Hey, all.
Before I installed the Malaysk ROM on the Eonon GA5151F in my Mazda 3, I remember there being an app for controlling the LCD screen. I never bothered with it because the full install requires Modding six wires and I wasn't ready for it yet. Last night I got in but the time is stuck and all it says is "Navi System."
What app will allow me to change the screen? Is it mtckeys? I tried that but can't get in to it and not sure where to find it in settings.
Is there a way to change what pops in the LCD screen itself? I read reports of others doing this but just haven't seen it myself yet.
Thank you!
supaneko said:
Hey, all.
Before I installed the Malaysk ROM on the Eonon GA5151F in my Mazda 3, I remember there being an app for controlling the LCD screen. I never bothered with it because the full install requires Modding six wires and I wasn't ready for it yet. Last night I got in but the time is stuck and all it says is "Navi System."
What app will allow me to change the screen? Is it mtckeys? I tried that but can't get in to it and not sure where to find it in settings.
Is there a way to change what pops in the LCD screen itself? I read reports of others doing this but just haven't seen it myself yet.
Thank you!
Click to expand...
Click to collapse
What exactly are u trying to change/modify on your screen? Can u be more specific?
ddoubled1 said:
What exactly are u trying to change/modify on your screen? Can u be more specific?
Click to expand...
Click to collapse
I am not looking to modify the screen on the HuiFei/Eonon unit itself. I am talking about the LCD screen that displays the clock, mileage, etc. that comes pre-installed in the Mazda 3. I have attached a pic as an example (it's that red thing above the receiver):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I want to change the time as well as know if there's a way to change the text that shows (the text in this one says "Home").
supaneko said:
I am not looking to modify the screen on the HuiFei/Eonon unit itself. I am talking about the LCD screen that displays the clock, mileage, etc. that comes pre-installed in the Mazda 3. I have attached a pic as an example (it's that red thing above the receiver):
I want to change the time as well as know if there's a way to change the text that shows (the text in this one says "Home").
Click to expand...
Click to collapse
Aha okay now i understand.. Do u remember the name of that app? Because i don't think it comes with Malaysk rom..
ddoubled1 said:
Aha okay now i understand.. Do u remember the name of that app? Because i don't think it comes with Malaysk rom..
Click to expand...
Click to collapse
That's what I was wondering. Does it just not come with the Malaysk app? Does anyone know what it is or was called?
I suppose I could reflash the original Eonon ROM and then reflash the Malaysk ROM but before I do, I'd like to see if I can locate the app first.
Thank you, ddoubled.
supaneko said:
That's what I was wondering. Does it just not come with the Malaysk app? Does anyone know what it is or was called?
I suppose I could reflash the original Eonon ROM and then reflash the Malaysk ROM but before I do, I'd like to see if I can locate the app first.
Thank you, ddoubled.
Click to expand...
Click to collapse
Try that, and if u can make a copy of the app, let us know.. Maybe Malaysk can make that an feature on his ROM's
supaneko said:
That's what I was wondering. Does it just not come with the Malaysk app? Does anyone know what it is or was called?
I suppose I could reflash the original Eonon ROM and then reflash the Malaysk ROM but before I do, I'd like to see if I can locate the app first.
Thank you, ddoubled.
Click to expand...
Click to collapse
What canbus decoder do you have? The black (MAZDA-RZ-01), the red MZD-SS-04 or the red MZD SS-02? If the last one you can set the clock and change the trip computer with a long press on the SWC Mode button. If one of the first two, you can handle the LCD over the Control settings app. It shows only if you select the Mazda&Opel (Simple) or Mazda&Opel (Raise) canbus option in Factory Settings.
But, you say just the NAVI SYSTEM shows. Did you make the wiring modification? Do you have a 2003-2005 Mazda3? After 2005 you don't have to modify the wiring.
I have the red CANBUS on a 2005 Mazda 3. I tried the long press of the MODE SWC button but it didn't work. I made the modifications. I think that the show of "NAVI SYSTEM" is a good start but ... that's it. I'll give it another go and see what happens.
peti007 said:
What canbus decoder do you have? The black (MAZDA-RZ-01), the red MZD-SS-04 or the red MZD SS-02? If the last one you can set the clock and change the trip computer with a long press on the SWC Mode button. If one of the first two, you can handle the LCD over the Control settings app. It shows only if you select the Mazda&Opel (Simple) or Mazda&Opel (Raise) canbus option in Factory Settings.
But, you say just the NAVI SYSTEM shows. Did you make the wiring modification? Do you have a 2003-2005 Mazda3? After 2005 you don't have to modify the wiring.
Click to expand...
Click to collapse
supaneko said:
I have the red CANBUS on a 2005 Mazda 3. I tried the long press of the MODE SWC button but it didn't work. I made the modifications. I think that the show of "NAVI SYSTEM" is a good start but ... that's it. I'll give it another go and see what happens.
Click to expand...
Click to collapse
Yes it is a good star. What is the part number of your red canbus? Can you take photos of modded connector and wires?
Alright ... WELLLLLL ... progress, sorta.
It was originally set to 14 (Mazda & Opel). My SWCs worked great with this setting. Then I changed them to 9 and they got all weird. Glitchy. I actually posted about it on a Mazda 3 forum and Eonon ended up sending me a new CANBUS because of the weirdness. Control Settings did end up showing but they're not controlling the LCD. Changed to 44 to try as well but the same problem persisted.
I do have the replacement CANBUS. peti, do you think I should try that? If it shows "other" (all lower-case), is this a "good" or not so good sign?
New CANBUS is:
SS-MZ023211238-0 ... or ZD(MZD-SS-02)20151119
I'll snap a photo when I get to the car.
Thanks, @peti007.
Swap for the new MZD-SS-02. With this you can handle clock settings and trip computer over the SWC, no need for any application on head unit. Change to 09 MAZDA&OPEL (Simple). The "other" is good with this canbus adapter.
peti007 said:
Swap for the new MZD-SS-02. With this you can handle clock settings and trip computer over the SWC, no need for any application on head unit. Change to 09 MAZDA&OPEL (Simple). The "other" is good with this canbus adapter.
Click to expand...
Click to collapse
Well this is wondrous news. Will give it a try.
They also sent a replacement wiring harness as a precaution. Should I swap this as well or just try it and see what's up?
The harness is different. If use the wrong one the reverse camera will not shown when you stick to reverse gear. So swap it too.
Tried it out and ... no change. Pressing the mode button as a long press just causes everything to cycle. Set to 9 and it didn't seem to change much. :\ Stuck on how to proceed.
Also, I've always got the reverse camera when sticking it in reverse.
The instructions say to connect the SW1 wire to the grey wire at the center of the Eonon harness. It makes no mention of SW2. As far as you know, is this correct? I am thinking of the video from here:
https://youtu.be/jZIsormC28A?t=1m2s
Alright ... I tossed it in there without making the mods just to see what would happen. When it's set to 9, it does this weird thing where sometimes it thinks the keys are being pressed twice. VOL+ works fine always but VOL- sometimes triggers VOL+ and MODE runs twice and sometimes acts as MUTE. Set it back to 14 and the problem goes away.
Without the SW1 connected, it does accept the long MODE press and triggers the LCD to say "Settings" (I think that's it) and makes a horrible, loud beep. Can't do anything beyond there it seems. Also, the software on the Eonon itself doesn't do much. I had this issue before Eonon sent me the replacement but it was 10x worse.
Once I get home, I'll solder the new wiring harness, assuming that's the proper thing to do.
Weird. I soldered the SW1 to the "center grey wire" and the MODE no longer causes the long beep. It still acts weird when set to 9. I changed to it 14 and it works fine ... well, except I can't control the LCD still. The Control Settings app is shown but it doesn't do anything either.
NAVI SYSTEM is now changing from that to "other" once the Eonon is booted up but ... that's as far as it seems to get.A
For reference, this is what I wired:
supaneko said:
Weird. I soldered the SW1 to the "center grey wire" and the MODE no longer causes the long beep. It still acts weird when set to 9. I changed to it 14 and it works fine ... well, except I can't control the LCD still. The Control Settings app is shown but it doesn't do anything either.
NAVI SYSTEM is now changing from that to "other" once the Eonon is booted up but ... that's as far as it seems to get.A
For reference, this is what I wired:
Click to expand...
Click to collapse
OK, what is your car's manufactured year? Where do you live? USA, Europe,...?
You don't have to solder the SW1 nor SW2 to anywhere in European Mazda3.
Please make photos of your wiring. Of the canbus adapter and of the 06-09 LCD wiring.
Erisin ES3095Z Stock Display
Hello,
I have bought this Android Car Audio (with built-in Dual Channel Can-Bus-Decoder)( Erisin ES3095Z) for my Mazda 3 2007. But the stock display don't work. It's only show "Navi System" with the bad clock). Impossible to set the time. I have try :
- Hold button "Mode" of Steering Wheel = No reaction
- Hold button "Setting"-"Mode" in the app of can bus = No reaction
- Repeat the previously action with the setting of can bus (Mazda/Opel Simple – Mazda/Opel Raise – Mazda/CX 5 – Mazda 3) = No reaction
Thank you for your help if you have a solution.
Geekry said:
the stock display don't work. It's only show "Navi System" with the bad clock). Impossible to set the time. I have try :
Click to expand...
Click to collapse
did you ever figure this out? I have the same issue with a 2012 mazda6. Eonon (w/ mtcb) support spent a /ton/ of time with me to figure out how to set the time (the rest of my LCD worked like fm radio station vs music track number vs whatever) but just can't set the time.
originally my steering wheel MODE button didnt do anything at all (besides make something beep) -- they had me cut the middle purple wire on the factory side of their harness and connected it to the brown KEY-5V wire. this made MODE work after i trained the buttons via the software app.
but i still can't set the time, they said that they can't figure out how to do it; that my best bet is to unplug the battery at 12:00. lame.
Related
Hi guys
I just got my hands on the clone called "HDC One MAX" (a.k.a. STAR One Max) with 5.9" MTK6582 16GB and Real IR remote control.
It is a perfect clone/replica of the known HTC One MAX 5.9" phablet.
I would like to start this thread to gather and collect as much info, tips & tricks, modifications, hacks etc. for this device as possible. Also the software/ROM on this phone is not 100% good yet, so I hope we can help each other fixing them.
First impressions:
The phone looks 1:1 to the original, this is one of the BEST clones I have ever seen - it even came in an original looking HTC box. Everything is 100% like on the original. The backcover and front speakers are made of real metal. The phone is also very heavy like the original. In matter for outer design they did a really good job.
It is equipped with 2 real front speakers, both speakers work! and they are actually pretty loud and nice. Still the quality is not near the original.
My phone came with the same bootup screen as the original and with all logos. Even the charger and USB cable is a perfect replica.
Overall the phone is very fast, and the UI almost looks like the real Sense from HTC. I am going to test it some more the next days, and write some extra later.
Unboxing video:
Review video:
Action presentation video:
Benchmarks:
Antutu 16855
Cons & pros
- Very nice clone, looks 1:1 and has almost same materials
- Very big and clear screen, good colors
- 2 real dual speakers on the front
- Real IR remote control that works
- Google play store works, same does the stock Youtube app
- It came with good accessories, screenprotector & hardcase
- 3G works (I am in Germany, and here it works fine)
- The touch can act a bit strange sometimes
- Google play services is having a conflict on this phone
- The price is in the high end because of the use of real metal
- The fingerprint scanner has no real function it seems (yet?)
- No backlight in the touchbuttons
Camera test
The camera is "OK" and typical Mediatek
http://peecee.dk/uploads/042014/2014-04-17_00.06.16.jpg
http://peecee.dk/uploads/042014/2014-04-16_23.48.04.jpg
http://peecee.dk/uploads/042014/2014-04-16_23.48.122.jpg
Tips & Tricks/Hacks
Can be rooted with latest Framaroot (select the last solution)
Can be backuped with MTK Droid Tools
Can install CWM via MTK Droid Tools
Issues
- The Google Play Services can not be updated together with Google Search, seems to be some kind of conflict on the phones software.
But I can use Youtube that was on the stock ROM when I got it, but I cant sign in. Still Google Play store works fine.
- Roaming warning can not be disabled in the options, but can be disabled with Xposed Framework and GravityBox.
- My homebutton can get unresponsive after I open the multitask overview (but turning off the screen, and on again, fixes the button again)
- After a factory reset and format of internal storage, I have lost the HTC bootup animation. I have the HTC One animation in my system/media, but for some reason the phone don't use it at bootup. It just bootup with a silverflashing "android" logo in the middle of the screen. Same with the shutdown animation. (I got my animations back with a CWM backup I made before I lost it)
The specifications (these should be the REAL specs, not the fake ones)
- Model: HDC One Max a.k.a STAR One MAX
- Display Size 5.9 inch / IPS / 1280*720 pixels
- Dual front speakers! both works, loud sound
- Band: 2G: GSM 850/900/1800/1900MHz / 3G: WCDMA 2100MHz
- Single Micro-Sim Card
- GPS with EPO assistance to speed up postioning
- Shell Material: Aluminium alloy (corners plastic)
- OS: Android 4.4 2 (looks like fake)
- UI: Sense 5.5 (I think fake, but it is 99% like the original)
- CPU: MTK6582, Quad Core, 1.3GHz
- GPU: Imagination PowerVR SGX 544MP
- 1GB RAM / 16GB ROM
- SD Card slot
- Net Weight (Including battery) 217g
- WIFI Yes, 802.11 b/g/n
- Youtube and Google Play Store works
- Dual Camera, front camera interpolation 5.0MP, back camera 13.0MP with flashlight and auto focus, up to 4096*3072 pixels resolution; support full screen capturing
Full http://peecee.dk/uploads/042014/DSC04068.JPG
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Full http://peecee.dk/uploads/042014/DSC04070.JPG
Full http://peecee.dk/uploads/042014/DSC04050.JPG
Updated now also with a full in-depth video review!
I like this phone.
Just picked this phone up! Should arrive tomorrow. Looking forward to what it's like.
Keep us updated on the updated ROM if one does come up :good:
reptech said:
Just picked this phone up! Should arrive tomorrow. Looking forward to what it's like.
Keep us updated on the updated ROM if one does come up :good:
Click to expand...
Click to collapse
I recommend you to make a backup as the first thing, when you get the phone. A CWM backup and maybe also a backup with MTKdroidtools.
I lost the bootup animation after I tried to do a factory reset of the phone. But because of my CWM backup I could get it back again.
Overall the phone is really nice, and I am currently also using Xposed Framework with Gravity box on it, works fine. But I still haven't been able to fix the Google apps, so they can be updated.
s7yler said:
I recommend you to make a backup as the first thing, when you get the phone. A CWM backup and maybe also a backup with MTKdroidtools.
I lost the bootup animation after I tried to do a factory reset of the phone. But because of my CWM backup I could get it back again.
Overall the phone is really nice, and I am currently also using Xposed Framework with Gravity box on it, works fine. But I still haven't been able to fix the Google apps, so they can be updated.
Click to expand...
Click to collapse
Oh sweet thanks for the tips... Will check out Xposed Framework and Gravity box.
and let me know if you have any other recommendations on apps and mods for the phone even if you do some more followup videos that'd be cool
Here my guide how to make a backup, use CWM and Spflashtool
http://forum.xda-developers.com/showthread.php?t=2730031
Signal weak
Hi just got the phone and the antenna signal is very weak, run out signal with other phones I've never had problems in my house.
know how to solve the problem? Thanks waiting for reply.
Alipi77 said:
Hi just got the phone and the antenna signal is very weak, run out signal with other phones I've never had problems in my house.
know how to solve the problem? Thanks waiting for reply.
Click to expand...
Click to collapse
Sorry but I don't have any antenna problems on mine. I always have good reception.
Did you try to switch from automode to only 2G for example?
s7yler said:
Sorry but I don't have any antenna problems on mine. I always have good reception.
Did you try to switch from automode to only 2G for example?
Click to expand...
Click to collapse
Change 2G and no resolved problem, bad reception, other telephone recepcion is good.
storage
Other problem, storage is only 2gb no 16 gb.
Alipi77 said:
Other problem, storage is only 2gb no 16 gb.
Click to expand...
Click to collapse
Check with Link2SD instead. I have 16GB REAL storage on mine, thats for sure.
From where you got yours?
storage
s7yler said:
Check with Link2SD instead. I have 16GB REAL storage on mine, thats for sure.
From where you got yours?
Click to expand...
Click to collapse
Buy phone big6seller, yesterday send message bigseller and you response "friend it have insert sd 16gb"
Alipi77 said:
Buy phone big6seller, yesterday send message bigseller and you response "friend it have insert sd 16gb"
Click to expand...
Click to collapse
It has 16GB ROM, did you try to make a factory reset?
Did you change or mod anything to the phone?
s7yler said:
It has 16GB ROM, did you try to make a factory reset?
Did you change or mod anything to the phone?
Click to expand...
Click to collapse
Recive Phone yesterday is new, no change no modify, and no factory reset.
I recommend Styler?
Alipi77 said:
Recive Phone yesterday is new, no change no modify, and no factory reset.
I recommend Styler?
Click to expand...
Click to collapse
What happens if you install Real Racing 3 and Asphalt 8? they are very big games.
s7yler said:
It has 16GB ROM, did you try to make a factory reset?
Did you change or mod anything to the phone?
Click to expand...
Click to collapse
s7yler said:
What happens if you install Real Racing 3 and Asphalt 8? they are very big games.
Click to expand...
Click to collapse
Real racing 3 no posible install, no MB disponible.
Alipi77 said:
Real racing 3 no posible install, no MB disponible.
Click to expand...
Click to collapse
What I would try is:
0. Make CWM backup off the original ROM, guide http://forum.xda-developers.com/showthread.php?t=2730031
1. Factory reset and format internal totally if possible (HTC boot may be lost!)
2. Download the stock ROM from Needrom http://www.needrom.com/mobile/11-one-max-mt6582/ and flash it to the phone with Spflashtool use guide here http://forum.xda-developers.com/showthread.php?t=2730031
If your phones ROM have been modified in some way before, it must at least be stock by now with the flashed stock ROM.
3. If still not ok, ask the seller for a solution or send it back.
s7yler said:
It sounds like the internal ROM is unmounted/damaged or changed for some reason on your phone.
It normally should have at least 14.39 GB internal storage available.
You didnt change anything to the EBR files or? I guess not.
What I would try is:
0. Make CWM backup off the original ROM, guide http://forum.xda-developers.com/showthread.php?t=2730031
1. Factory reset and format internal totally if possible (HTC boot may be lost!)
2. Download the stock ROM from Needrom http://www.needrom.com/mobile/11-one-max-mt6582/ and flash it to the phone with Spflashtool use guide here http://forum.xda-developers.com/showthread.php?t=2730031
If your phones ROM have been modified in some way before, it must at least be stock by now with the flashed stock ROM.
3. If still not ok, ask the seller for a solution or send it back.
Click to expand...
Click to collapse
is quite complicated for me to do all this and not know much about computer, my English is bad sted could help me via teamviewer paying?
Thanks styler.
have problem with my htc one max clone
i flashed my htc one max clone with flashify app
i think i have a boot loader problem
adb sideload only recognize the phone when it is connected to my pc
i tried insalling roms but each is not working but i can acess my recovery
can any one help?
or can i get the default android os
Hi,
I was wondering if I can change the functionality of the buttons which are placed on the unit. It would be great if I could change the NAV button to open not the iGo navigation but Google Maps.
Can you help me?
Kind regards
airchicken said:
Hi,
I was wondering if I can change the functionality of the buttons which are placed on the unit. It would be great if I could change the NAV button to open not the iGo navigation but Google Maps.
Can you help me?
Kind regards
Click to expand...
Click to collapse
Do you tried to enter the Settings, then GPS section, and changing there the associated application?
Which settings do you mean? Android Settings or Device Settings (which are secured by the code)
airchicken said:
Which settings do you mean? Android Settings or Device Settings (which are secured by the code)
Click to expand...
Click to collapse
Android settings and then GPS section
Okay, that might be a possible solution to change the NAV button. But how to change the other buttons?
airchicken said:
Okay, that might be a possible solution to change the NAV button. But how to change the other buttons?
Click to expand...
Click to collapse
On my unit I have the following buttons: MENU, DISC, NAVI, DIMM and BAND. I don't know which button can be still redefined, but the only solution (if there is any) I think it could be using a custom ROM.
In my opinion, there should be a configuration file anywhere. But I could not yet find it...
BTW: I have MENU, SETUP, >>|, RADIO, DVD, GPS
airchicken said:
In my opinion, there should be a configuration file anywhere. But I could not yet find it...
BTW: I have MENU, SETUP, >>|, RADIO, DVD, GPS
Click to expand...
Click to collapse
So, which other buttons would you like to redefine and with which other features?
I'd like to put a music player on the DVD Button, as I never watch a DVD in my car...
airchicken said:
I'd like to put a music player on the DVD Button, as I never watch a DVD in my car...
Click to expand...
Click to collapse
Do you have already installed a custom ROM on your unit? Take a look also in the device's Factory settings with the secure code. Such a redefining should be possible.
No, it's still stock...
I couldn't find anything in factory settings...
airchicken said:
No, it's still stock...
I couldn't find anything in factory settings...
Click to expand...
Click to collapse
OK, then I think that it could be possible only with the custom ROM or by root access.
I'm still on stock ROM too, and I would like to make a complete backup of the original ROM before installing the custom one.
That would be good. But as I'm on root, I should be able to change the necessary configuration files...
How do you managed yo get root access without custom ROM? Which is the exact type of your unit and the MCU version?
I had to sideload some things and install an app to root it - don't know exactly anymore.
Will tell you the MCU later this afternoon
Use MTC-Keys to remap buttons
Read links for install and setup
http://forum.xda-developers.com/android-auto/mtcb-software-development/xposed-modules-units-t3263966
http://forum.xda-developers.com/showthread.php?p=60941619#post60941619
Link just in case the embedding doesn't work.
Youtube Link: https://youtu.be/SzP-soM7cqA
TOP: PX3
5.1.1
MTCD_GS_V1.49_1 Apr28 2016
RK 3188
Mali400
4x1.6ghz
1GB RAM
16GB ROM
1024x600
Bottom: PX5]
6.0.1
MTCD_GS_V2.11_1 Jan7 2017
RK 3368
PowerVR G6110
4x1.2-1.5ghz
2GB RAM
32GB ROM
1024x600
First time shooting a video like this, I can post an update but I'll throw all my findings here.
Some if my initial issues;
With the MTCD PX3 5.1.1 RK3188 You could change the ACC timeout so that the unit would stay on for a specified time, that is no longer in the menu. (Car was off for 3hours and it still fast started so drawing current constantly)
Radio constantly resets after turning the key off even though the Headunit only goes into sleep it's still resetting all radio stations.
Some applications in the Google play store report they are not compatible with this unit ie: iGO Navigation. I had to side load it but that's causing issues with the sys.txt file.
The launcher is damn ugly...
Always says failed to download license when coming out of sleep even with WIFI & 4G connectivity.
(Will update as I use it more)
Positives;
Unable to make it slowdown with Spotify & iGO Navigation running at the same time like it used to.
Audio quality is a LOT better and having subwoofer control on the EQ is great.
No longer have engine whine/hiss either.
(Will update as I use it more)
Antutu benchmark comparison:
PX3:
Overall: 27808
3d: 1220
UX: 13079
CPU: 10293
RAM: 3216
PX5:
Overall: 39047
3d: 9019
UX: 13397
CPU: 12768
RAM: 3863
Please feel free to ask any questions etc.
Cheers
Mat
You should measure the power draw when it has been off for an hour or more. The Intel head units basically goes to a deep hibernation, drawing next to nothing (no more than a normal head unit) while the system is sleeping, and then it comes instantly back on and is ready to use within a second or two from turning on the ignition. It may be that the new PX5 has a similar or the same feature, which is why you don't set the ACC timeout anymore. On the Joying Intel units you can change it between what they call "dormancy" or "shut off" in the special settings app they have, allowing you to turn it all the way off when ACC is removed if you wish to do so.
Hilari0 said:
You should measure the power draw when it has been off for an hour or more. The Intel head units basically goes to a deep hibernation, drawing next to nothing (no more than a normal head unit) while the system is sleeping, and then it comes instantly back on and is ready to use within a second or two from turning on the ignition. It may be that the new PX5 has a similar or the same feature, which is why you don't set the ACC timeout anymore. On the Joying Intel units you can change it between what they call "dormancy" or "shut off" in the special settings app they have, allowing you to turn it all the way off when ACC is removed if you wish to do so.
Click to expand...
Click to collapse
Thanks for the idea, I have a DC clamp meter I'll use tomorrow to double check.
Just tried the ignition again after getting home from being out with friends. So the car was off for 6 1/2hours this time, hit the key & it instantly started.
Still not happy about it resetting the radio stations every time however.
Cheers
Mat
Edit: also showing an issue I'm receiving, PX3 top, PX5 bottom.
The 6.0.1 Octacore has a lot of apps that it's not "compatible" with.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
On Intel MTCD devices, they removed the option to set ACC off timer.... due to the power consumption during deep sleep is negligible. I think some ROM update is neccessary to fix that small errors
It is strange that lots of apps were not compatible with the device as it is a RK3368 (two years old chip). Perhaps is sending a wrong device information to Google play ?
good review. Sound like a fellow kiwi? note that other resellers offer MCU and ROM upgrade on rk3188 to enable sub control. e.g. jy1.90
Hi,
About..
=> and having subwoofer control on the EQ is great. <=
Mine Xtrons pic..
(Never.. Buy an Xtrons hu again.. Bad support and to slow communication via email too.. excuses after excuses received!!)
Anyway: have fun with it
BrGd
Madyen
I like that new launcher!
ikerg said:
On Intel MTCD devices, they removed the option to set ACC off timer.... due to the power consumption during deep sleep is negligible. I think some ROM update is neccessary to fix that small errors
It is strange that lots of apps were not compatible with the device as it is a RK3368 (two years old chip). Perhaps is sending a wrong device information to Google play ?
Click to expand...
Click to collapse
Ok did some clamp DC current tests,
Headunit unplugged. vehicle left for an hour. 37-55mA current draw tested 3 times in 15minute period.
Headunit plugged in, sleeping 3hours then clamped. 97-130mA. That's a noticeable drain increase, that's enough to make a vehicle not start if it hasn't been driven in a week.
An ACC timeout adjustment would be great again. Lets say the unit locks up? My older unit would lockup every now and then and just be the wallpaper on screen (launcher crash) and I'd have to turn ignition off the ACC timeout time to reboot the headunit properly.
What happens now? Do I have to go pulling fuses.
And for the device information all it does is report as PX5, Where as the PX3 reports at RK3188. So I have a feeling that's an issue?
Hopefully updates get dropped soon through various vendors as at the end of the day they're all the same generic core board.
Cheers
Mat
hi.
have you managed to gain root access on the unit
Soo...
I think difference too small to upgrade PX3 to PX5.
On PX3 we can turn off all google services and enjoy fast HU
RazGame said:
Soo...
I think difference too small to upgrade PX3 to PX5.
On PX3 we can turn off all google services and enjoy fast HU
Click to expand...
Click to collapse
PX5 aside, the upgraded memory to 2gb is a major factor and provides an out of the box experience without feature limiting mods that may be difficult for some.
Note that I have upgraded my rk3188 to 2gb which improves the unit from boot to opening multiple apps and do not see the cpu as a bottleneck at all.
Seems to me the PX5 isn't ready for prime time as of yet, I'll stick to recommending the Intel for the time being. The power usage when sleeping is disconcerting, the Intel units draw something like 12-13 mA when in sleep mode, which is really great! That is actually a major feature for me, as I'd be annoyed waiting a minute or so for the thing to boot up in the morning.
Bit of an update, Had a few scenarios where radio has not reset now. I can't figure out what aspect causes it to reset but it does happen occasionally between a key cycle.
Apart from the launcher look which I hate I've warmed up to the unit. App switching, Spotify buttons are already linked to << >> > || etc. Haven't been able to lag the volume control, or GPS/Spotify/Pandora switching etc.
Appears With my usage It hovers around 900Mb Ram usage, so there is a chance the biggest change I'm noticing is the memory being 2GB now vs 1GB.
But does anyone have info about the DSP on these units? It sounds a lot clearer and less muddy now which is odd, I wasn't sure that was a change. But It's a welcomed one.
Any questions feel free to ask.
Cheers
Mat
Thanks for all the info
Is there any reference to the voltage on the RCA outputs on the unit? Is it too much to hope that with an improved DSP they can put out a bit more than the old 2V?
Sound quality wise does the unit seem more inline with more established aftermarket units now like Alpine etc (if you have any experience with them), Whats the main difference here?
Okay, I have some info on the MTCD 6.X.X MCU/Software Updates etc.
I also have the update.img & dmcu.img for 12th Jan 2017 for the PX5 unit. (According to Xtrons support, I haven't used yet.)
Link: https://dl.dropboxusercontent.com/u/876493/XDA/PB系列 Android 6.0 软件 (20170112 ).rar
If someone can host? I can temporarily dropbox them.
Cheers
Mat
The following is a Google translate of the .txt doc
2016-12-26
----------
**- Fixed "occlusion" of the weather application search box text
**- Repair Media DVD, up and down keys function
**- Adds interface hints for system high temperature testing
2016-12-27
----------
**- Update the text strong blue BC6, BC8 sdk, optimize the startup speed;
2016-12-29
----------
**- Update the text of strong Bluetooth BC6, BC8 sdk, handle Bluetooth music software reported information error is mistaken for A2DP service disconnected;
2016-12-30
----------
**- Update the exception of APP external device VOL
2017-1-3
----------
**- Repair the radio boot, fast access to non-frequency display problem
2017-1-4
----------
**- Fixes the problem of getting the third-party interface part to get the wrong state
**- Update the kernel CVBS system switch bug
2017-1-5
----------
**- Update the kernel OTG USB bug
**- Update the text strong Bluetooth BC6, to solve the problem of ringtones and dial-up crosstalk;
**- Update the drive recorder watermark display
**- Update the kernel touch screen GT911 bug
2017-1-6
----------
**- Synchronize RK code,
**- Repair USB recovery part of the upgrade can not, the version number changes to V6.0.7
**- Remove the RK's own watermark, making MJPEG and H264 USB display the same way
2017-1-7
----------
**- KERNEL update, repair the boot screen darkening and then restore the issue, G-SENSOR support (yet to be perfect)
2017-1-9
**Music to DVD crosstalk problem
**- Delete the recorder
**- Undo deleted google voice in previous version
**- KERNEL, G-sendor and 4g version of the conflict bug
**- KERNEL, Config for TPMS & BACKSCREEN
**- Release the Bluetooth phone, HOME, BACK, and other key restrictions
2017-1-10
**- Added ZTE MF833V 4G dangle support
**- modify the Bluetooth call state can operate the machine other applications (public version of the Bluetooth application)
In this case,
2017-1-11
**- Update Wenqiang MD725 Bluetooth OBD;
**- Update recovery V6.0.7, fix manually selected MCU upgrade unsuccessful BUG
**- Update Settings application to detect MCU upgrade file error
2017-1-12
**- Tire pressure built-in according to factory factory settings
**- Update billion even USB crash problem
**- Update the network video playback problem
**- Fixed "open the radio in the rear view, close the ACC, will re-open ACC, exit the rear view as the radio, the radio did not sound" problem
Click to expand...
Click to collapse
Hi,
(((excuse me)))
I have not previously responded to your "review" between these 2 hu because I felt it unfair to compare them both like the way you already did.. is not an honestly comparing -and maybe you knew it?- mate!!
Prove it.. you gonna or I hear you say.. right?
Ok here we go..
How it is possible in the Xtrons name that you compare both hu while you did not even have updated your old 5.1 hu at all?
Your 5.1 hu with an very old fw and mcu version while the newer 6.1 hu one is with the most newer fw and mcu come? now is that comparing you called fair
I don't know why you did it that? But maybe.. I may have my own thought of kind of conspiracy but I will keep it for myself and I don't tell it ofcourse
If you are really wanted to comparing both of them honestly then you should first of all update your old hu one first and then compare it with the newer one.. right?
TOP: PX3
5.1.1
MTCD_GS_V1.49_1 Apr28 2016
Bottom: PX5
6.0.1
MTCD_GS_V2.11_1 Jan7 2017
Long live the Xtrons king :laugh:
Have fun mate.
BrGd
Madyen
Madyen said:
Hi,
(((excuse me)))
I have not previously responded to your "review" between these 2 hu because I felt it unfair to compare them both like the way you already did.. is not an honestly comparing -and maybe you knew it?- mate!!
Prove it.. you gonna or I hear you say.. right?
Ok here we go..
How it is possible in the Xtrons name that you compare both hu while you did not even have updated your old 5.1 hu at all?
Your 5.1 hu with an very old fw and mcu version while the newer 6.1 hu one is with the most newer fw and mcu come? now is that comparing you called fair
I don't know why you did it that? But maybe.. I may have my own thought of kind of conspiracy but I will keep it for myself and I don't tell it ofcourse
If you are really wanted to comparing both of them honestly then you should first of all update your old hu one first and then compare it with the newer one.. right?
TOP: PX3
5.1.1
MTCD_GS_V1.49_1 Apr28 2016
Bottom: PX5
6.0.1
MTCD_GS_V2.11_1 Jan7 2017
Long live the Xtrons king :laugh:
Have fun mate.
BrGd
Madyen
Click to expand...
Click to collapse
I was comparing my 2 units, What I removed and what I was installing.
I think you care a little too much.
Cheers
Mat
Madyen said:
Indeed, if you say so, you knew about this and that but never know about an update of an new fw for your own hu and you keep it working and used with an very old fw?.. come on mate.. is that a joke?
As I said, Long live the Xtrons king
BrGd
Madyen
Click to expand...
Click to collapse
You're still making no sense. It's a vehicle specific fit unit, if another manufacturer did a PX5 version to suit I'd of purchased that.
I got my PX3 unit In September, Car didn't get driven between Early December-Mid January due to me breaking my wrist and having it pinned.
I still don't see what you're getting at, but okay. Take your salt elsewhere bud.
Cheers
Mat
FauxDreams said:
You're still making no sense. It's a vehicle specific fit unit, if another manufacturer did a PX5 version to suit I'd of purchased that.
I got my PX3 unit In September, Car didn't get driven between Early December-Mid January due to me breaking my wrist and having it pinned.
I still don't see what you're getting at, but okay. Take your salt elsewhere bud.
Cheers
Mat
Click to expand...
Click to collapse
It is better comparison by having both units completely updated to the last versions of mcu and firmware.
Lots of issues are related to mcu and the one for ypur px3 is very old
if I did help you, please hit "thanks" button
ikerg said:
It is better comparison by having both units completely updated to the last versions of mcu and firmware.
Lots of issues are related to mcu and the one for ypur px3 is very old
if I did help you, please hit "thanks" button
Click to expand...
Click to collapse
The PX3 is already sold, It's why I bought the PX5. I had about an hour with the PX3 after removing it before it got picked up.
Cheers
Mat
Some time ago I ordered a px6 Max10 with 720p screen. The lcd screen somehow broke in the mail (I think they knowingly sent it to me broken... but that's just my opinion), and I sent them pictures of this. Dasaita sent me a new screen... or at least they were SUPPOSED to. A month and a half later (today) the WRONG part arrived in my mailbox. They sent me the outer glass instead of a new 720p screen. So here I am more than 2 months after I ordered this thing, it is STILL not in my vehicle. I am sooo friggin angry!
Anyway, I sent them an email but we're probably talking yet another 6 to 8 weeks... and that's if they get it right this time, which I doubt. I am fast coming to the conclusion these people are slightly less than honest.... but that's another thread.
I was thinking....
I do have a Dasaita px5 with a 1024x600 screen. Would it be possible just to take the screen off the px5 and stick it on the px6? This might be far easier than expecting much more from Dasaita at this point. After seeing what I saw today in the mail that they sent me, I don't think I am ever going to see a working 720p screen out of them. I have a feeling they are just going to jerk me around until I get tired of trying.
if they are thesame dimension...the only thing really is just flash the right file for the specific resolution
ojuniour said:
if they are thesame dimension...the only thing really is just flash the right file for the specific resolution
Click to expand...
Click to collapse
Yeah that's what I thought. I'm pretty sure the two screens are the same physical dimensions, and I believe the connections are all the same so its just a matter of flashing with the correct resolution.
Bob_Sanders said:
Yeah that's what I thought. I'm pretty sure the two screens are the same physical dimensions, and I believe the connections are all the same so its just a matter of flashing with the correct resolution.
Click to expand...
Click to collapse
Then just flash the 1024x600 update file (including the MCU if necessary )
May be useful to have a 2nd screen handy that you can connect over HDMI to see what you are doing when you try to flash different screen resolutions. For 1024x600 I think you need to flash a dmcu.ext file with "screen:2" in it.
Noway
woggles said:
May be useful to have a 2nd screen handy that you can connect over HDMI to see what you are doing when you try to flash different screen resolutions. For 1024x600 I think you need to flash a dmcu.ext file with "screen:2" in it.
Click to expand...
Click to collapse
Hi woggles,
I am new here, so please excuse me , if my question is stupid.
First, seems I have the same issue. I have PX6 , and the seller recently send me an update containing dmcu and update. files.
I did the upgrade and this almost brick my head unit. So, my display stop working, it have vertical lines , and flicking. My hardware buttons has lost its orders , for example home button become "power" button, and so on. Touch positions on the screen also are displaced. The screen constantly scrolling itself. Error message appear shows Version Unmatch -01.
I plug external HDMI monitor , and there all looks fine. So the issue is in the LCD display .
Then I update dmcu with newest version , and this error message disappear , but I still have issue with the LCD. Tried several update versions, but so far without success. Attaching pictures.
I think that the issue is in the screen resolution do not match , or LCD hardware issue, that is why I would ask you - how to flash dmcu with screen option ? My screen resolution should be 1280*720
Many thanks !
ps. unfortunately I cant attach an image, as new member
HighWay7777 said:
Hi woggles,
I am new here, so please excuse me , if my question is stupid.
First, seems I have the same issue. I have PX6 , and the seller recently send me an update containing dmcu and update. files.
I did the upgrade and this almost brick my head unit. So, my display stop working, it have vertical lines , and flicking. My hardware buttons has lost its orders , for example home button become "power" button, and so on. Touch positions on the screen also are displaced. The screen constantly scrolling itself. Error message appear shows Version Unmatch -01.
I plug external HDMI monitor , and there all looks fine. So the issue is in the LCD display .
Then I update dmcu with newest version , and this error message disappear , but I still have issue with the LCD. Tried several update versions, but so far without success. Attaching pictures.
I think that the issue is in the screen resolution do not match , or LCD hardware issue, that is why I would ask you - how to flash dmcu with screen option ? My screen resolution should be 1280*720
Many thanks !
ps. unfortunately I cant attach an image, as new member
Click to expand...
Click to collapse
To update the screen configuration you need to flash the dmcu.img along with a dmcu.ext file. You need to put both files on a FAT32 USB flash disk and you can upgrade MCU through the system settings menu or in recovery. The dmcu.ext file can contain the screen configuration and is simply a plain text file containing "screen:x".
For 1280x720 try the following screen values (upgrading MCU each time).
"screen:12" this resulted in blank screen for me
"screen:13" this works for me in all roms but I get one half line that flickers on the top left.
"screen:16" I never tried this, support mentioned it to me
"screen:18" only works for HA firmware 20190915 or newer but has the best results.
I would try 13 first, but I'm not sure if you have same display as me.
Good luck!
woggles said:
To update the screen configuration you need to flash the dmcu.img along with a dmcu.ext file. You need to put both files on a FAT32 USB flash disk and you can upgrade MCU through the system settings menu or in recovery. The dmcu.ext file can contain the screen configuration and is simply a plain text file containing "screen:x".
For 1280x720 try the following screen values (upgrading MCU each time).
"screen:12" this resulted in blank screen for me
"screen:13" this works for me in all roms but I get one half line that flickers on the top left.
"screen:16" I never tried this, support mentioned it to me
"screen:18" only works for HA firmware 20190915 or newer but has the best results.
I would try 13 first, but I'm not sure if you have same display as me.
Good luck!
Click to expand...
Click to collapse
May thanks ! I was able to recover screen settings !
For me "screen:12" working fine
Regards,
woggles said:
To update the screen configuration you need to flash the dmcu.img along with a dmcu.ext file. You need to put both files on a FAT32 USB flash disk and you can upgrade MCU through the system settings menu or in recovery. The dmcu.ext file can contain the screen configuration and is simply a plain text file containing "screen:x".
For 1280x720 try the following screen values (upgrading MCU each time).
"screen:12" this resulted in blank screen for me
"screen:13" this works for me in all roms but I get one half line that flickers on the top left.
"screen:16" I never tried this, support mentioned it to me
"screen:18" only works for HA firmware 20190915 or newer but has the best results.
I would try 13 first, but I'm not sure if you have same display as me.
Good luck!
Click to expand...
Click to collapse
Great post.
Some time ago I received a replacement screen panel and apparently it has a resolution of 1280x720, so I installed it ,but the image doesn't fit the screen. I have tried that dmcu ext file ,but the only value that works is screen:12,,,,,any ideas?
Al Ferro said:
Some time ago I received a replacement screen panel and apparently it has a resolution of 1280x720, so I installed it ,but the image doesn't fit the screen. I have tried that dmcu ext file ,but the only value that works is screen:12,,,,,any ideas?
Click to expand...
Click to collapse
Just using reverse thinking on this.....
Wouldn't a bigger image indicate a SMALLER screen? Are you sure the screen resolution is 1280x720 and not 1024x600?
Screen:2 I think is the 1024x600 if you want to try that. Just make sure you can get out of it without the screen just in case it goes blank.
Bob_Sanders said:
Just using reverse thinking on this.....
Wouldn't a bigger image indicate a SMALLER screen? Are you sure the screen resolution is 1280x720 and not 1024x600?
Screen:2 I think is the 1024x600 if you want to try that. Just make sure you can get out of it without the screen just in case it goes blank.
Click to expand...
Click to collapse
When they sent me the new screen they said it was 1280x720, and when I installed it I checked and it showed 1280x720 in settings. There is a setting in factory settings by the name of "Customer Version" and it's referred to the screen version or resolution , Version 1 and Version 2,,,,,,,,I saw somewhere to never change it to version 2 or it will be a blank screen . I did not try to flash the mcu with dmcu ext screen:1, I will try that later.:good:
.
.
Al Ferro said:
When they sent me the new screen they said it was 1280x720, and when I installed it I checked and it showed 1280x720 in settings. There is a setting in factory settings by the name of "Customer Version" and it's referred to the screen version or resolution , Version 1 and Version 2,,,,,,,,I saw somewhere to never change it to version 2 or it will be a blank screen . I did not try to flash the mcu with dmcu ext screen:1, I will try that later.:good:
Click to expand...
Click to collapse
Here is my experience with this similar issue. After figuring out the the dmcu.ext is basically a text file and the only thing in it is screen:x x being a number. The number representing a resolution in relation to what MCU and OS. The default of 1280x720 is 12 on all of the dmcu.ext I could download. I read in most people changing it to 18 depending on which MCU you have installed is what i read. I also was not doing a factory reset erase all before I did an install. So I did the factory reset and the dmcu.ext with screen 12. nothing happened. I did it again with 18 nothing. The 3rd factory reset with screen:0 and on all of these I was using MTCE_HA_V3.62 for dmcu.img. When this one rebooted it had a black screen. I plugged a monitor to the hdmi output and I could see through the monitor just fime but I had to touch my head unit screen where I think it should be according to the monitor so I factory reset again with screen:13 in the dmcu.ext and when the head unit rebooted after installing it was the correct resolution..
sitealpha said:
Here is my experience with this similar issue. After figuring out the the dmcu.ext is basically a text file and the only thing in it is screen:x x being a number. The number representing a resolution in relation to what MCU and OS. The default of 1280x720 is 12 on all of the dmcu.ext I could download. I read in most people changing it to 18 depending on which MCU you have installed is what i read. I also was not doing a factory reset erase all before I did an install. So I did the factory reset and the dmcu.ext with screen 12. nothing happened. I did it again with 18 nothing. The 3rd factory reset with screen:0 and on all of these I was using MTCE_HA_V3.62 for dmcu.img. When this one rebooted it had a black screen. I plugged a monitor to the hdmi output and I could see through the monitor just fime but I had to touch my head unit screen where I think it should be according to the monitor so I factory reset again with screen:13 in the dmcu.ext and when the head unit rebooted after installing it was the correct resolution..
Click to expand...
Click to collapse
Did you use one of the pre-made display fix files on the Russian yandisk repository?
HighWay7777 said:
May thanks ! I was able to recover screen settings !
For me "screen:12" working fine
Regards,
Click to expand...
Click to collapse
Where did u get the .ext and .IMG files from?
My screen is 1024x600
Thanks for the help
kiwibird said:
Where did u get the .ext and .IMG files from?
My screen is 1024x600
Thanks for the help
Click to expand...
Click to collapse
From reading the forums and contributing, probably FFS.
marchnz said:
From reading the forums and contributing, probably FFS.
Click to expand...
Click to collapse
I tried to look for the right files but wasn't successful. But what do you mean by probably FFS??
kiwibird said:
Where did u get the .ext and .IMG files from?
My screen is 1024x600
Thanks for the help
Click to expand...
Click to collapse
I had the same issue and it took forever finding it. Just rename either dmcu.ext. I tried editing the other, the depository I used no longer existed and any Google search came here.
The new place were I got the dmcu.ext file.
Yandex
Finds everything
disk.yandex.com
11/05/2022: UPDATED the instructions and the rules.
NOTICE: This method is no longer relevant for the U2-baseband firmware and Android 13-based GSIs, they should work out of the box.
After a couple of weeks of the real-world use of SM-A325 with LineageOS GSI installed, I've found that the phone has no real proximity sensor and that's a real problem. The so called "virtual" proximity sensor mentioned by Samsung is obviously just an emulation done by reading the tilt sensor (vertical position) and the touchscreen (touch anywhere in the upper half).
Almost all of the GSIs use the generic Call app, so just a slight accidental touch with your ear or finger and you can have a whole bunch of functions activated. There is a solution though:
Install the "Automation" app (open-source) by Jens Schröder
Go to the "Rules" tab and press "Add Rule"
Give the new rule some name (e.g. "Turn screen off during call")
Press "Add trigger", "Phone call", "State" = "started", "Call direction" = "any". Press "Save".
Press "Add action", "Turn screen on or off", "Deactivate"
"Save Rule"
If the rule is marked with the yellow dot go to the "Overview" tab, start the service and give the needed permissions
Also press "Control center", "Settings" and make sure that "Start at system boot" is checked.
And another, mode advanced version (if that's too complicated you can just import the attached settings file):
Go to the "Rules" tab and press "Add Rule"
Give the new rule some name (e.g. "Turn screen off during call")
Press "Add trigger", "Phone call", "State" = "started", "Call direction" = "any". Press "Save".
Press "Add trigger", "Device orientation"
Position the phone vertically (Pitch = 0±5) and press "Apply"
Enter tolerances: 180, 70, 180
"Must apply" checked
Press "Save"
Press "Add trigger", "Screen state", "on"
Press "Add action", "Turn screen on or off", "Deactivate"
"Save Rule"
I recommend setting "Signal frequency" in "Device orientation settings" in the settings to 500 ms. This way there will be much lesser chance of lag when phone is lifted up to the ear, while the battery consumption by the Automation app will still remain negligible.
That's it. Now when you receive a call the screen will be turned off. You can turn it on during the call by pressing the side button, the call will not be interruped. When using the advanced version of the rules the side button works only when the device is held horizontally, unfortunately there is no way to improve this but I think that is a very minor issue (or just use the simple version instead).
Updated rules, working with Automation v1.7.6.
This causes an issue in video calling on whatsapp where the phone turns the screen off again and again.
Captain_cookie_200 said:
This causes an issue in video calling on whatsapp where the phone turns the screen off again and again.
Click to expand...
Click to collapse
Try the rule that I am using now. It's much simpler and much more reliable. If it does not work for you then probably this solution is just incompatible with WhatsApp. BTW, I am not using it and don't recommend to anyone as it's the privacy-violating app.
uluruman said:
Try the rule that I am using now. It's much simpler and much more reliable. If it does not work for you then probably this solution is just incompatible with WhatsApp. BTW, I am not using it and don't recommend to anyone as it's the privacy-violating app.
Click to expand...
Click to collapse
oh. btw how do i import these files??? and that small brown message sooo your living without screen turning off on its own? and privacy invading.... WAIT WAS IT TRACKING MY STUFF ALL ALONG?
Captain_cookie_200 said:
oh. btw how do i import these files??? and that small brown message sooo your living without screen turning off on its own? and privacy invading.... WAIT WAS IT TRACKING MY STUFF ALL ALONG?
Click to expand...
Click to collapse
Any free commercial app is doing this. That's why it's free.
uluruman said:
Any free commercial app is doing this. That's why it's free.
Click to expand...
Click to collapse
but aint this open source. its on the f droid store. and over there, there are only open source apps.
and how do i import it btw. the xml file. thanksss
To import the rules put them in some folder, start Automation, press Control center, Import configuration and choose that folder.
Captain_cookie_200 said:
but aint this open source. its on the f droid store. and over there, there are only open source apps.
Click to expand...
Click to collapse
I was talking about WhatsApp, of course.
uluruman said:
I was talking about WhatsApp, of course.
Click to expand...
Click to collapse
oh yes... whatsapp... i am forced because of my school groups and my whole family using it.. otherwise i would ditch it. anyways thanks for your time
It seems that this problem is no longer present at least with the latest Android 13 stock firmware (A325FXXU2CVK3) or even slightly older used together with LineageOS 20.0 or even 19.0. Using the Android 13 firmware also cures another long-standing issue - the non-functional MTP file transfer. Analyzing the kernel source reveals that Samsung obviously abandoned their own f_mtp_samsung driver in favor of the standard f_mtp.
uluruman said:
It seems that this problem is no longer present at least with the latest Android 13 stock firmware (A325FXXU2CVK3) or even slightly older used together with LineageOS 20.0 or even 19.0. Using the Android 13 firmware also cures another long-standing issue - the non-functional MTP file transfer. Analyzing the kernel source reveals that Samsung obviously abandoned their own f_mtp_samsung driver in favor of the standard f_mtp.
Click to expand...
Click to collapse
i am aware. unfortunately gsi's lag alot on android 13 and i was getting almost 1 fps on hill climb racing. yep. i dont know why... thats why im sticking to android 11 firmware.
Captain_cookie_200 said:
i am aware. unfortunately gsi's lag alot on android 13 and i was getting almost 1 fps on hill climb racing. yep. i dont know why... thats why im sticking to android 11 firmware.
Click to expand...
Click to collapse
Hmm. I'm currently using Lineage 20.0 (td version) installed upon the unaltered A325FXXU2CVK3 firmware and I didn't notice any difference in performance.
uluruman said:
Hmm. I'm currently using Lineage 20.0 (td version) installed upon the unaltered A325FXXU2CVK3 firmware and I didn't notice any difference in performance.
Click to expand...
Click to collapse
i see. there was a huge performance drop for me
@uluruman
Hi! First of all sorry for my mechanic English hehehe.
I just broke my proximity sensor cause water... , Now im trying this method but I have a question.
Exist some way to put audio in the calls speaker ( the topside speaker used in calls)? For example, I want to listen some Whatsapp audio in private.
I want to put the smartphone on my ear and then automation change the speaker, besides turn off the screen.
I didn't saw any option, just the script option that I don't know how to use it and the "boardcast" option that i dont know how to use it neither.
Thanks in advance.
ADDJ69 said:
@uluruman
Hi! First of all sorry for my mechanic English hehehe.
I just broke my proximity sensor cause water... , Now im trying this method but I have a question.
Exist some way to put audio in the calls speaker ( the topside speaker used in calls)? For example, I want to listen some Whatsapp audio in private.
I want to put the smartphone on my ear and then automation change the speaker, besides turn off the screen.
I didn't saw any option, just the script option that I don't know how to use it and the "boardcast" option that i dont know how to use it neither.
Thanks in advance.
Click to expand...
Click to collapse
I am sure that Automation can't do that, changing whatever speaker is used for sound output is ruled entirely by the particular phone app.
ADDJ69 said:
@uluruman
Hi! First of all sorry for my mechanic English hehehe.
I just broke my proximity sensor cause water... , Now im trying this method but I have a question.
Exist some way to put audio in the calls speaker ( the topside speaker used in calls)? For example, I want to listen some Whatsapp audio in private.
I want to put the smartphone on my ear and then automation change the speaker, besides turn off the screen.
I didn't saw any option, just the script option that I don't know how to use it and the "boardcast" option that i dont know how to use it neither.
Thanks in advance.
Click to expand...
Click to collapse
there was a app i think i saw on playstore. it wont automate it but u can switch entire audio output to ear piece. then u can revert it back lager manually