Hello, I'm new at this
I have a problem with my cell phone, Samsung SM-G928P from Sprint.
I can not install "stock rom" or any rom with odin. :crying:
I tried to download rom stock from sammobile, but it gives me the following error "SW REV. CHECK FAIL.DEVICE: 3, BINARY: 2". I do not know what to do currently I am with "SkyHigh Kernel" & ROM Moar kernel.
I'm desperate. :crying:
Please Help!
eddyzeron said:
Hello, I'm new at this
I have a problem with my cell phone, Samsung SM-G928P from Sprint.
I can not install "stock rom" or any rom with odin. :crying:
I tried to download rom stock from sammobile, but it gives me the following error "SW REV. CHECK FAIL.DEVICE: 3, BINARY: 2". I do not know what to do currently I am with "SkyHigh Kernel" & ROM Moar kernel.
I'm desperate. :crying:
Please Help!
Click to expand...
Click to collapse
What base firmware are you on?
eddyzeron said:
Hello, I'm new at this
I have a problem with my cell phone, Samsung SM-G928P from Sprint.
I can not install "stock rom" or any rom with odin. :crying:
I tried to download rom stock from sammobile, but it gives me the following error "SW REV. CHECK FAIL.DEVICE: 3, BINARY: 2". I do not know what to do currently I am with "SkyHigh Kernel" & ROM Moar kernel.
I'm desperate. :crying:
Please Help!
Click to expand...
Click to collapse
use samsung smart switch to reflash it to stock
Í brick the phone
"The problem", I think is your using older firmware in Odin after you've upgraded your phones firmware. Meaning that you can't downgrade to a certain firmware anymore, try using the G928PVPS3BQB1_HOME.tar from Sam mobile. Check the version of Odin your using could need to try a newer version? I used Odin3 v3.12 in options only have auto reboot and F.Reset time checked. If you boot loop try wiping data in recovery sometimes that will cause looping and don't forget to be wiping dalvik cache, cache too.
Related
My phone is a i9505, rooted and with latest Philz recovery. I flashed [ ROM ][AROMA][4.4] KitKat KangBang v1.0.3 [Nov, 13 2013] from here http://forum.xda-developers.com/showthread.php?t=2524837.
Now i have this problem: i lost root, i can't reboot in recovery mode and my phone is now turned from the international version (9505) into TMobile US version SGH M919 so i can't downgrade or upgrade anymore.
Tried to reflash Philz by odin but nothing changed: everytime i try to enter recovery mode the phone keeps booting KitKat KangBang v1.0.3 (almost perfectly working).
What have i to do? Flash original firmware by Odin, then root and mod recovery?
Is so what kind of original firmware should be used? International 9505 or TMobile M919 one?
I'm scared to brick my device and i'd like to have it back to 9505.
Thanks in advance to anyone who helps.
c10m said:
My phone is a i9505, rooted and with latest Philz recovery. I flashed [ ROM ][AROMA][4.4] KitKat KangBang v1.0.3 [Nov, 13 2013] from here http://forum.xda-developers.com/showthread.php?t=2524837.
Now i have this problem: i lost root, i can't reboot in recovery mode and my phone is now turned from the international version (9505) into TMobile US version SGH M919 so i can't downgrade or upgrade anymore.
Tried to reflash Philz by odin but nothing changed: everytime i try to enter recovery mode the phone keeps booting KitKat KangBang v1.0.3 (almost perfectly working).
What have i to do? Flash original firmware by Odin, then root and mod recovery?
Is so what kind of original firmware should be used? International 9505 or TMobile M919 one?
I'm scared to brick my device and i'd like to have it back to 9505.
Thanks in advance to anyone who helps.
Click to expand...
Click to collapse
If you can access Download mode (Odin Mode) then you have no problems. If you're too scared to try out flashing back to original, let Kies do it for you. Install Kies and choose "Firmware Upgrade and Initialization". It will ask you for a specific Model number, You should write GT-I9505 and then it will ask you for the serial number, and then it would ask you to switch to download mode and it would download the latest stock rom for your device and flash it.
Dr.Alani said:
If you can access Download mode (Odin Mode) then you have no problems. If you're too scared to try out flashing back to original, let Kies do it for you. Install Kies and choose "Firmware Upgrade and Initialization". It will ask you for a specific Model number, You should write GT-I9505 and then it will ask you for the serial number, and then it would ask you to switch to download mode and it would download the latest stock rom for your device and flash it.
Click to expand...
Click to collapse
King regards!
This is very simple if you want it to be. Flash using the instructions at the link then do a factory wipe from stock recovery, flash again to stock and do another factory wipe.
For the flash to stock, just head over here http://forum.xda-developers.com/showthread.php?t=2267895
Follow the instructions and that will re-flash T-Mobile stock everything.
Sent from my SGH-M919 using Tapatalk
I have an SGH-1747 on AT&T. I already had the OTA 4.3 update on my phone and I wanted to simply wipe all of the apps off so it was a fresh 4.3 install as it was running slow. I went into the settings and did a factory wipe thinking that would wipe it back to original 4.3 but when it rebooted it hung on the AT&T screen.
I went into Recovery mode and wiped everything to factory refresh from there hoping that would fix it and it made it worse. Now when I reboot i simply get the Firmware upgrade encountered an issue and it asks me to use Kies to go into recovery mode. I did that multiple times and it never worked. Simply kept failing.
I am able to get into Download Mode but I can't seem to find a ODIN version of the 4.3 that I can try to flash it back to. I would love to go back to a 4.2 version if that would work but I stopped before I made it worse. In download mode it says
ODIN MODE
PRODUCT NAME SGH-I747
CUSTOM BINARY DOWNLOAD: YES (2 COUNTS) - Early on with 4.1 i had flash up to 4.2 using ODIN but i have on official AT&T release since
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: OFFICIAL
QUALCOM SECUREBOOT: ENABLE
WARRANTY BIT = 1
BOOTLOADER RP SWREV: 2
Any advice out there? I am thinking I soft bricked my phone but I am not sure?
PLEASE HELP!
There is no stock 4.3 AT&T ROM that can be flashed via Odin. You cannot downgrade the bootloader to an older version.
You can try this: http://forum.xda-developers.com/showthread.php?t=2658486
audit13 said:
There is no stock 4.3 AT&T ROM that can be flashed via Odin. You cannot downgrade the bootloader to an older version.
You can try this: http://forum.xda-developers.com/showthread.php?t=2658486
Click to expand...
Click to collapse
Thanks for the info. I actually got it fixed by giving in and going to best buy and the Samsung guys actually were able to flash it to a fresh 4.3 image. They knew it had a non factory image on it in the past based on the counter but they still did it. I'm all fixed now which was awesome.
hello, I bought this i747 in its current condition. I know nothing about its history.
when I power it on it goes to the phone, !, comp screen saying firmware upgrade encounter an issue, select recovery mode in kies.
in the top corner it says:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
QUALCOMM SECUREBOOT: ENABLE
WARRANTY BITS: 0
BOOTLOADER RP SWREV: 2
Now when I connect to kies and run emergency firmware everything loads on kies, then gives an error, and
underneath BOOTLOADER RP SWREV: 2 it says: SW REV CHECK FAIL: Fused 2 > Binary 0 in red.
If this phone fixable? Any help would be appreciated.
mtsosie said:
hello, I bought this i747 in its current condition. I know nothing about its history.
when I power it on it goes to the phone, !, comp screen saying firmware upgrade encounter an issue, select recovery mode in kies.
in the top corner it says:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
QUALCOMM SECUREBOOT: ENABLE
WARRANTY BITS: 0
BOOTLOADER RP SWREV: 2
Now when I connect to kies and run emergency firmware everything loads on kies, then gives an error, and
underneath BOOTLOADER RP SWREV: 2 it says: SW REV CHECK FAIL: Fused 2 > Binary 0 in red.
If this phone fixable? Any help would be appreciated.
Click to expand...
Click to collapse
Did you say it was recognized in Kies but firmware recovery failed? If so, and you were using Kies (not Kies 3), we may assume the last system update was not older than Android 4.1.1. I'll suggest you try these steps (in that order),i.e. if one doesn't work, try the next step ..
1. Try booting into recovery mode and doing a hard wipe/reset
2. Download the correct stock image from the thread below and flash via Odin. If you need help with flashing via Odin, please let me know
http://forum.xda-developers.com/showthread.php?t=1739426 or visit Sammobile.com to download the correct stock image.
3. Open Kies. Do not connect the phone yet. Go to Tools => Firmware Upgrade and Initialization. Enter your phone model name (SGH-I747)=>OK and serial number. Check device information inside the battery compartment. Wait for firmware download to complete and you are prompted to connect the phone and follow the rest of the on-screen instructions.
4. Contact the vendor to find out what they did wrong and see what refund options you have
Ok, so I also wasn't able to get into recovery.
I decided to flash cwm via odin. After it flashed the phone rebooted and turned on normally. I have turned it on and off like 5 times and everytime it boots normal.....But, there is still a problem... baseband version is Unknown and there is no IMEI Number.
Larry2999 said:
Did you say it was recognized in Kies but firmware recovery failed? If so, and you were using Kies (not Kies 3), we may assume the last system update was not older than Android 4.1.1. I'll suggest you try these steps (in that order),i.e. if one doesn't work, try the next step ..
1. Try booting into recovery mode and doing a hard wipe/reset
2. Download the correct stock image from the thread below and flash via Odin. If you need help with flashing via Odin, please let me know
http://forum.xda-developers.com/showthread.php?t=1739426 or visit Sammobile.com to download the correct stock image.
3. Open Kies. Do not connect the phone yet. Go to Tools => Firmware Upgrade and Initialization. Enter your phone model name (SGH-I747)=>OK and serial number. Check device information inside the battery compartment. Wait for firmware download to complete and you are prompted to connect the phone and follow the rest of the on-screen instructions.
4. Contact the vendor to find out what they did wrong and see what refund options you have
Click to expand...
Click to collapse
hi, yes those were the steps I tried and the result was fail. Now that I can boot it, it shows its 4.3 but no baseband and no imei.
mtsosie said:
hi, yes those were the steps I tried and the result was fail. Now that I can boot it, it shows its 4.3 but no baseband and no imei.
Click to expand...
Click to collapse
Oh, it's 4.3. Perhaps even better because you may be able to flash the 4.3 restore image. Your baseband/modem is corrupt or missing which is why it's showing the no baseband message.
Please see the thread below for the complete 4.3 stock restore image. Download the stock restore image and flash via custom recovery.
http://forum.xda-developers.com/showthread.php?t=2658486
Or you may just flash the 4.3 JB modem via custom recovery since you have custom recovery working. The modem zip can be found here ...
http://www.androidfilehost.com/?fid=23212708291681456
Larry2999 said:
Oh, it's 4.3. Perhaps even better because you may be able to flash the 4.3 restore image. Your baseband/modem is corrupt or missing which is why it's showing the no baseband message.
Please see the thread below for the complete 4.3 stock restore image. Download the stock restore image and flash via custom recovery.
http://forum.xda-developers.com/showthread.php?t=2658486
Or you may just flash the 4.3 JB modem via custom recovery since you have custom recovery working. The modem zip can be found here ...
http://www.androidfilehost.com/?fid=23212708291681456
Click to expand...
Click to collapse
:good: right on. you rock man. I flashed the modem and it works great now. thanks again.
mtsosie said:
:good: right on. you rock man. I flashed the modem and it works great now. thanks again.
Click to expand...
Click to collapse
You are most welcome. Glad to know it's now working.
hey guys am in trouble
Odin Refuse to flash
I747 warranty bit :1
bootloader rp swrev 2
SW rev check fail fused 2
Phone stuck on kies firmware upgrade encounterd
I Cant get 4.3 back again or downgrade to any older version
plz help me :'(
here is two screen shot in download mode while odin error
and in normal mode when i try 2 open
dark_darkness said:
hey guys am in trouble
Odin Refuse to flash
I747 warranty bit :1
bootloader rp swrev 2
SW rev check fail fused 2
Phone stuck on kies firmware upgrade encounterd
I Cant get 4.3 back again or downgrade to any older version
plz help me :'(
here is two screen shot in download mode while odin error
and in normal mode when i try 2 open
Click to expand...
Click to collapse
Can you try flashing custom recovery via Odin and then using custom recovery to do a stock restore to 4.3 following the instructions in the following thread ...
http://forum.xda-developers.com/showthread.php?t=2658486
can u share a link?
Larry2999 said:
Can you try flashing custom recovery via Odin and then using custom recovery to do a stock restore to 4.3 following the instructions in the following thread ...
http://forum.xda-developers.com/showthread.php?t=2658486
Click to expand...
Click to collapse
i've tried many custom roms
start flashing will and end with bug error at the end coz of warranty
can u share me a link for firmware tested ?
dark_darkness said:
i've tried many custom roms
start flashing will and end with bug error at the end coz of warranty
can u share me a link for firmware tested ?
Click to expand...
Click to collapse
I suggested custom recovery and not custom ROM. The idea is to get your phone back in working order first. Flashing a complete stock restore image should do it. Please refer to the thread I forwarded earlier. You should be able to flash custom recovery (like CWM or TWRP) to your phone via Odin and then use the custom recovery to flash the stock restore image.
hey i have a note 2 running stock firmware v4.1.1 ... i tried to update the phone to 4.1.2 by the phone and not kies and when the download of the upgrade finishes , the phone says upgrade fails and keeps me on 4.1.1 ...............
so i went into a different direction to root my phone and then flash a custom rom.... i rooted it successfully and flashed MJ5 bootloader also and was ready to install the custom rom running 4.3... i went into recovery and was flashing the rom .... when i choose the flashing method and finished everything and did reboot ... the phone got me a message says that “Firmware upgrade encountered an issue" and i need kies recovery
Please help me out with this and give me the correct way to fix this.
NB: My phone is international Note II [N7100]
aboalghool said:
hey i have a note 2 running stock firmware v4.1.1 ... i tried to update the phone to 4.1.2 by the phone and not kies and when the download of the upgrade finishes , the phone says upgrade fails and keeps me on 4.1.1 ...............
so i went into a different direction to root my phone and then flash a custom rom.... i rooted it successfully and flashed MJ5 bootloader also and was ready to install the custom rom running 4.3... i went into recovery and was flashing the rom .... when i choose the flashing method and finished everything and did reboot ... the phone got me a message says that “Firmware upgrade encountered an issue" and i need kies recovery
Please help me out with this and give me the correct way to fix this.
NB: My phone is international Note II [N7100]
Click to expand...
Click to collapse
Install latest philz cwm or twrp recovery, go into recovery and wipe data/factory reset or choose option to clean for new rom Install, after that flash custom rom.
Ok this is my problem, I was on a custom rom because kikat was not released for my device. when it was I used odin and flashed the stock jelly bean rom I had. it worked and I went into settings and clicked update. when I came back to my tablet it had stock kikat 4.4.2. I went into download mode to add twrp and root. in download mode there was a new string of text after I flash twrp:
ODIN mode
product name:sm-t310_NA
current binary:
system status:
AP SEREV: A1
the "AP SEREV: A1" was new, For some reason twrp worked but i could not get root access so in twrp I restored a backup of my custom rom. so I gave it another try but when I tried to flash jelly bean, it gave me an error(FAILED) in oden and gave me a "invalid magic string" error in download mode.
What should i do, I am stuck on a custom rom I dont want. if it is a matter of flashing kikat in odin, then please direct me to the American SM-T310 kikat STOCK ROM file
thanks
ps if there is some new way of getting root in kikat that would also help.
androidhacker007 said:
Ok this is my problem, I was on a custom rom because kikat was not released for my device. when it was I used odin and flashed the stock jelly bean rom I had. it worked and I went into settings and clicked update. when I came back to my tablet it had stock kikat 4.4.2. I went into download mode to add twrp and root. in download mode there was a new string of text after I flash twrp:
ODIN mode
product name:sm-t310_NA
current binary:
system status:
AP SEREV: A1
the "AP SEREV: A1" was new, For some reason twrp worked but i could not get root access so in twrp I restored a backup of my custom rom. so I gave it another try but when I tried to flash jelly bean, it gave me an error(FAILED) in oden and gave me a "invalid magic string" error in download mode.
What should i do, I am stuck on a custom rom I dont want. if it is a matter of flashing kikat in odin, then please direct me to the American SM-T310 kikat STOCK ROM file
thanks
ps if there is some new way of getting root in kikat that would also help.
Click to expand...
Click to collapse
Try towel root http://forum.xda-developers.com/showthread.php?t=2784152
androidhacker007 said:
Ok this is my problem, I was on a custom rom because kikat was not released for my device. when it was I used odin and flashed the stock jelly bean rom I had. it worked and I went into settings and clicked update. when I came back to my tablet it had stock kikat 4.4.2. I went into download mode to add twrp and root. in download mode there was a new string of text after I flash twrp:
ODIN mode
product name:sm-t310_NA
current binary:
system status:
AP SEREV: A1
the "AP SEREV: A1" was new, For some reason twrp worked but i could not get root access so in twrp I restored a backup of my custom rom. so I gave it another try but when I tried to flash jelly bean, it gave me an error(FAILED) in oden and gave me a "invalid magic string" error in download mode.
What should i do, I am stuck on a custom rom I dont want. if it is a matter of flashing kikat in odin, then please direct me to the American SM-T310 kikat STOCK ROM file
thanks
ps if there is some new way of getting root in kikat that would also help.
Click to expand...
Click to collapse
This thread DOESNT belong here!!!
This thread must be moved on q&a
Srry can u move it plz
Sent from my SM-T310 using XDA Premium 4 mobile app
androidhacker007 said:
Srry can u move it plz
Sent from my SM-T310 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
If you are still looking for a 4.4.2 stock rom, try SamMobile.com. I used this one:
SM-T310 Canada 2014 July 4.4.2 T310XXUBNE9 T310XACBNE8
After that, I used this guide to root:
http://www.droidviews.com/root-galaxy-tab-3-8-0-sm-t310-on-kitkat/
and this for getting TWRP:
http://forum.xda-developers.com/showthread.php?t=2619518
Never, ever do an OTA update. You never know what sort of turd you are going to get. See the Knox fiasco, or my iPad 2 that is going to be a rifle target after a retard I loaned it to updated to 7-whatever.
Two things to try.
The Toolkit and this ROM.
If you already have a recovery on your Tab, this should be simple. Download one of the rooted versions of the ROM, get it on to your tablet (SD card preferred), wipe and install.
If all else fails, try GalaTab3. It WILL work, unless your mo-sheen is broken.
ETA: Whoa, does the stock Samsung 4.4.x ROM have Knox as well?