My kf2 was working fine but I ran out of room to install apps. I deleted unneeded apps still not enough room. I booted into twrp did a full wipe and now I can't side-load any roms to install. Twrp shows no OS installed. It will boot into twrp fine but nothing else. I have a fastboot cable. My computer recognizes my kf2 as an adb device but I can't seen to get anything to load. Some of the commands in KFFAID work but not all. I am trying to load cm11 and kitkat back. Any help would be appreciated.
James
getnby said:
My kf2 was working fine but I ran out of room to install apps. I deleted unneeded apps still not enough room. I booted into twrp did a full wipe and now I can't side-load any roms to install. Twrp shows no OS installed. It will boot into twrp fine but nothing else. I have a fastboot cable. My computer recognizes my kf2 as an adb device but I can't seen to get anything to load. Some of the commands in KFFAID work but not all. I am trying to load cm11 and kitkat back. Any help would be appreciated.
James
Click to expand...
Click to collapse
if sideload doesnt work then just do this, put the rom you want to flash and its gapps in the folder that adb is in, and run this while booted into twrp: adb push romnamegoeshere /sdcard/
then you can install the rom from inside twrp
didn't work
stunts513 said:
if sideload doesnt work then just do this, put the rom you want to flash and its gapps in the folder that adb is in, and run this while booted into twrp: adb push romnamegoeshere /sdcard/
then you can install the rom from inside twrp
Click to expand...
Click to collapse
Here is what happened. It said the device was not found. In the device manager it shows adb device under kindle fire.
Look on your task manager and kill every instance of adb.exe that you see and try again, I had that happen before when multiple instances were running. As long as it is in twrp then adb should work. If it continues to not work then uninstall the adb driver and if you see the MTP kindle device still there remove it as well, there might be a composite device that needs removing too, I find it a pita going between fastboot, recovery and whatever ROM os flashed if I use windows because of this, the drivers constantly have to be reinstalled when you change modes for me, hence why I avoid working with my kindle in windows and instead just use Linux. If you see any USB composite devices, check the hardware id's for a vid of 1949, if it has that then feel free to uninstall it. This may sound a bit complex, if you need more of an explanation just tell me.
Sent from my Amazon Kindle Fire HD using Tapatalk
No luck
stunts513 said:
Look on your task manager and kill every instance of adb.exe that you see and try again, I had that happen before when multiple instances were running. As long as it is in twrp then adb should work. If it continues to not work then uninstall the adb driver and if you see the MTP kindle device still there remove it as well, there might be a composite device that needs removing too, I find it a pita going between fastboot, recovery and whatever ROM os flashed if I use windows because of this, the drivers constantly have to be reinstalled when you change modes for me, hence why I avoid working with my kindle in windows and instead just use Linux. If you see any USB composite devices, check the hardware id's for a vid of 1949, if it has that then feel free to uninstall it. This may sound a bit complex, if you need more of an explanation just tell me.
Sent from my Amazon Kindle Fire HD using Tapatalk
Click to expand...
Click to collapse
My computer only recognizes the kindle as an adb device in fastboot mode. I haven't been able to use any of the adb commands on it with any luck. It says device not found. This only shows in kffaid version 4.1.87-beta.
*facepalm* you don't use adb commands with fastboot, you use fastboot commands with fastboot. When it is in twrp it should have adb access though...
Sent from my Amazon Kindle Fire HD using Tapatalk
I think I have a driver issue. I forgot to thank you for your help. If I could send the zip rom and gapps I could get it back to where it was. Is there anyway to start all over from the original kindle OS at this point?
Thanks you
You coukd restore it in fastboot using kffa but it seems like unnecessary work. I would boot a ubuntu 13.10 live cd/usb and just attempt it from there since there won't be any driver issues.
Sent from my LG-P769 using Tapatalk
I tried Ubuntu 12.04 LTS and it was to much trouble. I will try Ubuntu 13.10. I will have to learn the commands to use it.
Thanks
getnby said:
I tried Ubuntu 12.04 LTS and it was to much trouble. I will try Ubuntu 13.10. I will have to learn the commands to use it.
Thanks
Click to expand...
Click to collapse
these commands should do the trick assuming the repos are all active in the downloadable section of the software updates control panel.
Code:
sudo apt-get update
sudo apt-get install android-tools-fastboot
and after that the fastboot command will work but keep in mind to give it superuser privis with sudo or it probably wont work, i had forgotten that recently on my own pc since i don't deal with fastboot too often. ex: sudo fastboot -i 0x1949 getvar product
I had to work all weekend. I tried to get access through ubuntu 13.10. I used the commands you provided (sudo apt-get update). This command worked fine. When I used this command (sudo apt-get install android-tools-fastboot) It said I had to enable universe. I did some research and got that working and tried to use this command again (sudo apt-get install android-tools-fastboot) then this one worked fine. Then I tried the last command with my kindle in fastboot mode flashing green light (sudo fastboot -i 0x1949 getvar product ). The message was cannot connect to otter-2 ... device. Same thing I have been getting all along.
I think when I wiped the system I cleared all the software to connect to any external device. I don't know if I can even get access to restore the original OS. If you haven't guessed by now I an a noob. I think you realized that with my adb commands with fastboot enabled. I got the impression you knew when I saw the *facepalm* comment the the beginning of you post. When my kindle is booted to twrp my computer does not recognize it. My computer will recognize as an adb device when in fastboot mode. My computer will recognize it as a kindle (with a yellow triangle in the device manager) when it is trying to boot with the white and blue logo. I don't know what to do at this point. Here is a screen shot with adb side load from twrp.
Interesting, seems that data didn't want to mount. Have you tried adb from Linux while in twrp? Just run "sudo apt-get install android-tools-adb" to install the command, if you can get adb access at least then I may be able to help fix this depending on what exactly is wrong. BTW I didn't exactly think you were a noon with that facepalm, I just see people get that misconception a lot about adb and fastboot commands. What exactly did that fastboot command report back, I was surprised it was an error when I saw otter2 in the error considering that was what that command was sort of supposed to report back.
Sent from my Amazon Kindle Fire HD using Tapatalk
Here is where I am. See below. Now where do I put the file in ubuntu so I can access it from the terminal window. I am running ubuntu from a live CD. I tried the push command but it says no such file or directory. I told you I was a noob!
[email protected]:~$ adb devices
List of devices attached
0123456789ABCDEF recovery
Since adb is in a system path must out it in the current directory you are CD'd into, if you left the terminal alone it should be in ~ (the home folder of the Ubuntu account) so photo the home folder and drop it in there and run "adb push filename /sdcard/"
Considering that /data doesn't want to mount and that /sdcard os technically in /data, that command might not work depending on what's going on. I reccomend seeing if you can first and if not goto the months and mount /cache if its not mounted already, and they pushing a twrp update into it to try to reflash twrp, its small enough I think it should fit into the cache, though I don't think a ROM would fit.
Sent from my Amazon Kindle Fire HD using Tapatalk
I installed ubuntu on my laptop with windows 7. It seems to work better. I put the files in the home folder and the user folder. I mounted the cache and ubuntu said instead of unable to mount it was unable to access kindle now. Here is the terminal window results.
[email protected]:~$ sudo apt-get install android-tools-adb
[sudo] password for user:
Reading package lists... Done
Building dependency tree
Reading state information... Done
android-tools-adb is already the newest version.
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
[email protected]:~$ adb push cm-10.2-20130908-UNOFFICAL-otter2.zip /sdcard/
cannot stat 'cm-10.2-20130908-UNOFFICAL-otter2.zip': No such file or directory
[email protected]:~$
Um OK well the filenames are case sensitive in Linux so lookout for that. Also if it was in your home folder then it should have worked as long as you didn't CD anywhere else in the terminal first.
Sent from my Amazon Kindle Fire HD using Tapatalk
Problem Fixed
I fixed my problem. I had to restart my kindle into recovery mode and connect the fastboot cable to the computer and kindle before it booted into TWRP. At that point while booted into TWRP I used the push command in ebuntu terminal to sideload cm11 and gapps. After I loaded them I installed them with TWRP and rebooted. Now it is restored to where it was when I wiped it. I will not do the advanced wipe again.
adb push cm-11-20140202-NIGHTLY-otter2.zip /sdcard/
adb push gapps-kk-20131119.zip /sdcard/
Thanks for your help stunts513
Click to expand...
Click to collapse
Related
For 6.3 see http://forum.xda-developers.com/showthread.php?p=24129239
Please do not reupload/redistribute BurritoRoot2/BurritoRoot3, instead link directly to my hosting. I own the server, it will no go away any time soon. This allows me to update it if a bug is found.
BurritoRoot3 is not opensource, it is free, but it is not free to distribute. Please do not redistribute it.
Tested on 6.2, 6.2.1 and 6.2.2
Disclaimer:
BurritoRoot3 may void your warranty. While it was tested, over and over, a chance of data loss or hardware damage always exists. If something bad happens due to your use of BurritoRoot3, well it is your fault not our's, don't blame any of us.
Wine/Coffee/Device Funding:
To donate to jcase of TeamAndIRC for BurritoRoot go here:
http://forum.xda-developers.com/donatetome.php?u=2376614
To donate to pokey900 for the FireFireFire Bootloader go here:
http://forum.xda-developers.com/donatetome.php?u=466725
Download:
http://download.cunninglogic.com/BurritoRoot3.apk
BurritoRoot3 is an all in one package, to root and install the custom bootlaoder, FireFireFire, onto the KindleFire.
Instructions are pretty plain and simple, however you will have to get adb working on your own (if you have written, or know of adb guides for the Kindle Fire please PM me to list them here).
ADB GUIDES
MAC GUIDE: http://forum.xda-developers.com/showthread.php?t=1443071
WINDOWS GUIDE: http://www.jayceooi.com/2011/12/13/how-to-install-kindle-fire-adb-usb-driver/
LINUX GUIDE: http://forum.xda-developers.com/showthread.php?p=22067293
What it does:
Gains root, installs superuser, installs su and installs the FireFireFire bootloader.
At this time, we do not have permission to distribute any recovery, once one is available for our use, we will add auto flashing of recovery.
How to use:
adb shell chmod 777 /data/local/tmp
Run app, follow directions given by the app.
Usage example :
[email protected]:~$ adb shell chmod 777 /data/local/tmp <---- This one is important, it may not create BurritoRoot3.bin if this is not done
[email protected]:~$ adb install BurritoRoot3.apk
4897 KB/s (1151520 bytes in 0.229s)
pkg: /data/local/tmp/BurritoRoot3.apk
Success
<go open the app now>
[email protected]:~$ adb shell /data/local/tmp/BurritoRoot3.bin --root
BurritoRoot3 Installer 0.1 by TeamAndIRC
#########################################################################
Usage: BurritoRoot3.bin <parameter>
--root - Restart adbD as root, and install Superuser app
--install - Install su
#########################################################################
Gaining root...
Installing Superuser APP, if it erros as already exists, please ignore the error.
pkg: /data/data/net.andirc.burritoroot3/bin/Superuser.apk
Success
Restarting adbD as root...
Please run adb shell /data/local/tmp/BurritoRoot3.bin --install
[email protected]:~$ adb shell /data/local/tmp/BurritoRoot3.bin --install
BurritoRoot3 Installer 0.1 by TeamAndIRC
#########################################################################
Usage: BurritoRoot3.bin <parameter>
--root - Restart adbD as root, and install Superuser app
--install - Install su
#########################################################################
BurritoRoot3 kroot 0.1 - TeamAndIRC
Remounting /system...
Cleaning up, ignore any errors
rm failed for /system/xbin/su, No such file or directory
rm failed for /system/bin/su, No such file or directory
Installing su...
Remounting /system..
Root installed
Starting: Intent { act=android.intent.action.MAIN cmp=net.andirc.burritoroot3/.FireFireFire }
Please check your Kindle's screen
[email protected]:~$
If you already have root, and want to safely install the FireFireFire bootloader, you can use the app, just install, open/close the app then
adb shell am start -a android.intent.action.MAIN -n net.andirc.burritoroot3/net.andirc.burritoroot3.FireFireFire
To install the CWR recovery by DoomLord after gaining root:
Download it, and push it to your Kindle
adb push <filename> /data/local/recovery.img
adb shell dd if=/data/local/recovery.img of=/dev/block/platform/mmci-omap-hs.1/by-name/recovery
Would you support the archos G9 devices
jutley said:
Would you support the archos G9 devices
Click to expand...
Click to collapse
Doesn't archos sign or lock system?
I love you Devs so much. I just got a Kindle today, but as I watched the video your Kindle shows up under Other Devices as if it didn't install the device driver. Mine is installed under portable devices. Can I just update that one or is there a debug mode for the Kindle that I'm missing?
Thanks for all you do!
---------- Post added at 10:06 AM ---------- Previous post was at 09:55 AM ----------
CharlieBoy808 said:
I love you Devs so much. I just got a Kindle today, but as I watched the video your Kindle shows up under Other Devices as if it didn't install the device driver. Mine is installed under portable devices. Can I just update that one or is there a debug mode for the Kindle that I'm missing?
Thanks for all you do!
Click to expand...
Click to collapse
LoL Nevermind I think I know why mine isn't there... I've already installed ADB from before. I shall continue on and see what happens :-D
I'm currently running Ubuntu 11.10(Without access to a windows computer to do so.) And after following the steps within the BurritoRoot I get error: insufficient permissions for device when entering adb root. I've rebooted my kindle and laptop as well as changed usb ports.
I've set it up so that it's acknowledged within /.android. Am I perhaps missing something sdk wise? The usb configuration install for extras within it says Linux isn't compatible. But any insight into this would be appreciated I'm not new to Android or adb for that matter. Things seem to be done differently for the Kindle is all.
Thanks guys.
AproSamurai said:
I'm currently running Ubuntu 11.10(Without access to a windows computer to do so.) And after following the steps within the BurritoRoot I get error: insufficient permissions for device when entering adb root. I've rebooted my kindle and laptop as well as changed usb ports.
I've set it up so that it's acknowledged within /.android. Am I perhaps missing something sdk wise? The usb configuration install for extras within it says Linux isn't compatible. But any insight into this would be appreciated I'm not new to Android or adb for that matter. Things seem to be done differently for the Kindle is all.
Thanks guys.
Click to expand...
Click to collapse
adb kill-server
sudo -s
adb devices
should see it now
Quit following me around jcase
Unheard said:
Quit following me around jcase
Click to expand...
Click to collapse
Hah Where you been?
I can not get ADB to recognize the device for the life of me.
I know I have the drivers installed the Fire is recognized as "android composite adb interface" under the Android Phone category in Device manager. But I can not get adb to see it.
"Adb kill-server"
"adb devices"
and it shows no devices attached. Ive done a factory reset on the tablet just to see (knowing it wouldn't make a difference)
Im running Windows XP
if someone could help me out.
notsointeresting said:
I can not get ADB to recognize the device for the life of me.
I know I have the drivers installed the Fire is recognized as "android composite adb interface" under the Android Phone category in Device manager. But I can not get adb to see it.
"Adb kill-server"
"adb devices"
and it shows no devices attached. Ive done a factory reset on the tablet just to see (knowing it wouldn't make a difference)
Im running Windows XP
if someone could help me out.
Click to expand...
Click to collapse
I'm sure its related to windows' drivers but I have no clue. Sorry
jcase said:
adb kill-server
sudo -s
adb devices
should see it now
Click to expand...
Click to collapse
Thanks man, I knew I must have failed to do something. It's much appreciated.
Dis this last night and it worked fine. Thanks!
I did have a few minor stumbles though. It seems the newest version of the software changed the name of the superuser app but the guide still uses the old name in the install command. Once I realized this I just changed the name in the command and it went right in.
Also for some reason I couldn't select the text in the adb box on the web page so I had to enter the commands by hand. No big deal but I would have felt more secure if the commands were in simple text so I could have copy/paste them in.
Like I said though everything worked and I have the market installed now. Thanks for the hard work!
I'm having some trouble with mine...I am trying to follow the video instructions to the link but it shows downloading a .android folder and extracting it to my user name on desktop but there is no such link. I have downloaded SDK and installed google usb drivers as well. I have 6.2.1 firmware and downloaded kindleroot_androidpolice.apk and placed on my kindle and I also downloaded superuser-2. I am not able to install the driver to the fire either. I go to my computer, manage, device manager, kindle, update driver software, browse my computer, etc. I have no INF file to choose under my .android folder.
Any help would be appreciated
My sd card is showing up as unmounted and not sure how to remount it. I sent adb remount and it didn't work. Any help would be appreciated.
Fee454 said:
I'm having some trouble with mine...I am trying to follow the video instructions to the link but it shows downloading a .android folder and extracting it to my user name on desktop but there is no such link. I have downloaded SDK and installed google usb drivers as well. I have 6.2.1 firmware and downloaded kindleroot_androidpolice.apk and placed on my kindle and I also downloaded superuser-2. I am not able to install the driver to the fire either. I go to my computer, manage, device manager, kindle, update driver software, browse my computer, etc. I have no INF file to choose under my .android folder.
Any help would be appreciated
Click to expand...
Click to collapse
would suggest to use this:
http://forum.xda-developers.com/showthread.php?t=1399889
[/COLOR]
b63 said:
would suggest to use this:
http://forum.xda-developers.com/showthread.php?t=1399889
Click to expand...
Click to collapse
This tool will attempt to install the correct Drivers for the Kindle Fire.
It will also perform the setup required for adb_usb.ini in .android for you.
The system cannot find the path specified.
The system cannot find the path specified.
The system cannot find the path specified.
The system cannot find the path specified.
The system cannot find the path specified.
The system cannot find the path specified.
Press any key to continue . . .
I tried to install the drivers for the kindle but i receive the above message
---------- Post added at 09:56 PM ---------- Previous post was at 09:07 PM ----------
My issue is it cannot find my device...where can I find the kindleADB.zip I keep hearing about?
did you do install_drivers.bat first ?
take a look:
http://forum.xda-developers.com/showpost.php?p=20698002&postcount=283
that should correct the path issue
You should get the same files from the android Sdi. Good luck.
Jcase, I know that you said the unroot button did not work, but is there a method of unrooting?
b63 said:
did you do install_drivers.bat first ?
take a look:
http://forum.xda-developers.com/showpost.php?p=20698002&postcount=283
that should correct the path issue
Click to expand...
Click to collapse
Yes thank you. Moving it to the same as the run.bat seemed to have worked as it shows online now when running the Kindle Fire Utility. I switched it to fast boot but now seems to have been frozen at the kindle fire logo for quite some time now. I heard you have to switch to fastbook to install TWRP first before rooting?
I am not sure if I should attempt to somehow reboot this as it seems to be stuck at the boot up screen
wrong - switch back to normal boot and use the utility
Hi guys! I'm new to the forum but not new to the IT world and not new to Linux or Android devices.
I'm stuck at the Kindle Fire screen after a failed attempt to root the device. Here's what I did. I'm hoping somebody can please help me. I did lots of Google searches to try to solve my issue and I can't seem to find the right solution.
So here's the background. I tried to root my KF by using this process http://www.pcworld.com/article/244303/how_to_root_your_kindle_fire.html on an Windows 7 VM. Then I found that SuperOneClick didn't work for KF6.3. So then I tried to KF Utility v.0.9.5 http://forum.xda-developers.com/showthread.php?t=1399889
I selected the option to root the KF. After it went through the process and I got the Kindle Fire screen (which is sounds like the KF is in the fastboot process) I couldn't get anything to work at that point. I couldn't get the VM to even see the KF nor Ubuntu (which is the main OS of that laptop). So then I figured I bricked the device. So I followed these instructions http://www.androidauthority.com/how-to-unbrick-your-amazon-kindle-fire-46412/ but that won't work ecause the KF isn't being recognized by the OS. SO at that point, I couldn't get anything to work. So I rebooted the laptop (which is running Ubuntu 12) and the KF booted back up and it fired back up.
If I power off the KF and turn it back on, it gets stuck at the KF bootup screen.
So at that point I decided to throw Windows 7 on a different laptop that I have and see if I can get it to work. So I installed java & Android ADK for my OS (Windows 7). I installed the USB driver and updated the packages. So I go through these instructions first http://forum.xda-developers.com/showthread.php?t=1568340 and I can't get the KF to be recognized as a device through adb. So I go back to the PC World instructions (linked above) and I follow steps through step 8. And I still can't get the KF to be displayed through adb. When I try to kill the adb server and then enter adb devices, I still can't get the KF to be recognized.
Oh and btw, Windows 7 does recognize the device as a "Kindle".
Any help would be greatly appreciated.
Sparty On!
Use the following fastboot commands:
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
or
adb shell idme bootmode 4000
adb this should be the way it works:
Sent from my Amazon Kindle Fire using Tapatalk 2
Thanks for the reply.
Unfortunately, I tried it and I get an invalid usage error. -i isn't a valid option. I can use -w, -s, -p, or -c.
I also obtained fastboot from the CyanogenMod Wiki for Fastboot and copied the exe to the /android-sdk/platform-tools folder and tried it. I also followed the wiki and copied it and found that placing it in the /tools/ directory wouldn't work because the missing .dll file isin the platform-tools directory and not in the tools directory.
I'm having the same problem I think since windows doesn't recognize my kindle I can't install the drivers.
AndroidSparty said:
Thanks for the reply.
Unfortunately, I tried it and I get an invalid usage error. -i isn't a valid option. I can use -w, -s, -p, or -c.
I also obtained fastboot from the CyanogenMod Wiki for Fastboot and copied the exe to the /android-sdk/platform-tools folder and tried it. I also followed the wiki and copied it and found that placing it in the /tools/ directory wouldn't work because the missing .dll file isin the platform-tools directory and not in the tools directory.
Click to expand...
Click to collapse
Us the same commands without -i 0x1949
fastboot oem idme bootmode 4000
fastboot reboot
Sent from my Amazon Kindle Fire using Tapatalk 2
ammubarak said:
Use the following fastboot commands:
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
or
adb shell idme bootmode 4000
adb this should be the way it works
Click to expand...
Click to collapse
None of these commands will work without first being able to communicate with the device. In order to communicate with the device you need working drivers. And even though Windows says the drivers are installed, it doesn't mean they are working.
For some reason, the Kindle Fire Utility, along with Windows is a bad combination. You could try to uninstall and delete the current drivers then reinstall OR set up your Linux to run adb and fastboot commands from the terminal.
From they way it sounds, your device is already rooted. All you need to do at this point is change the bootmode. This can easily be done in Linux as long as you are in root. For more info on bootmodes and drivers, read this thread:
http://forum.xda-developers.com/showthread.php?p=23747567
From a command prompt in windows CD over the the folder containing fast boot. One your command prompt is in that folder type fast boot devices. If it says that no devices found then you have a driver issue. What needs to be done next is open the folder containing kfu and run drivers.bat. this should install the appropriate drivers. Once this is done open kfu, select option one, then option 2. This should cause your fire to reboot in normal mode. IF that doesn't work you can push a boot.img to your fire in fast boot if for some reason you fouled up the system directory. Let me know if that does the trick first, if not I'll explain how to fastboot it back to a working condition.
Edit: in kfu select the option that says normal boot mode. Not sure if its option 2 or not. I'm not in front of my PC
Sent from my MB860 using XDA
I received mine with 6.3 and KFU wouldn't recognize it even after using the driver installation. BUT I found way around it. You need to install the drivers manually, and then KFU will work. Download the drivers, then extract the .android folder (create it if you don't have one) to
C:\Documents and Settings\YOURUSERNAME\.android open up your device manager, click on the Kindle and follow the UI to select the .android folder. Restart and use KFU. Enjoy!
soupmagnet said:
None of these commands will work without first being able to communicate with the device. In order to communicate with the device you need working drivers. And even though Windows says the drivers are installed, it doesn't mean they are working.
For some reason, the Kindle Fire Utility, along with Windows is a bad combination. You could try to uninstall and delete the current drivers then reinstall OR set up your Linux to run adb and fastboot commands from the terminal.
From they way it sounds, your device is already rooted. All you need to do at this point is change the bootmode. This can easily be done in Linux as long as you are in root. For more info on bootmodes and drivers, read this thread:
http://forum.xda-developers.com/showthread.php?p=23747567
Click to expand...
Click to collapse
Thanks for the info. I'm on my Windows box now, but i'll try the Linux directions in that URL tomorrow and will get back to you. Thanks!
backspacepc said:
From a command prompt in windows CD over the the folder containing fast boot. One your command prompt is in that folder type fast boot devices. If it says that no devices found then you have a driver issue. What needs to be done next is open the folder containing kfu and run drivers.bat. this should install the appropriate drivers. Once this is done open kfu, select option one, then option 2. This should cause your fire to reboot in normal mode. IF that doesn't work you can push a boot.img to your fire in fast boot if for some reason you fouled up the system directory. Let me know if that does the trick first, if not I'll explain how to fastboot it back to a working condition.
Edit: in kfu select the option that says normal boot mode. Not sure if its option 2 or not. I'm not in front of my PC
Sent from my MB860 using XDA
Click to expand...
Click to collapse
Good news, I ran fast boot devices without an error. Bad news, it didn't list any devices. Just sent me to another blank command line.
When I initially ran install drivers.bat through FK Utility, it installed the drivers successfully, from what it said. I just ran it again and it said the drivers were installed successfully and the driver name is Google, Inc (WinUSB).
When I ran KF Utility (run.bat), it says that the ADB Status is offline. At this point, I would think that since ADB is offline, the Utility won't work? Stupid Windows!!!
AndroidSparty said:
Thanks for the info. I'm on my Windows box now, but i'll try the Linux directions in that URL tomorrow and will get back to you. Thanks!
Good news, I ran fast boot devices without an error. Bad news, it didn't list any devices. Just sent me to another blank command line.
When I initially ran install drivers.bat through FK Utility, it installed the drivers successfully, from what it said. I just ran it again and it said the drivers were installed successfully and the driver name is Google, Inc (WinUSB).
When I ran KF Utility (run.bat), it says that the ADB Status is offline. At this point, I would think that since ADB is offline, the Utility won't work? Stupid Windows!!!
Click to expand...
Click to collapse
Actually it will, status will still be off line, just select the boot mode option, and then on the next screen select normal bootmode
Sent from my MB860 using XDA
For future reference if you want to use Linux to issue fastboot and adb commands, here's the tutorial:
http://forum.xda-developers.com/showthread.php?p=22067293
I'd suggest using Linux as it is WAY more stable and WAY more reliable.
soupmagnet said:
For future reference if you want to use Linux to issue fastboot and adb commands, here's the tutorial:
http://forum.xda-developers.com/showthread.php?p=22067293
I'd suggest using Linux as it is WAY more stable and WAY more reliable.
Click to expand...
Click to collapse
I completely agree, I use and am familiar with both and it sounded like he was trying to do it from a windows machine.
Sent from my MB860 using XDA
backspacepc said:
I completely agree, I use and am familiar with both and it sounded like he was trying to do it from a windows machine.
Sent from my MB860 using XDA
Click to expand...
Click to collapse
Actually...I'm a she.
Since I have both available to me...it sounds like I should scrap the Windows (which is an understatement anyway) and use Linux/Ubuntu. That I can do!
I'll try the Linux directions later today and will let you know how I come out. Thanks again for the help!
Edit: Okay just tried it & I still can't get adb & fastboot to recognize the device. I followed the "Enable ADB under Ubuntu/Linux" directions and still nodda.
AndroidSparty said:
I'll try the Linux directions later today and will let you know how I come out. Thanks again for the help!
Edit: Okay just tried it & I still can't get adb & fastboot to recognize the device. I followed the "Enable ADB under Ubuntu/Linux" directions and still nodda.
Click to expand...
Click to collapse
Sorry ma'am! did you also try the directions I posted for windows as far as kfu? Its starting to sound like you may not have fully flashed fff
Sent from my MB860 using XDA
backspacepc said:
Sorry ma'am! did you also try the directions I posted for windows as far as kfu? Its starting to sound like you may not have fully flashed fff
Sent from my MB860 using XDA
Click to expand...
Click to collapse
You may also want to try to rerun your root script, oddly enough I've had that work before too.
Sent from my MB860 using XDA
AndroidSparty said:
Edit: Okay just tried it & I still can't get adb & fastboot to recognize the device. I followed the "Enable ADB under Ubuntu/Linux" directions and still nodda.
Click to expand...
Click to collapse
Did you notice the second post in the Linux tutorial?
kinfauns said:
Thanks for the guide on setting this up for linux. I just wanted to point out a small error in the instructions. The echo command above is incorrect and will not do what you intended. It should be corrected to
Code:
echo 0x1949 >> ~/.android/adb_usb.ini
Click to expand...
Click to collapse
backspacepc said:
Sorry ma'am! did you also try the directions I posted for windows as far as kfu? Its starting to sound like you may not have fully flashed fff
Sent from my MB860 using XDA
Click to expand...
Click to collapse
I just ran kfu and I I was able to get it to do a normal boot. YAY!
Then I ran the .bat file in the KFU and I selected the permanent root. During the activating fastboot, it said that "Oops something went wrong...." it couldn't find the kindle. Then it installed twrp.img is missing and it downloaded successfully. So then I got the Notice, and it's installing TWRP and it's waiting for the device. I turned the Kindle off & on a few times to get the KFU to recognize the Kindle, and no luck. At least I was able to boot into the KF while it's still still waiting for the device. BUT....at this point during the TWRP install process, it's waiting for the device and not recognizing it.
soupmagnet said:
Did you notice the second post in the Linux tutorial?
Click to expand...
Click to collapse
I did, but I used vi instead of gedit. And i verified that 0x149 was in the file on a new line.
AndroidSparty said:
I did, but I used vi instead of gedit. And i verified that 0x149 was in the file on a new line.
Click to expand...
Click to collapse
I can't imagine why using vi would make any difference but you could try gedit to see if it works.
As for TWRP, you could install it manually (Windows). Make sure you have a connection with adb/fastboot and use KFU to set your device to fastboot mode. Keep in mind when you do this that you may have to go through the whole process of fixing your drivers again (blame Windows/KFU).
When you're in fastboot mode, hold the power button until the device shuts down.
Shift + right click the KFU folder that contains fastboot (tools) and open as a command
In the prompt that comes up, enter:
Code:
fastboot -i 0x1949 flash recovery /path/to/twrp2.1.img
When your prompt says "waiting for device", turn the device back on.
Make sure it's twrp 2.1 Version 2.0 is installed in a different manner and will most likely cause problems if installed with the "flash recovery" command.
I was just messing around with TWRP trying to flash a new ROM. I forgot to make a backup and wiped the internal storage + system (in other word I wiped everything) I have the files in my computer but I don't know how to access them since the computer can't recognize my device. Any suggestions? :crying:
You need to enter recovery and adb push the files to your sdcard. Open a command window where adb is located
Code:
adb push rom.zip/sdcard/
Thepooch said:
You need to enter recovery and adb push the files to your sdcard. Open a command window where adb is located
Code:
adb push rom.zip/sdcard/
Click to expand...
Click to collapse
Since the device can't be recognized I would try to search for the ADB drivers. This happened to me on my kindle fire hd 7" and the only way I could fix it was by doing "adb sideload filenamehere.zip" after going into Advanced > ADB Sideload.
Hope I could help!
I'm very grateful
thanks
you rock bro
Thepooch said:
You need to enter recovery and adb push the files to your sdcard. Open a command window where adb is located
Code:
adb push rom.zip/sdcard/
Click to expand...
Click to collapse
Im new to this world of tablets and all the commands and prompt, etc... but I thought that I would never solve my problem lol. I'm still a noob but
Thank you for all what you did for my kindle fire hd. I just wanna let people know you helped me unbrick my kindle ( you worked more than 4 hours to be exactly on my kindle) not many people in this forum would do that :good: and thanks to all the developers and mods you nailed it quite well on unbricking my kindle using the programs they have developed.
Editing the drivers so they could work on my machine (I live in El Salvador so my region is a problem when i try to install the drivers) was no easy quest and using teamviewer for letting you work was cool, but the best part is that you installed the cm10.1 by Hash which I had before bricking my device. You saved my kindle bro, thanks A LOT!!!!! I appreciate it. :victory:
Hello, I Have a Kindle Fire 1st Gen. I Had CM 10.1 on it. I was attempting to put AOSP back on it for My Wife. I did I Noobish Move at 4 am half asleep, I Did NOT go into advanced mode in TWRP and uncheck DATA in the Wipe tab. So This Screwed me "Bricked" Message comes up in TWRP when rebooting, says ( NO OS ) . I have Tried Kindle unbrick utility with no success when clicking on "Stuck at Logo" in utility I get this Error ...> PIC Attatched!>
I then Tried Using android-sdk ( I have went in and edited the files that need to be edited in program files/android...> File_android_winusb as well as in .android folder in the appdata location) Along with CMD & I get a Error So far into the process of Resetting Kindle OS. Pic Attatched as well. It Seems Like I have something missing ?!?!?
I somewhat Suck at CMD, I don't have much experience with it, so Please go slow on me,when Giving advise....
Thanks In Advance!!
If you still have access to TWRP, use it to mount your sdcard to USB.
soupmagnet said:
If you still have access to TWRP, use it to mount your sdcard to USB.
Click to expand...
Click to collapse
I Tried That. I See the Device But when double clicking, It will not let me access it.
Butt Nugget said:
I Tried That. I See the Device But when double clicking, It will not let me access it.
Click to expand...
Click to collapse
Oh that's right, it won't work on 2nd generation devices.
Do you have your drivers installed? Are you able to send any adb commands (adb devices)?
soupmagnet said:
Oh that's right, it won't work on 2nd generation devices.
Do you have your drivers installed? Are you able to send any adb commands (adb devices)?
Click to expand...
Click to collapse
My Kindle is a 1st Gen. I'm not sure If I understand what You are talking about when You say "send Commands/devices" If Your talking about in CMD I Get all the way to Seeing my Device Serial Number for Kindle. The when I type "adb shell" I get a error saying (Failed: No such file or directory <2> - ) You can see this in the screen shot I attached to this thread..
Sorry, I looked at what forum this was in and got a little confused...silly me :silly:
Anyway, back on track...
You should not be receiving that error in TWRP. If you are, then something is seriously wrong with it and probably needs to be reinstalled. Other than that, I'm having trouble seeing where the problem is. (the pic shows that you're not in recovery, btw)
You clearly have access to adb, so...why aren't you using 'adb push' to transfer a new ROM to your sdcard to flash in recovery?
soupmagnet said:
Sorry, I looked at what forum this was in and got a little confused...silly me :silly:
Anyway, back on track...
You should not be receiving that error in TWRP. If you are, then something is seriously wrong with it and probably needs to be reinstalled. Other than that, I'm having trouble seeing where the problem is. (the pic shows that you're not in recovery, btw)
You clearly have access to adb, so...why aren't you using 'adb push' to transfer a new ROM to your sdcard to flash in recovery?
Click to expand...
Click to collapse
I've Done searches and only found how to attempt recovery, typing in commands on pc's CMD Prompt while kindle is mounted to usb in twrp and typing commands in on CMD in pc I installed Android SDK and Device driver. So Sounds possibly what I tried is totally different from what Your asking if i done? If So, Could You Explain step by step thee method with new roms or send me in the right directions 2 a how to link or video? Anything I would appreciate GREATLY! :fingers-crossed:
Butt Nugget said:
I've Done searches and only found how to attempt recovery, typing in commands on pc's CMD Prompt while kindle is mounted to usb in twrp and typing commands in on CMD in pc I installed Android SDK and Device driver.
Click to expand...
Click to collapse
I have no idea what you're saying.
All you need to do is, boot into recovery (TWRP), use adb to "push" a ROM to your sdcard (adb push...), then install the ROM in recovery.
soupmagnet said:
I have no idea what you're saying.
All you need to do is, boot into recovery (TWRP), use adb to "push" a ROM to your sdcard (adb push...), then install the ROM in recovery.
Click to expand...
Click to collapse
I mentioned Earlier (say, the Drive of the device is :F) In My computer, When I click :F It states Cannot access (Drivers are installed for kindle). I'm asking How Can I Mount USB in TWRP and Put ROM File on sdcard when I cannot access it... I Do Not have a Micro USB OTG to USB 2.0 Cable to plug up to kindle with the files put on a external HD to complete this course.
Does that make more since?
Butt Nugget said:
I mentioned Earlier (say, the Drive of the device is :F) In My computer, When I click :F It states Cannot access (Drivers are installed for kindle). I'm asking How Can I Mount USB in TWRP and Put ROM File on sdcard when I cannot access it... I Do Not have a Micro USB OTG to USB 2.0 Cable to plug up to kindle with the files put on a external HD to complete this course.
Does that make more since?
Click to expand...
Click to collapse
Try to understand what you're being told. I'm not saying anything about mounting your sdcard to transfer files to it so get that idea out of your head for a moment.
You need to boot into recovery and use the command 'adb push' to transfer a ROM to your sdcard, then flash it in recovery.
Now, does that make more sense?
soupmagnet said:
Try to understand what you're being told. I'm not saying anything about mounting your sdcard to transfer files to it so get that idea out of your head for a moment.
You need to boot into recovery and use the command 'adb push' to transfer a ROM to your sdcard, then flash it in recovery.
Now, does that make more sense?
Click to expand...
Click to collapse
I am attempting to understand what u are saying But I'm thinking ur not giving full step after step instructions OR this Version I have (v2.6.0.0) differs from Yours, Because there is No such OPTION as ADB PUSH..... I have ADB sideload (under Advanced Tab) which only wipes Cashe.. I've looked in every single area in TWRP and see nothing of anything You are talking about, other than "MOUNT" obviously.
soupmagnet said:
Try to understand what you're being told. I'm not saying anything about mounting your sdcard to transfer files to it so get that idea out of your head for a moment.
You need to boot into recovery and use the command 'adb push' to transfer a ROM to your sdcard, then flash it in recovery.
Now, does that make more sense?
Click to expand...
Click to collapse
While Searching Google for Help I seen this..> http://forum.xda-developers.com/showthread.php?t=2361144
I'm bout to install a Pc with Linux and try pushing it that way.. Have not tried that.
You don't need Linux to run adb commands *face palm* While I am a linux enthusiast, all he's trying to say is boot into twrp, plug kindle into your PC, and open a command prompt, CD into the directory of adb and run "adb push pathtofile /sdcard/filename" this should push it to the kindle, though their might be something else u need for in prior to this I'm not sure, soupemagnet will probably post back if there is. BTW I don't know if u actually meant u were going to install Linux, but if you don't plan on using it after this or anything in the case u do decide to still use it for this, u don't need to install it, distros like Ubuntu let you boot into a full os from the CD so u don't need to install it.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
stunts513 said:
You don't need Linux to run adb commands *face palm* While I am a linux enthusiast, all he's trying to say is boot into twrp, plug kindle into your PC, and open a command prompt, CD into the directory of adb and run "adb push pathtofile /sdcard/filename" this should push it to the kindle, though their might be something else u need for in prior to this I'm not sure, soupemagnet will probably post back if there is. BTW I don't know if u actually meant u were going to install Linux, but if you don't plan on using it after this or anything in the case u do decide to still use it for this, u don't need to install it, distros like Ubuntu let you boot into a full os from the CD so u don't need to install it.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
Stunt Thnx... You Helped breaking it down. I just used KFU and Fixed this within 3 minutes.. Thnx Man!:good:
hello, after some trouble installing the bootloader, I finally got it!!
But I have another problem, I thought it would start no problem then, so here I have no rom in sd!! and now will not start!
I can go into recovery mode, go to the usb storage option, but it does not work, I get on the computer!!
some way to spend a rom to the sd from l recovery / TWRP??????
Put the ROM and gapps in the same folder as an adb command, open a command prompt and CD to the directory with adb, now type something along the lines of this: adb push romname.zip /sdcard/
That should put the ROM on the sdcard so you can flash, use same thing for gapps as well.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
stunts513 said:
Put the ROM and gapps in the same folder as an adb command, open a command prompt and CD to the directory with adb, now type something along the lines of this: adb push romname.zip /sdcard/
That should put the ROM on the sdcard so you can flash, use same thing for gapps as well.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
thank you!
the problem is that now ADB does not recognize the tablet.
In device manager, I get the yellow triangle on kindle fire.
Reinstall the SDK but nothing, still without recognizing
EDIT I finally got it! you saved my life!! thank you very much!!