Develop Bugs

Screen vibration after flasshing the rom

Hi everyone.
I have a big issue with my phone. I decided to upgrade the rom by an official one (french HTC rom). I use the unsigned hard SPL and flash it. Since that, my screen is vibrating. I don't know what is the probleme (maybe the phone was too hot during flash and something burn inside ?).
I tried a hard reset => nothing best.
I'm a little big afraid :-( Anyone got an idea ?
Thanks a lot.

I think this is normal my Diamond vibrate on every Startup and when I inital an Call.
Ghostrider

No actually it's not the phone's vibration. It's the image on the screen witch is "flashing" and vibrating.
After a sleeping time, the vibrations are less visible.

If the image on the screen becomes "fuzzy" (like TV interference), it almost sounds like faulty screen some people were experiencing. I doubt it have to do something with your flashing, just happened coincidentially at same time.

nael33 said:
Hi everyone.
I have a big issue with my phone. I decided to upgrade the rom by an official one (french HTC rom). I use the unsigned hard SPL and flash it. Since that, my screen is vibrating. I don't know what is the probleme (maybe the phone was too hot during flash and something burn inside ?).
I tried a hard reset => nothing best.
I'm a little big afraid :-( Anyone got an idea ?
Thanks a lot.
Click to expand...
Click to collapse
Hi, i did have the same problem using TLR (cant remember what version).
What i did was to flash it again with another ROM (bElite v0.54) and my picture was fine after that

Ive got that problem when I flash ANY rom with HARD-SPL running so what I do is flash back to a stock version of spl (1.37) from here http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39
So in this order......
1 - Flash HARD SPL
2 - Flash rom
3 - Flash Stock SPL
Problem solved

nael33 said:
I'm a little big afraid :-( Anyone got an idea ?
Thanks a lot.
Click to expand...
Click to collapse
Try what ratcom said. If it still flashes with standard ROM, I would advise you to make everything original again (ie original ROM & SPL) then send back to HTC for repair.

Hi. After my issue, I decided to downgrade the phone and, when I put the official SPL, it was working. 5 minutes later, I read ratcom's post that confirm the problem and the solution. So, this morning, after charging the battery, I used unsigned SSPL, put the HTC rom, get one more time the sreen issue, and reflash the SPL by an original one just like ratcom said. And ... it's working. No more sreen vibration ! And a new and nice HTC rom !
So, thanks for your help !

Help - my Diamond can't boot

Hi,
I have my Diamond over a year and all was great till one day, suddenly it can't load the OS.
After power on, the black screen with "TOUCH Diamond" appear,
then it shows the radio version in red at the right bottom of the screen and from there nothing happen.
I tried to flash several ROMs & Radios, including the original ROM from HTC site but nothing.
The process of flashing seems to be fine and in fill all the 100% bar,
then it restart like during regular ROM flashing procedure but still no boot.
I tried to flash other hard-spl and still nothing.
I'm really lost and I hope someone has an idea for a solution.
Thanks
sorry if it's not the right place for this topic,
I also put it on general Diamond post so this one can be deleted.

MTTY?
Have You tried MTTY utility. Maybe it could help you.
Manual:
http://forum.xda-developers.com/showthread.php?t=540290

[Q] [HELP] Touch Screen Calibration

Hi guys,
first of all... I want to thank everybody who clicked on my thread and tried help me... ... to the point....
I bought WFS with borken digitizer, then went on MR. Eba and bought another one. And here comes first question... was there a Rev.2 or Rev.3 digitizer ? Wasnt sure so picked Rev. 3 ... Disassembled phone a and assembled back with new digitizer... phone start and woalla... touch doesent respond to anything... i knew that it have to be calibrated so maked goldcard, and booted to Hboot... calibration script loaded... everything went fine until it got to DIAG .... blue header with "TP Calibration" appeard... and then... the wild error attacked... red colored "Step 1 NG" and phone hang... tried to run it through night but battery drained... :/
So... I need to get new touchscreen or another goldcard ... or what ? ... and please someone atleast tell me what Step 1 NG means...
Thanks for any suggestions
Best Regards, Peter
P.S.: Sorry for my English... Im from Slovakia... (nobody knows where it is som round it... its in EU ... LOL )

Touchscreen dead

Hi,
a friend of mine replaced the screen of his Ace 2 because it had a crack. After that, the phone didn't boot up anymore (stuck at the "Galaxy Ace 2" screen). I flashed a 3 part firmware via odin, now the phone starts but the touchscreen doesn't work. I tried flashing various other FWs but still no change and I also checked the display again.
Now I don't know if the display is defect or something went wrong while flashing.
Can someone tell me what to do now?
Thanks a lot
Thomas

[Q] "Lock Screen" not respond, Until Hard reset

I've searched for this issue for a while but nothing comes up. If i missed it or this post is redundant . I apologize in advance.
Last week, My Sony xperia Z1c screen broke ,so i changed a new one. After that a few hour, I locked phone and when i wake it up, Touch screen wasn't respond. I mean phone is still functional ,you can see new notification coming up, but can't touch anything. Until I hard reset my phone, it was back to normal, touch screen is working, JUST FOR A WHILE. And this issue keep coming back.
I went back to a shop that changed my broken screen in the first place. They changes a new screen for me again, But the issue was still there.
I've no idea what's happens to my phone. Does anybody having a same issue? Please Help me.

Did you try to flash other firmware and check if this still persist?

Madtung said:
I've no idea what's happens to my phone. Does anybody having a same issue? Please Help me.
Click to expand...
Click to collapse
perhaps there needs to be a calibration process after the screen has been installed.
If it were my phone I would try and flash with the latest firmware for your area/provider.
I would recommend IaguCool's thread on Xperia Firmware Downloader & Checker, if you have flashtool installed you can make your own ftf that is exactly right for your phone.