Hi all,
since I upgraded to android 2.2 I'm getting an annoying problem with the wifi of my desire. I got some place with wifi (802.11b/g home WPA1 PSK, office WPA2 enterprise TTLS), since I upgraded sometimes the phone doesn't see the wireless networks. Initialy I thought there was some problem/delay to switch from 3g network to wifi, but now I have done some tests and seem that the phone don't see any wifi network in these case! The only way to resolve the problem is to turn off the wifi and then on again. If I go to the network setting and I require a scan no network is avaible, nor using 3rd part programs like wifi scanners and similar.
Anyone is getting the same problem?
Thanks you in advance.
inode
I have had no problems at all since switching to 2.2 Have been all over - home, work, heathrow, Frankfurt and Austria turning WiFi and/or 3g on and off at varying times. Could you have a problem with a 3rd party app that has the ability / permission to turn WiFi on and off ?
Hope you manage to get it resolved - I'm loving Froyo.
PS - the wireless tendering turns the WiFi off, instead turning your device into an AP are you sure that isn't turning on?
siezear said:
I have had no problems at all since switching to 2.2 Have been all over - home, work, heathrow, Frankfurt and Austria turning WiFi and/or 3g on and off at varying times. Could you have a problem with a 3rd party app that has the ability / permission to turn WiFi on and off ?
Hope you manage to get it resolved - I'm loving Froyo.
PS - the wireless tendering turns the WiFi off, instead turning your device into an AP are you sure that isn't turning on?
Click to expand...
Click to collapse
No 3rd program switch wifi off, and all seem to be correct. I just rooted the phone and installed a mod and now all is working fine.
Thank you anyway
Have just purchased Motorola Defy.
Have no cellular signal at home. No problem, can run on wifi for internet and also use wifi for calling; Defy feature built in.
Cell standby draining battery excessively, ( 90-100% no signal)= ( 40-50% bat drain). If I use the airplane mode to stop cellular search can use wifi for internet but it disables the wifi calling feature ( known as UMA for blackberries).
Is there an app for the Motorola Defy that will disable cell searching for signal but allow both internet and calling wifi usage??
I am not computer programming savvy at all, you guys are the geniuses.
Love the phone hate this particular cell standby catch 22.
Thanks.
I haven't used this app before but I believe this is what you need, it called "Airplane Mode Wi-Fi Tool"
Here is the description of the app
This tool will help you manage your android phone to connect to Wifi networks (Wireless Internet, or Wi-fi) while on Airplane Mode.
This tool works with any version of Android, including 2.0+, however, it is only necessary if you have a device with Android 1.5-1.6. Android 2.0+ allows Wifi to be toggled while on AP Mode.
Airplane mode by default disables calling in/out, period
Thanks for your reply. I downloaded this app and it does enhance the Airplane mode capabilities but does not resolve the issue of being able to turn off cell standby while still being able to use both wifi internet and wifi calling.
Since I am not on a plane but am, instead, at home I believe what is needed is an app that directly addresses the cell standby searching issue and leaves the wifi settings to behave as intended; enabling the cell phone to fully function via wifi for both internet and calling when there is no cellular signal available, without a ridiculously and unnecessarily huge burden being put on the battery for a completely moot point...
If such an app does not exist then I believe there will be a demand for one and I ,for one, would be happy to donate for such an app.
Again, thank you for your reply.
mtoblr said:
Since I am not on a plane but am, instead, at home
Click to expand...
Click to collapse
I just installed the application to see how it works.
When you open the application for the first time there is an instruction how to use the app. Obviously, it was designed to work in real world when one is on airplane. However, if you keep scrolling down the instruction page and read the FAQ section (B) then it tells you how you can configure it to use your wireless settings instead.
I hope that solves your problem.
This is easy: *#*#4636#*#* Go into menu, turn Radio off (toggle ON/OFF in this hidden menu). With radio off both wifi and wifi calling stay active. (USA T-MO)
scrannel said:
This is easy: *#*#4636#*#* Go into menu, turn Radio off (toggle ON/OFF in this hidden menu). With radio off both wifi and wifi calling stay active. (USA T-MO)
Click to expand...
Click to collapse
I was aware of your solution before but I thought that would disable the wireless signal as well otherwise I would have mentioned it. I did a test while my wifi was on and disabled the radio option and the wireless stayed connected.
Thank you for your solution.
CSharpHeaven said:
I was aware of your solution before but I thought that would disable the wireless signal as well otherwise I would have mentioned it. I did a test while my wifi was on and disabled the radio option and the wireless stayed connected.
Thank you for your solution.
Click to expand...
Click to collapse
Right, but unlike airplane mode it does not shut down wifi calling. BTW, I do not understand the power drain issue. I leave my radio on while working all day, but using wifi with the wifi calling app set to wifi preferred and am seeing no heavy drain. Maybe -- under that same menu -- one should check to see that the "preferred network type is "GSM only." When wifi calling is disabled (even if wifi is active) the phone should default to GSM auto (PRL). I have noticed occasionally it will stay in GSM auto (PRL) with wifi calling on and that might cause a drain, but not sure.
Further to the discussions in this thread I just noticed after restarting my phone (off & on) the Mobile Data feature is enabled again.
There is another menu option called 'disable on boot'. Disabling data on boot did not work once I restarted my phone to test it but the menu showed the feature was still enabled unlike 'Disable Mobile Data'.
This is easy: *#*#4636#*#* Go into menu, turn Radio off (toggle ON/OFF in this hidden
Thank you very much for this info. I was unaware of the hidden menu and this does indeed solve my problem. I will also try the GSM only setting first with radio on to see if that resolves the drainage issue.
I'm completely new to android and this forum and think both are great.
Thanks again.
mtoblr said:
Thank you very much for this info. I was unaware of the hidden menu and this does indeed solve my problem. I will also try the GSM only setting first with radio on to see if that resolves the drainage issue.
I'm completely new to android and this forum and think both are great.
Thanks again.
Click to expand...
Click to collapse
"GSM only" should be the default when you are running wifi + wifi calling. Set your preferences in the wifi calling app to either wifi preferred or wifi only. Maybe that will stop your phone from searching for cell signals. However, if you kill the radio using the hidden menu it will for sure stop it from searching for a signal. So, if you are still getting drain, it's something else.
scrannel said:
This is easy: *#*#4636#*#* Go into menu, turn Radio off (toggle ON/OFF in this hidden menu). With radio off both wifi and wifi calling stay active. (USA T-MO)
Click to expand...
Click to collapse
Looks like with the new OTA update you can't do this anymore.
Hey All,
I just picked up my T-Mobile LG G3 last night and rooted it.
I am trying to use the tethering app like I did on the Nexus 5 but my other devices are not picking it up when I have it enabled on the new phone.
The app say's its enabled and shows the Name and passcode to join it, but again, no other devices that I was using before (ipad for example) see it when I scan for WiFi networks.
Can anyone please help? I use this app when at work and need to get it figured out and up and running again if possible.
Thank you,
Whiteice
Is the Wifi Tether Router app you're using by Fabio Grasso?
That's the one I was using on my Nexus 5 without any issues. I also just moved over to the Tmo G3 and can't seem to get any of my devices to pick up the SSID either. The developer says that it does work on the G3 and I also followed the settings laid out by the developer in his devices configuration page but still a no go. I emailed him to see if he may have some suggestions but no word yet. Hopefully he replies with something I/we can try to get this running. It was a great app on all my previous phones. I have faith in this developer, he seems to update his apps fairly regularly.
hoy128 said:
Is the Wifi Tether Router app you're using by Fabio Grasso?
That's the one I was using on my Nexus 5 without any issues. I also just moved over to the Tmo G3 and can't seem to get any of my devices to pick up the SSID either. The developer says that it does work on the G3 and I also followed the settings laid out by the developer in his devices configuration page but still a no go. I emailed him to see if he may have some suggestions but no word yet. Hopefully he replies with something I/we can try to get this running. It was a great app on all my previous phones. I have faith in this developer, he seems to update his apps fairly regularly.
Click to expand...
Click to collapse
Yes that is the same app I'm using.
I contacted him and he replied back asking Me to send a log file from within the app. I Did that this morning and waiting For further feedback. If I hear anything I Will report back here.
WhiteiceDMSTech said:
Yes that is the same app I'm using.
I contacted him and he replied back asking Me to send a log file from within the app. I Did that this morning and waiting For further feedback. If I hear anything I Will report back here.
Click to expand...
Click to collapse
I had the SAME problem with the app with my G3 and I've been back and forth with him via email. I had to try a few methods he gave me but the last one finally did the trick!
Here's his email that had the steps to get it to work below:
strange, yes other users use this app on G3
please try this config
Interface wlan0
Method 2
Channel 1
Encryption wpa2-psk
"No Firmware Reload" <- UNCHECKED
Let me know
Thanks
Fabio
Click to expand...
Click to collapse
It works now, because the settings on his site and his emails weren't working, but the above finally did it for me.
But I noticed the the DNS process, /system/bin/dnsmasq, was using on average 40% of my CPU constantly with the app enabled. So I checked the "Use Internal DHCP" in the DHCP settings and the process ended and the CPU use returned to normal.
I had asked in a reply if this app uses IP Tables to mask the hotspot use as mobile use or still shows up as Hotspot with T-Mobile. I wasn't sure if enabling or disabling the Internal DHCP would negate it or not, but he hasn't responded back yet.
Does anyone know if this app does mask it as mobile and not hotspot?
I just came off of Sprint to T-Mobile two days ago and I always used the native hotspot function on my rooted Note 3 that masked it as mobile use.
Hope it works for you guys as well.
JustLok said:
I had the SAME problem with the app with my G3 and I've been back and forth with him via email. I had to try a few methods he gave me but the last one finally did the trick!
Here's his email that had the steps to get it to work below:
It works now, because the settings on his site and his emails weren't working, but the above finally did it for me.
But I noticed the the DNS process, /system/bin/dnsmasq, was using on average 40% of my CPU constantly with the app enabled. So I checked the "Use Internal DHCP" in the DHCP settings and the process ended and the CPU use returned to normal.
I had asked in a reply if this app uses IP Tables to mask the hotspot use as mobile use or still shows up as Hotspot with T-Mobile. I wasn't sure if enabling or disabling the Internal DHCP would negate it or not, but he hasn't responded back yet.
Does anyone know if this app does mask it as mobile and not hotspot?
I just came off of Sprint to T-Mobile two days ago and I always used the native hotspot function on my rooted Note 3 that masked it as mobile use.
Hope it works for you guys as well.
Click to expand...
Click to collapse
Just tried those settings and so far it appears to be working.
Thanks you Fabio,
Whiteice
Darn, I wish it was working for me. I found that on Fabio's page and used those settings but they're still not working for me. Also tried to use the internal DHCP option but still no dice. I just sent Fabio my log file, hopefully he finds something that can get me up and running.
Woo hoo...I overlooked the method. Just confirmed the strings above works. Thanks all/Fabio!
JustLok said:
I had the SAME problem with the app with my G3 and I've been back and forth with him via email. I had to try a few methods he gave me but the last one finally did the trick!
Here's his email that had the steps to get it to work below:
It works now, because the settings on his site and his emails weren't working, but the above finally did it for me.
But I noticed the the DNS process, /system/bin/dnsmasq, was using on average 40% of my CPU constantly with the app enabled. So I checked the "Use Internal DHCP" in the DHCP settings and the process ended and the CPU use returned to normal.
I had asked in a reply if this app uses IP Tables to mask the hotspot use as mobile use or still shows up as Hotspot with T-Mobile. I wasn't sure if enabling or disabling the Internal DHCP would negate it or not, but he hasn't responded back yet.
Does anyone know if this app does mask it as mobile and not hotspot?
I just came off of Sprint to T-Mobile two days ago and I always used the native hotspot function on my rooted Note 3 that masked it as mobile use.
Hope it works for you guys as well.
Click to expand...
Click to collapse
I can confirm the above settings including the internal DHCP work perfect on my end also!
As a side note, it also appears that the data usage shows up on my T-Mo account as regular "Internet Access", not Hot Spot usage. Maybe I was looking at it wrong, or maybe my account hasn't fully updated yet, but it looks promising.
Thanks to JustLok for the tips!
Good to know it works. I tried it a few days ago and I didn't get any data, so I uninstalled it. Now that you guys confirm it's working, I might buy it.
I've been trying to get the stock tether to work. Found where to change the APN so that it doesn't use the pcweb one that tracks as hotspot, but I'm running into other issues, some other checks that need to be circumvented. This app is probably using the fast APN since pcweb is only listed deeply in the frameworks-res.apk of the G3 and those should never be used unless this app tries to tether as DUN (which I doubt).
Question, does this app have Tasker integration?
Just to clarify...'No firmware reload' should be checked or unchecked? Cheers!
wideasleep1 said:
Just to clarify...'No firmware reload' should be checked or unchecked? Cheers!
Click to expand...
Click to collapse
It would be unchecked, as listed in my post above in regards to the settings and tweaks to get it to work with D851 G3.
Also, been using it for days now and it does mask the tether use as mobile data and NOT as Hotspot data, as orbitalcomp confirmed, even using the internal DHCP server (which I was wondering if it would with the IP Table masking).
As for Tasker integration, I'm not sure what you mean havanahjoe with Tasker, as in the normal App Tasker or an app titled tasker?
I also noticed that my data connection just dies every so often, both on my G3 and my wife's G3. It show a connection with LTE and the data arrow up lit, but no data is moving. Even confirmed with the Internet Speed Meter Lite app that no data was being sent or received. I have to enable Airplane mode and then back off and the data connections becomes live again. I've read several reports of this on XDA too on Tmo G3's. This is either with the tether app or not, Tmo's data connection just stops working and needs to disconnect and reconnect to the tower/antenna to work again.
Finally, when using the widget for this tether app, when first tapping it (after a reboot or so), it does not enable it. You have to wait a little and then tap it again for it to enable. Once you get it to enable and become active, turning it on or off via the widget works on the first tap. It's just the first initial widget use upon a reboot that it takes two taps, about 5 secs apart to actually start up.
JustLok said:
It would be unchecked, as listed in my post above in regards to the settings and tweaks to get it to work with D851 G3.
Also, been using it for days now and it does mask the tether use as mobile data and NOT as Hotspot data, as orbitalcomp confirmed, even using the internal DHCP server (which I was wondering if it would with the IP Table masking).
As for Tasker integration, I'm not sure what you mean havanahjoe with Tasker, as in the normal App Tasker or an app titled tasker?
I also noticed that my data connection just dies every so often, both on my G3 and my wife's G3. It show a connection with LTE and the data arrow up lit, but no data is moving. Even confirmed with the Internet Speed Meter Lite app that no data was being sent or received. I have to enable Airplane mode and then back off and the data connections becomes live again. I've read several reports of this on XDA too on Tmo G3's. This is either with the tether app or not, Tmo's data connection just stops working and needs to disconnect and reconnect to the tower/antenna to work again.
Finally, when using the widget for this tether app, when first tapping it (after a reboot or so), it does not enable it. You have to wait a little and then tap it again for it to enable. Once you get it to enable and become active, turning it on or off via the widget works on the first tap. It's just the first initial widget use upon a reboot that it takes two taps, about 5 secs apart to actually start up.
Click to expand...
Click to collapse
Thanks for the update and confirmation of mobile vs. Hotspot..which meets my own experience. FWIW, your settings quote from Fabio simply says "No Firmware Reload" and doesn't state checked or unchecked...which is why I asked. At least I can't see it on Tapatalk. [emoji4]
Sent from my amazing LGG3!
JustLok said:
It would be unchecked, as listed in my post above in regards to the settings and tweaks to get it to work with D851 G3.
Also, been using it for days now and it does mask the tether use as mobile data and NOT as Hotspot data, as orbitalcomp confirmed, even using the internal DHCP server (which I was wondering if it would with the IP Table masking).
As for Tasker integration, I'm not sure what you mean havanahjoe with Tasker, as in the normal App Tasker or an app titled tasker?
I also noticed that my data connection just dies every so often, both on my G3 and my wife's G3. It show a connection with LTE and the data arrow up lit, but no data is moving. Even confirmed with the Internet Speed Meter Lite app that no data was being sent or received. I have to enable Airplane mode and then back off and the data connections becomes live again. I've read several reports of this on XDA too on Tmo G3's. This is either with the tether app or not, Tmo's data connection just stops working and needs to disconnect and reconnect to the tower/antenna to work again.
Finally, when using the widget for this tether app, when first tapping it (after a reboot or so), it does not enable it. You have to wait a little and then tap it again for it to enable. Once you get it to enable and become active, turning it on or off via the widget works on the first tap. It's just the first initial widget use upon a reboot that it takes two taps, about 5 secs apart to actually start up.
Click to expand...
Click to collapse
The hiding of the traffic is all about the APN. WiFi Tether Router uses the phone APN (fast.t-mobile.com) and the built-in hotspot uses pcweb.tmobile.com. That's why it's so easy to bypass, as long as WiFi Tether Router can do its thing by doing some iptables, dnsmasq and other Linux magic.
I have seen my LTE connection stop working from time to time. Not while tethering, but I rarely tether for more than 30 minutes at a time. Whenever I lose data, I just do the same, airplane mode on/off and it's back.
Tasker is an automation app. It's great for getting things done automatically. I use tethering in the car so that my dash mounted Nexus 7 can get internet. With Tasker, my hotspot is automatically turned on when I get in the car, and automatically turned off when I turn the car off. There is a method for applications to talk to each other in Android, these messages are called intents. With intents you can tell an app to shut down, to load a specific playlist (Spotify for example), or to enable/disable something. When using the stock Tether app, the system lets you toggle it with intents that Tasker already knows about. WiFi Tether Router has no intents, so there is no way to externally tell it to turn the hotspot on or off. The workaround is to emulate touching the enable/disable button (on the app or the widget). It's kludgy, but it works. It would be much cleaner and reliable if the dev enabled this functionality.
I tried the setting you suggested on the other thread, and by using Internal DHCP and not having WiFi Tether Router use DNSMasq to provide DHCP and DNS services, my battery drain is much more acceptable. I only lost 3% on my drive to work. I usually would lose 10% or more! This setting might be needed for other carriers where you do need to hide your data, but we don't have to worry about this with T-Mo.
havanahjoe said:
....
Tasker is an automation app. It's great for getting things done automatically. I use tethering in the car so that my dash mounted Nexus 7 can get internet. With Tasker, my hotspot is automatically turned on when I get in the car, and automatically turned off when I turn the car off. There is a method for applications to talk to each other in Android, these messages are called intents. With intents you can tell an app to shut down, to load a specific playlist (Spotify for example), or to enable/disable something. When using the stock Tether app, the system lets you toggle it with intents that Tasker already knows about. WiFi Tether Router has no intents, so there is no way to externally tell it to turn the hotspot on or off. The workaround is to emulate touching the enable/disable button (on the app or the widget). It's kludgy, but it works. It would be much cleaner and reliable if the dev enabled this functionality.
I tried the setting you suggested on the other thread, and by using Internal DHCP and not having WiFi Tether Router use DNSMasq to provide DHCP and DNS services, my battery drain is much more acceptable. I only lost 3% on my drive to work. I usually would lose 10% or more! This setting might be needed for other carriers where you do need to hide your data, but we don't have to worry about this with T-Mo.
Click to expand...
Click to collapse
Thanks for that explanation on Tasker, when I mentioned it to my wife last night, she said she was already using it on her old HTC One M7, so much for me being ahead of the curve. Or on the curve even, I guess. :cyclops:
I have noticed when using the Wifi Tether App, sometimes my laptop won't or can't connect to the hotspot after a while using it. I use it for extended periods of time at work, hours on end even, and my laptop will just disconnect from my SSID and won't connect, despite it being live. The SSID is seen and the laptop tries to connect but then just says it cannot do so.
I need to reboot my laptop for it to connect to it again. I'm not sure if it's the IP lease on my laptop expired or wasn't renewed with the tether app. Unfortunately, I cannot perform an IP renew or release in CMD on my laptop, because it's disconnected and needs a connection to do it! So I can't narrow the error to that function or not.
When I use the native Hotspot with TMo, I didn't have this problem last week when I was using it for three days before getting the Tether app.
Just some experience with it so far, in case anyone else was seeing the same or so.
How the heck did you all get this app to work? I cant change my apn settings to ipv4 like he says too. Data cuts off when I do
after update to lollipop not working
I was trying different settings,
After factory reset T-mobile hotspot is working, but when I tried to run "WiFi Tether Router" even t-mobile hotspot is not working...
Are you guys using d851 with lollipop?
Could somebody post for me correct settings?
Thx
clfuadam said:
I was trying different settings,
After factory reset T-mobile hotspot is working, but when I tried to run "WiFi Tether Router" even t-mobile hotspot is not working...
Are you guys using d851 with lollipop?
Could somebody post for me correct settings?
Thx
Click to expand...
Click to collapse
This app is broken in g2/g3 lollipop. It will also break built in tmo hotspot app as well and you would have to factory reset to get it working again. I switch back to kitkat just to use this app and also see no benefit in lollipop.. yet..
Can someone please help?
I can't get any of my computers to show the network name for WiFi tether router. I've never had this issue until today. My wife's phones doesn't have a problem, but mine won't show at all
I just switched to unlimited data on my LG G3 and got this app...
It works great with the G3 settings shown on the first page of this thread and on the app website. The speeds are the same on the device as on a client device so that's good...very fast LTE.
I originally tried setting the APN to LP4 (from default LP6) as the application directions stated must be done for T-Mobile but found that the network slowed (4G instead of LTE) and became somewhat unreliable. I'm wondering if this is even necessary on the G3 based on what I'm reading here. I switched the APN back to default.
My plan includes 5GB of tethering with unlimited on board so the problem is that how can I tell which data I'm using? My account page only shows unlimited it doesn't show how much of that is used for tethering even when I used the native tether app. I suppose I just have to try and go over and see what happens?
I've got this working on Cloudy 2.5 but the data is being counted as Hotspot data. Other than the settings earlier in the thread is there anything else I need to change so that it doesn't get counted as Hot Spot data?
TIA!
I am noticing an issue since I got the OTA upgrade to 6.0.1. My phone is having trouble connecting to my most used WiFi networks at work and at home. It will keep saying "connected, no internet" until I restart the phone and then it will fully connect. Anyone else have this problem?
I have a wifi problem since 6.0.1 update. if wifi settings are defined to never keep wifi while handset is sleeping, when I wake up the n5x, it is no longer able to connect to my home wifi. I have to disable and re enable wifi.
you should try to set wifi preferences to "always keep wifi".
Try setting your Wifi frequency band to either 2.4 or 5 GHZ and see if that helps.
Sent from my Nexus 5X using Tapatalk
Bousqi said:
I have a wifi problem since 6.0.1 update. if wifi settings are defined to never keep wifi while handset is sleeping, when I wake up the n5x, it is no longer able to connect to my home wifi. I have to disable and re enable wifi.
you should try to set wifi preferences to "always keep wifi".
Click to expand...
Click to collapse
More people with same problem here: http://forum.xda-developers.com/nexus-5x/help/6-0-1-wifi-sleep-issue-t3271788