Hi and sorry my bad english ( im spanish)
My Sony smartwatch dont power on after i wash my hands (the watch was properly closed) and i cant power the watch on.
I have tried to restore it with sony pc companion but the program doesnt recognises the watch. My computer recognises the watch as an unknown device. I cant use flash tools because i dont enable that option on the watch. So what i could do 8 i dont have warranty anymore):crying:
Related
Hi People.
My HOX was fell from the car while i was driving...so it fall really hard against the concrete floor.... i stop the car to getting my HOX back and assuming its gonna be broken or something ...but instead it was almost intact ...no broken glass or screen... it only was dirty and just a few scratches ( i use a gel silicone case ...really works)... well now i was able to turn it up and see the real damage . after a few tries it didnt do nothing, just vibrates like when you turn it on , but the screen was black...after more tries... the miracle come true the screen turn on and i was very happy...i unlocked the phone and the screen freeze out ... i restart my hox by pressing power button about ten seconds and after that... the screen stays blank ( black , dead) for ever an ever , but all the other things like the three buttons lights works and the red/green led notification works ...but i was devastated.
The other part of the story is that i was trying to restore all he important file... but the usb option was on "only charge" so wasnt able to get into the folder like windows...after that i think in a way to control the phone with sdk adb an other things... and i try two softwares, moborobo and android screencast.. i was surprised when i connect my HOX to my pc ...and open the software (screencast or moborobo) and again i see the light at the end of the tunnel... i saw my lockscreen in this virtual android controller software , then i slide my finger to unlock my phone ...and surprise ...it still work....as i saw it in this virtual controller on my pc the touch screen works great ...the only thing it doesnt work in my HOX is the screen , and its not broken...
ANY IDEA??? SOFTWARE?...HARDWARE?...SCREEN CRACKED? SCREEN DISCONNECTED?
is there an apk who can check hardware or software and tell you whats wrong on your phone...like a scanner??
the technical services here doest exists for this model yet.... cause the HOX is almost new and not too popular ..
thanks...
sorry about my english.
cheers from Chile
hi everyone. I just bought sony smartwatch 2 yesterday, and i faced some problems. i've seen and tried all of your tips. and still not pairing with my Eklasse XM590. the problem is: before i install smart connect mobile and smartwatch paird regular. but after installing. the pairing connection remains just one second and unpaired. Do anyone please have a solution>
please respond and thanks in advance
hint: i tried pairing in both root and unroot . it's the same
is there any body who can help?
Have you installed the 2 app : smartconnect and smartwatch2 app ?
after enable search BT device in phone BT setting and made phone discoverable.
If SW2 not new or yet paired with a phone I think you must press power button and keep pressed more than 15s to enter on new pairing mode (after SW2 has Power OFF of course).
(If SW2 is yet in phone BT device click to unpair to remove before, and you can restart with new conddition)
dersie said:
Have you installed the 2 app : smartconnect and smartwatch2 app ?
after enable search BT device in phone BT setting and made phone discoverable.
If SW2 not new or yet paired with a phone I think you must press power button and keep pressed more than 15s to enter on new pairing mode (after SW2 has Power OFF of course).
(If SW2 is yet in phone BT device click to unpair to remove before, and you can restart with new conddition)
Click to expand...
Click to collapse
I did tthese steps before and same thing. Once i press unpair SW2 doesnt connect.
The connection remains untill i install smart connect. SW wont pair again :/
Mr.9lj9lj said:
I did tthese steps before and same thing. Once i press unpair SW2 doesnt connect.
The connection remains untill i install smart connect. SW wont pair again :/
Click to expand...
Click to collapse
Smart Connect ( and smartwatch2 eventually) must be installed before.
And have you forced the SW2 re-pairing by resetting the pairing with the power button more than 15s until the SW2 display the search phone icon (not the connect icon with the "X" to abort) ?
dersie said:
Smart Connect ( and smartwatch2 eventually) must be installed before.
And have you forced the SW2 re-pairing by resetting the pairing with the power button more than 15s until the SW2 display the search phone icon (not the connect icon with the "X" to abort) ?
Click to expand...
Click to collapse
That's what i did
I installed both, smart connect & sw 2, before pairing and the problem still here. Once it paired, it disconnects.
But when i tried to pair before installing them, the pairing bond continues!
Ialso tried to reset sw2, search for device appears and the same thing happens again.
Thanks so much for your concerns
What about wiping dalvick cache? Can it be useful?
I have the same issue, except my smart connect app force closes every disconnect
sorry but can u fixed that,i got the same problems..
try the second steps from my post here
Hello, I just bought sw2 and pair with phone (all ok) then update to newest version sw2 (without ask).
So, watch wont go to home screen. When I press home screen button or double power button, ws2 just vibrate, go black, disconect from phone and then again show clock and connect with phone.
Make some video https://youtu.be/OvINnCyDd-U
I try this http://forum.xda-developers.com/smartwatch-2/help/solution-bricked-sw2-t3172226
But when pair with phone sw2 download update and still the same.
Maybe someone have any ideas what more I can do?
Sorry for bad english :/
Seem faulty watch when I see the screen going blank after press button
I think the same. Sad... Thank you
Well a few days ago, like 2 weeks ago, I thougt I lost my SW3 (I use it w / o leash because it broke and there's no replacement for the stainless steel one) but actually it was lost on my travel bag xD
After plug in again it started to charge, but when I tried to turn on (after reach 100%), after the sony and SW3 logo, it turns off, like it has a problem at boot. I tried to repair via Xperia Companion and the process was succesful, but the watch just gets stuck on the same SW3 logo.
Now I think is the battery, but I'm really hoping is not, there are any suggestion guys about what could be happening?
Is it stuck at the 4 dots spinning? If So I have the same problem, I have tried a factory reset, updating the rom via push commands etc I have brought a new SWR50 thats working with ADB debugging enabled this time (Didn't do it on the last one) my question hopefully will help the OP as well can I take a complete clone/rom backup from the working watch then push that to the broken watch (Bare in mind no debugging enabled on the broken one) Also to the OP have you held down the power button to get to the fastboot menu and factory reset/recovery settings? if not then you turn off the watch, press and hold the power button until the "insert usb now" shows, you then press the power button quickly twice to access the recovery menus
The Watergod said:
Is it stuck at the 4 dots spinning? If So I have the same problem, I have tried a factory reset, updating the rom via push commands etc I have brought a new SWR50 thats working with ADB debugging enabled this time (Didn't do it on the last one) my question hopefully will help the OP as well can I take a complete clone/rom backup from the working watch then push that to the broken watch (Bare in mind no debugging enabled on the broken one) Also to the OP have you held down the power button to get to the fastboot menu and factory reset/recovery settings? if not then you turn off the watch, press and hold the power button until the "insert usb now" shows, you then press the power button quickly twice to access the recovery menus
Click to expand...
Click to collapse
I forgot about this thread lol
thanks dude!, A couple times it reached the spinning dots, but not always, sometimes it turned off on the SW3 logo before the dots appear, and actually I tried all those things you mentioned, but it didn't work, also I think my watch is (even more) screwed now xD...
Trying to do a second repair on Xperia Companion, the watch got turned off in mid repair, lending obviously on an error, and also losing the ability of do offline charge so once the battery reach 0, is over...
now when I plug in just stays on the SW3 logo, I still can go to connect USB screen and go to the two clicks menu (and stays on), but every time I try a repair, in the middle of the process disconnects and turns off, I don't know exactly why only when is plugged on the repair process it turns off, even pluged in the PC w/o repair stays connected all the time... bad thing is I don't know if is charging or not, so could stop working anytime
Have you tried to push the update through adb recovery mode?
The Watergod said:
Have you tried to push the update through adb recovery mode?
Click to expand...
Click to collapse
every day I'm more convinced the watch is screwed
If I turn on the watch stays on the SW3 logo all the time (it seems offline charge works after all), I even can go to the "insert USB" screen and stays on all the time, but when I try to push something to the watch, always disconnects, turns off and the process obvioulsy gets interrumpted, I'm losing my hopes xD
I'm using the original charging wire, but tried with other working ones
my sister bought me this smart watch , it came on long enough to program a few this after I charge it and then 10 minutes later it shut off and now it won't come back on or power up , what should I do ?
I have a weird problem with my sw3. When I plugin my watch to a charger nothing shows up but the watch gets heated up. But when I connect it to PC it just keeps turning on and off. Tried various methods available on this site but none of them worked.
Hi,
I have a stock standard one plus3. Screen is broken. However phone seems to boot up. I have red light for charging. Capacitive buttons work as well as if i click them i feel vibration as feedback.
At this stage i don't care about the phone is there a software/hardware way to get the data out of the internal memory. I am happy to disassemble and get the chip out but what follows is elluding me.
Debugging is disabled afaik. Tried booting into recovery mode and it does vibrate when i hold power and volume down but nothing happens after that.
Any ideas ?
Regards,
atk
I have previously been through this situation before.
If you have Google Photos backing up your photos, you can just vaguely touch the screen while taking screenshots along the way, since you would able to access them on Google Photos' webpage, till you reach to the Developer Options, and eventually enabling Android Debugging. And after all of that, you would be able to download some tool—like Vysor—on your computer to control your Android device.
Please note that if the screen's touch capability is also broken, use a wired game controller, keyboard, or mouse to connect a Bluetooth-based one, since you will need your phone connected to the computer to enable Android Debugging.
the phone worth saving, just get a cheap replacement screen. you won't be able to recover anything without unlocking the phone first.
also check your google account, it can store your stuff up to 15GB if your sync was turned on.