Related
[Q] Tried to install Beatmod ICS, stuck on "screensaver" usb and recovery won't work
Hi guys,
I've watched the n00b video and been googling for the last few hours as well as reading through various pages on the XDA forum. I've found a lot of problems that are kinda similar and tried various solutions but don't seem to be quite getting there.
Basically I had Virtuous Affinity as the OS and clockworkmod installed (should be the most up to date versions of both, they were put on no more than a week ago) as well. I also had a backup of current OS and so on on the SD card, as well as the original zip of the rom.
I decide I want to give ICS a go and so I downloaded the betamod ICS and then loaded it. It asked me if I wanted to do a dalvik cache wipe, a dalvik cache + data wipe and a third option I don't recall. I went with the dalvik cache wipe (at the time I was under the impression that was the correct course of action) then put it back in my pocket while ICS installed.
I get my phone out of my pocket later and it's kinda stuck on what looks like (but logically isn't, I'm guessing it was meant to be a splash screen type thing while ICS installed or some such) a screensaver which just loops endlessly. The only thing you can really do is take the battery out and turn her on again, in which case you once again end up in the endless screensaver loop.
I've tried booting to recovery using volume - and the power button and unfortunately it just boots straight into the looping screensaver again.
Getting a bit worried and feeling adventurous I tried seeing what I could do with ADB, however the computer seemed unable to recognise that any device was connected with ADB devices not listing anything.
I've read up a lot and I'm at a loss as to what to do - there's a rom on the SD card and there also should have been a backup but I just can't get it into recovery.
I do have the ability to view the SD card on another device and interact with it, so if there's a potential SD fix, that's certainly not out the window.
But yeah, I'm clueless how to proceed here and very green at the whole rom business. Can anyone advise what I might try to do from here? I don't care what state I end up going back to, or if I lose my data, I can get all that back, I just want the phone in some semblance of basic operation.
I'll be keeping an eye on the thread, if I've left out any pertinent data ask away and thanks in advance for anyone with a clue how I can fix this mess .
EDIT: Post may be better off in ICS thread above and I do apologise if so, I would move it but I seem unable to delete it.
Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.
ik222 said:
Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.
Click to expand...
Click to collapse
I have, it doesn't work. I've left the battery out for a fairly long period. Volume - + power still just brings it back to the "screensaver" loop.
Thanks for the suggestion though.
Turn the phone off completely; pull the battery out for a bit then replace it and don't touch anything. Don't try to turn it on. Plug the phone by usb to your pc (still turned off). At the command prompt in the folder containing adb.exe type "adb reboot recovery" - the phone should power on and go to recovery where you can wipe properly and reflash whatever you want.
You should be able to boot to recovery using the volume down + power button combo (hold the volume-down key, then press and hold the power button and keep both held until you get to the bootloader menu); the only thing that's wrong with your phone is that you've flashed one ROM over another without wiping it first, so the ROM can't load but this shouldn't affect your bootloader or recovery.
Worst case you can flash a RUU which will restore it to the official firmware; you'll then need to re-root and re-install a recovery image to be able to flash custom ROMs again.
Very helpful post, thanks! I'll try all that and see how I go, I'll post if I still have trouble.
Yeah I dunno why I can't boot to recovery it's weird. The volume button wasn't working, so I removed it and am pressing in the volume down portion of the volume button with a pen while holding down the power button. It's possible perhaps I'm not successfully depressing volume down, but I'm 99% sure I am and that that's not it. I am however doing it as you and other guides advise, depress volume down, hold it and then depress power and hold both for about three seconds, no joy!
Anyway, as said, I'll try what you're recommending and see how I go. Thanks!
hopscotchjunkie said:
At the command prompt in the folder containing adb.exe type "adb reboot recovery"
Click to expand...
Click to collapse
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.
Ethicistabdiel said:
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.
Click to expand...
Click to collapse
Yeah that was what I meant; I've got a feeling that that only works when the phone is powered off if you had USB debugging activated on the phone beforehand, so if that's not working that might be why.
c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.
Accidental double post, sorry.
You need to try get into recovery mode, where you can do a full wipe and see if that fixes anything.
Firstly, remove your battery then re-install it, your phone should still be turned off at this stage. Press and hold the volume down button, then additionally press and hold the power butter, until something appears on the screen. If the bootloader appears, you can then boot into recovery from there.
If the above fails to work, report back with your results and hopefully something else will be suggested.
Ethicistabdiel said:
c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.
Click to expand...
Click to collapse
Your only other option to get into recovery is the volume-down/power-on combination. Like I said, I can't think why that's not working unless it's related to your missing volume button (maybe it's not maintaining a constant pressure on the button when you're using whatever to press through the hole).
If you still can't get that to work, I would suggest finding a stock RUU and flashing that. It's an .exe file that runs from your PC and will return your ROM, bootloader and radio back to stock. Obviously that means you'll lose root and your custom recovery so you'll need to do all that again from scratch. There's a sticky in the dev section with a link to a thread with various RUUs (it's named something along the lines of "shipped & test ROMs" - I'll check that and link to it once I've dragged myself out of bed to the computer). You'll lose all your data, but if you took a backup beforehand you can restore that once you're back up and running.
//sent from my Desire HD using Tapatalk; all errors entirely intentional.
Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.
http://forum.xda-developers.com/showthread.php?t=824357&page=5
Guessing you mean that as far as the ruu thread. Am downloading a stock rom atm, with shaped internet till tomorrow, meh! Will see how I go. Have a feeling phone was probably Vodafone branded at stock though, so that could make for extra fiddling but yeah, fingers crossed.
If you are able too install a stock-rom you can work from their than install 4EXT recovery
touch than you doen't need the volume buttons.
I downloaded the most recent stock rom on the link above. When I try to install it though, phone off or on, it advises a USB connection error. Is this likely to be because I originally had vodafone stock and need to make a gold card, or should it still at least be recognising it? It does advise not to run any programs on the phone or anything when while installing the update, but of course, as long as my phones turned on it's stuck on the damned screensaver loop.
http://forum.xda-developers.com/archive/index.php/t-841890.html
Gonna give that a go, fingers crossed!
D'oh, just found out my mobile was Three at stock and not Vodafone, the search continues .
Gah, I'm about tearing my hair out here, I want my damned phone back . Stuck using a $79 Huwawei Vodafone thing at the moment and it's so so so awful.
Anyway. I was under the impression that making a goldcard would mean I could RUU a non-Three stock rom on the phone. I made a goldcard following these instructions; http://www.addictivetips.com/mobile/how-to-make-gold-card-for-htc-desire-hd/
Then I turned the phone on as the RUU advises, (meaning it's scrolling through the feckin' "screensaver") and start the process and once again get a USB connection error.
What's the better process at this stage, try and take it back to Three stock? I don't see how I can at the moment, the only Three stock I can find seems to be rom, not RUU, meaning I'd need to load from the phone, which I can't due to no recovery. Or should I keep trying to get the goldcard thing to work, maybe try some different RUU's or something?
I'm open to any other suggestions as well. Had a bit more of a fiddle around with my volume down button, no matter what I do though, I can't get recovery mode. Always boots first to the white HTC screen and then starts the infernal "screensaver" loop.
Ethicistabdiel said:
Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.
Click to expand...
Click to collapse
How come the volume down button be broken. When you were using Affinity Rom weren't you able to use your volume button for music. Remove SD card from phone then press "First - Volume down gently for 2 sec" & press-hold power button when it goes into bootload place your sd card back select option "REBOOT RECOVERY". I think your panicking too much just be patient nothing is wrong, i think your just hurrying it up...
The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .
Ethicistabdiel said:
The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .
Click to expand...
Click to collapse
The only option i can think of is "Fix your volume button from your nearest Service centre". Without that you cant do anything. I am Sorry....
Im able to get into twrp recovery, and fastboot mode but not download mode... I wanted to put the phone back into stock and i thought wiping out everything would do so but i guess not.
Whenever i press the download mode command which i did was volume up down and power then plug into the laptop the 3 buttons will flash but my laptop won recognized it. I tried installing the LG Optimus G drivers but still unable to install it. Also TWRP says that the phone isnt rooted anymore and has no OS.
HelloDominick said:
Im able to get into twrp recovery, and fastboot mode but not download mode... I wanted to put the phone back into stock and i thought wiping out everything would do so but i guess not.
Whenever i press the download mode command which i did was volume up down and power then plug into the laptop the 3 buttons will flash but my laptop won recognized it. I tried installing the LG Optimus G drivers but still unable to install it. Also TWRP says that the phone isnt rooted anymore and has no OS.
Click to expand...
Click to collapse
First off it's Vol Up + Vol Down while powered off and then plug into computer. DO NOT press the power button.
Secondly what ver. of windows and did the computer have any issues prior with connecting to the phone?
There is another fix but it's a bit drastic and wouldn't recommend it at this point.
SlimMan said:
First off it's Vol Up + Vol Down while powered off and then plug into computer. DO NOT press the power button.
Secondly what ver. of windows and did the computer have any issues prior with connecting to the phone?
There is another fix but it's a bit drastic and wouldn't recommend it at this point.
Click to expand...
Click to collapse
oh well that might be the reason why. il try it out..im using windows 7 and it was working before i wiped everything.
link me to that fix if anything thanks
On my phone, Download Mode is only accessed when Vol + and - and power from a powered off state, while any USB cord is plugged in, either to a PC, or a wall charger.
After flashing, i noticed that the phone has some issues powering on and off normally i.e. phone completely died, plug the phone into the charger, screen turns on, phone is theoretically charging, but does not show any charging display icon. Which then forces me to unplug the phone, press and hold the power button for 10 seconds, press and hold the power again to turn the phone on, and immediately plug it into the charger in order to get the phone to normally boot up. I flashed CM 10.2 from the original android dev thread. I think that was just a design flaw that LG had originally, but meh, what can i say.
Q&A?
Sent from my Nexus 4 using xda app-developers app
Hi everyone, today my Elephone p8000 with stock rom (no root nor recovery installed) proposed me an OTA update, and I did it.
After installing the update the phone is stuck at the boot animation logo. If I boot in factory mode (volume down + power button) I am presented with a bunch of options in Chinese, which I don't understand. If I go in recovery mode (volume down + power button) it says "no command".
What can I do? What are my options? Is it bricked?
Yup mine too. Mine has root, with no custom recovery. Get the same boot loop and the sad open Android 'no command'.
Haven't had a chance to dig around for a solution but I suspect it is a case of using the flash tool to wipe and load a standard ROM? Hopefully an easier way.
kevvyboy said:
Yup mine too. Mine has root, with no custom recovery. Get the same boot loop and the sad open Android 'no command'.
Haven't had a chance to dig around for a solution but I suspect it is a case of using the flash tool to wipe and load a standard ROM? Hopefully an easier way.
Click to expand...
Click to collapse
Damn. I had huge problems with the flash tool in the past (I don't have a Windows PC) and the idea of spending the weekend trying to get the damn thing work is not a fun one.
Got this issue too this morning on way to work, I guess my phones useless today until I get home to try and flash it.
seem to be able to get to the boot select screen but nothing is different anyway, also managed to get into a "PCBA" mode that did a load of tests to the phone but thats it.
it now just died, not powering on, think its bricked :crying:
skea said:
it now just died, not powering on, think its bricked :crying:
Click to expand...
Click to collapse
Probably just out of power. Try charging it for a while and/or download and flash entire rom using sp flash except for data-partition so as you don't lose your data.
pitrus- said:
Probably just out of power. Try charging it for a while and/or download and flash entire rom using sp flash except for data-partition so as you don't lose your data.
Click to expand...
Click to collapse
thanks it was out of power lol
I just had the same problem. Did you solved it?
Like, exactly the same... Crazy
Another one
My p8000 also in bootloop after ota update. Only have an old vista PC w8ll dust it off tonight and see what happens
mines doing the same i thought it was too good to be true and it was lol
Cannot get pc (win 10) to install all the drivers, PC cannot see the phone so unable to run flash tool.
Suggestions? I presume the ROM cannot be flashed through the recovery (standard)?
EDIT: Driver package installed by disabling 'driver verification' setting in Windows. Phone only recognised as a MTP USB Device in devide manager, and flash tool does not seem to want to do anything. Might try this on a Win 7 laptop tomorrow. HJow you guys getting on with this?
Success - I Have a Working Phone
(or, How Chest Pains and Rage Focused the Mind)
So. This is what worked for me. Win 10. P8000 bootloop.
1) put p8000 into recovery, chose 'power off'. (I couldn't seem to stop it rebooting using the power button)
2) installed driver pack by disabling the Windows install signed drivers only setting. Rebooted. This turns the setting back on, but the drivers have alrwady been installed, no issue with that.
3) installed the flash tool. Brief panic at Chinese chars, located English. Calmed down.
4) loaded flash tool, with ROM ready to go.
5) this is the biggie, this is what brought it all together.........connected the powered down p8000 via USB and IMMEDIATELY hit the download button in the flash tool - ie BEFORE a new instance of USB bing-bong-device-connected sound.
6) once all downloaded, disconnect phone, reboot. Took an extended time (few mins) to boot, enough time to almost start swearing under my breath, but it just needed some patience.
Now, what I spent some time unsuccessfully trying to fix - needlessly as it turns out - was what my phone appeared under 'Device Manager'. It still lists it as an MTP USB Device under the 'Portable Devices' submenu. It did not seem to matter, as long as all the driver were installed.
I wish you all the best of luck in solving your issues, hopefully some of what I wrote can be helpful.
pitrus- said:
download and flash entire rom using sp flash except for data-partition so as you don't lose your data.
Click to expand...
Click to collapse
I have the same boot loop after ota. I did no backup before, so data partition contains my apps right ?
I never used the flash tool , where should I start , any good link for beginners ?
I read some things about the flash options months ago, must I disable/uncheck some options ?
Thanks for help.
same issue
Hi everyone!
I've got the same issue: I allowed the OTA update to 20151105 firmware release from previous version (20150725), after the upgrade, the phone keeps in a bootloop with a new colored Elephone logo.
I can't find a valid set of drivers, I tried a lot over the night, but windows don't recognize the phone.
PLEASE some kind soul could link a valid driver package to use SP tool ?
thanks a lot in advance!
mr..speed said:
I have the same boot loop after ota. I did no backup before, so data partition contains my apps right ?
I never used the flash tool , where should I start , any good link for beginners ?
I read some things about the flash options months ago, must I disable/uncheck some options ?
Thanks for help.
Click to expand...
Click to collapse
kevvyboy said:
Success - I Have a Working Phone
(or, How Chest Pains and Rage Focused the Mind)
So. This is what worked for me. Win 10. P8000 bootloop.
1) put p8000 into recovery, chose 'power off'. (I couldn't seem to stop it rebooting using the power button)
2) installed driver pack by disabling the Windows install signed drivers only setting. Rebooted. This turns the setting back on, but the drivers have alrwady been installed, no issue with that.
3) installed the flash tool. Brief panic at Chinese chars, located English. Calmed down.
4) loaded flash tool, with ROM ready to go.
5) this is the biggie, this is what brought it all together.........connected the powered down p8000 via USB and IMMEDIATELY hit the download button in the flash tool - ie BEFORE a new instance of USB bing-bong-device-connected sound.
6) once all downloaded, disconnect phone, reboot. Took an extended time (few mins) to boot, enough time to almost start swearing under my breath, but it just needed some patience.
Now, what I spent some time unsuccessfully trying to fix - needlessly as it turns out - was what my phone appeared under 'Device Manager'. It still lists it as an MTP USB Device under the 'Portable Devices' submenu. It did not seem to matter, as long as all the driver were installed.
I wish you all the best of luck in solving your issues, hopefully some of what I wrote can be helpful.
Click to expand...
Click to collapse
kevvyboy said:
Success - I Have a Working Phone
(or, How Chest Pains and Rage Focused the Mind)
So. This is what worked for me. Win 10. P8000 bootloop.
1) put p8000 into recovery, chose 'power off'. (I couldn't seem to stop it rebooting using the power button)
2) installed driver pack by disabling the Windows install signed drivers only setting. Rebooted. This turns the setting back on, but the drivers have alrwady been installed, no issue with that.
3) installed the flash tool. Brief panic at Chinese chars, located English. Calmed down.
4) loaded flash tool, with ROM ready to go.
5) this is the biggie, this is what brought it all together.........connected the powered down p8000 via USB and IMMEDIATELY hit the download button in the flash tool - ie BEFORE a new instance of USB bing-bong-device-connected sound.
6) once all downloaded, disconnect phone, reboot. Took an extended time (few mins) to boot, enough time to almost start swearing under my breath, but it just needed some patience.
Now, what I spent some time unsuccessfully trying to fix - needlessly as it turns out - was what my phone appeared under 'Device Manager'. It still lists it as an MTP USB Device under the 'Portable Devices' submenu. It did not seem to matter, as long as all the driver were installed.
I wish you all the best of luck in solving your issues, hopefully some of what I wrote can be helpful.
Click to expand...
Click to collapse
pretty much did the same thing and it worked!! Cheers!! (also had the rage and it took ages to find english on the tool lol :laugh: )
when you get the android with the "no command" message, let go of the volume and power buttons. Then hold the POWER BUTTON for 1-2 seconds and TAP VOLUME UP while still holding the power button. this will open the recovery options
omg!!
disabling the Windows install signed drivers only setting!!
i thought we wouldnt have to do things like this since Windows 95
Lol
Worked for me
Had I only found this tutorial before yesterday... it took me hours to figure this out.
I can, however, now confirm this works.
Regarding point 5):
(i) Power down phone (ii) start flash tool/go to download tab (iii) select scatter file (iv) hit "download" with no phone attached (v) attach the powered down phone
...and things will be fine. Doing anything fast is not required.
The point is to install SP_Drivers_v2.0 first, as described here. After this, everything goes smooth.
kevvyboy said:
Success - I Have a Working Phone
(or, How Chest Pains and Rage Focused the Mind)
So. This is what worked for me. Win 10. P8000 bootloop.
1) put p8000 into recovery, chose 'power off'. (I couldn't seem to stop it rebooting using the power button)
2) installed driver pack by disabling the Windows install signed drivers only setting. Rebooted. This turns the setting back on, but the drivers have alrwady been installed, no issue with that.
3) installed the flash tool. Brief panic at Chinese chars, located English. Calmed down.
4) loaded flash tool, with ROM ready to go.
5) this is the biggie, this is what brought it all together.........connected the powered down p8000 via USB and IMMEDIATELY hit the download button in the flash tool - ie BEFORE a new instance of USB bing-bong-device-connected sound.
6) once all downloaded, disconnect phone, reboot. Took an extended time (few mins) to boot, enough time to almost start swearing under my breath, but it just needed some patience.
Now, what I spent some time unsuccessfully trying to fix - needlessly as it turns out - was what my phone appeared under 'Device Manager'. It still lists it as an MTP USB Device under the 'Portable Devices' submenu. It did not seem to matter, as long as all the driver were installed.
I wish you all the best of luck in solving your issues, hopefully some of what I wrote can be helpful.
Click to expand...
Click to collapse
What if no Windows?
Edit: Never mind, I got myself a windows computer and succeeded. Thanks for all the orientation!
Hi all,
Thanks a lot for posting a solution to this problem so quickly. I am affected by the same issue. Looking to buy some LSD to better enjoy the psychtrip my phone seems to be stuck in. Also looking to fix the phone.
Unfortunately, I'm running Ubuntu 14.04 LTS. I did find a guide to use the flash tool on Ubuntu, but my phone does not seem to connect. I'm guessing this has something to do with that pack of drivers 2.0, for which I have no equivalent. I would really appreciate any ideas!
I might end up returning my phone to Amazon, though. It's only been a few days since I've had it, and you can imagine that although I was really liking it, I'm beginning to change my mind.
Your advice?
EDIT: I am getting the following error message:
BROM ERROR: S_COM_PORT_OPEN_FAIL (1013)
[COM]: Failed to open COM port.
[HINT]:
I did some googling, but didn't find anything worth mentioning.
yslsl said:
Had I only found this tutorial before yesterday... it took me hours to figure this out.
I can, however, now confirm this works.
Regarding point 5):
(i) Power down phone (ii) start flash tool/go to download tab (iii) select scatter file (iv) hit "download" with no phone attached (v) attach the powered down phone
...and things will be fine. Doing anything fast is not required.
The point is to install SP_Drivers_v2.0 first, as described here. After this, everything goes smooth.
Click to expand...
Click to collapse
Ahh good stuff. Connect phone last after hitting download - thanks for the heads up. Got my wife's p8000 today so will be doing some flashing later.
Cheers!
Hi.
I have a Xiaomi mi5s 64/3 GB in an endless bootloop. Here are the details:
The phone is:
rooted
bootloader unlocked
developer mode enabled
internal storage *not* encrypted
no MIUI account activated
USB debugging on
running the last EU MIUI 9.x development version (don't remember the exact version) with Android 7.0
has TWRP 3.2.1.0 and supersu 2.82
no password is set for unlocking the screen etc.
For some unknown reason the phone suddenly rebooted yesterday and got into an infinite bootloop cycle. I haven't changed any roms recently or done any such flashing. My google play automatic updates were disabled, but a few days ago I manually updated all the apps.
The only odd thing that happened prior to this bootloop, was that when shooting some photos with the google camera mod (same one I've been using for the past few weeks), 2 images were saved as corrupt unreadable files. But that happened a few hours before the bootloop suddenly started.
The current status is:
1. I cannot turn the power off (tried holding the power button, or power button + vol up and down for a very long time --> nothing).
2. I cannot enter recovery mode using vol up + power.
3. I cannot enter EDL using all 3 buttons.
4. If I hold volume down, it enters fastboot but automatically exits from it within 4 seconds (ADB and miflash cannot detect the device in this short period of time). holding the volume down button for a long time has a repating enter-exit-after-4-seconds from the fastboot graphics.
I waited until the battery was completely dead, than started charging it and the status described above was unchanged.
QUESTION 1 - restoring the internal data is my number one priority - does it seem possible here?
To be exact: I want the DCIM folder with the photos+ videos. What should I try now?
QUESTION 2 - I ordered an EDL cable, but am unsure if it supported for my MIUI version. if the EDL cable works, can I force the phone to enter recovery mode from within EDL?
If so - I guess I can copy the internal data to an external USB OTG flash drive I have (that works well with the phone).
If my data is restored, I will then move onto trying to reflash the phone, but at this point this is the least of my worries...
Thanks all.
Anyone?
Maybe it's a problem with the button? I would disassembly the phone and check the hardware.
bedson87 said:
Maybe it's a problem with the button? I would disassembly the phone and check the hardware.
Click to expand...
Click to collapse
I don't know - the buttons don't seem like they are stuck in any way. When I push them, they click back out as usual.
Update - I created an EDL flash cable by stripping the cable gently, exposing the green and black wires, and looping them together - connecting this cable to the phone didn't help either.
Maybe I need to wait for the battery to die so the phone will turn off, connect this cable to the phone, keep the power button pressed while I connect it to the usb port in my PC... what do you think?
I have the same problem with mi 5s which started after update. Don't know what to do.
Took the phone to a local lab - it was all due to a faulty power button module.
Hi there,
I am looking for some guidance on my bricked Pixel 6 Pro.
I transfered the data from my old pixel, but then decided to do a full flash to refresh. Downloaded the stock image from google, used the fastboot-all script to flash the phone, but as soon as it was done, I never reboot. my phone is looking completely dead since.
Attempt # 1
- black screen, with no sound to any actions of response to any key combination (power or volume keys).
- tried holding the power button for 60 secs, no response
- tried holding power and volume down, no response
- tried holding power and volume up, no response
- when I plug the phone on charge, no response. neither the charging display.
Atempt # 2
- Only time the phone shows some sign of life, is when I connect the phone to my PC, it makes a sound of detecting a device, but then instantly it get a disconnect sound, (in 2-3 sec).
- I tried holding the power button, while plugged in. it makes a sound of usb detection, (but no visual response on the phone) after holder for 30 secs, it makes another sound of usb detach.
- While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone.
Not sure, if I have bricked the bootloader, and if yes, what can be done? Any guidance in this regards will be highly appreciated.
Thanks
Call whoever you bought the phone from and do warranty claim.
I struggled with a soft bricked / bootlooping phone after removing Magisk. Although my phone at least booted to bootloader and a connection via fastboot was working, the factory images wouldn't flash properly. Google support couldn't help me and I thought I had to send it to repair.
In the end I could solve the issue by switching to the Android SDK 31. I know your case is different, because your phone is bricked worse than mine was, but you could give it a try.
Baumhouse said:
I struggled with a soft bricked / bootlooping phone after removing Magisk. Although my phone at least booted to bootloader and a connection via fastboot was working, the factory images wouldn't flash properly. Google support couldn't help me and I thought I had to send it to repair.
In the end I could solve the issue by switching to the Android SDK 31. I know your case is different, because your phone is bricked worse than mine was, but you could give it a try.
Click to expand...
Click to collapse
rao_hamza said:
Hi there,
I am looking for some guidance on my bricked Pixel 6 Pro.
I transfered the data from my old pixel, but then decided to do a full flash to refresh. Downloaded the stock image from google, used the fastboot-all script to flash the phone, but as soon as it was done, I never reboot. my phone is looking completely dead since.
Attempt # 1
- black screen, with no sound to any actions of response to any key combination (power or volume keys).
- tried holding the power button for 60 secs, no response
- tried holding power and volume down, no response
- tried holding power and volume up, no response
- when I plug the phone on charge, no response. neither the charging display.
Atempt # 2
- Only time the phone shows some sign of life, is when I connect the phone to my PC, it makes a sound of detecting a device, but then instantly it get a disconnect sound, (in 2-3 sec).
- I tried holding the power button, while plugged in. it makes a sound of usb detection, (but no visual response on the phone) after holder for 30 secs, it makes another sound of usb detach.
- While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone.
Not sure, if I have bricked the bootloader, and if yes, what can be done? Any guidance in this regards will be highly appreciated.
Thanks
Click to expand...
Click to collapse
rao_hamza said:
Hi there,
I am looking for some guidance on my bricked Pixel 6 Pro.
I transfered the data from my old pixel, but then decided to do a full flash to refresh. Downloaded the stock image from google, used the fastboot-all script to flash the phone, but as soon as it was done, I never reboot. my phone is looking completely dead since.
Attempt # 1
- black screen, with no sound to any actions of response to any key combination (power or volume keys).
- tried holding the power button for 60 secs, no response
- tried holding power and volume down, no response
- tried holding power and volume up, no response
- when I plug the phone on charge, no response. neither the charging display.
Atempt # 2
- Only time the phone shows some sign of life, is when I connect the phone to my PC, it makes a sound of detecting a device, but then instantly it get a disconnect sound, (in 2-3 sec).
- I tried holding the power button, while plugged in. it makes a sound of usb detection, (but no visual response on the phone) after holder for 30 secs, it makes another sound of usb detach.
- While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone.
Not sure, if I have bricked the bootloader, and if yes, what can be done? Any guidance in this regards will be highly appreciated.
Thanks
Click to expand...
Click to collapse
Bootloader unlocked?
cultofluna said:
Bootloader unlocked?
Click to expand...
Click to collapse
If I remeber correctly flashing factory images forces you to unlock the device. So yes, the bootloader of rao_hamza's device should be unlocked.
From memory you can revive it through QPST and orher Qualcomm utilities, however hard part is to get the files. the phone is too new and many shops dont have the unlock tools yet.
" While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone. " - this is still good news, as phone is being detected by windows, try to install Qualcomm drivers and see if you can get it to boot into EDL. GOOD LUCK.
Pixel 6 uses Google's own new Tensor chip - so no Qualcomm tools
Like @Baumhouse I went through something similar. Two things for me: it took way longer to hold power and volume down than any other phone I've owned. I was seriously concerned I wasn't going to get there. Two, the factory images all made it to fastbootd and then failed all because I hadn't updated to the latest SDK.
Just throwing this out in hopes you don't have to send it back.
What @ridobe said. Make sure you're using the latest official Google Platform Tools (there's a link in my thread at the top of my signature below if you need it, or just Google for it). If I had a nickel every time someone didn't update the tools when they went to use them...
roirraW edor ehT said:
What @ridobe said. Make sure you're using the latest official Google Platform Tools (there's a link in my thread at the top of my signature below if you need it, or just Google for it). If I had a nickel every time someone didn't update the tools when they went to use them...
Click to expand...
Click to collapse
This and a bad/wrong cable seem to be the most common culprits
ridobe said:
Like @Baumhouse I went through something similar. Two things for me: it took way longer to hold power and volume down than any other phone I've owned. I was seriously concerned I wasn't going to get there. Two, the factory images all made it to fastbootd and then failed all because I hadn't updated to the latest SDK.
Just throwing this out in hopes you don't have to send it back.
Click to expand...
Click to collapse
Any idea how long you had to hold that button combinaiton? I tried longer, maybe 60 sec, but still no response from the phone.
tids2k said:
From memory you can revive it through QPST and orher Qualcomm utilities, however hard part is to get the files. the phone is too new and many shops dont have the unlock tools yet.
" While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone. " - this is still good news, as phone is being detected by windows, try to install Qualcomm drivers and see if you can get it to boot into EDL. GOOD LUCK.
Click to expand...
Click to collapse
What is EDL? and had the Google usb drivers installed, to get the fastboot working.
Baumhouse said:
I struggled with a soft bricked / bootlooping phone after removing Magisk. Although my phone at least booted to bootloader and a connection via fastboot was working, the factory images wouldn't flash properly. Google support couldn't help me and I thought I had to send it to repair.
In the end I could solve the issue by switching to the Android SDK 31. I know your case is different, because your phone is bricked worse than mine was, but you could give it a try.
Click to expand...
Click to collapse
Yes, I don't know who to get into a bootloader in this situation, if that were working I would have some hope.
If you can get to the bootloader you can use google's flashing website, flash.android.com. I just use that to go back to stock, even with an unlocked bootloader.
pysklona said:
If you can get to the bootloader you can use google's flashing website, flash.android.com. I just use that to go back to stock, even with an unlocked bootloader.
Click to expand...
Click to collapse
Thanks @pysklona. you are right, but the problem is I can't get into the bootloader. This is what I am seeking help for.
rao_hamza said:
Thanks @pysklona. you are right, but the problem is I can't get into the bootloader. This is what I am seeking help for.
Click to expand...
Click to collapse
Sorry, misread the post.
@pysklona came here because I'm in the same boat, hard-bricked my device after running the flash-all script. Was using the most recent version of platform tools and the brand new cable that came with the phone.
Was getting the same result, attaching it to a windows pc makes the attached device chime, but disconnects after a few seconds. It came up first as "Setting up Pixel ROM Recovery". I let it sit overnight and now it doesn't auto-disconnect and I get a serial device under com3 on windows. Attaching it to macos gives me a "Pixel ROM Recovery" device. Despite "recovery" in the name, I think it's actually in EDL mode, not recovery mode. No devices come up for adb or fastboot on windows, linux or macos. Screen is completely blank no matter what.
Not being a Qualcomm chip makes this whole process from here a bit of an unknown, but will assume the process for recovery is more or less the same. Looking into QPST/MsmDownloadTool/OpenPST, although as pointed out, I'm not sure any of those tools will work since this isn't a qualcomm chip. MsmDownloadTool is for oneplus, but maybe something can be modded.
ootri said:
@pysklona came here because I'm in the same boat, hard-bricked my device after running the flash-all script. Was using the most recent version of platform tools and the brand new cable that came with the phone.
Was getting the same result, attaching it to a windows pc makes the attached device chime, but disconnects after a few seconds. It came up first as "Setting up Pixel ROM Recovery". I let it sit overnight and now it doesn't auto-disconnect and I get a serial device under com3 on windows. Attaching it to macos gives me a "Pixel ROM Recovery" device. Despite "recovery" in the name, I think it's actually in EDL mode, not recovery mode. No devices come up for adb or fastboot on windows, linux or macos. Screen is completely blank no matter what.
Not being a Qualcomm chip makes this whole process from here a bit of an unknown, but will assume the process for recovery is more or less the same. Looking into QPST/MsmDownloadTool/OpenPST, although as pointed out, I'm not sure any of those tools will work since this isn't a qualcomm chip. MsmDownloadTool is for oneplus, but maybe something can be modded.
Click to expand...
Click to collapse
Thanks for sharing your experience. I just returned the device and got myself a new one.
anyways, i am not sure what is causing this hard brick. thats is something we all should be careful about it.
same thing here. pixel 6 from google store. magisk installed on the december update and i downgraded to the november one using the flash-all.bat script. phone reboots and am told the software is corrupt
reboot back into fastboot mode, run the script again. and get this software is corrupt message again
this time I cant' even boot into fastboot/bootloader mode. and plugging the phone into windows gives me the "pixel rom recovery" message
phone seems dead (black screen, not responding to hardware buttons)
any other solutions than to get it replaced?
Hmm, maybe plug it in to a PC via USB to supply it with power (maybe the battery is down) and just do a very long press of the power button - at least 30 seconds - until the phone starts up. If it does and isn't in fastboot you could try "Power-VolDown" to get into fastboot...
If it just doesn't react to all of this and waiting a bit (in case the battery was at 0% and needs some minimal charge) I think a replacement is the only way to go....
Enddo said:
same thing here. pixel 6 from google store. magisk installed on the december update and i downgraded to the november one using the flash-all.bat script. phone reboots and am told the software is corrupt
reboot back into fastboot mode, run the script again. and get this software is corrupt message again
this time I cant' even boot into fastboot/bootloader mode. and plugging the phone into windows gives me the "pixel rom recovery" message
phone seems dead (black screen, not responding to hardware buttons)
any other solutions than to get it replaced?
Click to expand...
Click to collapse
You could try Official Google Android Flash Tool. It's merely another method of doing what you effectively tried, but from what I've read, it's helped some folks. Sadly, others have reported that the Official Google Pixel Update and Software Repair hasn't been updated for the P6P yet.
If that doesn't help, hang in there. There are others in here who will likely have even better advice.
roirraW edor ehT said:
You could try Official Google Android Flash Tool. It's merely another method of doing what you effectively tried, but from what I've read, it's helped some folks. Sadly, others have reported that the Official Google Pixel Update and Software Repair hasn't been updated for the P6P yet.
If that doesn't help, hang in there. There are others in here who will likely have even better advice.
Click to expand...
Click to collapse
appreciate the links. right now, I can't even get into fastboot/bootloader mode. so neither of those tools detect the phone.
@s3axel the battery definitely isn't low. I charged it up before all this specifically so that I know it had plenty of juice (was at 93% or something).
I'm thinking maybe after letting the battery die, charging it back up will let me boot into a special boot mode
but any other ideas, please, I'm all ears