Develop Bugs

Problem With sd card under motorolarom

When I have installed the motorola ROM my sd card don't work correctly...no image will be safed...
Under cm7 it works fine...
Can someone help me?
!I found a solution!
1. Download the zip
2. unzip
3. put your sc card in your PC/LAPTOP
4. Start the english.bat
5. Settings in Check Flash:
a) Acces Type = As physical Device
b) Device = Your SD Card
c) Action Type = Low level initialization
d) all other should now be gray then click start
6. in the new window delete the Fat32LBA Partition
7. Creat at sector 0 a new partition FAT32 WITHOUT LBA!!!
then click ok/finish and close Check Flash
8. press Start enter cmd
9. format X: /fs:fat32 /a:32K
Wait wait wait wait wait ... and then it should work perfect
I found the solution here

Dude don't spam in development forum... you could've posted it in general or Q & A forum
Sent from my MB525 using xda premium

Jojo1992 said:
When I have installed the motorola ROM my sd card don't work correctly...no image will be safed...
Under cm7 it works fine...
Can someone help me?
Sent from my MB526 using XDA App
Click to expand...
Click to collapse
There are problems with sd cards higher than class 6. You can do nothing expect using CM7. (it is a problem with the froyo kernel).

I already read that but I have a class 4 and a 4.5.1 full sbf
Sent from my MB526 using XDA App

Jojo1992 said:
When I have installed the motorola ROM my sd card don't work correctly...no image will be safed...
Under cm7 it works fine...
Can someone help me?
Sent from my MB526 using XDA App
Click to expand...
Click to collapse
I had that problem whit a brand new micro sd card on one of my friends defy.
I formated in a computer(not quick format) and all is ok now

sonyc2011 said:
I had that problem whit a brand new micro sd card on one of my friends defy.
I formated in a computer(not quick format) and all is ok now
Click to expand...
Click to collapse
And which ClusterSize? Best Regards

I do not know.. i did this thing from comand promt, diskpart.
Sent from my MB525 using XDA App

you could try this, navigate to your, DCIM folder and delete the thumbnails folder, on the phone or even on your pc.
then the phone will load all the thumbnails once again. keep note that, as many thumbnails you have, the slower the sd card will perform. it will not save any captured images, and will not also show any pics in the gallery. i think it has problem with indexing all the pics.
this was a problem in the official moto stock roms. that was the reason I left hd recording, and switched to cm7 from the 2.4 rom. im on defy red.

Please delete this

New solution look in post #01

thanks a lot .
I have a class 10 µSD , and , I still have trouble with , even after format it with the phone or in my computer , so I'm trying

mrdjol said:
thanks a lot .
I have a class 10 µSD , and , I still have trouble with , even after format it with the phone or in my computer , so I'm trying
Click to expand...
Click to collapse
The class 10 Micro SD are not working on Defy, so, by a class 6 ore 4 card.

[HOWTO] UnBrick T-Mobile S III QHSUSB_DLOAD w/Video Walkthrough

Other carriers and variants are still a work in progress
If you have a variant of the T999 other than the original T-Mobile SGH-T999 please contribute to the community and help us recover other users
If you have updated to 4.3 via OTA or flashed 4.3 firmware you will need to make sure you get the 4.3 debrick image.
Linux and Windows instructions are now included. Video only covers Linux.
Updated debrick links with zipped image files for lower bandwidth usage
I know there are some "How to unbrick" guides out there however they do no refer to an actual brick where you are stuck in QHSUSB-DLOAD mode.
The following guide will get you back to where you should be able to odin everything back to stock.
What you need:
Bricked SGH-T999
16GB or 32GB microSD card (all data will be erased from this sdcard)
microSD card reader
Linux Live Disc, VM with Linux with direct hardware control or native Linux OS. (Should work with OSx as well however I cannot confirm as I do not own one) Windows can be used, instructions below.
Everything in the ODIN guide
One of the following images based on your S III Model
SGH-T999 ***NOT FOR 4.3*** Debrick Image Thanks to @Techlyfe for the emmc dump
SGH-T999 4.3 only Debrick Image
SGH-T999L Debrick image Thanks to @DJ_SpaRky for the new T999L dump
SGH-T999N Debrick We still need one for this device
SGH-T999v ***NOT FOR 4.3*** Debrick Image
SGH-T999v 4.3 only Debrick Image @cLogic for the T999v 4.3 upload
How to get it done:
Linux Instructions
Boot your Linux OS
Download the debrick image listed in the Item's needed list
Open terminal on your Linux OS
Insert your microSD card into the reader
Plug your microSD card reader into your computer
Run
Code:
dmesg | tail
you should see something that mentions where it is mounted via /sdX
*
Code:
dd if=/path_to_debrick.img of=/dev/sdX
again where X is the microSD card ignoring the partition numbers as they should be overwritten
I had to do this a couple times for the image to actually take
*
Code:
parted /dev/sdX print
If you will see Error about the GPT table being corrupt you can type "OK" and then you will be given an option to Fix/Ignore; type "Ignore"
should show approximately 23 partitions (IIRC)
Windows Instructions
Download win32diskimager
Download your debrick image
Unzip both items and run win32diskimager
Run win32diskimager
browse for your extracted debrick image
Select your microSD in the dropdown box
Click write
Instructions required for both
remove the microSD card from the reader
remove the battery, sim and external microSD card from your device
insert your debrick microSD into your phone
insert the battery and down your power button (at this point your phone might actually boot completely and you can recovery any software/data you want)
reboot into Download mode either via adb or Volume Down + Home + Power
Once the device is booted into bootloader remove the microSD card.
follow the directions in the ODIN thread and make sure you UNCHECK partition!
* requires su privileges
Here's is a flashable zip to get the first 128M of the emmc which is what we use to create our debrick.img. It will create the debrick.img then compress it is a .zip format. Idea given to me from DocHoliday77 and used his original zip from here.
If you upload them I will mirror and link them to this post
PIT Files for ODIN when coming upon the error "PIT Partition does not exist"
Thanks to the following:
@gTan64 for finding the fix while repairing their friend's phone.
@CNexus for Link to original thread here where I found the answer for this
@Techlyfe again for the SGH-T999 emmc dump
@DocHoliday77 for the odin guide and software
@Matt for being Matt
@jmcoffey for the SGH-T999L dump
And My wife for letting me mess with her phone (which in turn bricked it by overwriting the apm partition)
@deBricker for their thread another walkthrough

RESERVED
Reserved for screenshots and future usage
I can usually be found on IRC Freenode #teambuild #teamkang or #teamgelato

Looking forward to hearing someone's results!
I can say that I do not believethis currently will work on a T999L, T999N, T999V. None of their firmware is compatible with each other. For example, if you try to flash ones firmware to another, it will cause a device to hard brick. So until versions for each model are posted, I wouldn't try this on anything but the T999.
Thanks for posting OP. Hoping it works!
Sent from my SGH-T999L using Tapatalk 4

DocHoliday77 said:
Looking forward to hearing someone's results!
I can say that I do not believethis currently will work on a T999L, T999N, T999V. None of their firmware is compatible with each other. For example, if you try to flash ones firmware to another, it will cause a device to hard brick. So until versions for each model are posted, I wouldn't try this on anything but the T999.
Thanks for posting OP. Hoping it works!
Sent from my SGH-T999L using Tapatalk 4
Click to expand...
Click to collapse
Sent you a PM requesting the T999L emmc dump. If we can get all the T999 Variants in here then it would be awesome. Apparently the fallback boot on the S III when the bootloader is corrupt is externalSD so we just emulate the bootloader onto the microSD and it booted perfectly for me when I bricked my wife's T999

Wow
This is truly a great thing !
Cant wait to see other the emmc dumps and to hear of results . The benefits of something like This is 10+ :good::good::good:
Thank You.

Qverse said:
This is truly a great thing !
Cant wait to see other the emmc dumps and to hear of results . The benefits of something like This is 10+ :good::good::good:
Thank You.
Click to expand...
Click to collapse
Can only wait until those in the Help/Q&A thread make it over this way. I'll try to get a video posted up later today.

Just wanted to clarify that gTan64 was the one who originally discovered this method while trying to fix a friend's bricked Sprint S3. He didn't actually brick his own S3
And to elaborate, it's not so much a fail-safe but more of a built-in feature that allows these phones to boot from an sdcard because you can do this even if your phone isn't in QHSUSB_DLOAD mode

CNexus said:
Just wanted to clarify that gTan64 was the one who originally discovered this method while trying to fix a friend's bricked Sprint S3. He didn't actually brick his own S3
And to elaborate, it's not so much a fail-safe but more of a built-in feature that allows these phones to boot from an sdcard because you can do this even if your phone isn't in QHSUSB_DLOAD mode
Click to expand...
Click to collapse
Thank you. I almost had all the details correct I will edit the OP to properly state that when I get back to a PC
Sent from my HTC One using Tapatalk 4

KAsp3rd said:
The image listed here is from the SGH-T999
I CANNOT confirm that it will work with the SGH-T999L version.
I know there are some "How to unbrick" guides out there however they do no refer to an actual brick where you are stuck in QHSUSB-DLOAD mode.
The following guide will get you back to where you should be able to odin everything back to where you need to be.
What you need:
Bricked SGH-T999
16GB or 32GB microSD card (all data will be erased from this sdcard)
microSD card reader
Linux Live disc or VM with Linux with direct hardware control (Should work with OSx as well however I cannot confirm as I do not own one)
Debrick Image || Mirror Thanks to @Techlyfe for the emmc dump
Everything in the ODIN guide
How to get it done:
Boot your Linux OS
Download the debrick image listed in the Item's needed list
Open terminal on your Linux OS
Insert your microSD card into the reader
Plug your microSD card reader into your computer
Run
Code:
dmesg | tail
you should see something that mentions where it is mounted via /sdX
*
Code:
dd if=/<path_to_debrick.img> of=/dev/sdX
again where X is the microSD card ignoring the partition numbers as they should be overwritten
I had to do this a couple times for the image to actually take
*
Code:
fdisk -l /dev/sdX
should show approximately 29 partitions (IIRC)
remove the microSD card from the reader
remove the battery, sim and external microSD card from your SGH-T999
insert your debrick microSD into your phone
insert the battery and down your power button (at this point your phone might actually boot completely and you can recovery any software/data you want)
reboot into Download mode either via adb or Volume Down + Home + Power
follow the directions in the ODIN thread and make sure you UNCHECK partition!
* requires su privileges
Thanks to the following:
@gTan64 for bricking their Sprint S III causing this thread to start
@CNexus for the answer and the link to the original thread where I found the answer for this Link to original post here
@Techlyfe again for the SGH-T999 emmc dump
@DocHoliday77 for the odin guide and software
@Matt for being Matt
And My wife for letting me mess with her phone (which in turn bricked it by overwriting the apm partition.
If someone has the SGH-T999L or SGH-T999V and wants to post the emmc dumps of those the instructions are as follows
busybox dd if=/dev/block/mmcblk0 of=/sdcard/debrick.img bs=1M count=128
If you upload them I will mirror and link them to this post
Click to expand...
Click to collapse
does it have to be on linux can i run it through command cmd on windows?

artojeda1988 said:
does it have to be on linux can i run it through command cmd on windows?
Click to expand...
Click to collapse
Has to on Linux or using Cygwin
Sent from my SPH-L710 using xda app-developers app

This is great news! I'm excited to hear confirmation.
Sent from my SAMSUNG-SGH-T999 using Tapatalk 4

KAsp3rd said:
The image listed here is from the SGH-T999
I CANNOT confirm that it will work with the SGH-T999L version.
I know there are some "How to unbrick" guides out there however they do no refer to an actual brick where you are stuck in QHSUSB-DLOAD mode.
The following guide will get you back to where you should be able to odin everything back to where you need to be.
What you need:
Bricked SGH-T999
16GB or 32GB microSD card (all data will be erased from this sdcard)
microSD card reader
Linux Live disc or VM with Linux with direct hardware control (Should work with OSx as well however I cannot confirm as I do not own one)
Debrick Image || Mirror Thanks to @Techlyfe for the emmc dump
Everything in the ODIN guide
How to get it done:
Boot your Linux OS
Download the debrick image listed in the Item's needed list
Open terminal on your Linux OS
Insert your microSD card into the reader
Plug your microSD card reader into your computer
Run
Code:
dmesg | tail
you should see something that mentions where it is mounted via /sdX
*
Code:
dd if=/<path_to_debrick.img> of=/dev/sdX
again where X is the microSD card ignoring the partition numbers as they should be overwritten
I had to do this a couple times for the image to actually take
*
Code:
fdisk -l /dev/sdX
should show approximately 29 partitions (IIRC)
remove the microSD card from the reader
remove the battery, sim and external microSD card from your SGH-T999
insert your debrick microSD into your phone
insert the battery and down your power button (at this point your phone might actually boot completely and you can recovery any software/data you want)
reboot into Download mode either via adb or Volume Down + Home + Power
follow the directions in the ODIN thread and make sure you UNCHECK partition!
* requires su privileges
Thanks to the following:
@gTan64 for bricking their Sprint S III causing this thread to start
@CNexus for the answer and the link to the original thread where I found the answer for this Link to original post here
@Techlyfe again for the SGH-T999 emmc dump
@DocHoliday77 for the odin guide and software
@Matt for being Matt
And My wife for letting me mess with her phone (which in turn bricked it by overwriting the apm partition.
If someone has the SGH-T999L or SGH-T999V and wants to post the emmc dumps of those the instructions are as follows
busybox dd if=/dev/block/mmcblk0 of=/sdcard/debrick.img bs=1M count=128
If you upload them I will mirror and link them to this post
Click to expand...
Click to collapse
I was searching for this emmc dump all last week, sent my phone out to get jTagged, get it back today and now I stumble across this :laugh:
Thank you very much kind sir for hooking us up!!

If you use this method please respond with your results as to show users that it has worked for you. If you would like to help with this for other variants of the S3 please inform me and I'll work with you to get what we need.
Sent from my HTC One using Tapatalk 4

KAsp3rd said:
What you need:
Bricked SGH-T999
16GB or 32GB microSD card (all data will be erased from this sdcard)
microSD card reader
Linux Live disc or VM with Linux with direct hardware control (Should work with OSx as well however I cannot confirm as I do not own
Click to expand...
Click to collapse
Don't mind me, I'm just adding a link to ubuntu live cd to make the resources easier to access for those who need to try this. I hope that is OK with you. If not, I'll remove it.
https://help.ubuntu.com/community/LiveCD#How-To_LiveCD_Ubuntu
BTW, I did not quote the entire OP lol, just the list

do i have to have a sd card reader or can i use a program to write it to my sd card

I would probably add the file to my sd card via the computer, and go from there.

HolyGhostBoy1 said:
do i have to have a sd card reader or can i use a program to write it to my sd card
Click to expand...
Click to collapse
What hardware do you have to use to copy to the image?
Sent from my One using Tapatalk 4

i have hardbricked t999v and can test this if i get debrick image

Fixed.But it don't write any data to sdcard.
Hope you can make a video soon

liongvn said:
Fixed.But it don't write any data to sdcard.
Hope you can make a video soon
Click to expand...
Click to collapse
Can you explain what you mean by your statement?

debrick.img for sgh-i257?

Can anyone make me a debrick.img for an sgh-i257? I assume it would be the same as sgh-i257m (the Canadian version). A friend of mine bricked his phone and it won't turn on at all (no recovery, no download mode, no logo, no... nothing). If I plug it in the computer, my computer makes that hardware plugged in sound.
I don't have another S4 mini that I could make the debrick.img with.

If anyone needs the instructions: http://forum.xda-developers.com/showpost.php?p=45725480&postcount=45
You just flash the file using CWM or TWRP and it creates a debrick.img file.

finally sgh-i257 dibreak done fro qualcomm qdload 9008 with sd card no jtag no box
first sorry for same language mistakes.
i have sgh i 257 dead. no power on no charging no download mode it gust stuck on emegency mode qualcomm qdload 9008 .I worked hard for that. i dont use ather at&t sgh-i257. but how i did it.
1-i looked fo similair sgh-i257 dibrick.img like i9195 s4 mini have to have 16 gb
2-i9195 dibrick.img have the same partitions size and tables as sgh-i257 but not working aft
er burning it on sd card.
3-the problem is the bootloader is not the same.
and what i did . i take sgh bootloader files aboot.mbn slb1.mbn....and ather partition image boot.img ... or tike all partitions image like system.img ...you find then in 4 files stock rom of sgh-i257.i extracted then with 7-zip.
3-in this step t looked for tool to inject all sgh-i257 partitions on i-9195 dibrick.img. finaly i find one after 13days of searching and testing.
i used this tool .injection is done. i burned dibrick.img on sd card on 32 gb sd card .it will work on 16 gb sd card because there is 20 gb unformatted size after burnig img file.and dont matter what tipe of sd card ,HC or any tipe. for me i used cheep 32 gb sd card it gust cust me about 14$ in my country.
4-i put the sd card in phone and i try to get in download mode in first nothing hapend. and i put the phone in usb cab. the phone make vibration and began charging .the battery was 0%.
i feeled very happy after 21 days the phone is did samthing..i put him charging about 5 m. and i cant weet to see if it will go to download mode.i tray to put him in download mode. and it worked. qualcomm qdload 9008 gone. and it remplaced with samsung modem.i flacher full rom with 4file and pit filles.flashing done.the phone is back.
*know i whitted this with my dibricked sgh-i257.
i think this method it will work on all samsung mobiles. of course there is models easy to find dibrick.img for them stocked on the net.
any help contact me [email protected]:good:

Unbrick LG G4 H811 9008 Qualcomm

Hi guys,
i came up with a temporary to unbrick LG G4 H811 , you just need a 32 GB SD card ( i used Sandisk 10 class) , the dump that i will link , and Win32 disk Imager, the SD card must low level formatted.
1- download this dump
http://www.mediafire.com/download/nkaarfueu161run/H811-10N-fulldump.zip
2- put the SD card in the PC and chose the dump file and write ( run as admin ):
3- put the sd card in the phone plug the battery and power on.
now you will be able to enter Download mode, the problem is that when you flash a firmware, it goes to the SD card rather than the EMMC memory. the Dump is included with TWRP recovery and an unlocked Bootloader, so if someone happens to know how to access or mount the EMMC memory that would be awesome
Edit : to recover SD card capacity and format, Download SD formatter Software

leptdre said:
Hi guys,
i came up with a temporary to unbrick LG G4 H811 , you just need a 32 GB SD card ( i used Sandisk 10 class) , the dump that i will link , and Win32 disk Imager, the SD card must low level formatted.
1- download this dump
http://www.mediafire.com/download/nkaarfueu161run/H811-10N-fulldump.zip
2- put the SD card in the PC and chose the dump file and write ( run as admin ):
3- put the sd card in the phone plug the battery and power on.
now you will be able to enter Download mode, the problem is that when you flash a firmware, it goes to the SD card rather than the EMMC memory. the Dump is included with TWRP recovery and an unlocked Bootloader, so if someone happens to know how to access or mount the EMMC memory that would be awesome
Click to expand...
Click to collapse
my lg g4 h811 stuck on qualcomm 9008 mode,no display, phone does not turned on, but connect as qualcomm 9008 while connected through usb. will this method work for me??

AwaisTariq20 said:
my lg g4 h811 stuck on qualcomm 9008 mode,no display, phone does not turned on, but connect as qualcomm 9008 while connected through usb. will this method work for me??
Click to expand...
Click to collapse
absolutely, you just need clean 32 GB class 10 SD card

I have H811. It has V20o but i mistakenly flashed Modem, Boot and Bootloader of V20i. Now its dead. No Download mode. No Charge Light No Boot. I have tried this SD Card Method but nothing happens when i connect my phone.
My system only detects "Qualcomm HS-USB QDLoader 9008" and nothing. Please help me

I Fixed it on my H811. For those who need help, i have written the thread
Visit http://forum.xda-developers.com/tmobile-g4/general/lg-g4-h811-complete-unbrick-guide-100-t3461629

Hi Everyone,
This fix is such a miracle but I have an H810 AT&T phone. Will this work for me ?
Thank you,

leptdre said:
Hi guys,
i came up with a temporary to unbrick LG G4 H811 , you just need a 32 GB SD card ( i used Sandisk 10 class) , the dump that i will link , and Win32 disk Imager, the SD card must low level formatted.
1- download this dump
http://www.mediafire.com/download/nkaarfueu161run/H811-10N-fulldump.zip
2- put the SD card in the PC and chose the dump file and write ( run as admin ):
3- put the sd card in the phone plug the battery and power on.
now you will be able to enter Download mode, the problem is that when you flash a firmware, it goes to the SD card rather than the EMMC memory. the Dump is included with TWRP recovery and an unlocked Bootloader, so if someone happens to know how to access or mount the EMMC memory that would be awesome
Edit : to recover SD card capacity and format, Download SD formatter Software
Click to expand...
Click to collapse
Please share h810 dump if anyone have it or make a dump for it

Shabby The Dev said:
Please share h810 dump if anyone have it or make a dump for it
Click to expand...
Click to collapse
Dont quote me , just make a thread man , i dont have , i asked for it and nobody gave it to me

my lg h810 9008 please help me
h810 work

aaya888 said:
h810 work
Click to expand...
Click to collapse
you see http://ouo.io/XK4tFF

Help Me
@leptdre
I have LG H811 hard brick please help me dump file ver 20p. Thanks !

hello i need vs986 dump file please thank you

Hello, its work with a LG G4 H811 V10d? and with memory of 16gb? Thank you.

Wow.
i see sign of life from my device after 1 year and 3 months., its say that it need charge .
do you find something new to make it const to emmc without sd card ?
Best.
Roee.

OK OK !
after using your method in H811 device and 4 gb sd card (thats all i got ) - i entered download mode and flashed H81110H_00.kdz rom with LG flash tool. ( i got a message in lg flash tool that server is offline - but i left that message on screen and saw that procedure is flash the rom in background ). - then my phone is wake and system up . ( only with sd card in , else its same 9008 mode )
the sd card left in with your files, i entered my sim ( fom local carrier - not T mobile ) -.
i left the phone as is - locked and charging - i wake up and found that i got android firmware update OTA H1110n (LMY47D). i did the update and then - its solved the problem dude.
no more sd card needed to be inside - its fix the emmc !
hope that its help to anyone with same problem here.

I have try this on at&t lg g4 h810 I can't get it to work any advice thanks
Sent from my LG-H830 using XDA-Developers mobile app

Rican39 said:
I have try this on at&t lg g4 h810 I can't get it to work any advice thanks
Sent from my LG-H830 using XDA-Developers mobile app
Click to expand...
Click to collapse
Do u have system image dump ? Plz share

zohaibkhan143 said:
Do u have system image dump ? Plz share
Click to expand...
Click to collapse
Is on the first page
Sent from my Nexus 6P using XDA-Developers mobile app
---------- Post added at 06:29 PM ---------- Previous post was at 06:27 PM ----------
Rican39 said:
Is on the first page
http://forum.xda-developers.com/showthread.php?p=69650207
Sent from my Nexus 6P using XDA-Developers mobile app
Click to expand...
Click to collapse
Sent from my Nexus 6P using XDA-Developers mobile app

H812 image badly needed
hi everybody....I really need a H812 unbrick dump image.....can I make one cause I got another h812 g4 operational phone....or is one posted somewhere?
thanks

Rican39 said:
Is on the first page
Sent from my Nexus 6P using XDA-Developers mobile app
---------- Post added at 06:29 PM ---------- Previous post was at 06:27 PM ----------
Sent from my Nexus 6P using XDA-Developers mobile app
Click to expand...
Click to collapse
that image is for H811.. I am asking for h810. If anyone have pls share it
---------- Post added at 08:00 PM ---------- Previous post was at 07:57 PM ----------
[email protected] said:
hi everybody....I really need a H812 unbrick dump image.....can I make one cause I got another h812 g4 operational phone....or is one posted somewhere?
thanks
Click to expand...
Click to collapse
This will help u
https://forum.xda-developers.com/showthread.php?t=2450045
Try this and then tell me does it work or not

lg g4 h811 unbrick

Tools Required:
1. Card Reader+Data Cable
2. A SD Card - 32 GB or 64 GB. I used 64 GB
3. SD Card Formatter - Download Here - Link Updated
4. Win32DiskImager - Download Here - Link Updated
5. Original KDZ - Download Here
6. SystemImage Bin File - Download Here - Link Updated
7. LGUP Tool - Download Here
Steps to Unbrick:
1. Insert your memory card in Card Reader and Format it using Windows Format. While formatting "uncheck Quick Format" and Change Type to "exFat". You can alternatively use SD Card Formatter but make sure that the card is in exFat format.
2. Once format is completed, install Win32DiskImager and open it. Add SystemImage.bin file. If it does not show the bin file just rename SystemImage.bin to SystemImage.img and then select it. Select your memory card and Click Write.
(You can alternatively change the file types on the win32diskimage from .img to all types)
Win32diskimage
3. One the Write Completes. Eject Card and insert in your LG G4 H811. Press Volume Up Button while connecting the USB Cable.
4. There you go, it will open the download mode. Now Open LGUP Tool as admin. It will show the device as connected. Select the Original KDZ Firmware and Click Start. it will complete and your Mobile will reboot.
5. Now its Done. Enjoy!
hey guys this is usefull method for you i guys i can guide you better in that regards let me know if you find intresting....