Develop Bugs

HELP. Maybe bricked phone?

Well I was on the 4/10 nightly for CM 10.1, and I wanted to switch back to a stock TW ROM, so I downloaded and flashed PlainJane. Upon reboot my phone demanded that I reset my data because encryption had failed, and I never had my device encrypted, but the only thing I could do was press reset. So I did, and the phone booted into TWRP and flashed a quick message and rebooted to the same screen. I thought oh well no biggie I can restore my backup...NOPE. Looks like my SD card decided to corrupt. Well hey theres Odin right? WRONG AGAIN. I tried the method at
http://www.sxtpdevelopers.com/showthread.php?t=74 and Odin tells me
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> cache.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006> param.bin
<ID:0/006> recovery.img
<ID:0/006> sboot.bin
<ID:0/006>
<ID:0/006>
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I cannot boot into recovery because it tells me a firmware update has failed. Please someone help...

When you use ljc it will always fail at sbin it's not going to install the old boot loader use the new tar from This thread
http://forum.xda-developers.com/showthread.php?t=2086769
Sent from my SPH-L900 using Xparent BlueTapatalk 2

Epix4G said:
When you use ljc it will always fail at sbin it's not going to install the old boot loader use the new tar from This thread
http://forum.xda-developers.com/showthread.php?t=2086769
Sent from my SPH-L900 using Xparent BlueTapatalk 2
Click to expand...
Click to collapse
THANK YOU SO MUCH! I got TWRP up and running and I'm flashing the stock reset now .

Odin wont install stock rom

I tried rooting my Galaxy sIII and it failed, and wont boot.
So per recomendations I found here, I downloaded a stock image for the phone, and every one I try to flash, ends in an error in odin.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCALEM_I747ATTALEM_I747UCALEM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
And on the phone it reads:
SW REV CHECK FAIL : FUSED 2 > BINARY 0
HELP!

Bump!
Can anyone help?

BlakDrgn said:
Bump!
Can anyone help?
Click to expand...
Click to collapse
What is your firmware on phone? Did you take last OTA to 4.3?

norbarb said:
What is your firmware on phone? Did you take last OTA to 4.3?
Click to expand...
Click to collapse
Yeah it ota'ed to 4.3 I believe.

BlakDrgn said:
Yeah it ota'ed to 4.3 I believe.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2537910 Read this and some more about 4.3 OTA
http://forum.xda-developers.com/showthread.php?t=2526698

norbarb said:
http://forum.xda-developers.com/showthread.php?t=2537910 Read this and some more about 4.3 OTA
http://forum.xda-developers.com/showthread.php?t=2526698
Click to expand...
Click to collapse
Thanks! reflashed Clockwork mod and the phone booted right up!

Bricked when rolling back from 4.3 to 4.1.2
I got the OTA update 4.3 and it has been draining the battern significantly. So i resorted to revert to 4.1.2 and i think bricked the phone.
This is the error i get from odin when trying to flash 4.1.2
<OSM> I747UCALG1_I747ATTALG1_I747UCALG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response from boot-loader
<ID:0/006> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
I see this error in the phone
s3 sw rev check fail: Fused 2 > Binary 0
Now phone does not boot up either. I'm not a android geek - was just trying to get to a older stable version where battery easily lasted for a day...
Saw this thread after i tried to flash 4.1.2 I still don't see a solution posted on how to get the phone to work again...
Please help!!!!!!!!!!!!!!!!!
---------- Post added at 06:41 AM ---------- Previous post was at 06:35 AM ----------
BlakDrgn said:
Thanks! reflashed Clockwork mod and the phone booted right up!
Click to expand...
Click to collapse
Can you please help on how to get this clockwork mod reflashed?

error when flashing ROM via Odin

hi, i'm trying flash a ROM to note 10.1 p605, it has Singapore ROM originally and im trying to flash German ROM
i get this error in Odin every time i try to flash:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P605XXUAMJ2_P605OJVAMI3_P605XXUAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)

Mashari_F said:
hi, i'm trying flash a ROM to note 10.1 p605, it has Singapore ROM originally and im trying to flash German ROM
i get this error in Odin every time i try to flash:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P605XXUAMJ2_P605OJVAMI3_P605XXUAMJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
1) Have you tried to use an other usb port?
2) do you use the original usb cable?
3) do you have all the samsung drivers installed?
4) make eure that samsung kies is not running in the background
Hope it helps you
Gesendet von meinem SM-P600 mit Tapatalk

Got the same problem, so recovered it from kies
Skickat från min SM-P605 via Tapatalk

Hi... Anybody have a solution for this problem? Have the tablet returned from a service and tried to flash the recovery but it just doesn't work.
THanks a lot for any help.

ronaldphl said:
Hi... Anybody have a solution for this problem? Have the tablet returned from a service and tried to flash the recovery but it just doesn't work.
THanks a lot for any help.
Click to expand...
Click to collapse
Is it giving you a FAIL after flashing , or doesn`t show up after a successful flash.
If it doesn`t show up after flashing , re-flash but untick "Auto-Reboot" within odin before flashing & restart manually after flashing.

I have a "Fail after flashing" - complete (Write) - operation failed in Odin

Which odin
Hi,
When flashing with oder it depends on the package which oder will work.
At my p 605 the 1.86 version was working without probs.
The best is to use the Oden which is coming together the Roms Zipfile.
I hope this info helps please let me know.
Good luck

FSkyman said:
Hi,
When flashing with oder it depends on the package which oder will work.
At my p 605 the 1.86 version was working without probs.
The best is to use the Oden which is coming together the Roms Zipfile.
I hope this info helps please let me know.
Good luck
Click to expand...
Click to collapse
I tried all the possible combination... different Odin... different cables and ports... it just didn't work.
Since I read from a old post that flashing a original rom thru Odin helps... and i tried... Odin works and the rom can be flashed without prompting the signature verification failed error.
I suspect if Samsung has done something to make the recovery image fails...
I tried flashing the recovery using the stock recovery too and it failed as well

Recovery Flashing
ronaldphl said:
I tried all the possible combination... different Odin... different cables and ports... it just didn't work.
Since I read from a old post that flashing a original rom thru Odin helps... and i tried... Odin works and the rom can be flashed without prompting the signature verification failed error.
I suspect if Samsung has done something to make the recovery image fails...
I tried flashing the recovery using the stock recovery too and it failed as well
Click to expand...
Click to collapse
Now I am confused are you talking about recovery or rom ?
The only recovery I could get to work was the TWRP - this Zip file comes with a Odin that works.
Cwm philz are not working.
But keep in mind as soon you installed twrp your knox counter is tripped.
For rom flashing you have to wipe your tablet and then follow these instructions xxxx://www.droidgator.com/update-galaxy-note-101-sm-p605-android-43-xxubmj9-firmware/.
Before starting backup your tab then everything should be fine.

Thanks for your effort in helping me out...
Before I sent my tablet for servicing... I restored the tablet with Kies to the original factory setting and rom as I HAD rooted my P605 and flashed a custom rom before. [Although the Know count is 0*1 anyway.... but the service centre was kind enough to fix my tablet as it's a hardware failure instead of anything to do with the ROM ]
When I got my tablet back and tried to flash the TWRP into it, this problem surfaced. And I read from another post that some say flashing a Samsung original rom could help I tried but to no avail. Still I am waiting and looking for a solution.
I tried Odin 3.04 3.07 and 1.85 with the two versions of TWRP but still none of them work.

Cant flash Stock firmmware
Hi Guys
Tried all methods in the fourms but i am still not able to flash stock firmware from odin.
this is the error i get.
I am trying to update using Odin 3.09 as well as 3.07. but it is failing while writing system.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img.ext4
<ID:0/004> NAND Write Start!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can someone please help me? Is this because this shows Write Protection : Enable?

nihalvm said:
Hi Guys
Tried all methods in the fourms but i am still not able to flash stock firmware from odin.
this is the error i get.
I am trying to update using Odin 3.09 as well as 3.07. but it is failing while writing system.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img.ext4
<ID:0/004> NAND Write Start!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can someone please help me? Is this because this shows Write Protection : Enable?
Click to expand...
Click to collapse
---
Might you recall what the firmware version was before you started to flash this one?
I am also trying to recover from NC3 back to MJ4XAC and it is not allowing me to finish, Kies also does not recover the tablet. It looks like one of the filesystems is in a different state. With TWRP there are options to perform CHMOD on the file systems but I figure I have been mocking around long enough and for some reason beyond my experience the system is not responding.
Can you still get into ADB mode? That might be an option to see if you can gain access?

nihalvm said:
Hi Guys
Tried all methods in the fourms but i am still not able to flash stock firmware from odin.
this is the error i get.
I am trying to update using Odin 3.09 as well as 3.07. but it is failing while writing system.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img.ext4
<ID:0/004> NAND Write Start!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can someone please help me? Is this because this shows Write Protection : Enable?
Click to expand...
Click to collapse
Is the sm-p605v (verizon) synonymous with sm-p605 for technical purposes? I am having identical problems with lt03ltevzw. Odin 3

aelaan said:
---
Might you recall what the firmware version was before you started to flash this one?
I am also trying to recover from NC3 back to MJ4XAC and it is not allowing me to finish, Kies also does not recover the tablet. It looks like one of the filesystems is in a different state. With TWRP there are options to perform CHMOD on the file systems but I figure I have been mocking around long enough and for some reason beyond my experience the system is not responding.
Can you still get into ADB mode? That might be an option to see if you can gain access?
Click to expand...
Click to collapse
Although it failed, I was able to recover using kies and use tablet as normal without data loss. It might be because at that point I had not rooted my tab and system state was still original in odin.
By the way I was on MJ4 xsa(AUSTRALIA) trying to install NC2 TGY(HONG KONG).
Now I have rooted it and have I installed NC2. I am still not sure what the issue was. But the only thing I did different was, first was using a virtual machine, but now did in an actual windows machine.
Can you please try this? If you can, install back NC2 using odin. Boot it once, then try recovering using kies. Kies recover mode gets your latest firmware based on your serial number. Not what firmware you are running.
Please post back the result. Interested to know the outcome.
Sent from my SM-P605 using XDA Premium 4 mobile app
---------- Post added at 08:38 AM ---------- Previous post was at 08:33 AM ----------
Khazaad said:
Is the sm-p605v (verizon) synonymous with sm-p605 for technical purposes? I am having identical problems with lt03ltevzw. Odin 3
Click to expand...
Click to collapse
I don't think it is. Although the specs are the same, read somewhere that the internal partition structure for carrier branded firmware are different to generic. Don't remember where I read that. But can't confirm that either.
Sent from my SM-P605 using XDA Premium 4 mobile app

Verizon Note 4 Will not flash in Odin

Alright i did a major mess up on my phone , Alright so i was rooted and was on CM13 well i decided to go back to stock rom so i downloaded the lastest Firmware and use odin to flash it and while it was flashing it failed . So i pulled the battery and restarted the phone and now i am hit with the ( Your device didn't update succesfully. Use the Verizon Software repair assistant to repair your deivce ) So i did that and it fails at 84% So i tryed reflashing again via odin and i keep getting failed well when i tryed flashing CF-Auto root to just see if it did anything it failed but when i booted the phone up it went stright to the samsung logo and boot looped so i was ok so i went into recovery and tryed to wipe /factory reset but keep getting a error .
So my thing is idk what to do i have tryed flashing via odin and it keeps failing i get this
Code:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1203)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> tz.mbn
<ID:0/007> __XmitData_Write
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/007> Added!!
and that is the lastest firmware from sam mobile
if anyone can help me i really appericate it

pfcland said:
Alright i did a major mess up on my phone , Alright so i was rooted and was on CM13 well i decided to go back to stock rom so i downloaded the lastest Firmware and use odin to flash it and while it was flashing it failed . So i pulled the battery and restarted the phone and now i am hit with the ( Your device didn't update succesfully. Use the Verizon Software repair assistant to repair your deivce ) So i did that and it fails at 84% So i tryed reflashing again via odin and i keep getting failed well when i tryed flashing CF-Auto root to just see if it did anything it failed but when i booted the phone up it went stright to the samsung logo and boot looped so i was ok so i went into recovery and tryed to wipe /factory reset but keep getting a error .
So my thing is idk what to do i have tryed flashing via odin and it keeps failing i get this
Code:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1203)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> tz.mbn
<ID:0/007> __XmitData_Write
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/007> Added!!
and that is the lastest firmware from sam mobile
if anyone can help me i really appericate it
Click to expand...
Click to collapse
I don't know if you tried already, but perhaps you could simultaneously flash a PIT file (hsbadr has a post over this) and a stock firmware image in ODIN. This should fix any borked partitions, if there are any. If this doesn't work, then I'm afraid I can't help you further. You'd have to wait on someone more knowledgeable than me. Or, you can take it into a verizon store or best-buy and ask for help there?

SirLaughsalot said:
I don't know if you tried already, but perhaps you could simultaneously flash a PIT file (hsbadr has a post over this) and a stock firmware image in ODIN. This should fix any borked partitions, if there are any. If this doesn't work, then I'm afraid I can't help you further. You'd have to wait on someone more knowledgeable than me. Or, you can take it into a verizon store or best-buy and ask for help there?
Click to expand...
Click to collapse
Were can i find this post at

ok first make sure you are using this odin https://www.androidfilehost.com/?fid=312968872162493207
Make sure you use this pit https://www.androidfilehost.com/?fid=95784891001613364
Then make sure you are using this tar https://www.androidfilehost.com/?fid=24411628330026105
Extract odin and put it any where then extract the tar from the zip and go to the odin I uploaded in the left theirs a tab labeled pit click that and click pit in that tab select the pit i gave you than go to AP and and go to where you extracted that tar and select it wait for it to check MD5 it may stop responding just wait than click start and wait for it to flash than you should be on stock unrooted lollipop

Bren123 said:
ok first make sure you are using this odin https://www.androidfilehost.com/?fid=312968872162493207
Make sure you use this pit https://www.androidfilehost.com/?fid=95784891001613364
Then make sure you are using this tar https://www.androidfilehost.com/?fid=24411628330026105
Extract odin and put it any where then extract the tar from the zip and go to the odin I uploaded in the left theirs a tab labeled pit click that and click pit in that tab select the pit i gave you than go to AP and and go to where you extracted that tar and select it wait for it to check MD5 it may stop responding just wait than click start and wait for it to flash than you should be on stock unrooted lollipop
Click to expand...
Click to collapse
Alright that actually worked it flashed and did not fail , Thanks alot your a life saver now my second question is When i boot the Phone Up and it shows the picture Samsung Galaxy Note 4 Andriod how do i get the Custom part on it to go off with the lock ?

pfcland said:
Alright that actually worked it flashed and did not fail , Thanks alot your a life saver now my second question is When i boot the Phone Up and it shows the picture Samsung Galaxy Note 4 Andriod how do i get the Custom part on it to go off with the lock ?
Click to expand...
Click to collapse
Is this on first boot go through set up and when your on the home screen power off the phone then power it on and if you were on cm 13 and flashed it with TWRP you tripped Knox so if powering off doesn't work then you can't get rid of it without rooting

Bren123 said:
Is this on first boot go through set up and when your on the home screen power off the phone then power it on and if you were on cm 13 and flashed it with TWRP you tripped Knox so if powering off doesn't work then you can't get rid of it without rooting
Click to expand...
Click to collapse
Yea it shows it on first boot shows a lock that is unlocked

pfcland said:
Yea it shows it on first boot shows a lock that is unlocked
Click to expand...
Click to collapse
OK complete setup when it gets off verizon screen then power it off and power it back on
Sent from my SM-N910V using Tapatalk

Bren123 said:
OK complete setup when it gets off verizon screen then power it off and power it back on
Sent from my SM-N910V using Tapatalk
Click to expand...
Click to collapse
Ok it is gone thanks alot man

Download this app called Samsung phone info from Google play and look at Knox warranty void if it shows up with 0x1 your warranty is voided I'm not sure if there is a way to reset it back to 0x0.

Bren123 said:
Download this app called Samsung phone info from Google play and look at Knox warranty void if it shows up with 0x1 your warranty is voided I'm not sure if there is a way to reset it back to 0x0.
Click to expand...
Click to collapse
it shows Ox1 but i am not worried about it because my phone is paid off

pfcland said:
it shows Ox1 but i am not worried about it because my phone is paid off
Click to expand...
Click to collapse
Oh OK cool.
Sent from my SM-N910V using Tapatalk
---------- Post added at 04:38 AM ---------- Previous post was at 04:37 AM ----------
pfcland said:
Ok it is gone thanks alot man
Click to expand...
Click to collapse
Your Welcome. [emoji3]
Sent from my SM-N910V using Tapatalk

pfcland said:
Alright that actually worked it flashed and did not fail , Thanks alot your a life saver now my second question is When i boot the Phone Up and it shows the picture Samsung Galaxy Note 4 Andriod how do i get the Custom part on it to go off with the lock ?
Click to expand...
Click to collapse
I'm at the exact point as he was but I haven't been able to try verizon software update assistant yet. However, I'm not able to install the PIT and TAR he used. Here's what I get. Any ideas? Under options I have the first three checked (auto reboot, re partition, f reset time).
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
EDIT 1: Unchecked auto reboot and switched COM PORTS and it worked! THANK YOU!!!

droiddude414 said:
I'm at the exact point as he was but I haven't been able to try verizon software update assistant yet. However, I'm not able to install the PIT and TAR he used. Here's what I get. Any ideas? Under options I have the first three checked (auto reboot, re partition, f reset time).
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
EDIT 1: Unchecked auto reboot and switched COM PORTS and it worked! THANK YOU!!!
Click to expand...
Click to collapse
Do this
Bren123 said:
ok first make sure you are using this odin https://www.androidfilehost.com/?fid=312968872162493207
Make sure you use this pit https://www.androidfilehost.com/?fid=95784891001613364
Then make sure you are using this tar https://www.androidfilehost.com/?fid=24411628330026105
Extract odin and put it any where then extract the tar from the zip and go to the odin I uploaded in the left theirs a tab labeled pit click that and click pit in that tab select the pit i gave you than go to AP and and go to where you extracted that tar and select it wait for it to check MD5 it may stop responding just wait than click start and wait for it to flash than you should be on stock unrooted lollipop
Click to expand...
Click to collapse
1. Extract odin into a desktop folder
2. Extract the tar from the zip and place it in the odin folder .
3. Place the PIT file inside the odin folder
4. Open odin folder
5. Run odin
6. In the left you should see some menues click on the one that says PIT
7. Now browse for thr PIT file and select it
8. Now Click on the AP button and select the TAR file in the odin folder .
9. Wait for it to load
10. Now make sure the re partition is not check marked .
11. Now click start and it should flash succesfully.
It will reboot and show the lock screen but one you reboot again it should be gone
Hope this helps

Bren123 said:
ok first make sure you are using this odin https://www.androidfilehost.com/?fid=312968872162493207
Make sure you use this pit https://www.androidfilehost.com/?fid=95784891001613364
Then make sure you are using this tar https://www.androidfilehost.com/?fid=24411628330026105
Extract odin and put it any where then extract the tar from the zip and go to the odin I uploaded in the left theirs a tab labeled pit click that and click pit in that tab select the pit i gave you than go to AP and and go to where you extracted that tar and select it wait for it to check MD5 it may stop responding just wait than click start and wait for it to flash than you should be on stock unrooted lollipop
Click to expand...
Click to collapse
Bren123 (or anyone who can help), I am having a same type of problem flashing in Odin. I would like to put my phone back to kitkat, back when it was smooth and fast. When I have tried to flash with Odin it failed everytime, however it was an older version of Odin v3.10.7. I have a stock kitkat rom from Sam mobile. Can I load it with the newer Odin and the Pit file you shared links for? Any help would be appreciated!

Bren123 said:
ok first make sure you are using this odin https://www.androidfilehost.com/?fid=312968872162493207
Make sure you use this pit https://www.androidfilehost.com/?fid=95784891001613364
Then make sure you are using this tar https://www.androidfilehost.com/?fid=24411628330026105
Extract odin and put it any where then extract the tar from the zip and go to the odin I uploaded in the left theirs a tab labeled pit click that and click pit in that tab select the pit i gave you than go to AP and and go to where you extracted that tar and select it wait for it to check MD5 it may stop responding just wait than click start and wait for it to flash than you should be on stock unrooted lollipop
Click to expand...
Click to collapse
lugnuttz said:
Bren123 (or anyone who can help), I am having a same type of problem flashing in Odin. I would like to put my phone back to kitkat, back when it was smooth and fast. When I have tried to flash with Odin it failed everytime, however it was an older version of Odin v3.10.7. I have a stock kitkat rom from Sam mobile. Can I load it with the newer Odin and the Pit file you shared links for? Any help would be appreciated!
Click to expand...
Click to collapse
I tried again with the never version of odin and it still does not work for me. This is what I get:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can anyone please help me get my phone back to kitkat???
I can only flash marshmallow, or now lollipop v5.11, after following the instructions above. I still can't get the kitkat firmware to work.
Please help!

Bren123 said:
ok first make sure you are using this odin https://www.androidfilehost.com/?fid=312968872162493207
Make sure you use this pit https://www.androidfilehost.com/?fid=95784891001613364
Then make sure you are using this tar https://www.androidfilehost.com/?fid=24411628330026105
Extract odin and put it any where then extract the tar from the zip and go to the odin I uploaded in the left theirs a tab labeled pit click that and click pit in that tab select the pit i gave you than go to AP and and go to where you extracted that tar and select it wait for it to check MD5 it may stop responding just wait than click start and wait for it to flash than you should be on stock unrooted lollipop
Click to expand...
Click to collapse
thank you, this helped me out when my odin got stuck for 30+ minutes.

I use to have a Note 4 Verizon good cell, but I then change it to a T-Mobile N910T unlock easer to flash them no boot-loaders are blocked, but thats just my saying.

I went through the process ... i have root and i can only install a 5.1.1 rom for the life of me i am unable to flash any 6 or 7 roms ... ideas?

Get write failure
I know this has been a couple years but I am in the same boat . I went through the steps and I get a flash write failure?
It happens after about 40 seconds into
system.img.ext4
ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> aboot.mbn
<ID:0/008> sbl1.mbn
<ID:0/008> rpm.mbn
<ID:0/008> tz.mbn
<ID:0/008> sdi.mbn
<ID:0/008> NON-HLOS.bin
<ID:0/008> boot.img
<ID:0/008> recovery.img
<ID:0/008> system.img.ext4
<ID:0/008> FAIL! (Write)
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Failing to install TWRP using Odin 3.12.3 (PrinceComsy)

Good morning everyone,
Having a bit of a hard time installing TWRP (3.0.2-1-gracelte.img) on this AT&T Note 7. I'm using PrinceComsy's Odin, disabling auto-reboot, checking AP and loading the recoveryimg, only to get the following error:
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> RQT_CLOSE !!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
As usual with things of this nature, I'm sure there's an obvious answer to why this is failing, but I can't seem to find it. Any help would be greatly appreciated.
Thank you,

kikokazuma said:
Good morning everyone,
Having a bit of a hard time installing TWRP (3.0.2-1-gracelte.img) on this AT&T Note 7. I'm using PrinceComsy's Odin, disabling auto-reboot, checking AP and loading the recoveryimg, only to get the following error:
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> RQT_CLOSE !!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
As usual with things of this nature, I'm sure there's an obvious answer to why this is failing, but I can't seem to find it. Any help would be greatly appreciated.
Thank you,
Click to expand...
Click to collapse
Well lol....its failing because there is no way to install twrp on a snapdragon note 7....jeez man where have you been since August lol?
Sent from my Note 7, S7 Edge or S6

force70 said:
Well lol....its failing because there is no way to install twrp on a snapdragon note 7....jeez man where have you been since August lol?
Sent from my Note 7, S7 Edge or S6
Click to expand...
Click to collapse
I knew it'd be a simple answer, lol. Thanks! Yeah well don't kill me for what I'm about to say - but I switched to an iPhone a while back. Blasphemous, I know. I'm still an Android fanboy at heart though!
I'm trying to help out a friend with his Note 7 since he wants to keep his before they toss the killswitch on it. Are there other ways to load a custom ROM onto it, or is he SOL?

kikokazuma said:
I knew it'd be a simple answer, lol. Thanks! Yeah well don't kill me for what I'm about to say - but I switched to an iPhone a while back. Blasphemous, I know. I'm still an Android fanboy at heart though!
I'm trying to help out a friend with his Note 7 since he wants to keep his before they toss the killswitch on it. Are there other ways to load a custom ROM onto it, or is he SOL?
Click to expand...
Click to collapse
If it's snapdragon no roms...
He can block the OTAs maybe using ADB but this will not help the imei kill

force70 said:
If it's snapdragon no roms...
He can block the OTAs maybe using ADB but this will not help the imei kill
Click to expand...
Click to collapse
Thanks. Folks over at N7A provided both an update blocker package and steps on spoofing the IMEI. Fortunately, IMEI bans haven't happened on AT&T just yet.

kikokazuma said:
Thanks. Folks over at N7A provided both an update blocker package and steps on spoofing the IMEI. Fortunately, IMEI bans haven't happened on AT&T just yet.
Click to expand...
Click to collapse
That forum us awesome, really great people there
Sent from my Note 7, S7 Edge or S6

I get the same for a Samsung A6 device... any ideas?
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 25 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)