Trying to figure this out. Browsed forums for the last 24 hours, unable to come up with a way to figure it out. I was running Effortless rom, and older version that I can't remember, but it was on NF6 firmware. I wanted to play around with cm11 so I decided to flash back to stock NF6 then update to NF9 for the VOLTE update just to have it. So I triangled away, wiped then rooted and installed TWRP via ODIN, made a backup, everything went fine. Then I downloaded cm11 and gapps 4.4.4 and put them on my internal sd and went to flash in TWRP but cm11 was giving me errors. I figured it may have been TWRP so i decided to flash CWM but no go. It wouldn't stick. Tried again, no luck. Downloaded ROM Manager and this time I installed CWM through there. Tried rebooting in to recovery and ended up getting stuck in the "recovery booting" bootloop, so I flashed stock NF9(since I was on this firmware now) and tried installing CWM again, no luck. When I tried booting to recovery, it was stock NB4 recovery. I'm thinking that I'm stuck on an old bootloader and the recovery isn't NF9, which is the current stock recovery. I'm thinking that the reason why I'm unable to flash anything in TWRP/unable to install CWM at all is because of the stock recovery and possibly bootloader being NB4 for some reason while my baseband and build are both NF9. Any ideas/help would be appreciated. Thanks guys.
re: custom recovery
pyr0path said:
Trying to figure this out. Browsed forums for the last 24 hours, unable to come up with a way to figure it out. I was running Effortless rom, and older version that I can't remember, but it was on NF6 firmware. I wanted to play around with cm11 so I decided to flash back to stock NF6 then update to NF9 for the VOLTE update just to have it. So I triangled away, wiped then rooted and installed TWRP via ODIN, made a backup, everything went fine. Then I downloaded cm11 and gapps 4.4.4 and put them on my internal sd and went to flash in TWRP but cm11 was giving me errors. I figured it may have been TWRP so i decided to flash CWM but no go. It wouldn't stick. Tried again, no luck. Downloaded ROM Manager and this time I installed CWM through there. Tried rebooting in to recovery and ended up getting stuck in the "recovery booting" bootloop, so I flashed stock NF9(since I was on this firmware now) and tried installing CWM again, no luck. When I tried booting to recovery, it was stock NB4 recovery. I'm thinking that I'm stuck on an old bootloader and the recovery isn't NF9, which is the current stock recovery. I'm thinking that the reason why I'm unable to flash anything in TWRP/unable to install CWM at all is because of the stock recovery and possibly bootloader being NB4 for some reason while my baseband and build are both NF9. Any ideas/help would be appreciated. Thanks guys.
Click to expand...
Click to collapse
If I were you the first thing I would do is to ODIN flash TWRP recovery
and go from there.
Here is a direct download link for the latest odin flash twrp
custom recovery for the N900T Note 3:
https://app.box.com/AndroidShare
Once you get into twrp recovery do a complete wipe
which includes wipe data, system, cache, dalvik and
last but not least do a factory reset in twrp.
When that's done odin flash the official stock N900T NF9
firmware which can be found at http://SamMobile.com
After that's done you will need to odin flash cf-autoroot
and then odin flash twrp recovery again.
Here is the download link for cf-autoroot:
https://app.box.com/s/rgovggya5gkc51lc1uax
Then simply copy your favorite N900T zip file rom into
your internal sd and flash the N900T rom of your choice.
Be sure to do a full and complete wipe again before
flashing any custom roms.
Good luck!
Related
I just accepted the cyanogen 10 snapshot update today for my d2spr; after the update finished it left me stuck in a bootloop, and Im unable to access recovery! I want to go back to the rom I was at before the update, which was the cm-10.1.3. Please help!!
Download mode and flash a custom recovery tar
CNexus said:
Download mode and flash a custom recovery tar
Click to expand...
Click to collapse
Thanks for the reply, I just downloaded a stock rom from samsung, and flashed via odin. It was successful, however even with the stock rom, I am still stuck in a boot load, and it still wont let me into recovery mode....
Solved!!
So I finally solved the issue. After I had flashed the stock rom via odin, I needed to find away to wipe cache's and do a factory reset. I finally accomplished this by downloading the .pit file, and re-flashing it together with the stock rom all through odin. After doing so, I was finally able to get into recovery, wipe, and do a factory reset. For anyone else having this issue, here is a link where I found the .pit file, and a thread with some basic instructions:
:laugh:
PIT Files: http://d2tehp.chickenkiller.com:22222/pits/
Basic Instructions: http://teamuscellular.com/Forum/topic/3882-pit-files-for-all-us-variants-of-sgsiii/
Hi! I have encountered a problem, and really hope someone can help me!
Two days ago i flashed Omnirom Nightly on my n7105 to get Android 4.4. I was running cmw recovery but couldnt get the ota updates to work, so i was trying to flash open recovery instead. I used an apk that was supposed to install a script.
When i rebootet my phone, all i could get was the Note 2 boot image. It wont boot into recovery mode, or the rom. I am however able to boot into download mode.
Custom Binary download: Yes (4 counts).
Current binary: Custom
System Status: Custom.
How should i proceed? I've already tried to reflash cwm recovery, which did work, but didnt solve the problem. I am currently downloading stock firmware, but the file is 1.2 GB so it will take i while. Figured i should ask here in the meanwhile.
I'm not an expert at Android at all, im just a guy enjoying having custom roms and playing around a little. I do know that there are a lot of very talented people in this forum, and i really hope someone can help me find a solution. I've been googling for hours, but cant find anything that seems to work for me / or i dont fully understand and wont risk try before someone approves it.
Thank you, Vetle
EDIT: Is it correct that i cant flash any custom rom trough Odin? Or could i just flash omnirom again trough Odin?
If i manage to flash the stock rom and the bootloop goes away, will everything go back to normal, so i can flash cmw again and then a custom rom again?
No custom rom can be flashed through odin, as most of them are zip cwm/twrp base.
When u can only go to download mode, an official firmware only can help u through odin.
Sent from SM-N9005 with xda-app
Thanks for the answer!
Yup, i have flashed a stock rom now and i got the stock recovery. Everything was working fine.
Then i proceeded to do a factory reset in the stock recovery and flashed cwm trough Odin. When it was done, it wouldnt let me into recovery again! I can still boot up the phone tough.
I've also tried Open recovery. CWM via Rom manager. Open Recovery trough Goo Manager... Still cant get recovery to work, the stock rom works tough.
Any ideas?
Okay, i tried to flash the stock rom again and installed Rom Manger.
It still showes TWRP and CWM under installed recovery and i guess these its these two who makes the problem.
My plan now is to figure out how to completely remove them. I've never done anything related to adb before, so i hope it possible to remove them in another way?
This is so weird. Somehow i managed to install CWM Touch via Rom Manager and it booted. When i choose reboot /pull battery it will only boot straight into CWM again. I tried to flash TWRP via Odin, wich sucseeds, but then it reboots into CWM again!
I am soo lost its almost funny!
EDIT: Since i could get into cwm now, i tried to flash omnirom, but it aborts and all i get is status 7...?
EDIT2: Latest now is that i suddenly managed to install TWRP via Odin, but i still cant install the latest omnirom, all it says is "updating partition details".
vetle666 said:
This is so weird. Somehow i managed to install CWM Touch via Rom Manager and it booted. When i choose reboot /pull battery it will only boot straight into CWM again. I tried to flash TWRP via Odin, wich sucseeds, but then it reboots into CWM again!
I am soo lost its almost funny!
EDIT: Since i could get into cwm now, i tried to flash omnirom, but it aborts and all i get is status 7...?
EDIT2: Latest now is that i suddenly managed to install TWRP via Odin, but i still cant install the latest omnirom, all it says is "updating partition details".
Click to expand...
Click to collapse
I had recovery problems in the last few days also.
Installed DN3 rom using philz recovery, because its capable of prepare the phone to a new rom in a easy way.
It all went fine until first reboot.
I had a recovery boot loop. All I could see were some buttons and then reboot again.
Like you I had download access and flashed philz with Odin, but no luck.
Installed twrp via Odin and all was fine, and flashed philz new version.
Then I had to flash a new kernel (to be able to access wifi) and it all started again. Now I'm back on twrp.
Let's see what happens on my next flash.
My suggestion is to flash the recovery, and if that's OK flash the rom and use it
Next time you need recovery get Odin to help, but not all the way from an original rom. Just the custom recovery.
But if you want to get rid of your strange recovery configuration, and you are not already on new 4.3 recovery(which in your case could explain some of the problems you had) , with knox, install an older original rom, 4.1, and make all the steps, root it, install a custom recovery, and from there the room you want.
Reading your path sorting this problem, that was what would do next
Best regards
I tried to unroot my phone after getting stuck in a cyanogen bootloop a while back. I managed to get into recovery and install stock firmware via Odin. I did not however install the stock kernel or stock recovery. I am now in a stock t-mobile bootloop. I'm not sure what to do, I have been unable to get into recovery thus far, but I can keep trying. What can I do?
lasabrjotur said:
I tried to unroot my phone after getting stuck in a cyanogen bootloop a while back. I managed to get into recovery and install stock firmware via Odin. I did not however install the stock kernel or stock recovery. I am now in a stock t-mobile bootloop. I'm not sure what to do, I have been unable to get into recovery thus far, but I can keep trying. What can I do?
Click to expand...
Click to collapse
Can you get in Download mode? To work with Odin you must be in Download mode, not recovery.
If you can get in Download mode, then start Odin and flash a TWRP Odin flashable recovery:
http://teamw.in/project/twrp2/101
Then at least you should have a functional recovery. From there you could either try to flash your stock ROM again, or any another ROM.
Are you 100% sure what you flashed was a good stock ROM for the T989 ?
Dont you have a nandroid you could restore?
Hi this is a long post so I will highly appreciate it if anyone helps me even after reading this.
I was on xperia z-ized v3.4 (based on android 4.3) with mj5 as the bootloader. I was tired of that rom and wanted to try dn3 rom and downloaded the zip as well but the OP of the rom thread said that twrp recovery is recommended over cwm. So I went to thread given in the page which showed me how to flash twrp. It was just download the zip and flash it in recovery, which is exactly what I did. Now ever since then I am not able to turn on my phone, nor does it go to recovery, it just goes into download mode which made me change my decision. Now I am thinking to downgrade back to 4.1.2 and I will try dn3 rom later on. I downloaded the firmware from sammobile but just wanted to ask that given my previous firmwares and flashes, is it safe to flash or will I risk bricking my phone.
Thanks for reading this and please help me out if you can
RazaVakil7995 said:
Hi this is a long post so I will highly appreciate it if anyone helps me even after reading this.
I was on xperia z-ized v3.4 (based on android 4.3) with mj5 as the bootloader. I was tired of that rom and wanted to try dn3 rom and downloaded the zip as well but the OP of the rom thread said that twrp recovery is recommended over cwm. So I went to thread given in the page which showed me how to flash twrp. It was just download the zip and flash it in recovery, which is exactly what I did. Now ever since then I am not able to turn on my phone, nor does it go to recovery, it just goes into download mode which made me change my decision. Now I am thinking to downgrade back to 4.1.2 and I will try dn3 rom later on. I downloaded the firmware from sammobile but just wanted to ask that given my previous firmwares and flashes, is it safe to flash or will I risk bricking my phone.
Thanks for reading this and please help me out if you can
Click to expand...
Click to collapse
Well if you still want to try DN3 ROM you can flash philz recovery tar.md5 via odin and then once you boot into recovery you can get twrp zip file that you downloaded previously and flash twrp over philz.That's what i do when i switch recoveries.I never used CWM except when i was on 4.1.2 but once i rooted my phone the same day i switched to philz.If you don't want to try dn3 at the moment yes you can go back 4.1.2 since you are on mj5 bootloader which makes downgrading back to 4.1.2 possible.I'm giving you links below for philz tar.md5 and instructions on how to flash it via odin incase you change your mind.
philz tar.md5
Put your phone into download mode,open odin on pc,uncheck auto reboot in odin,dont touch anything else,connect phone to pc,wait for port ID to lit up and be blue.Select the AP/PDA tab and navigate to flash this downloaded philz tar file.Click start and you are done.Exit odin on pc.Pull battery out your phone.Wait a minute then put it back in and manually enter recovery mode your newly flashed philz recovery will load.Now go and install twrp recovery zip file and select "reboot recovery" in philz advanced options.Your twrp recovery will load.Do all the wipes in twrp by going under advanced wipe (dont wipe external sd and otg) this will fully wipe your internal phone memory clean then go back to main menu and flash DN3.Enjoy.
singhpratik87 said:
Well if you still want to try DN3 ROM you can flash philz recovery tar.md5 via odin and then once you boot into recovery you can get twrp zip file that you downloaded previously and flash twrp over philz.That's what i do when i switch recoveries.I never used CWM except when i was on 4.1.2 but once i rooted my phone the same day i switched to philz.If you don't want to try dn3 at the moment yes you can go back 4.1.2 since you are on mj5 bootloader which makes downgrading back to 4.1.2 possible.I'm giving you links below for philz tar.md5 and instructions on how to flash it via odin incase you change your mind.
philz tar.md5
Put your phone into download mode,open odin on pc,uncheck auto reboot in odin,dont touch anything else,connect phone to pc,wait for port ID to lit up and be blue.Select the AP/PDA tab and navigate to flash this downloaded philz tar file.Click start and you are done.Exit odin on pc.Pull battery out your phone.Wait a minute then put it back in and manually enter recovery mode your newly flashed philz recovery will load.Now go and install twrp recovery zip file and select "reboot recovery" in philz advanced options.Your twrp recovery will load.Do all the wipes in twrp by going under advanced wipe (dont wipe external sd and otg) this will fully wipe your internal phone memory clean then go back to main menu and flash DN3.Enjoy.
Click to expand...
Click to collapse
Thanks a lot for the help, unfortunately I didn't like dn3 that much so tried to go back to stock but odin shows fail, so stuck with dn3 for a while until I find a solution
RazaVakil7995 said:
Thanks a lot for the help, unfortunately I didn't like dn3 that much so tried to go back to stock but odin shows fail, so stuck with dn3 for a while until I find a solution
Click to expand...
Click to collapse
Well try other 4.4.2 custom TW rom,dn3 isn't the only ROM available on xda for our note II.Look around and I am sure you'll find something that suits you.
singhpratik87 said:
Well try other 4.4.2 custom TW rom,dn3 isn't the only ROM available on xda for our note II.Look around and I am sure you'll find something that suits you.
Click to expand...
Click to collapse
Actually to be honest I want to go back to stock but I odin shows fail, so is there any workaround for that.
PS: even dn3 doesn't boot up now after flashing. Stuck on the note II logo. Tried wiping cache, dalvik cache and factory reset but to no avail
RazaVakil7995 said:
Actually to be honest I want to go back to stock but I odin shows fail, so is there any workaround for that.
PS: even dn3 doesn't boot up now after flashing. Stuck on the note II logo. Tried wiping cache, dalvik cache and factory reset but to no avail
Click to expand...
Click to collapse
Well which recovery are you using now?TWRP?Do you have a back up of any ROM? I suggest go under advanced wipe and wipe everything except external sd card and otg.This will fully wipe your phone.Other suggestion is flashing stock 4.4.2 ROM and then trying custom ROM.
singhpratik87 said:
Well which recovery are you using now?TWRP?Do you have a back up of any ROM? I suggest go under advanced wipe and wipe everything except external sd card and otg.This will fully wipe your phone.Other suggestion is flashing stock 4.4.2 ROM and then trying custom ROM.
Click to expand...
Click to collapse
Tried whatever you said just now, still not booting up. I am on philz recovery and I did not take any backup. I only have stock 4.1.2 rom which is not getting flashed via odin and I cannot download stock 4.4.2 because my internet connection is slow..
what should I do?
I am am trying to take my Samsung i317 AT&T Note 2 back to stock.
Installed 4.4.2 NJ1 stock rom using ODIN. Reset/ cleared and started phone and went to OTA upgrade the latest patch from AT&T to make it to NJ2. However, when the phone reboots, the Samsung Note II logo shows up and the screen does dark. When I try to enter recovery, it starts to reinstall the OTA patch all over again and says updated. Tried turning the phone back on and the same thing happens again.
I was able to get the phone to work by reflashing the NJ1 stock rom and installed the ZIP stock recovery file using CWM. However, I am trying to get back to the original stock configuration as possible without having CWM installed on the phone and was hoping I can install the stock recovery so that when I go to download mode, everything shows Samsung Official. Knox Warranty Void is at 1, so I guess there is nothing I can do to fix that at this point.
Would installing this be the simple fix by downloading 4.3 Param.bin and Tz.img
Another would be to install the stock recovery ZIP file using CWM as I have already successfully done and maybe someone can point me to find a way to uninstall the CWM afterwards. I've searched online to remove CWM but couldn't find the md5.tar file that would do that from ODIN.