after using it like one month before a week suddenly the phone didnt turn on , after too much pressing power button the phone start working but when turned the touchscreen didnt work after that i did force reboot by pressing power button from this its not turning on and the charging white blink also work when i put it on charger , any solution?
Best Regards
Related
Hi all,
My XDA IIs works well before. But few days ago the Power button doesnt work properly, it can turn on the phone, hold to turn off the back light, but I can't use it to turn my phone screen off like before. Anyone has same problem ?
Can you see any part of the screen? It might just be that the backlight adjustments are set too low when the unit isn't cradled. You might be able to see the screen in daylight.. or maybe it was inside your home. I forgot where I was at when it happened to me. In anycase, if you can see a bit of images on your screen, go into the Backlight properties and change the setting to your liking.
Good luck..
The problem is i can just press the power button to turn off my phone BEFORE (the screen is completly off), and NOW it doesnt work at all ! When my phone was off, I can press the Power button to turn it on, or when I hold it for few seconds the back light will be turned off, but press once to turn off. I dont know why, if somthing wrong with the Power button it should be doesnt work at all, that's mean i cannot turn on my phone as well. But other functions of the Power button are still work well, except the 'Turn off' :roll:
power off doesn't work anymore
I have the same problem here. I can't use the power button to power off my qtek 9090!!
i can use the power button to turn my pda on and to switch the background light on and off - so the "hardware side" of the power button is working.
however, i can't use the power button to turn off the device. it's very annoying, because i can't put it in my pocket after finishing a call :-(
this should be some sort of a software problem - so i hard resetted my device (a couple of times) - but that didn't help!
can anyone help?
thanks,
lorenz
the ba doesn't turn off it is always on staand by mode. ->settings -> system -> button lock
this will stop any missed call because when the ba is in standby the power button is the only one to work
power on is no problem. i can't put my BA into standby mode. if i press the power button while the BA is turned on, nothing will happen. the screen will stay on, the background light stays on.
i have no way to put it into stand-by with the power button!
try this and see if it works. it's a software app that wil rest, shut down, and turn the screen off. just copy it to your BA temp directory and install it.
power button problem
nemchua
Is your problem solved ?
Because I have the same problem.
Power of switch doesn't work !!!
Any help would be welcome.
power button problem
Does anyone solve the problem???
Had the same problem...
I had the same problem going on for about two weeks or so...never changed anything and it went away all by itself.
The problem has not come back now in over 4 months.
Sure would love to know what the problem was tho...
Greetings,
Noddy
Power Off does not work
Add my name to people with this problem.
The only event I can link it to is this: I deleted my Motorola Bluetooth headset and installed a Logitech headset. I noticed the problem (can't turn OFF with POWER BUTTON) soon after that.
same problem for me ..... someone must know !!!!
I think it is a hardware problem. The contact is not making cleanly. Disassemble and spray time, perhaps.
It's a standard push switch, easy enough to replace, I occasionally list themon ebay but any phone repairier should have them in stock.
Richard
i had same problem yesterday afternoon, but it is ok now. recovered by himself
Write again in two weeks and let us know if it is still healthy. In my case, anintermittent problem became continuous.
Can't turn the screen on after pressing power button
I have a problem with my Bell Atrix. After pressing power button to lock the screen, i can't wake up the screen up by pressing that button again. Could anyone tell me how to fix it pls.
Hi all,
does anyone sometimes have to press the power button (when phone is completely turned off) twice (2 presses to turn on) sometimes?...
so just to confirm
- handset is off
- push power button once (sometimes doesnt come on
- push for second time (and powers up)
im defiantly pushing for long enough
iv have no issues with the button at all when in the UI or when locking/unlocking display
iv done a few tests where i have turned off. then went to switch on, with the same pressure and sometimes it starts with one, sometimes it starts with two presses,
do u think this is a fault? anyone experience this? normal?
just checking...
thanks heaps!
I had the opposite on my first one. When I pressed the power button to turn screen off, the screen went black for 1 sec and jumped back on lock screen.
brodiecb said:
Hi all,
does anyone sometimes have to press the power button (when phone is completely turned off) twice (2 presses to turn on) sometimes?...
so just to confirm
- handset is off
- push power button once (sometimes doesnt come on
- push for second time (and powers up)
im defiantly pushing for long enough
iv have no issues with the button at all when in the UI or when locking/unlocking display
iv done a few tests where i have turned off. then went to switch on, with the same pressure and sometimes it starts with one, sometimes it starts with two presses,
do u think this is a fault? anyone experience this? normal?
just checking...
thanks heaps!
Click to expand...
Click to collapse
to switch on device you have to keep pressed power button for few seconds or u can keep it pressed until you see lights at the touch keys.. :good:
Hi
brodiecb said:
Hi all,
does anyone sometimes have to press the power button (when phone is completely turned off) twice (2 presses to turn on) sometimes?...
so just to confirm
- handset is off
- push power button once (sometimes doesnt come on
- push for second time (and powers up)
im defiantly pushing for long enough
iv have no issues with the button at all when in the UI or when locking/unlocking display
iv done a few tests where i have turned off. then went to switch on, with the same pressure and sometimes it starts with one, sometimes it starts with two presses,
do u think this is a fault? anyone experience this? normal?
just checking...
thanks heaps!
Click to expand...
Click to collapse
I don't think many people would turn their phone completely off so haven't found the issue.
When you power off what will be happening is the phone is off as much as it can be, but these buttons are soft off, the battery is still connected and some power must be drawn to run the power circuitry to detect the button being pressed again to signal to power back up the phone, in the same way when you turn your TV off by the remote, power is still drawn to run the remote sensor on the TV.
To keep the drain on the battery as low as possible so the battery isn't completely discharged over months of storage I suspect the power chip waiting for the on signal again is only sampling every so often to save power so it can be in super deep sleep state. This means depending on where in this cycle you are when you press the power button it might seem like it isn't responding, so typically you have to leave it depressed long enough for it to be "seen".
The better option is to just to put your phone into flight mode if you don't want to be disturbed or want the phone off. I do this overnight and lose no battery power by the morning, so it is as good as off. You can add a button to your home screen to do this quickly, widgets are included already for that.
Regards
Phil
Mine does the same thing.. Sometimes it does it with waking up from sleep also.
Sent from my HTC One X using xda app-developers app
Hi,
my Hox's screen doesn't turn on after I put it to sleep. I press the power button and only capacitive buttons turn on and after a few seconds they turn off too. And when I press the volume keys and it changes the volume.
Then I hold power button for long time and phone Turns off . when I turn it on it boots with screen still off.
After a few times turning the screen on/off ,it turns on and its fully functional, I can turn it off, wait a few seconds , and turn it on again.
but after waiting for a minute I have the same issue.
This issue happened when I flashed my first rom(ARHD) on it. I have tried re installing ARHD, and recovering stock rom, but the problem is still there.
Can somebody help me please ?
My SW3 appears to have died this morning. I unplugged it from the charger, put it on my wrist and pressed the power button to turn it on. I felt it vibrate to say it was on, but then later noticed that the screen was blank. I tried holding the power button to force a reset but nothing happened.
Before I send it off to Sony, does anyone know if there is a reset button anywhere or anything else I should try to get it to turn on?
bigdave196 said:
My SW3 appears to have died this morning. I unplugged it from the charger, put it on my wrist and pressed the power button to turn it on. I felt it vibrate to say it was on, but then later noticed that the screen was blank. I tried holding the power button to force a reset but nothing happened.
Before I send it off to Sony, does anyone know if there is a reset button anywhere or anything else I should try to get it to turn on?
Click to expand...
Click to collapse
It once happened to me.
According to this site, to reset our SW3's we need to hold our power keys until the watch vibrates one time and restarts itself. But it didn't help me so there's another thing - to force the shutdown. Press power button until it vibrates three times, then turn it back on.
In my case, the watch started working as it should and such thing never occurred again.
romcio47 said:
It once happened to me.
According to this site, to reset our SW3's we need to hold our power keys until the watch vibrates one time and restarts itself. But it didn't help me so there's another thing - to force the shutdown. Press power button until it vibrates three times, then turn it back on.
In my case, the watch started working as it should and such thing never occurred again.
Click to expand...
Click to collapse
Thanks, I'd tried holding the power button but it wasn't doing anything. It actually turned back on last night, complained that the battery was flat and turned itself off again. Plugged it back in to charge and it's working again this morning. Although my Pujie Black watch face isn't updating as it should and I'm not getting notifications like I should either.
Think I'll give it a factory reset just to be safe.
Aaaaand won't turn on again this morning. Been holding the power button for ages, does nothing, won't connect to Xperia Companion for a reset neither.
Background -
I bought this OnePlus 5T with a smashed screen to fix.
Paid 70 bucks for it plus the screen is just shy of 150 in total.
I was able to replace the screen and frame which was a little more complicated than I anticipated, but it ended well and the phone seems fine, although the screen quality isn't as good as stock.
***Problem - it seems that for unknown reasons, after turning off the screen pressing using the power button, screen becomes black and won't turn on, not until i hold the power button for ten seconds and restart the phone the hard way. Then the phone turns on and starts working again, but if I turn the phone off with the power button then it won't turn on again. I can tell the phone is working behind the black screen, vibration working, notification light working. But Everytime I turn the phone off with the power button I have to hard reboot the phone to get it back on again. Once this starts happening I have to factory reset to get the power button functioning normally again. It will work normally for a day or two and then out of no where the issue comes back again after pressing the power button - screen won't turn on.
Could it be software? I know it might be natural to suspect the screen is faulty, but the screen works normally until I use the power button to turn it off, and then works normally again for a couple of days after a factory reset ...
Thoughts ?