Hi!
I tried to flash an Htc 8s with sdcard but my lock/unlock button has a little problem my phone restarted while flashing and dont want to start again. When i try to turn on my phone it vibrates but it doesn't want to turn on. If i connect it to pc via usb I see my phone like an usb stick where i can see system files. Can i reflash my phone without sdcard or it is bricked for good?
Please answer me!!
Related
help please!
i preformed task 29 on my tilt 2 and i now have an ATT screen and wont go any further. when i try to stat it it only goes as far as the first screen and no further. i tried resting it to no avail. i can not establish connection with pc. i have vista for pc. can somebody help please?
Yes. now u preformed that, you want to plug in your USB. Push reset and the lower volum button at the same time. You will go into boot loader mode. It should say USB on the bottom once u have made a connection after connecting your USB to the computer. At that point flash your Radio, after flashing your radio, flash your rom. All like you normaly would ..
PS. make sure Sim and MScard is out of phone before preforming Flashing Radio, then the rom. Then replace the sim card after all the installation from the rom you are installing..
First go back to the task 29 post and read all the instructions.
Task 29 is a memory wiper,it completely wipes the memory of the device leaving only the radio and basic functions.
To get up and running again follow these instructions:
1. Download the newest stock rom for ATT found in the Rom Development forum. http://forum.xda-developers.com/showthread.php?t=737168
2. Remove back cover from the device, remove the battery, remove the SIM card and remove the SD card if you have one. Reinstall the battery, do not replace the back cover.
3. Power up the device and connect it to the PC. Press the down volume button and press and hold the stylus into the reset button, hold both until the boot screen appears. Windows may install some software at this time, let the software install.
4. When USB appears at the bottom of the boot screen run the ROM installer software run. Follow ALL on screen instructions.
NOTE: If you have Hard SPL installed you can install any custom ROM, if not you MUST install a STOCK SHIPPED ROM.
twh said:
help please!
i preformed task 29 on my tilt 2 and i now have an ATT screen and wont go any further. when i try to stat it it only goes as far as the first screen and no further. i tried resting it to no avail. i can not establish connection with pc. i have vista for pc. can somebody help please?
Click to expand...
Click to collapse
First of all check to see if your phone is hardspl'ed by turning phone completely off then hold volume down key then power phone back on from here you should be on tri-color screen see what the spl version says if it says 0.85Olinex it's hardspl'ed anything else is not hardspl'ed.
If your phone is hardspl'ed then your good all task29 does is wipe your entire os off your phone thats why it won't boot to nothing but the startup screen so in order for it to boot you need to flash a rom on to it, so like before power phone off hold volume down key & power phone on you should be on tri-color screen again at the bottom of phone screen it should say serial now plug in usb from computer now it should say usb at the bottom of phone find a rom that you like then flash it phone should reboot after flash & work like normal once again.
Hope this helps
thank you all you guys. you all were awesome. as you could imagine, i am new to wm. but with the help of every body, i got my phone up and running.
twh said:
thank you all you guys. you all were awesome. as you could imagine, i am new to wm. but with the help of every body, i got my phone up and running.
Click to expand...
Click to collapse
no problem i'm glad we all were able to help you
Hi had all different roms on my DHD and settled on Ice cold sandwich which it has been running for a few months now, earlier on today I noticed that it had gone off and only the backlight was on, So I restarted it and it started loading the screen up but then just went into a loop.
So i pulled the battery and went into recovery and reloaded the ICS rom, but know it just vibrates 5 times and shows the splash screen and goes off with just the backlight on again.
I can get into fastboot but when i press the button for recovery it does the same I've tried every pd98img I could find and it says wrong image after I try and load them.
And when I connect it to the pc it can't be recognised by htcsync or thru any adb commands, and windows tried to load a driver called Q_USB-DLOAD or something similar then loads a qualcom usb driver but adb commands still won't recognise it, been looking all bnight for an answer getting desperate.
Thanx in advance Michael
1. Remove your sd card and try to boot up again if it boots up then there might be something corrupted on your sd. (Possible sd may have gone bad)
2. Try to enter hboot with power button and volume down at same time to see if you can get into hboot. If it dont your boot img may be damaged and you may need to push it again thru ADB.
3. If you can get into recovery try full wipe and reflashing rom. (You may have to use an adapter to get rom on to sd since computer dont see phone then place sd back in phone)
These are just a few ideas you can try hope it helps.
EDIT: Also there is no need to create a double post of the same issue. This is what causes clutter among the forum. When you post a question you need to wait for an answer not ask again when there is no reply on your first post. Thank you
Ok so first, let me say I know I done goofed. What happened was my phone (Note 2 GT-N7100) started to choke up a lot, battery life was ridiculously low and then suddenly my phone's language was constantly being switched to Italian.
I thought it might be a virus but a scan couldn't find anything. I deleted almost all apps in hopes it would stop but the phone went on with these weird glitches. In an act of desperation, I decided to wipe out everything and go back to factory settings.
Thing is my phone is rooted and I had the X Note Rom installed. When I tried the factory reset on TWRP, it still went back to the X Note Rom. That's when I dun goofed. I deleted EVERY ****ING THING in a desperate and stupid move.
Now when I press Volume Up + Home + Power I can get to Recovery Mode but I ain't got **** to install. If I press Volume Down + Home + Power I get into Odin mode but get a "Downloading... Do not turn off target!!" message that just hangs there forever.
To top it off, my computer won't recognize the damn phone anymore. Am I ****ed? Can I get myself out of this mess?! Please HELP!!!
Take it easy, download a custom rom, transfer it to the SD card, enter recovery and Flash it.
Since you can't connect the phone via USB, you need a SD card reader (if you have a laptop you 100% have it)
OR
You could flash the stock ROM through Odin, but it's more risky in my opinion. I would go with the 1st method
Mashed_Potatoes said:
Take it easy, download a custom rom, transfer it to the SD card, enter recovery and Flash it.
Since you can't connect the phone via USB, you need a SD card reader (if you have a laptop you 100% have it)
OR
You could flash the stock ROM through Odin, but it's more risky in my opinion. I would go with the 1st method
Click to expand...
Click to collapse
thanks... i'll try that when i get home (my SD card is there).
Hello, i have problem with my Xperia M. I try make ROM but CWM doesn't know flash boot.img and now i can't power on, flash mode and fastboot not work. This problem is other because pc don't see the mobile. Please help me with this problem. :crying: Thank for fast reply. :crying:
edit: i try connect to pc without battery, and now only blink blue led and it's all. how i can repair it?
edit2: i try open log file on PC (ubuntu) but i can't see mobile or other device.
Hello,
i tried flashing my Alcatel 5020x with SP Flash tool today. I tried once and everything went well except that it got stuck at the boot logo.
i then decided to format all except bootloader. The phone does not at all respond to anything after that. When plugged into computer or power it just has its led indicator on.
The PC does not detect it with or without battery. Not even any plug in/out sound on the PC.
I've tried different ports, uninstall drivers etc, nothing works.
Please Help!
If someone knows Test Point method for this device then please share!