got to the Odin box. checked PDA. clicked PDA.
The following comes up next to PDA: C:\Users\Debbie\Downloads\GT-I9190 (2)\GT-I9190\CF-Auto-Root.tar
click the start button at the bottom of the Odin screen.
Phone screen sys downloading do not turn off target. Blue line doesn't move past about 1/4 the way across screen.
Not sure if it matters, but phone screen upper left corner: one line says Knox Kernel lock: 0x0 then Knox warranty void: 0x0
after a couple minutes Odin screen says Failed.
Message box:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I think the phone may be hung. Don't know what to do to reset without causing bigger issues. Beginner with all this. Please help me.
Oh, I did try to just open the CF-auto-root file to see if I was missing something, but it wants a password to open the file.
Hi,
I will have your thread moved to your device section.
Good luck!
Related
I recently found out I soft bricked my phone after browsing through the forums. I looked up for the solution and it turns out that I need to reset it back, no problem with that so I installed odin back again (I rooted my phone before so I had it). I first downloaded the official firmware from sammobile or some site like that and I downloaded a PIT file for my phone because the tutorial said it was essential when resetting a smartphone. I followed every step but when I launch odin and select the required tick boxes and the PDA PITi I start it. It starts up but in the middle of the loading I shows up the DO NOT TURN OFF THE TARGET!!! message and It stops.
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This is the error and I can't seem tı get past it. I really need to deal with this quickly so if any of you have a solution, ı would appreciate it. Thanks
Anyone has the same issue? I need to fix this ASAP.
a
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
Now the error goes like this and nothing more.
aqertmen said:
Anyone has the same issue? I need to fix this ASAP.
Click to expand...
Click to collapse
I'm getting the exact same problem, can't fix it
Have you made any progress?
Thanks.
aqertmen said:
I recently found out I soft bricked my phone after browsing through the forums. I looked up for the solution and it turns out that I need to reset it back, no problem with that so I installed odin back again (I rooted my phone before so I had it). I first downloaded the official firmware from sammobile or some site like that and I downloaded a PIT file for my phone because the tutorial said it was essential when resetting a smartphone. I followed every step but when I launch odin and select the required tick boxes and the PDA PITi I start it. It starts up but in the middle of the loading I shows up the DO NOT TURN OFF THE TARGET!!! message and It stops.
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This is the error and I can't seem tı get past it. I really need to deal with this quickly so if any of you have a solution, ı would appreciate it. Thanks
Click to expand...
Click to collapse
doc1975 said:
I'm getting the exact same problem, can't fix it
Have you made any progress?
Thanks.
Click to expand...
Click to collapse
Hi
Do you have a custom recovery?
Which phonemodel do you have?
U can install TWRP through Odin using a tar file. Go to TWRP and search your model, get the tar file and install it.
From TWRP u can sideload a rom using ADB.
You can push files to the phone using it, that way u can push the rom to the phone and install it through TWRP.
A long way around but worth trying when all else fail.
I was trying to recover my Samsung Galaxy note 2 from soft brick status. so I tried to install new CWM recovery mode. it looks like something happened in the middle of the installation and now I started to get pit related errors in oden and the screen turned blank white when turning ON my phone.
I read in some places that I need to use new pit file to re-partition my phone. however I tried to download countless pit files from the net but none of them worked even the one I found here http://forum.xda-developers.com/showpost.php?p=31801134&postcount=4
I'm getting the same error as oden log below:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
can anyone help me please.
No reply
It looks like this is the least interesting question in the whole community, after it has been posted for more than 4 days and seen by more than 120 people no one has ever replied!!
Please guys, if you have any suggestion, Kindly dly share it.
I am not new to the rooting scene, however I have a problem that I can't seem to figure out. I've been reading now for the past 2 days, tried several things and still can't get this resolved. I've never had any issues in the past with odin and rooting samsung phones before, including ones with locked bootloaders. However, I've met my match. I tried following the tutorial listed on this site for rooting the samsung note 3 from tmobile. I watched the video and followed along with the files listed here
http://forum.xda-developers.com/note-3-tmobile/#root
My problem is as follows: I tried rooting with odin, installed kies for the usb support but halfway through the root process I get the big RED FAILED! phone's progress bar stops and it hangs. I though this was strange and never encountered this before. I then tried repeating the same process and same results, however this time around I am only able to bring the phone into "odin" mode "download" and not the original stock rom.
At first I was getting the original "the firmware encountered an upgrade issue" and couldn't bypass this unless I opted for download mode. I've tried the same steps to "unbrick" via oden with stock tmobile firmware for this phone and yet it yields the same results, big exclamation failed on odin. I then tried the process with the .pit file to partition that I found online somewhere and that fails too. My note starts up now, but stuck at the samsung galaxy note 3 screen. I've tried several versions of odin, switching usb cables, usb ports and I am unable to root this phone or even get it unbricked! i've read extensively here and can't seem to find a solution to my problem. Can someone PLEASE point me in the right directions?? BTW, I am using a mac with VMWARE, i've never encountered any issues with vmware in the past while running windows 8.
Phone says the following:
Once in download mode my phone says the following:
ODIN MODE
PRODUCT NAME: SW-N900T
CURRENT BINARY: CUSTOM
SYSTEM STATUS: OFFICIAL
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X0
QUALCOM SECUREBOOT: ENAMBLE
RP SWREV: S2, T2, A2, A3 P2
WRITE PROTECTION: ENABLE
UOC START
and I get these results from ODIN:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900TUVUCNB4_N900TTMBCNB4_N900TUVUCNB4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please someone help me, I am desperate and I can't think of what to do next.
http://forum.xda-developers.com/showthread.php?t=2677032
TWEAKED N3
BACARDILIMON said:
http://forum.xda-developers.com/showthread.php?t=2677032
TWEAKED N3
Click to expand...
Click to collapse
I can't seem to do this on 2 versions of windows installed on vmware for my mac. Everytime I try odin fails! Is there a way you can help me do this with heimdall on my mac?
Hi, I am not sure if I am posting at the proper forum but I know all the capable developers are here and I hope someone can help me. Please let me know if it is not. I tried to root my tab pro 8.4 with the original firmware by following a guide I found online using Odin to do the updating. Everything step seemed to be working but the tablet did not reboot and not it is stucked at the 'Downloading... Do not turn off traget!!' screen. On Odin side, it said "Pass" on top. I waited for a while but it did not reboot. After some research online, I tried to hold down the power key for a few seconds and the screen turned black and the the same 'Downloading...' screen came back. I tried holding down the power, up volume and home keys but got the same results everytime. Would anyone have any idea what had went wrong and how I can get my tablet working again? On the 'Downloading...' screen, it is showing the following at the top left hand corner:
Could not do normal boot.
ODIN MODE
PRODUCT NAME: SM-T320
CURRENT BINARY: Custom
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
QUALCOMM SECUREBOOT: ENABLE (CSB)
AP SWREV: S1,T1, R1, A1, P1
WRITE PROTECTION: Enable
UDC START
Thanks in advance.
ernsterw said:
Hi, I am not sure if I am posting at the proper forum but I know all the capable developers are here and I hope someone can help me. Please let me know if it is not. I tried to root my tab pro 8.4 with the original firmware by following a guide I found online using Odin to do the updating. Everything step seemed to be working but the tablet did not reboot and not it is stucked at the 'Downloading... Do not turn off traget!!' screen. On Odin side, it said "Pass" on top. I waited for a while but it did not reboot. After some research online, I tried to hold down the power key for a few seconds and the screen turned black and the the same 'Downloading...' screen came back. I tried holding down the power, up volume and home keys but got the same results everytime. Would anyone have any idea what had went wrong and how I can get my tablet working again? On the 'Downloading...' screen, it is showing the following at the top left hand corner:
Could not do normal boot.
ODIN MODE
PRODUCT NAME: SM-T320
CURRENT BINARY: Custom
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
QUALCOMM SECUREBOOT: ENABLE (CSB)
AP SWREV: S1,T1, R1, A1, P1
WRITE PROTECTION: Enable
UDC START
Thanks in advance.
Click to expand...
Click to collapse
What root method are you using? Try again this time make sure auto reboot is selected in odin.
Or... Force a reboot by holding Power, vol up and down, and home buttons for about 10 seconds and it should reboot. Or just tick auto reboot in odin
Airtioteclint said:
What root method are you using? Try again this time make sure auto reboot is selected in odin.
Click to expand...
Click to collapse
I followed blog.flexispy.com/root-galaxy-tab-pro-8-4/ and used CF-Auto-Root-mondrianlte-mondrianltexx-smt325.tar.md5. The auto reboot box and F. ResetTtime box were automatically selected when I started Odin3 v3.09. No other boxes were checked. The following is the listing under the message box:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-mondrianlte-mondrianltexx-smt325.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img.ext4
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I got the big green PASS! at the top. When the tabpro tried to reboot, it showed 'Could not do normal boot' and 'ODIN MODE' in red' along with some other information as what I have listed on my original post and just stay on that 'Downloading...' screen.
Thanks!
ernsterw said:
I followed blog.flexispy.com/root-galaxy-tab-pro-8-4/ and used CF-Auto-Root-mondrianlte-mondrianltexx-smt325.tar.md5. The auto reboot box and F. ResetTtime box were automatically selected when I started Odin3 v3.09. No other boxes were checked. The following is the listing under the message box:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-mondrianlte-mondrianltexx-smt325.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img.ext4
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I got the big green PASS! at the top. When the tabpro tried to reboot, it showed 'Could not do normal boot' and 'ODIN MODE' in red' along with some other information as what I have listed on my original post and just stay on that 'Downloading...' screen.
Thanks!
Click to expand...
Click to collapse
Ooh, I think you flashed the wrong model. There's no telling what dsmaged has been done. You have the wifi model or the lte?? Here's the wifi model link http://download.chainfire.eu/383/CF...ifi-mondrianwifixx-smt320.zip?retrieve_file=1
Oh no! That's bad! So what can I do now?
ernsterw said:
Oh no! That's bad! So what can I do now?
Click to expand...
Click to collapse
Try Flashing the stock firmware in odin. Because you are still able to get into download mode hopefully that's a good sign. Just to be sure you have the wifi model correct? Get the full firmware here
http://forum.xda-developers.com/gal...320xar1ank1-extracted-stock-firmware-t2954549
My tabpro is the 8.4 wifi version. Should I even bother to try flashing the correct firmware to see if it works first or just go with the stock firmware? Thanks for you help!
I flashed the stock firmware and everything got back to how it was before. I was then able to root the device with the correct link you provided. Thanks very much for you help!!
Hi everyone!
Left phone on charge, when came back few hours there was just initial Samsung logo with model number on screen (the one right after you switch your phone on). So no flashing or doing anything naughty, just phone left to charge in a good state.
I had latest CM installed.
Obviously can not go into recovery, or flash anything in boot loader (ctrl+vol. down+power). Odin returns "no PIT partition". Googled for solution, but only found dead links. As far as I understand I need a factory image and PIT partition file (at least?).
Can someone point me in the right direction?
Thank you,
xy
xywojtek said:
Can someone point me in the right direction?
Click to expand...
Click to collapse
HERE
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
:crying:
Thank you for the file anyway