAEMON" = "1" ] ; then
log "DISABLE_SLEEP=1 or OCD detected"
else
if [ -e /system/etc/dual_core/sleep_frequency ] ; then
SLEEP_FREQUENCY=`cat /system/etc/dual_core/sleep_frequency`
log "sleep_frequency setting found, using $SLEEP_FREQUENCY instead of $CPU0_FREQ_AWAKE"
fi
SLEEP_FREQUENCY=${SLEEP_FREQUENCY:=DEFAULT_SLEEP_FREQUENCY}
echo "$SLEEP_FREQUENCY" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
log "Set cpu0 frequency to $SLEEP_FREQUENCY"
fi
}
DEFAULT_SLEEP_FREQUENCY=192000
init_dc_fs
DUAL_CORE_DEBUG="1"
log "Starting..."; logcpu
if [ -f /system/etc/virtuous_oc/wake_max_freq ] ; then
OC_DAEMON=1
log "OC Daemon found."
fi
DISABLE_SLEEP=`cat /system/etc/dual_core/disable_sleep_freq`
CPU0_FREQ_BOOT=`cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq`
STATE=`cat /sys/power/state_onchg`
if [ "$STATE" = "chgoff" ] ; then
log "device is asleep, scaling down"
sleep_cpu0
fi
DUAL_CORE_DEBUG="0"
(while : ; do
waitforwakeup
readdebug
waitforsleep
readdebug
done &)
at a glance it looks like an extremely over complicated screenstate script....

PhAkEer said:
Haven't even had time to look at this to see what it does...
Found it in an unnamed folder in a backup..
If anybodies knows who's work this is please say so..
I'm only posting it to get it off of my work pc.. I'll look into it later.
Code:
#!/system/bin/sh
#
#
readdebug() {
DUAL_CORE_DEBUG=`cat /system/etc/dual_core/debug`
DUAL_CORE_DEBUG=${DUAL_CORE_DEBUG:=0}
}
log() {
if [ "$DUAL_CORE_DEBUG" = "1" ] ; then
echo "$(date): [email protected]" >> /devlog/dual_core
fi
}
logcpu() {
if [ "$DUAL_CORE_DEBUG" = "1" ] ; then
local NOW_FREQ=`cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq`
local NOW=`cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq`
log "CPU[0]: scaling_max_freq=$NOW"
local NOW_ONLINE=`cat /sys/devices/system/cpu/cpu1/online`
log "CPU[1]: online=$NOW_ONLINE"
if [ -f /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq ] ; then
local NOW=`cat /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq`
log "CPU[1]: scaling_max_freq=$NOW"
fi
fi
}
init_dc_fs() {
sysrw
touch /devlog/dual_core ; chmod 777 /devlog/dual_core
touch /system/etc/dual_core/debug ; chmod 777 /system/etc/dual_core/debug
touch /system/etc/dual_core/sleep_frequency ; chmod 777 /system/etc/dual_core/sleep_frequency
touch /system/etc/dual_core/disable_sleep_freq ; chmod 777 /system/etc/dual_core/disable_sleep_freq
sysro
}
waitforwakeup() {
log "waitforwakeup{" ; logcpu
AWAKE=`cat /sys/power/wait_for_fb_wake`
if [ "$AWAKE" = "awake" ] ; then
CPU0_FREQ_AWAKE=${CPU0_FREQ_AWAKE:="$CPU0_FREQ_BOOT"}
log "Awake triggered... old awake is: $CPU0_FREQ_AWAKE"
log "CPU[1] try set online"
chmod 644 /sys/devices/system/cpu/cpu1/online
echo "1" > /sys/devices/system/cpu/cpu1/online
chmod 444 /sys/devices/system/cpu/cpu1/online
log "CPU[1] online"
if [ "$DISABLE_SLEEP" = "1" ] || [ "$OC_DAEMON" = "1" ] ; then
log "sleep cpu0 frequency mod disabled"
else
log "waking up from earlier sleep.. set to old awake frequency = $CPU0_FREQ_AWAKE"
echo "$CPU0_FREQ_AWAKE" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
fi
sleep 1
echo "$CPU0_FREQ_AWAKE" > /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
echo "ondemand" > /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
chmod 444 /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor
log "}wakeup" ; logcpu
fi
}
waitforsleep() {
log "waitforsleep{" ; logcpu
SLEEPING=`cat /sys/power/wait_for_fb_sleep`
if [ "$SLEEPING" = "sleeping" ] ; then
log "Sleep triggered..."
sleep_cpu0
log "CPU[1]: try set offline"
chmod 644 /sys/devices/system/cpu/cpu1/online
echo "0" > /sys/devices/system/cpu/cpu1/online
chmod 444 /sys/devices/system/cpu/cpu1/online
log "CPU[1]: offline"
fi
log "}waitforsleep" ; logcpu
}
sleep_cpu0() {
CPU0_FREQ_AWAKE=`cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq`
log "Sleeping, remember awake frequency: $CPU0_FREQ_AWAKE"
DISABLE_SLEEP=`cat /system/etc/dual_core/disable_sleep_freq`
if [ "$DISABLE_SLEEP" = "1" ] || [ "$OC_DAEMON" = "1" ] ; then
log "DISABLE_SLEEP=1 or OCD detected"
else
if [ -e /system/etc/dual_core/sleep_frequency ] ; then
SLEEP_FREQUENCY=`cat /system/etc/dual_core/sleep_frequency`
log "sleep_frequency setting found, using $SLEEP_FREQUENCY instead of $CPU0_FREQ_AWAKE"
fi
SLEEP_FREQUENCY=${SLEEP_FREQUENCY:=DEFAULT_SLEEP_FREQUENCY}
echo "$SLEEP_FREQUENCY" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
log "Set cpu0 frequency to $SLEEP_FREQUENCY"
fi
}
DEFAULT_SLEEP_FREQUENCY=192000
init_dc_fs
DUAL_CORE_DEBUG="1"
log "Starting..."; logcpu
if [ -f /system/etc/virtuous_oc/wake_max_freq ] ; then
OC_DAEMON=1
log "OC Daemon found."
fi
DISABLE_SLEEP=`cat /system/etc/dual_core/disable_sleep_freq`
CPU0_FREQ_BOOT=`cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq`
STATE=`cat /sys/power/state_onchg`
if [ "$STATE" = "chgoff" ] ; then
log "device is asleep, scaling down"
sleep_cpu0
fi
DUAL_CORE_DEBUG="0"
(while : ; do
waitforwakeup
readdebug
waitforsleep
readdebug
done &)
at a glance it looks like an extremely over complicated screenstate script....
Click to expand...
Click to collapse
You might be right! It kinda looks like the script from the CPU sleep thread from here http://forum.xda-developers.com/showthread.php?t=1739457
Sent from my SPH-D710 using Tapatalk 2

Customizable Pegasus.
As is I'm getting something I'd recognize as a score in quad on jb... I thought the day would never come....
Code:
#!/system/bin/sh
# SETUP FOR PEGASUS
# I/O Settings
scheduler=deadline
read_ahead=3072
inode_blks=64
inode_goal=8
# CPU Freq Settings
min_freq=200
max_freq=1200
up_thresh=80
sampling=40000
sampling_factor=3
down_diff=5
freq_step=60
response_freq=500000
up_rate=20
down_rate=30
freq_1_1=400000
freq_2_0=300000
rq_1_1=400
rq_2_0=350
ignore_nice=0
io_is_busy=0
cpu_lock=0
lockR=0
# Stream settings
max_mb_scan=0
min_mb_scan=0
mb_stream_req=0
max_writeback_bump=32
req_order2=0
prealloc_mb=768
# Here we go again...lol
set -x
exec > /data/log/Pegasus.log 2>&1
/system/bin/sh
for j in $(/system/xbin/busybox mount | /system/xbin/busybox grep ext4 | /system/xbin/busybox cut -d " " -f3)
do
sync
/system/xbin/busybox mount -o remount,noatime,barrier=0,commit=5 $j
done
mount -o remount,noatime,nobh,nodiratime,nodelalloc,noauto_da_alloc,barrier=0 /system /system
mount -o remount,noatime,nobh,nodiratime,nodelalloc,noauto_da_alloc,barrier=0,commit=0 /cache /cache
mount -o remount,noatime,nodiratime,delalloc,noauto_da_alloc,barrier=0,commit=0 /data /data
for i in /sys/fs/ext4/*
do
echo "$max_mb_scan" > $i/mb_max_to_scan
echo "$min_mb_scan" > $i/mb_min_to_scan
echo "$inode_blks" > $i/inode_readahead_blks
echo "$inode_goal" > $i/inode_goal
echo "$mb_stream_req" > $i/mb_stream_req
echo "$max_writeback_bump" > $i/max_writeback_mb_bump
echo "$preaoc_mb" > $i/mb_group_prealloc
echo "$req_order2" > $i/mb_order2_req
done
echo "pegasusq" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
for i in /sys/devices/system/cpu/cpufreq/pegasusq
do
echo "$up_thresh" > $i/up_threshold
echo "$sampling" > $i/sampling_rate
echo "$sampling_factor" > $i/sampling_down_factor
echo "$down_diff" > $i/down_differential
echo "$freq_step" > $i/freq_step
echo "$up_rate" > $i/cpu_up_rate
echo "$down_rate" > $i/cpu_down_rate
echo "$freq_1_1" > $i/hotplug_freq_1_1
echo "$freq_2_0" > $i/hotplug_freq_2_0
echo "$rq_1_1" > $i/hotplug_rq_1_1
echo "$rq_2_0" > $i/hotplug_rq_2_0
echo "$ignore_nice" > $i/ignore_nice_load
echo "$io_is_busy" > $i/io_is_busy
echo "$cpu_lock" > $i/max_cpu_lock
done
for i in /sys/devices/virtual/bdi/*/read_ahead_kb
do
echo "$read_ahead" > $i
done
for i in /sys/class/block/*/queue
do
echo "$scheduler" > $i/scheduler
echo "$read_ahead" > $i/read_ahead_kb
done
case "$min_freq" in
*)
i=/sys/devices/system/cpu/cpu0/cpufreq
;;
25)
echo "25000" > $i/scaling_min_freq
;;
50)
echo "50000" > $i/scaling_min_freq
;;
100)
echo "100000" > $i/scaling_min_freq
;;
200)
echo "200000" > $i/scaling_min_freq
;;
300)
echo "300000" > $i/scaling_min_freq
;;
400)
echo "400000" > $i/scaling_min_freq
;;
500)
echo "500000" > $i/scaling_min_freq
;;
esac;
case "$max_freq" in
800)
echo "800000" > $cpu/scaling_max_freq
;;
900)
echo "900000" > $cpu/scaling_max_freq
;;
1000)
echo "1000000" > $cpu/scaling_max_freq
;;
1100)
echo "1100000" > $cpu/scaling_max_freq
;;
1200)
echo "1200000" > $cpu/scaling_max_freq
;;
1300)
echo "1300000" > $cpu/scaling_max_freq
;;
1400)
echo "1400000" > $cpu/scaling_max_freq
;;
1600)
echo "1600000" > $cpu/scaling_max_freq
;;
esac;

Nice to see this in the development section :thumbup:
-TeaM VeNuM Like A Boss

MiguelHogue said:
Nice to see this in the development section :thumbup:
-TeaM VeNuM Like A Boss
Click to expand...
Click to collapse
It isn't so such much for something to develop, I mainly just wanted the resources available the Tw themers and the like.
The parameters for the section said dev/mod/hack so I'm sure it fits in there somewhere.. I need to start getting some material in here though. . ... watch this...
EEECCCCCCHOOOO
khoeoeoeoe
ohohohohhh
See...

This one is a WIP so pay attention
Dual cpu screenstate script.. simple stuff
the way I have this setup it setup it will call powersave when screen is off. This is only practical if it calls another governor when the screen comes back on, so change it from "sh /data/local/pegasus" to "sh wherever you have a gov script" or to
"echo govofchoice > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor"
Code:
#!/system/bin/sh
#
#
sleep 1m
while [[ "awake" = $AWAKE ]]
do
AWAKE=`cat /sys/power/wait_for_fb_wake`
if [ "awake" = $AWAKE ]
then
echo "1" > /sys/devices/system/cpu/cpu1/online
echo "1" > /sys/devices/system/cpu/cpu0/online
sh /data/local/Pegasus
fi
sleep 2
ASLEEP=`cat /sys/power/wait_for_fb_sleep`
if [ "sleeping" = $ASLEEP ]
then
echo "0" > /sys/devices/system/cpu/cpu1/online
echo "0" > /sys/devices/system/cpu/cpu0/online
echo "powersave" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
fi
sleep 2
done
exit 0

PhAkEer said:
Anybody want a script to odex data/apps??
Wrote it this morning.
Just need dexopt-wrapper and then execute this.. no reboot, apps keep their classes.dex for the future as well...
Code:
#!/system/bin/sh
J=/system/framework
A=/data/app
W=/system/xbin/dexopt-wrapper
mount -o remount,rw /system /system
mount -o remount,rw /data /data
rm -f $A/*.odex
for i in $A/*
do
name=`basename $i .apk`
$W $A/$name.apk $A/$name.odex $J/core.jar:$J/core-junit.jar:$J/bouncycastle.jar:$J/ext.jar:$J/framework.jar:$J/framework2.jar:$J/android.policy.jar:$J/services.jar:$J/apache-xml.jar
chmod 0644 $A/$name.odex
done
echo $i
sleep 2
exit 0
( and telling me if this stuff does or does not work is NOT off topic ftr )
Click to expand...
Click to collapse
Where do we get a copy of dexopt-wrapper? I downloaded the odex station that has it in the zip you had somewhere, but I get status7 error when flashing it.
Sent from my SPH-D710 using Xparent Blue Tapatalk 2

Just extract the wrapper to xbin and youre gtg
Warning: hideous sig acomin..
Need a change of pace?
Odexing Data with a simple script
or
Change your boot splash-screen in two steps

Offset extra power consumption from "overclocking"

Here is something I have used for a long time. On my S3, this text is usually added to my init.qcom.post_boot.sh file found in /etc/ or /system/etc/ (same thing, they are symlinked directories so go whichever route you please)
This particular one is a very simple line of code, but does a fantastic job at keeping the CPU cool, and saving power while its tucked away in my pocket. Performance does not degrade much either. I typically overclock all of my own devices so this is a good offset to that extra power consumption
The code is from my Samsung Note II. However, it will work with the S3. Just remove lines calling out cpu2 and 3.
Values representing speed will need to be modified as well for this device, very simple to do, though, even if you are new.
You can "cat" your /sys/devices/system/cpu/cpu0/scaling_available_frequencies from a programming window/terminal or simply navigate to the directory and read the file.
For those that are "new", the cat command just shoots back information/data found within the file/directory you are calling out. So, doing this is very safe. Give it a shot! Get your hands dirty!
#!/system/bin/sh
(while [ 1 ]; do
SLEEPING=`cat /sys/power/wait_for_fb_sleep`
if [ $SLEEPING = "sleeping" ]; then
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu3/cpufreq/scaling_max_freq
echo 1200000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
echo 1200000 > /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq
echo 1200000 > /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
echo 1200000 > /sys/devices/system/cpu/cpu3/cpufreq/scaling_max_freq
chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
chmod 444 /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq
chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
chmod 444 /sys/devices/system/cpu/cpu3/cpufreq/scaling_max_freq
fi
AWAKE=`cat /sys/power/wait_for_fb_wake`
if [ $AWAKE = "awake" ]; then
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu3/cpufreq/scaling_max_freq
echo 2000000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
echo 2000000 > /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq
echo 2000000 > /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
echo 2000000 > /sys/devices/system/cpu/cpu3/cpufreq/scaling_max_freq
chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
chmod 444 /sys/devices/system/cpu/cpu1/cpufreq/scaling_min_freq
chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
chmod 444 /sys/devices/system/cpu/cpu3/cpufreq/scaling_max_freq
fi

Looks like a pretty easy tweak. :good:

browser is being a little bit funky on me...
proper spacing of the text is important.
(while [ 1 ]; do
SLEEPING=`cat /sys/power/wait_for_fb_sleep` (no spacing for these two lines)
(next line is spaced once)
chmod, and echo lines are all double spaced
Easy to implement, yes, and very effective as I mentioned.

Can you make a flashable zip please
Sent from my SGH-T999 using xda premium

azamataz buckshank said:
browser is being a little bit funky on me...
proper spacing of the text is important.
(while [ 1 ]; do
SLEEPING=`cat /sys/power/wait_for_fb_sleep` (no spacing for these two lines)
(next line is spaced once)
chmod, and echo lines are all double spaced
Easy to implement, yes, and very effective as I mentioned.
Click to expand...
Click to collapse
Code tags?

Easy set Vsel and instant wakeup for CM11(recent nightly built by Quarx) & TWRP 2.8

Easy set Vsel and instant wakeup for CM11(recent nightly built by Quarx) & TWRP 2.8
Hi，all
Recently,I‘ve upgrade defy to CM11 nightly built that Qurax released everyday.And I'm using cm-11-20160628-NIGHTLY-mb52x.zip such a great rom works almost everything and smooth.
MANY THANKS to Quarx!
The rom is using TWRP 2.8.0.0, so I can't find setting CPU Vsel at boot.After some search,it can be done by adding some scripts to /system/etc/init.d/09overclock .(or using AeroControl )
Also,the rom delays to wakeup up to 3 seconds when you click the power button .
And I tried the same CPU governor & I/O schedul that used with 4.1.2 & 4.3.1,and it worked.These two settings built in the rom setting are sometimes failed to work and back to default, so I added them to script too.
Add these scripts to /system/etc/init.d/09overclock ,remember to leave a blank line at the end and set the same right (555) to the file.
Code:
#!/system/bin/sh
#
# Module location
MODULE_DIR="/system/lib/modules"
MODULE="/system/lib/modules/overclock_defy.ko"
SYMSEARCH_MODULE="/system/lib/modules/symsearch.ko"
/system/xbin/insmod $SYMSEARCH_MODULE
/system/xbin/insmod $MODULE_DIR/cpufreq_stats.ko
cpufreq_table=`grep -e omap2_clk_init_cpufreq_table /proc/kallsyms | sed -e "s/\([0-9A-Fa-f]\{8\}\).*/\1/"`
stats_update=`grep -e cpufreq_stats_freq_update /proc/kallsyms | sed -e "s/\([0-9A-Fa-f]\{8\}\).*/\1/"`
/system/xbin/insmod $MODULE omap2_clk_init_cpufreq_table_addr=0x$cpufreq_table
echo 0x$stats_update > /proc/overclock/cpufreq_stats_update_addr
# setVsel at boot,BACKUP your ROM first and use it caution with the stable vsel of your phone!
/system/xbin/busybox echo 55 > /proc/overclock/max_vsel
/system/xbin/busybox echo 1000000 > /proc/overclock/max_rate
/system/xbin/busybox echo 1 300000000 25 > /proc/overclock/mpu_opps
/system/xbin/busybox echo 2 600000000 35 > /proc/overclock/mpu_opps
/system/xbin/busybox echo 3 800000000 45 > /proc/overclock/mpu_opps
/system/xbin/busybox echo 4 1000000000 55 > /proc/overclock/mpu_opps
/system/xbin/busybox echo 0 1000000 > /proc/overclock/freq_table
/system/xbin/busybox echo 1 800000 > /proc/overclock/freq_table
/system/xbin/busybox echo 2 600000 > /proc/overclock/freq_table
/system/xbin/busybox echo 3 300000 > /proc/overclock/freq_table
# avoid wakeup delay when your settings fails sometime in /Settings/Performance/Processor & I/O scheduler.
sleep 60
/system/xbin/busybox echo ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
/system/xbin/busybox echo sio > /sys/block/mmcblk0/queue/scheduler
# Always check /Settings/Performance/Memory management/Allow purging of assets.
# While select ART runtime in Developer options and check Allow purging of assets ,using following minfree to max performance .
# Should put them below sleep 60,use as your choice.
# /system/xbin/busybox echo "0,1,2,4,7,15" > /sys/module/lowmemorykiller/parameters/adj
# /system/xbin/busybox echo "2464,3712,5632,7392,8608,9856" > /sys/module/lowmemorykiller/parameters/minfree
Also,set this to /system/build.prop ,to bring up income call interface much more fast.
ro.telephony.call_ring.delay=0
FYI,
about the last minfree part(other VM sets are ok by default ),I've done some test below.
ALL tested under ART runtime (its bugfree to me and ART is way much better than Dalvik,using Dalvik,browser crashed at 11-12 gifs no matter what ).
1.uncheck Allow purging of assets ,browser crashed loading 7 - 8 gifs picture in the webpage
2.check Allow purging of assets ,browser crashed loading 14 - 15 gifs picture (including the gifs above) in the webpage
3.check Allow purging of assets ,and using the minfree above ,browser crashed up to 24 gifs picture (including the gifs above) in the webpage（browser using nearly 320M ram...）
All behaviors the same delay switching to other apps when browser approaching to crash.
After done above ,there are only left 2 bugs to me
1.the menu & search button remap.(menu button can't be remapped to other function in the launcher ,and search button only works as search )
2.call recording not working (still searching method)

KFinally found the answer to bad battery life on our beloved htc 10's/works with Oreo

Save much reading and go to page 61. Answers to bad battery on the HTC 10 are worked out there. It's simplifies everything. Many posts here are works in progress kind of back and forth.
Guides I used for amplify are at the bottom of page 13.
(Remember to thank me in the op if anything here helped.)
After numerous hours of research and testing . Just wanted to reveal what I found. This is made for the OP-3 which is also a snapdragon 820 chipset device.
Ive been using on my Verizon HTC 10 with zero issues so far/ Lee-droid oreo rom/Elemental X -3.02 kernel. Much copy and pasting going on, just wanted to share my find.I take no credit for any of this : other than being willing to test on my device. After flashing the final version of (AKT.V1.6/FinalZIP )through twrp/ located on next page I ticked for the Op3 OR SNAPDRAGON 820 DEVICE from a terminul emilator, then I choose "Project Zhana battery" . I used rom toolbox pro's terminal emulator. Choose whatever profile you desire but the one I picked works fine/zero lag. Our other options (as of now) are soilwork scripts made for the HTC 10 or the helix engine now that pnpmgr has been disabled.
. First link is a huge thread on profiles from AKT. Go find which ever works best for your situation.
( I'm not telling you to flash anything. I'm showing you possible routes that have been tested by me. If you do not like results simply Ruu back to stock or dirty flash rom being used to get rid of it all.)
I'm about to tell you how to get buttery smooth, lag-free performance with insanely good battery life, using an old school governor featured in practically every kernel... This tweak is applicable to every phone with any ROM or kernel--stock or custom--that provides the Interactive Governor.
Yeah, yeah... everyone promises good battery with great performance, but who actually delivers? Maybe it isn't as smooth as you want, or maybe it requires something your kernel or ROM don't support. Or maybe the battery life promises just aren't what you expected. There's always some awful compromise. Not here!
This isn't a guide to get 36 hour battery life... provided you never use your phone. That's deep sleep optimization, which is lovely and all, but what good is the phone if you can never use it?! And with the new Marshmallow Doze feature, this strategy is becoming a thing of the past. What I'm talking about is 7-14 hour screen on, actual hands-on usage times! Without compromising anything, you can get 7-8 hour screen on usage with regular, no-compromise usage habits: daytime visible screen brightness, both radios on, sync on, network location on, all the regular usage features, the whole kit and kaboodle... all smooth as a baby's butt and snappy as a Slim Jim! (Up to 14+ hours if you can stand minimum brightness and WiFi-only with a custom ROM and other stuff turned off! And this is with stock voltages and full frequency range--you'll likely get even more if you choose to optimize those as well!)
However, it should be noted that this does not apply to gaming, heavy camera use, etc. Anything that is an automatic battery killer in and of itself. There's nothing that can be done about anything that forces the phone to utilize its maximum resources all the time. But you should know that by now. Further, this guide is about optimizing the CPU as much as possible. It does not cover things like eliminating wakelocks so your phone sleeps well, removing unnecessary and battery draining stock apps, keeping your screen brightness down*, and all that stuff that's been covered in other posts ad infinitum. Those optimizations are up to you.
If you really want to know the principles of this tweaks, please go to this thread since there everything is really well explained and I know you guys just want to apply the tweak and forget about everything behind it, so just keep scrolling!
Voltages and Frequencies:
So recently I have been investigating about the Voltages of our device (since that is a really useful information to know) before that we only have the Nominal frequencies (If you don't know what I am talking about go ahead and read @soniCron thread because I won't explain it) we could develop some tweaks with that, but we were pretty much making blind shots, guessing and hoping that all will be right. Well, now that we have all this information we can optimize our tweaks even more so expect new updates and rework for the current tweaks and of course new ones.
What About Touchboost?
Since I've noticed that a lot of people was asking about Touchboost, I decided to add this little explanation from @soniCron
" Touchboost is a nifty feature in a lot of kernels (including stock on Nexus 5X) that jumps up the frequency so that you experience minimal lag. However, with all the above settings, touchboost is usually detrimental to the efficiency of the device!
We generally want to keep the CPU on the lowest possible frequency as much as possible, and touchboost interferes with that. Further, because we've set up the maximal and minimal efficient clock rates, as well as burst processing from the 2nd CPU core, we don't need touchboost!
If your kernel allows you to shut it off, try to do so and see if the responsiveness of your device is acceptable. On the OP3 (and pretty much all the devices), touchboost adds no perceptual performance gain and only hurts efficiency and battery life. If your kernel doesn't allow you to turn off touchboost, try another one.
Your battery life will thank you! "
With all that been said, you shouldn't confuse Touchboost with CPU Boost and more specifically Input boost. Both are used to boost the clock speed of our device whenever we touch the touchscreen, so we don't suffer any lags.
The difference is that Input boost can be configured and Touchboost cannot, making it a really inefficient.
MY DEVICE LAGS!!! WHY?!?!
First of all, it's a "normal" thing, as I have stated before, all these tweaks have been done for fit my usage or certain usage which is most likely not the same as yours. Because this, when the are put on a certain scenario the might stutter or lag just a bit (If you are experimenting huge lags, you have done something wrong)
And yes, this can be fixed. We have a couple of ways of fixing it:
First of all, Check If the tweaks have been applied correctly
Our first one is modifying the Input boost (not touchboost) most of our tweaks have an already established Input boost clock speeds and time, you can incise does too a bit. For example, we have 960(Mhz) for all the CPU at 40ms you could bump it up to ~1036(Mhz) and 42ms, don't modify too much this values since it will potentially increase your battery drain.
Our second tool for fixing lags is min_sample_time , my recommendation is to increase the value by 5000 each time till you no longer suffer any stutter or lag.
Try another tweak, for example;
If you are using Project X.A.N.A Battery, try using Balanced option...
Still having lag?
Get rid of unnecessary (background-)apps
Try a different IO-Scheduler
Try another profile
My phone still uses too much battery
First of all, Check If the tweaks have been applied correctly
Make sure that you have disabled touchboost.
Set brightness to a lower level.
Use a dark / black theme
Don't play games all day
Try other tweak, for example;
If you are using Project Zhana Balanced, try using Battery option...
How to install:
A flashable zip to be flashed via recovery, which installs scripts of the latest iterations of most profiles (some legacy profiles had to be eliminated for more convenience) and a master script that takes control of all the installed scripts and applies your desired profile at will as soon as you recall it via Terminal Emulator app and get guided by the on-screen instructions.
So to wrap it up:
1- Download the latest AKT_Profile_vX.x.zip file
2- Reboot into TWRP recovery and flash the .zip file
3- After you boot up the phone, leave it to settle for a minute
4- Open up your favorite Terminal Emulator app
5- Grant it superuser permissions by typing in "su" without the quotes
6- After superuser permissions are granted, type in "AKT" without the quotes (yes capitalized)
Download link for AKT
https://forum.xda-developers.com/showpost.php?p=70352820&postcount=2146
Xposed with magic information and downloads.
This is where the rubber meets the road. Amplify and greenify for Oreo!!!
https://forum.xda-developers.com/xposed/unofficial-systemless-xposed-t3388268
(Save yourself some time and jump to page 61 Finally found the answers there. Long live the HTC 10. My device is finally a beast.)

Sounds interesting - might give it a try

It's running like a totally different phone. I'm amazed almost 2 hours of screen on time and still at 70% battery. And I'm casting to my living room TV as well. Still zero lag. So phone is running tasks as well. And I'm back and forth on here. Works nicely.

mattie_49 said:
It's running like a totally different phone. I'm amazed almost 2 hours of screen on time and still at 70% battery. And I'm casting to my living room TV as well. Still zero lag. So phone is running tasks as well. And I'm back and forth on here. Works nicely.
Click to expand...
Click to collapse
Are you using stock elemental x settings or other ?

Code:
#!/system/bin/sh
#Author: Asiier
#Settings By: Asiier
#Device: One Plus 3
#Codename: Project Zhana (BT)
#Build Status: Stable
#Version: 4.2
#Last Updated: 22/01/2017
#Notes: Please give credit when using this in your work!
#TWEAKS_BEGIN
echo ""
echo --------------------------------------------------------
echo Applying 'Project Zhana (Battery variant)' v4.3
echo Advanced Kernel Settings
echo --------------------------------------------------------
sleep 0.5
echo Author: Asiier
echo Settings By: Asiier
echo "Device: One Plus 3 & SD820 Devices"
echo Codename: 'Project Zhana (BT)'
echo Build Status: Stable
echo Last Updated: 19/09/2017
echo For more information go to the XDA theard
echo ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sleep 0.3
echo Checking Android version...
if grep -q 'ro.build.version.sdk=25' /system/build.prop; then
echo Android Nougat 7.1.X detected!
sleep 0.3
echo N detected... Applying proper settings
fi
if grep -q 'ro.build.version.sdk=24' /system/build.prop; then
echo Android Nougat 7.0.X detected!
sleep 0.3
echo N detected... Applying proper settings
fi
if grep -q 'ro.build.version.sdk=23' /system/build.prop; then
echo Android Marshmallow 6.0.1 detected!
sleep 0.3
echo MM detected... Applying proper settings
fi
echo ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sleep 0.3
#Apply settings to LITTLE cluster
echo Applying settings to LITTLE Cluster...
sleep 0.5
#Temporarily change permissions to governor files for the LITTLE cluster to enable Interactive governor
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
echo interactive > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
#Grab Maximum Achievable Frequency for the LITTLE Cluster
maxfreq=$(cat "/sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq")
if test "$maxfreq" -eq 1593600; then
#Temporarily change permissions to governor files for the Big cluster to set the maximum frequency to 1593MHz
echo No LITTLE Cluster Overclocking detected.
echo Applying appropriate values.
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
echo 1593600 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq #Core 0 Maximum Frequency = 1593MHz
chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
echo 70 480000:65 556800:75 729600:82 960000:86 1036800:2 1228800:99 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
fi
if test "$maxfreq" -eq 1728000; then
#Temporarily change permissions to governor files for the Little cluster to set the maximum frequency to 1728MHz
echo LITTLE Cluster Overclocking detected.
echo Applying appropriate values.
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
echo 1728000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq #Core 0 Maximum Frequency = 1728MHz
chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
echo 70 480000:65 556800:75 729600:82 960000:86 1036800:2 1228800:99 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
maxfreq=$(cat "/sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq")
fi
if test "$maxfreq" -lt 1593600; then
#Temporarily change permissions to governor files for the Big cluster to set the maximum frequency to 1593MHz
echo LITTLE Cluster Underclocking detected!!
sleep 1
echo We recommend not to UnderClock the CPU as the tweaks already will take care of that If needed
echo The tweaks will continue getting applied but we recommend setting the CPU to Max frequency!
sleep 4
#chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
#echo 1593600 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq #Core 0 Maximum Frequency = 1593MHz
#chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
echo 70 480000:65 556800:75 729600:82 960000:86 1036800:2 1228800:99 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
elif test $maxfreq -gt 1728000; then
#Temporarily change permissions to governor files for the Little cluster to set the maximum frequency to 1728MHz
echo LITTLE Cluster Overclocking detected.
sleep 1
echo This OverClock is higher than normal and only possible on Xceed Kernel
echo The tweak will continue getting applyed
echo " Althought it might no reach the maximum frequency you have setted as it haven't been made to work with frecuencies higher than 1728 Mhz "
#chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
#echo 1728000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq #Core 0 Maximum Frequency = 1728MHz
#chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
echo 70 480000:65 556800:75 729600:82 960000:86 1036800:2 1228800:99 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
chmod 444 /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
fi
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/interactive/*
echo 220000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/timer_slack
echo 307200 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/hispeed_freq
echo 100000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/timer_rate
echo 0 729600:76000 960000:99000 1228800:150000 1478400:170000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/above_hispeed_delay
echo 155 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/go_hispeed_load
echo 22000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/min_sample_time
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/max_freq_hysteresis
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/ignore_hispeed_on_notif
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/boost
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/fast_ramp_down
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/align_windows
echo 1 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/use_migration_notif
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/use_sched_load
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/boostpulse_duration
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/io_is_busy
if [ -e "/sys/devices/system/cpu/cpu0/cpufreq/interactive/enable_prediction" ]; then
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/interactive/enable_prediction
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/enable_prediction
fi
sleep 0.5
#Apply settings to Big cluster
echo Applying settings to BIG Cluster
sleep 0.2
#Temporarily change permissions to governor files for the LITTLE cluster to enable Interactive governor
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/scaling_governor
echo interactive > /sys/devices/system/cpu/cpu2/cpufreq/scaling_governor
chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/scaling_governor
#Grab Maximum Achievable Frequency for the Big Cluster
maxfreq=$(cat "/sys/devices/system/cpu/cpu2/cpufreq/cpuinfo_max_freq")
if test $maxfreq -eq 2150400; then
#Temporarily change permissions to governor files for the Big cluster to set the maximum frequency to 2150MHz
echo No BIG Cluster Overclocking detected.
echo Applying appropriate values.
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
echo 2150400 > /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq #Core 2 Maximum Frequency = 2150MHz
chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
echo 65 940800:80 1036800:2 1401600:95 1824000:98 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
#Set overclock max frequency compatible target_loads
elif test $maxfreq -eq 2265600; then
#Temporarily change permissions to governor files for the Big cluster to set the maximum frequency to 2265MHz
echo BIG Cluster Overclocking detected.
echo Applying appropriate values.
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
echo 2265600 > /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq #Core 2 Maximum Frequency = 2265MHz
chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
echo 65 940800:80 1036800:2 1401600:95 1824000:98 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
fi
if test $maxfreq -lt 2150400; then
#Temporarily change permissions to governor files for the Big cluster to set the maximum frequency to 1593MHz
echo BIG Cluster Underclocking detected!!
sleep 1
echo We recommend not to UnderClock the CPU as the tweaks already will take care of that If needed
echo The tweaks will continue getting applied but we recommend setting the CPU to Max frequency!
sleep 4
#chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
#echo 1593600 > /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq #Core 0 Maximum Frequency = 1593MHz
#chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
echo 65 940800:80 1036800:2 1401600:95 1824000:98 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
elif test $maxfreq -gt 2265600; then
#Temporarily change permissions to governor files for the Little cluster to set the maximum frequency to 1728MHz
echo BIG Cluster Overclocking detected.
sleep 1
echo This OverClock is higher than normal and only possible on Xceed Kernel
echo The tweak will continue getting applyed
echo " Althought it might no reach the maximum frequency you have setted as it haven't been made to work with frecuencies higher than 2265600 Mhz "
sleep 4
#chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
#echo 1728000 > /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq #Core 0 Maximum Frequency = 1728MHz
#chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
echo 65 940800:80 1036800:99 1401600:95 1824000:98 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
chmod 444 /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
fi
sleep 0.5
#Tweak Interactive Governor
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/*
echo 140000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/timer_slack
echo 1401600 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/hispeed_freq
echo 65000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/timer_rate
echo 32000 940800:85000 1248000:96000 1401600:88000 1632000:80000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/above_hispeed_delay
echo 99 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/go_hispeed_load
echo 11000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/min_sample_time
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/max_freq_hysteresis
echo 1 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/ignore_hispeed_on_notif
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/boost
echo 1 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/fast_ramp_down
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/align_windows
echo 1 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/use_migration_notif
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/use_sched_load
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/boostpulse_duration
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/io_is_busy
if [ -e "/sys/devices/system/cpu/cpu2/cpufreq/interactive/enable_prediction" ]; then
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/interactive/enable_prediction
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/enable_prediction
fi
echo "=========================================="
echo Checking whether you are using a Sultanxda based ROM or not
echo "=========================================="
#Checking whether you are using a Sultanxda based ROM or not
echo Checking ROM...
sleep 0.2
echo Applying appropriate values.
if [ -e "/sys/kernel/cpu_input_boost/enabled" ]; then
echo Enabling Input Boost for the LITTLE cluster @556 MHz and for the BIG Cluster @0Mhz and Custom thermal driver of Sultanxda
chmod 644 /sys/kernel/cpu_input_boost/*
echo 1 > /sys/kernel/cpu_input_boost/enabled
echo 66 > /sys/kernel/cpu_input_boost/ib_duration_ms
echo 556800 0 > /sys/kernel/cpu_input_boost/ib_freqs
chmod 444 /sys/kernel/cpu_input_boost/*
chmod 644 /sys/kernel/msm_thermal/enabled
echo 0 > /sys/kernel/msm_thermal/enabled
chmod 444 /sys/kernel/msm_thermal/enabled
else
#Checking whether you are using a Lineage based ROM or not
echo Checking ROM...
sleep 0.2
if grep -q 'ro.build.flavor=lineage_oneplus3-userdebug' /system/build.prop; then
#Enable Input Boost for LITTLE cluster @556MHz and for BIG cluster @729MHz for 66ms
echo Lineage Based ROM detected
echo Applying appropriate values.
echo Enabling Input Boost at 556 MHz for the LITTLE cluster and at 0 MHz for the BIG Cluster
if [ -e "/sys/module/cpu_boost/parameters/input_boost_freq" ]; then
chmod 644 /sys/module/cpu_boost/parameters/input_boost_freq
echo 0:556800 1:0 2:0 3:0 > /sys/module/cpu_boost/parameters/input_boost_freq
chmod 644 /sys/module/cpu_boost/parameters/input_boost_ms
echo 55 > /sys/module/cpu_boost/parameters/input_boost_ms
else
echo "*Input Boost is not avalible for your Kernel*"
fi
if [ -e "/sys/module/cpu_boost/parameters/boost_ms" ]; then
chmod 644 /sys/module/cpu_boost/parameters/boost_ms
echo 0 > /sys/module/cpu_boost/parameters/boost_ms
else
echo "*Cpu_Boost is not avalible for your Kernel*"
fi
else
#Enable Input Boost for LITTLE cluster @729MHz and for BIG cluster @729Hz for 100ms
echo Non-Lineage ROM detected
echo Applying appropriate values.
echo Enabling Input Boost at 729 MHz for the LITTLE cluster and at 0 MHz for the BIG Cluster
if [ -e "/sys/module/cpu_boost/parameters/input_boost_freq" ]; then
chmod 644 /sys/module/cpu_boost/parameters/input_boost_freq
echo 0:729600 1:0 2:0 3:0 > /sys/module/cpu_boost/parameters/input_boost_freq
chmod 644 /sys/module/cpu_boost/parameters/input_boost_ms
echo 77 > /sys/module/cpu_boost/parameters/input_boost_ms
else
echo "*Input Boost is not avalible for your Kernel*"
fi
if [ -e "/sys/module/cpu_boost/parameters/boost_ms" ]; then
chmod 644 /sys/module/cpu_boost/parameters/boost_ms
echo 0 > /sys/module/cpu_boost/parameters/boost_ms
else
echo "*Cpu_Boost is not avalible for your Kernel*"
fi
fi
fi
sleep 0.3
echo "=========================================="
#Disable TouchBoost
echo Disabling TouchBoost
if [ -e "/sys/module/msm_performance/parameters/touchboost" ]; then
chmod 644 /sys/module/msm_performance/parameters/touchboost
echo 0 > /sys/module/msm_performance/parameters/touchboost
else
echo "*Not supported for your current Kernel*"
fi
#Disable BCL
echo Disabling BCL and Removing Perfd
if [ -e "/sys/devices/soc/soc:qcom,bcl/mode" ]; then
echo -n disable > /sys/devices/soc/soc:qcom,bcl/mode
fi
#Enable Core Control and Disable MSM Thermal Throttling allowing for longer sustained performance
echo Disabling Aggressive CPU Thermal Throttling
if [ -e "/sys/module/msm_thermal/core_control/enabled" ]; then
echo 1 > /sys/module/msm_thermal/core_control/enabled
fi
if [ -e "/sys/module/msm_thermal/parameters/enabled" ]; then
echo N > /sys/module/msm_thermal/parameters/enabled
fi
#Tweak HMP Scheduler to feed the Big cluster more tasks
sleep 0.3
#echo Tweaking HMP Scheduler for correcting BIG Cluster utilization
echo 2 > /proc/sys/kernel/sched_window_stats_policy
echo 85 > /proc/sys/kernel/sched_upmigrate
echo 62 > /proc/sys/kernel/sched_downmigrate
echo 5 > /proc/sys/kernel/sched_spill_nr_run
echo 100 > /proc/sys/kernel/sched_spill_load
echo 30 > /proc/sys/kernel/sched_init_task_load
if [ -e "/proc/sys/kernel/sched_heavy_task" ]; then
echo 65 > /proc/sys/kernel/sched_heavy_task
fi
if [ -e "/proc/sys/kernel/sched_enable_power_aware" ]; then
echo 1 > /proc/sys/kernel/sched_enable_power_aware
fi
echo 10 > /proc/sys/kernel/sched_upmigrate_min_nice
echo 4 > /proc/sys/kernel/sched_ravg_hist_size
if [ -e "/proc/sys/kernel/sched_small_wakee_task_load" ]; then
echo 7 > /proc/sys/kernel/sched_small_wakee_task_load
fi
if [ -e "/proc/sys/kernel/sched_wakeup_load_threshold" ]; then
echo 110 > /proc/sys/kernel/sched_wakeup_load_threshold
fi
if [ -e "/proc/sys/kernel/sched_small_task" ]; then
echo 7 > /proc/sys/kernel/sched_small_task
fi
if [ -e "/proc/sys/kernel/sched_big_waker_task_load" ]; then
echo 35 > /proc/sys/kernel/sched_big_waker_task_load
fi
echo 950000 > /proc/sys/kernel/sched_rt_runtime_us
echo 1000000 > /proc/sys/kernel/sched_rt_period_us
if [ -e "/proc/sys/kernel/sched_migration_fixup" ]; then
echo 1 > /proc/sys/kernel/sched_migration_fixup
fi
if [ -e "/proc/sys/kernel/sched_freq_dec_notify" ]; then
echo 410000 > /proc/sys/kernel/sched_freq_dec_notify
fi
if [ -e "/proc/sys/kernel/sched_freq_inc_notify" ]; then
echo 600000 > /proc/sys/kernel/sched_freq_inc_notify
fi
if [ -e "/proc/sys/kernel/sched_boost" ]; then
echo 0 > /proc/sys/kernel/sched_boost
fi
#Tweaks for other various Settings
sleep 0.5
echo "=========================================="
echo Tweaking other various Settings
echo ·I/O Values
if [ -d /sys/block/dm-0 ] || [ -d /sys/devices/virtual/block/dm-0 ]; then
if [ -e /sys/devices/virtual/block/dm-0/queue/scheduler ]; then
DM_PATH=/sys/devices/virtual/block/dm-0/queue
fi
if [ -e /sys/block/dm-0/queue/scheduler ]; then
DM_PATH=/sys/block/dm-0/queue
fi
string=/sys/devices/virtual/block/dm-0/queue/scheduler;
Zen_Available=false;
if $BB grep 'zen' $string; then
Zen_Available=true;
fi
if [ "$Zen_Available" == "true" ]; then
if [ -e $DM_PATH/scheduler_hard ]; then
echo zen > $DM_PATH/scheduler_hard
fi
echo zen > $DM_PATH/scheduler
sleep 2
echo 300 > $DM_PATH/iosched/sync_expire
echo 2800 > $DM_PATH/iosched/async_expire
echo 14 > $DM_PATH/iosched/fifo_batch
chmod 644 $DM_PATH/iosched/sync_expire
echo 300 > $DM_PATH/iosched/sync_expire
fi
if [ "$Zen_Available" = "false" ]; then
if grep -q 'ro.build.flavor=lineage_oneplus3-userdebug' /system/build.prop; then
echo ZEN not avalible, setting 'Noop' instead...
if [ -e $DM_PATH/scheduler_hard ]; then
echo noop > $DM_PATH/scheduler_hard
fi
echo noop > $DM_PATH/scheduler
else
echo ZEN not avalible, setting 'CFQ' instead...
if [ -e $DM_PATH/scheduler_hard ]; then
echo cfq > $DM_PATH/scheduler_hard
fi
echo cfq > $DM_PATH/scheduler
fi
fi
fi
for i in /sys/block/../devices/soc/624000.ufshc/host0/target0:0:0/0:0:0:[0-4]/block/*/queue; do
string4=$($BB readlink -f $i/scheduler | cut -d 'q' -f1 | cut -d 'k' -f2 | cut -d '/' -f2 | tr a-z A-Z)
string5=$($BB cat $i/scheduler | cut -d ']' -f1 | cut -d '[' -f2 | $BB tr a-z A-Z)
if [ "$string5" == "NOOP" ]; then
echo "Leaving $string4 block at default $string5"
echo ""
sleep 0.1
fi
if [ "$string5" != "NOOP" ]; then
echo "Changing $string4 block I/O scheduler"
if [ -e $i/scheduler_hard ]; then
echo zen > $i/scheduler_hard
fi
echo zen > $i/scheduler
echo ""
sleep 2
# Initialize string 6 to avoid reference conflicts
string6=$($BB cat $i/scheduler | cut -d ']' -f1 | cut -d '[' -f2)
if [ "$string6" == "zen" ]; then
echo 300 > $i/iosched/sync_expire
echo 2800 > $i/iosched/async_expire
echo 14 > $i/iosched/fifo_batch
chmod 644 $i/iosched/sync_expire
echo 300 > $i/iosched/sync_expire
fi
fi
done
if [ -e "$DM_PATH/iostats" ]; then
echo 0 > $DM_PATH/iostats
fi
if [ -e "$DM_PATH/rq_affinity" ]; then
echo 1 > $DM_PATH/rq_affinity
fi
if [ -e "/sys/block/dm-0/bdi/read_ahead_kb" ]; then
echo 512 > /sys/devices/virtual/block/dm-0/bdi/read_ahead_kb
fi
if [ -e "/sys/block/sda/bdi/read_ahead_kb" ]; then
echo 512 > /sys/block/sda/bdi/read_ahead_kb
fi
echo ·Memory Values
echo 0 > /proc/sys/vm/swappiness
echo 100 > /proc/sys/vm/vfs_cache_pressure
echo 80 > /proc/sys/vm/dirty_ratio
echo 20 > /proc/sys/vm/dirty_background_ratio
echo 4096 > /proc/sys/vm/min_free_kbytes
echo 100 > /proc/sys/vm/dirty_expire_centisecs
echo 250 > /proc/sys/vm/dirty_writeback_centisecs
echo 0 > /proc/sys/vm/oom_kill_allocating_task
echo 3 > /proc/sys/vm/page-cluster
if [ -e "/sys/module/lowmemorykiller/parameters/enable_adaptive_lmk" ]; then
chmod 666 /sys/module/lowmemorykiller/parameters/enable_adaptive_lmk
chown root /sys/module/lowmemorykiller/parameters/enable_adaptive_lmk
echo 0 > /sys/module/lowmemorykiller/parameters/enable_adaptive_lmk
fi
if [ -e "/sys/module/lowmemorykiller/parameters/enable_adaptive_lmk" ]; then
echo 0 > /sys/module/lowmemorykiller/parameters/enable_adaptive_lmk
else
echo ' *Adaptive LMK is not present on your Kernel* '
fi
if [ -e "/sys/module/lowmemorykiller/parameters/minfree" ]; then
echo 23939,44091,58788,73485,88182,102879 > /sys/module/lowmemorykiller/parameters/minfree
else
echo ' *LMK cannot currently be modified on your Kernel* '
fi
echo ·TCP Values
string2=/proc/sys/net/ipv4/tcp_available_congestion_control
if grep 'westwood' $string2; then
echo westwood > /proc/sys/net/ipv4/tcp_congestion_control
else
echo Westwood not avilable, using Cubic
echo cubic > /proc/sys/net/ipv4/tcp_congestion_control
fi
#Tweaking GPU
sleep 0.4
echo GPU Tweaking
echo msm-adreno-tz > /sys/devices/soc/b00000.qcom,kgsl-3d0/devfreq/b00000.qcom,kgsl-3d0/governor
if grep -q 'ro.build.version.sdk=25' /system/build.prop; then
if grep -q 'ro.build.flavor=lineage_oneplus3-userdebug' /system/build.prop; then
echo 510000000 > /sys/class/kgsl/kgsl-3d0/max_gpuclk
else
echo 560000000 > /sys/class/kgsl/kgsl-3d0/max_gpuclk
fi
fi
if grep -q 'ro.build.version.sdk=24' /system/build.prop; then
if grep -q 'ro.build.flavor=lineage_oneplus3-userdebug' /system/build.prop; then
echo 510000000 > /sys/class/kgsl/kgsl-3d0/max_gpuclk
else
echo 560000000 > /sys/class/kgsl/kgsl-3d0/max_gpuclk
fi
fi
if grep -q 'ro.build.version.sdk=23' /system/build.prop; then
if grep -q 'ro.build.flavor=lineage_oneplus3-userdebug' /system/build.prop; then
echo 560000000 > /sys/devices/soc/b00000.qcom,kgsl-3d0/devfreq/b00000.qcom,kgsl-3d0/max_freq
else
echo 560000000 > /sys/devices/soc/b00000.qcom,kgsl-3d0/devfreq/b00000.qcom,kgsl-3d0/max_freq
fi
else
if grep -q 'ro.build.flavor=lineage_oneplus3-userdebug' /system/build.prop; then
echo 510000000 > /sys/devices/soc/b00000.qcom,kgsl-3d0/devfreq/b00000.qcom,kgsl-3d0/max_freq
else
echo 560000000 > /sys/devices/soc/b00000.qcom,kgsl-3d0/devfreq/b00000.qcom,kgsl-3d0/max_freq
fi
fi
sleep 1
echo ------------------------------------------------------------
echo 'Project Zhana v4.3' Successfully Applied!
echo "Project Zhana Battery" > /data/system/current_profile
echo You may now tweak them further
echo using EXKM or Kernel Adiutor
echo ------------------------------------------------------------
echo ""
echo " Done, this will be automatically closed..."
sleep 4
#################################################
#Modded by Asiier
#Please say thanks and give proper credits if you're using this profile.
#Credits
#*soniCron *Alcolawl *RogerF81 *Patalao *Mostafa Wael *Senthil360 and all of those that have share their profiles on Nexus 5X/6P Advanced Interactive Tweaks respective threads.
Important are:
Small Cores Tweaks.
echo 70 480000:65 556800:75 729600:82 960000:86 1036800:2 1228800:99 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
echo 220000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/timer_slack
echo 307200 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/hispeed_freq
echo 100000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/timer_rate
echo 0 729600:76000 960000:99000 1228800:150000 1478400:170000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/above_hispeed_delay
echo 155 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/go_hispeed_load
echo 22000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/min_sample_time
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/max_freq_hysteresis
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/ignore_hispeed_on_notif
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/boost
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/fast_ramp_down
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/align_windows
echo 1 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/use_migration_notif
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/use_sched_load
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/boostpulse_duration
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/io_is_busy
if [ -e "/sys/devices/system/cpu/cpu0/cpufreq/interactive/enable_prediction" ]; then
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/interactive/enable_prediction
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/enable_prediction
fi
Big Cores Tweaks:
echo 65 940800:80 1036800:2 1401600:95 1824000:98 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
echo 140000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/timer_slack
echo 1401600 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/hispeed_freq
echo 65000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/timer_rate
echo 32000 940800:85000 1248000:96000 1401600:88000 1632000:80000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/above_hispeed_delay
echo 99 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/go_hispeed_load
echo 11000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/min_sample_time
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/max_freq_hysteresis
echo 1 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/ignore_hispeed_on_notif
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/boost
echo 1 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/fast_ramp_down
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/align_windows
echo 1 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/use_migration_notif
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/use_sched_load
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/boostpulse_duration
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/io_is_busy
if [ -e "/sys/devices/system/cpu/cpu2/cpufreq/interactive/enable_prediction" ]; then
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/interactive/enable_prediction
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/enable_prediction
fi
#Enable Input Boost for LITTLE cluster @729MHz and for BIG cluster @729Hz for 100ms
echo Non-Lineage ROM detected
echo Applying appropriate values.
echo Enabling Input Boost at 729 MHz for the LITTLE cluster and at 0 MHz for the BIG Cluster
if [ -e "/sys/module/cpu_boost/parameters/input_boost_freq" ]; then
chmod 644 /sys/module/cpu_boost/parameters/input_boost_freq
echo 0:729600 1:0 2:0 3:0 > /sys/module/cpu_boost/parameters/input_boost_freq
chmod 644 /sys/module/cpu_boost/parameters/input_boost_ms
echo 77 > /sys/module/cpu_boost/parameters/input_boost_ms
else
echo "*Input Boost is not avalible for your Kernel*"
fi
#echo Tweaking HMP Scheduler for correcting BIG Cluster utilization
echo 2 > /proc/sys/kernel/sched_window_stats_policy
echo 85 > /proc/sys/kernel/sched_upmigrate
echo 62 > /proc/sys/kernel/sched_downmigrate
echo 5 > /proc/sys/kernel/sched_spill_nr_run
echo 100 > /proc/sys/kernel/sched_spill_load
echo 30 > /proc/sys/kernel/sched_init_task_load
it prefers Zen, if not available goes to noop or CFQ
Some Memory tweaks..
cho ·Memory Values
echo 0 > /proc/sys/vm/swappiness
echo 100 > /proc/sys/vm/vfs_cache_pressure
echo 80 > /proc/sys/vm/dirty_ratio
echo 20 > /proc/sys/vm/dirty_background_ratio
echo 4096 > /proc/sys/vm/min_free_kbytes
echo 100 > /proc/sys/vm/dirty_expire_centisecs
echo 250 > /proc/sys/vm/dirty_writeback_centisecs
echo 0 > /proc/sys/vm/oom_kill_allocating_task
echo 3 > /proc/sys/vm/page-cluster
tries to set TCP to westwood if not cubic.
echo msm-adreno-tz > /sys/devices/soc/b00000.qcom,kgsl-3d0/devfreq/b00000.qcom,kgsl-3d0/governor
Oh... and the whole zip is made for SDK25 or lower so not really O compatible.
So yeah... you'd better set the values you'd want manually instead of relying on a outdated all in one wonder script.

timbohobbs said:
Are you using stock elemental x settings or other ?
Click to expand...
Click to collapse
Stock

Haldi4803 said:
Important are:
Small Cores Tweaks.
echo 70 480000:65 556800:75 729600:82 960000:86 1036800:2 1228800:99 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/target_loads
echo 220000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/timer_slack
echo 307200 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/hispeed_freq
echo 100000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/timer_rate
echo 0 729600:76000 960000:99000 1228800:150000 1478400:170000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/above_hispeed_delay
echo 155 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/go_hispeed_load
echo 22000 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/min_sample_time
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/max_freq_hysteresis
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/ignore_hispeed_on_notif
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/boost
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/fast_ramp_down
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/align_windows
echo 1 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/use_migration_notif
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/use_sched_load
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/boostpulse_duration
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/io_is_busy
if [ -e "/sys/devices/system/cpu/cpu0/cpufreq/interactive/enable_prediction" ]; then
chmod 644 /sys/devices/system/cpu/cpu0/cpufreq/interactive/enable_prediction
echo 0 > /sys/devices/system/cpu/cpu0/cpufreq/interactive/enable_prediction
fi
Big Cores Tweaks:
echo 65 940800:80 1036800:2 1401600:95 1824000:98 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/target_loads
echo 140000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/timer_slack
echo 1401600 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/hispeed_freq
echo 65000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/timer_rate
echo 32000 940800:85000 1248000:96000 1401600:88000 1632000:80000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/above_hispeed_delay
echo 99 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/go_hispeed_load
echo 11000 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/min_sample_time
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/max_freq_hysteresis
echo 1 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/ignore_hispeed_on_notif
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/boost
echo 1 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/fast_ramp_down
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/align_windows
echo 1 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/use_migration_notif
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/use_sched_load
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/boostpulse_duration
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/io_is_busy
if [ -e "/sys/devices/system/cpu/cpu2/cpufreq/interactive/enable_prediction" ]; then
chmod 644 /sys/devices/system/cpu/cpu2/cpufreq/interactive/enable_prediction
echo 0 > /sys/devices/system/cpu/cpu2/cpufreq/interactive/enable_prediction
fi
#Enable Input Boost for LITTLE cluster @729MHz and for BIG cluster @729Hz for 100ms
echo Non-Lineage ROM detected
echo Applying appropriate values.
echo Enabling Input Boost at 729 MHz for the LITTLE cluster and at 0 MHz for the BIG Cluster
if [ -e "/sys/module/cpu_boost/parameters/input_boost_freq" ]; then
chmod 644 /sys/module/cpu_boost/parameters/input_boost_freq
echo 0:729600 1:0 2:0 3:0 > /sys/module/cpu_boost/parameters/input_boost_freq
chmod 644 /sys/module/cpu_boost/parameters/input_boost_ms
echo 77 > /sys/module/cpu_boost/parameters/input_boost_ms
else
echo "*Input Boost is not avalible for your Kernel*"
fi
#echo Tweaking HMP Scheduler for correcting BIG Cluster utilization
echo 2 > /proc/sys/kernel/sched_window_stats_policy
echo 85 > /proc/sys/kernel/sched_upmigrate
echo 62 > /proc/sys/kernel/sched_downmigrate
echo 5 > /proc/sys/kernel/sched_spill_nr_run
echo 100 > /proc/sys/kernel/sched_spill_load
echo 30 > /proc/sys/kernel/sched_init_task_load
it prefers Zen, if not available goes to noop or CFQ
Some Memory tweaks..
cho ·Memory Values
echo 0 > /proc/sys/vm/swappiness
echo 100 > /proc/sys/vm/vfs_cache_pressure
echo 80 > /proc/sys/vm/dirty_ratio
echo 20 > /proc/sys/vm/dirty_background_ratio
echo 4096 > /proc/sys/vm/min_free_kbytes
echo 100 > /proc/sys/vm/dirty_expire_centisecs
echo 250 > /proc/sys/vm/dirty_writeback_centisecs
echo 0 > /proc/sys/vm/oom_kill_allocating_task
echo 3 > /proc/sys/vm/page-cluster
tries to set TCP to westwood if not cubic.
echo msm-adreno-tz > /sys/devices/soc/b00000.qcom,kgsl-3d0/devfreq/b00000.qcom,kgsl-3d0/governor
Oh... and the whole zip is made for SDK25 or lower so not really O compatible.
So yeah... you'd better set the values you'd want manually instead of relying on a outdated all in one wonder script.
Click to expand...
Click to collapse
That would work if I knew how to set all those values. For me though I do not.

So i was checking this out and in the FAQ thread here: https://forum.xda-developers.com/showpost.php?p=69037152&postcount=3
Near the top it mentions the HTC10 with a link that explains why it doesn't work or doesn't work as well on an HTC device, linked here: https://forum.xda-developers.com/showpost.php?p=70815496&postcount=2864
The long and short of it is I guess HTC uses there own proprietary pnp manager. But it does go on to say that someone else took the work being done with AKT and made a unified kernel tweak, linked here: https://forum.xda-developers.com/htc-10/development/advanced-interactive-governor-tweaks-t3543589 Which i guess works for anything including HTC's stock kernel.
whew........ So i guess my question first of all is are you using AKT, or are you using Soilwork: Unified kernel-tweaks?
I guess the next question is those of us using modded kernel (cleanslate and Elemental X) Do those kernels have HTC's proprietary pnp manager turned on and they are just tweaking it, or do they shut it off completely and go there own route.
If they shut it off completely then it sounds like AKT is the way to go, but if they don't are are just tweaking HTC's pnp manager, it sounds like the Soilwork tweak is the way to go.
BTW i also use Leedoird, but i'm rocking the CleanSlate kernel atm.
Void4ever

void4ever said:
So i was checking this out and in the FAQ thread here: https://forum.xda-developers.com/showpost.php?p=69037152&postcount=3
Near the top it mentions the HTC10 with a link that explains why it doesn't work or doesn't work as well on an HTC device, linked here: https://forum.xda-developers.com/showpost.php?p=70815496&postcount=2864
The long and short of it is I guess HTC uses there own proprietary pnp manager. But it does go on to say that someone else took the work being done with AKT and made a unified kernel tweak, linked here: https://forum.xda-developers.com/htc-10/development/advanced-interactive-governor-tweaks-t3543589 Which i guess works for anything including HTC's stock kernel.
whew........ So i guess my question first of all is are you using AKT, or are you using Soilwork: Unified kernel-tweaks?
I guess the next question is those of us using modded kernel (cleanslate and Elemental X) Do those kernels have HTC's proprietary pnp manager turned on and they are just tweaking it, or do they shut it off completely and go there own route.
If they shut it off completely then it sounds like AKT is the way to go, but if they don't are are just tweaking HTC's pnp manager, it sounds like the Soilwork tweak is the way to go.
BTW i also use Leedoird, but i'm rocking the CleanSlate kernel atm.
Void4ever
Click to expand...
Click to collapse
Using AKT. And enabled through terminal.And no I didn't disable pnp mgr, I'm guessing it overrides it. And soilwork won't flash. Akt is working fine for me no reboots or massive drains or wakelocks.No excessive heat either running cool as a cucumber,so until pnp is updated I chose to use this route. I'm getting better averages than I was on Nougat. 4.5 hrs on screen currently 27% battery remaining and 16 hours off charger. Try it and see what you think.

mattie_49 said:
Using AKT. And enabled through terminal.And no I didn't disable pnp mgr, I'm guessing it overrides it. And soilwork won't flash. Akt is working fine for me no reboots or massive drains or wakelocks.No excessive heat either running cool as a cucumber,so until pnp is updated I chose to use this route. I'm getting better averages than I was on Nougat. 4.5 hrs on screen currently 27% battery remaining and 16 hours off charger. Try it and see what you think.
Click to expand...
Click to collapse
Hi, do you think this would work on Nougat? I have random reboots at 40% battery left.

NickDVS said:
Hi, do you think this would work on Nougat? I have random reboots at 40% battery left.
Click to expand...
Click to collapse
I'm sure. Try and see

I've done all of this before & it only helps slightly. The drain is related to HTC's framework & it's dialer, and the only way to truly stop the drain is to use airplane mode...which kind of defeats the purpose of it being a phone.
This battery issue is non-existent with LineageOS 15.1 & AOSiP 8.1, running on Oreo firmware. Both of those ROMs work fine, but still have bugs: bottom speaker barely works & Bluetooth issues.

mattie_49 said:
Using AKT. And enabled through terminal.And no I didn't disable pnp mgr, I'm guessing it overrides it. And soilwork won't flash. Akt is working fine for me no reboots or massive drains or wakelocks.No excessive heat either running cool as a cucumber,so until pnp is updated I chose to use this route. I'm getting better averages than I was on Nougat. 4.5 hrs on screen currently 27% battery remaining and 16 hours off charger. Try it and see what you think.
Click to expand...
Click to collapse
I am o. Leedroid 5.2 with stock kernel tweaked by leedroid, can I install a stock stock kernel and what rom do you have?

Is this AKT still work after reboot? Or we must re-enable it after reboot?

fresh777 said:
Is this AKT still work after reboot? Or we must re-enable it after reboot?
Click to expand...
Click to collapse
Must use a terminal emulator. Type su enter
Then type AKT then it's self explainable, choose your profile.

mattie_49 said:
Must use a terminal emulator. Type su enter
Then type AKT then it's self explainable, choose your profile.
Click to expand...
Click to collapse
Thanks for the reply. I mean after run AKT from terminal and done. For the next reboot, i must repeat the step or not?

fresh777 said:
Thanks for the reply. I mean after run AKT from terminal and done. For the next reboot, i must repeat the step or not?
Click to expand...
Click to collapse
No. All done till you wanna change profiles if at all. Terminal will tell you what profile is active after AKT enter

mattie_49 said:
No. All done till you wanna change profiles if at all. Terminal will tell you what profile is active after AKT enter
Click to expand...
Click to collapse
Thank you. I just use this in aosip 8.1 rom. Don't see any improvement for battery life. But for hot issue, i didn't got this issue when use AKT.

Ninja X said:
I am o. Leedroid 5.2 with stock kernel tweaked by leedroid, can I install a stock stock kernel and what rom do you have?
Click to expand...
Click to collapse
the stock kernel in leedroid is not tweaked, you either have the actual stock kernel or the cleanslate kernel.

Oooh.

General Play-systemupdate 20220118

I received yet another Play-systemupdate today (second one in January).
The date - after update - is still reading "December 1, 2021".
However, the following package was updated:
Code:
--before--
com.google.mainline.telemetry | 2021-11-01S+| (311102024)
--after--
com.google.mainline.telemetry | 2021-11-01S+| (311104004)

Seeing this, I decided to manually check and I got another update too (597 kB), still on December.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Click to expand...
Click to collapse
Click to expand...
Click to collapse

Just checked the play system on my phone. Date is Dec 1, 2021 and no update found.

Is there still no way to force these updates? I am still running December^^

Forgot to mention that it was indeed 599K on size.

Same thing here, update was 597kb and still says December.

This is the first time I checked for a playsystem update since my Nokia 6.1 I forgot about these..

Is there anyway to verify before and after the update, that things are being updated? That would be great.

fil3s said:
This is the first time I checked for a playsystem update since my Nokia 6.1 I forgot about these..
Click to expand...
Click to collapse
Google started Play System updates (previously: Project Mainline) with Android 10 (splitting the firmware updates - taking stuff out of the Android operating system, transforming certain functions as an app to ensure timely updates with third party manufacturers through simple updates through Google Playstore - meaning that will help Android phones get critical and essential updates a lot sooner because none of the changes will require a system update from the phone manufacturer).

Alekos said:
Is there anyway to verify before and after the update, that things are being updated? That would be great.
Click to expand...
Click to collapse
Check this link:
Google starts detailing what's new in its monthly Google Play system updates
Now you will know which exact update to blame when something breaks
www.androidpolice.com

foobar66 said:
Check this link:
Google starts detailing what's new in its monthly Google Play system updates
Now you will know which exact update to blame when something breaks
www.androidpolice.com
Click to expand...
Click to collapse
I've read that. I've been disappointed actually in how integrated Play Services is getting. So many things are now part of Play Services its making Android Forks harder to use without GAPPS. Anyway that's a different issue altogether.
I was more interested in your op about the files that were changed on the system. I commented on another post that System Update has had an issue for more than 2 years (on some pixels like I have experienced) where after it updates it reverts to the same (or sometimes an older) date/month. I had a case open with Google Support since last May but they stopped responding.
You have come closest to providing specific changes after this specific update, than I've seen in the past few years. I was hoping maybe for a before and after of some sort, to verify that the Play System update actually updated, and that the date is wrong. I had the date be behind over 6 months at some points. Wiping, flashing original firmware builds etc didn't fix it. It eventually got resolved after A12 for my 2 devices (Pixel 3xl) but I also had it be behind 2 months in December on my 6 Pro.

It is actually a (reasonably) simple linux/bash script which I run before/after upgrade. Then do a 'tkdiff' (if you know what that means) to visualize the deltas. Source code (feel free to (re)use).
Code:
#!/bin/bash
display_usage() {
echo "usage: $0 [{system|user}] [{path|pkg}] [{disabled|enabled}] [<filter>] ($1)"
}
SCNT=0
UCNT=0
PACNT=0
PKCNT=0
DCNT=0
ECNT=0
# by default we put package in first column
PPATH=false
# FLAGS1 selects between user (-3) and system (-s)
FLAGS1=""
# FLAGS2 selects between disabled (-d) and enabled (-e)
FLAGS2=""
# by default there is no grep filter
FCNT=0
FILTER=0
while [[ $# -gt 0 ]]; do
case $1 in
"user")
if [ $SCNT -eq 1 ]; then
display_usage "'user' and 'system' cannot occur together on the command line"
exit 1
fi
if [ $UCNT -eq 0 ]; then
UCNT=$((UCNT + 1))
FLAGS1="-3"
else
if [ $UCNT -eq 1 ]; then
display_usage "'user' can only occur once on the command line"
exit 1
fi
fi
;;
"system")
if [ $UCNT -eq 1 ]; then
display_usage "'user' and 'system' cannot occur together on the command line"
exit 1
fi
if [ $SCNT -eq 0 ]; then
SCNT=$((SCNT + 1))
FLAGS1="-s"
else
if [ $SCNT -eq 1 ]; then
display_usage "'system' can only occur once on the command line"
exit 1
fi
fi
;;
"enabled")
if [ $DCNT -eq 1 ]; then
display_usage "'enabled' and 'disabled' cannot occur together on the command line"
exit 1
fi
if [ $ECNT -eq 0 ]; then
ECNT=$((ECNT + 1))
FLAGS2="-e"
else
if [ $ECNT -eq 1 ]; then
display_usage "'enabled' can only occur once on the command line"
exit 1
fi
fi
;;
"disabled")
if [ $ECNT -eq 1 ]; then
display_usage "'enabled' and 'disabled' cannot occur together on the command line"
exit 1
fi
if [ $DCNT -eq 0 ]; then
DCNT=$((DCNT + 1))
FLAGS2="-d"
else
if [ $DCNT -eq 1 ]; then
display_usage "'disabled' can only occur once on the command line"
exit 1
fi
fi
;;
"path")
if [ $PKCNT -eq 1 ]; then
display_usage "'path' and 'pkg' cannot occur together on the command line"
exit 1
fi
if [ $PACNT -eq 0 ]; then
PACNT=$((PACNT + 1))
PPATH=true
else
if [ $PACNT -eq 1 ]; then
display_usage "'path' can only occur once on the command line"
exit 1
fi
fi
;;
"pkg")
if [ $PACNT -eq 1 ]; then
display_usage "'path' and 'pkg' cannot occur together on the command line"
exit 1
fi
if [ $PKCNT -eq 0 ]; then
PKCNT=$((PKCNT + 1))
PPATH=false
else
if [ $PKCNT -eq 1 ]; then
display_usage "'ppk' can only occur once on the command line"
exit 1
fi
fi
;;
*)
if [ $FCNT -eq 1 ]; then
display_usage "there can only be 1 filter argument"
exit 1
fi
FCNT=$((FCNT + 1))
FILTER="$1"
;;
esac
shift
done
if [ $FCNT -eq 0 ]; then
pkg=$(adb shell pm list packages $FLAGS1 $FLAGS2 -f | colrm 1 8 | sort)
else
pkg=$(adb shell pm list packages $FLAGS1 $FLAGS2 -f | colrm 1 8 | grep "$FILTER" | sort)
fi
LI=()
for P in $pkg; do
if [ $PPATH == "true" ]; then
# just push the entry <file>=<package>
LI+=("$P")
else
# extract filename and packagename and concat them
# so each entry looks like <package>=<filename>
P1=`echo $P | sed 's/apk=/apk /g' | awk '{print $1}'`
P2=`echo $P | sed 's/apk=/apk /g' | awk '{print $2}'`
LI+=("$P2=$P1")
fi
done
rm -rf /tmp/pkgdata
touch /tmp/pkgdata
for P in "${LI[@]:0}"; do
echo "$P" >> /tmp/pkgdata
done
for P in `sort /tmp/pkgdata | grep -v SwiftBlack | grep -v SwiftDark`; do
if [ $PPATH == true ]; then
P1=`echo $P | sed 's/apk=/apk /g' | awk '{print $1}'`
P2=`echo $P | sed 's/apk=/apk /g' | awk '{print $2}' | sed -e 's/ //g'`
else
P1=`echo $P | sed 's%=/% /%g' | awk '{print $2}'`
P2=`echo $P | sed 's%=/% /%g' | awk '{print $1}' | sed -e 's/ //g'`
fi
VER=`adb shell dumpsys package $P2 | grep versionName | head -n 1 | sed -e 's/versionName=//g' | sed -e 's/ //g' | cut -c-15`
VERC=`adb shell dumpsys package $P2 | grep versionCode | head -n 1 | awk '{print $1}' | sed 's/versionCode=//g' | cut -c-15`
if [ $PPATH == true ]; then
# argument was not supplied, it means file name is before the = sign
printf "%-115s |%15s| %-s\n" "$P1" "$VER" "$P2"
else
printf "%-65s |%15s|%12s| %-10s\n" "$P2" "$VER" "($VERC)" "$P1"
fi
done
Run it from the linux command line with:
Code:
> apackages system > before-update
Then apply Google system update, then:
Code:
> apackages system > after-update
> tkdiff before-update after-update
Iḿ not a Windows guy, but I guess it is not so complicated to turn this into a .bat script which you can run from DOS/Powershell under Windows. You must have working adb though.
The script has some command line args:
Code:
system|user: filter on system packages or user packages
enabled|disabled: filter on packages which are enabled or disabled
pkg|path: outputs the path first or package name first
<string> script will filter packages that match the string (e.g. 'com.google.android' will filter those that have com.google.android in their package name)
Sample output (package name, version name, version code, path in Android file system):
Code:
com.android.ons | 12| (31)| /system/priv-app/ONS/ONS.apk
com.android.phone.auto_generated_rro_product__ | 1.0| (1)| /product/overlay/TeleService__auto_generated_rro_product.apk
com.android.phone.auto_generated_rro_vendor__ | 1.0| (1)| /vendor/overlay/TeleService__auto_generated_rro_vendor.apk
com.android.phone | 12| (31)| /system/priv-app/TeleService/TeleService.apk
com.android.printspooler | 12| (31)| /system/app/PrintSpooler/PrintSpooler.apk
com.android.providers.blockednumber | 12| (31)| /system/priv-app/BlockedNumberProvider/BlockedNumberProvider.apk
com.android.providers.calendar | 12| (31)| /system/priv-app/CalendarProvider/CalendarProvider.apk
com.android.providers.contacts.auto_generated_rro_product__ | 1.0| (1)| /product/overlay/ContactsProvider__auto_generated_rro_product.apk

foobar66 said:
It is actually a (reasonably) simple linux/bash script which I run before/after upgrade. Then do a 'tkdiff' (if you know what that means) to visualize the deltas. Source code (feel free to (re)use).
Code:
#!/bin/bash
display_usage() {
echo "usage: $0 [{system|user}] [{path|pkg}] [{disabled|enabled}] [<filter>] ($1)"
}
SCNT=0
UCNT=0
PACNT=0
PKCNT=0
DCNT=0
ECNT=0
# by default we put package in first column
PPATH=false
# FLAGS1 selects between user (-3) and system (-s)
FLAGS1=""
# FLAGS2 selects between disabled (-d) and enabled (-e)
FLAGS2=""
# by default there is no grep filter
FCNT=0
FILTER=0
while [[ $# -gt 0 ]]; do
case $1 in
"user")
if [ $SCNT -eq 1 ]; then
display_usage "'user' and 'system' cannot occur together on the command line"
exit 1
fi
if [ $UCNT -eq 0 ]; then
UCNT=$((UCNT + 1))
FLAGS1="-3"
else
if [ $UCNT -eq 1 ]; then
display_usage "'user' can only occur once on the command line"
exit 1
fi
fi
;;
"system")
if [ $UCNT -eq 1 ]; then
display_usage "'user' and 'system' cannot occur together on the command line"
exit 1
fi
if [ $SCNT -eq 0 ]; then
SCNT=$((SCNT + 1))
FLAGS1="-s"
else
if [ $SCNT -eq 1 ]; then
display_usage "'system' can only occur once on the command line"
exit 1
fi
fi
;;
"enabled")
if [ $DCNT -eq 1 ]; then
display_usage "'enabled' and 'disabled' cannot occur together on the command line"
exit 1
fi
if [ $ECNT -eq 0 ]; then
ECNT=$((ECNT + 1))
FLAGS2="-e"
else
if [ $ECNT -eq 1 ]; then
display_usage "'enabled' can only occur once on the command line"
exit 1
fi
fi
;;
"disabled")
if [ $ECNT -eq 1 ]; then
display_usage "'enabled' and 'disabled' cannot occur together on the command line"
exit 1
fi
if [ $DCNT -eq 0 ]; then
DCNT=$((DCNT + 1))
FLAGS2="-d"
else
if [ $DCNT -eq 1 ]; then
display_usage "'disabled' can only occur once on the command line"
exit 1
fi
fi
;;
"path")
if [ $PKCNT -eq 1 ]; then
display_usage "'path' and 'pkg' cannot occur together on the command line"
exit 1
fi
if [ $PACNT -eq 0 ]; then
PACNT=$((PACNT + 1))
PPATH=true
else
if [ $PACNT -eq 1 ]; then
display_usage "'path' can only occur once on the command line"
exit 1
fi
fi
;;
"pkg")
if [ $PACNT -eq 1 ]; then
display_usage "'path' and 'pkg' cannot occur together on the command line"
exit 1
fi
if [ $PKCNT -eq 0 ]; then
PKCNT=$((PKCNT + 1))
PPATH=false
else
if [ $PKCNT -eq 1 ]; then
display_usage "'ppk' can only occur once on the command line"
exit 1
fi
fi
;;
*)
if [ $FCNT -eq 1 ]; then
display_usage "there can only be 1 filter argument"
exit 1
fi
FCNT=$((FCNT + 1))
FILTER="$1"
;;
esac
shift
done
if [ $FCNT -eq 0 ]; then
pkg=$(adb shell pm list packages $FLAGS1 $FLAGS2 -f | colrm 1 8 | sort)
else
pkg=$(adb shell pm list packages $FLAGS1 $FLAGS2 -f | colrm 1 8 | grep "$FILTER" | sort)
fi
LI=()
for P in $pkg; do
if [ $PPATH == "true" ]; then
# just push the entry <file>=<package>
LI+=("$P")
else
# extract filename and packagename and concat them
# so each entry looks like <package>=<filename>
P1=`echo $P | sed 's/apk=/apk /g' | awk '{print $1}'`
P2=`echo $P | sed 's/apk=/apk /g' | awk '{print $2}'`
LI+=("$P2=$P1")
fi
done
rm -rf /tmp/pkgdata
touch /tmp/pkgdata
for P in "${LI[@]:0}"; do
echo "$P" >> /tmp/pkgdata
done
for P in `sort /tmp/pkgdata | grep -v SwiftBlack | grep -v SwiftDark`; do
if [ $PPATH == true ]; then
P1=`echo $P | sed 's/apk=/apk /g' | awk '{print $1}'`
P2=`echo $P | sed 's/apk=/apk /g' | awk '{print $2}' | sed -e 's/ //g'`
else
P1=`echo $P | sed 's%=/% /%g' | awk '{print $2}'`
P2=`echo $P | sed 's%=/% /%g' | awk '{print $1}' | sed -e 's/ //g'`
fi
VER=`adb shell dumpsys package $P2 | grep versionName | head -n 1 | sed -e 's/versionName=//g' | sed -e 's/ //g' | cut -c-15`
VERC=`adb shell dumpsys package $P2 | grep versionCode | head -n 1 | awk '{print $1}' | sed 's/versionCode=//g' | cut -c-15`
if [ $PPATH == true ]; then
# argument was not supplied, it means file name is before the = sign
printf "%-115s |%15s| %-s\n" "$P1" "$VER" "$P2"
else
printf "%-65s |%15s|%12s| %-10s\n" "$P2" "$VER" "($VERC)" "$P1"
fi
done
Run it from the linux command line with:
Code:
> apackages system > before-update
Then apply Google system update, then:
Code:
> apackages system > after-update
> tkdiff before-update after-update
Iḿ not a Windows guy, but I guess it is not so complicated to turn this into a .bat script which you can run from DOS/Powershell under Windows. You must have working adb though.
The script has some command line args:
Code:
system|user: filter on system packages or user packages
enabled|disabled: filter on packages which are enabled or disabled
pkg|path: outputs the path first or package name first
Sample output (package name, short version, long version, path in Android file system):
Code:
com.android.ons | 12| (31)| /system/priv-app/ONS/ONS.apk
com.android.phone.auto_generated_rro_product__ | 1.0| (1)| /product/overlay/TeleService__auto_generated_rro_product.apk
com.android.phone.auto_generated_rro_vendor__ | 1.0| (1)| /vendor/overlay/TeleService__auto_generated_rro_vendor.apk
com.android.phone | 12| (31)| /system/priv-app/TeleService/TeleService.apk
com.android.printspooler | 12| (31)| /system/app/PrintSpooler/PrintSpooler.apk
com.android.providers.blockednumber | 12| (31)| /system/priv-app/BlockedNumberProvider/BlockedNumberProvider.apk
com.android.providers.calendar | 12| (31)| /system/priv-app/CalendarProvider/CalendarProvider.apk
com.android.providers.contacts.auto_generated_rro_product__ | 1.0| (1)| /product/overlay/ContactsProvider__auto_generated_rro_product.apk
Click to expand...
Click to collapse
This is amazing. Love seeing this stuff. I'm not really a script type of guy like you (guy/girl you know what I mean)... but its great to see and totally intrests me.
so can you see a bunch of files that were changed? or I guess you would have to run the script before and after?
this command
tkdiff before-update after-update
for example - how does it find the exact files that were changed?

Alekos said:
This is amazing. Love seeing this stuff. I'm not really a script type of guy like you (guy/girl you know what I mean)... but its great to see and totally intrests me.
so can you see a bunch of files that were changed? or I guess you would have to run the script before and after?
this command
tkdiff before-update after-update
for example - how does it find the exact files that were changed?
Click to expand...
Click to collapse
See previous post. Indeed run the script before/after, pipe the output into a text file, then do a 'diff' on the before/after text file ... but maybe that sounds like chinese if you're not familiar with Linux ...
The script actually uses adb to shell into the Android device and use the package manager (pm shell command) on the device to 'dump' the package data. Then the script picks up the package name, version name, version code and file path.

foobar66 said:
See previous post. Indeed run the script before/after, pipe the output into a text file, then do a 'diff' on the before/after text file ... but maybe that sounds like chinese if you're not familiar with Linux ...
The script actually uses adb to shell into the Android device and use the package manager (pm shell command) on the device to 'dump' the package data. Then the script picks up the package name, version name, version code and file path.
Click to expand...
Click to collapse
yeah it is chinese to me lol. but its all good.
so how many times was the file com.google.mainline.telemetry" changed in December/January? 3 times for 3 updates but no date change?

Alekos said:
yeah it is chinese to me lol. but its all good.
so how many times was the file com.google.mainline.telemetry" changed in December/January? 3 times for 3 updates but no date change?
Click to expand...
Click to collapse
The previous Play-systemupdate update which I received (Jan 6) only updated com.google.android.modulemetadata.

Google Play Store 28.9.12-19 [0] [PR] 421882020 (nodpi) (Android 4.4+) APK Download by Google LLC - APKMirror
Google Play Store 28.9.12-19 [0] [PR] 421882020 (nodpi) (Android 4.4+) APK Download by Google LLC - APKMirror Free and safe Android APK downloads
www.apkmirror.com
EDIT: Nm wont work

Doug8796 said:
Google Play Store 28.9.12-19 [0] [PR] 421882020 (nodpi) (Android 4.4+) APK Download by Google LLC - APKMirror
Google Play Store 28.9.12-19 [0] [PR] 421882020 (nodpi) (Android 4.4+) APK Download by Google LLC - APKMirror Free and safe Android APK downloads
www.apkmirror.com
EDIT: Nm wont work
Click to expand...
Click to collapse
Mine says it's up to date but it's October

Interesting, mine says Jan 1, 2022.

Mine also says Jan 1, 2022 now

Develop Bugs

welcome