I'm trying a project on a Kindle Fire that I cannot afford to brick. To make it work I need to extract the initramfs. It seems that the format of the boot.img of custom ROMs for the device is not the same as mkbootimg images (and the stock image) It says
Code:
File boot.img not a plain boot image, seeking for embedded image ... not found.
with the CyanogenMod image but with the stock boot.img it works.. How can I get the initramfs from the boot.img?
You have to kill the non standard header with "dd if=boot.img of=boot2.img skip=1024” then run it on the boot2.img, I think that was the right skip count for the cm version, though this is pointless because if you recompile it then it is not going to work when you flash it, it will probably kick into fastboot or recovery with the kernel like that.
Sent from my Amazon Kindle Fire HD using Tapatalk
stunts513 said:
You have to kill the non standard header with "dd if=boot.img of=boot2.img skip=1024” then run it on the boot2.img, I think that was the right skip count for the cm version, though this is pointless because if you recompile it then it is not going to work when you flash it, it will probably kick into fastboot or recovery with the kernel like that.
Sent from my Amazon Kindle Fire HD using Tapatalk
Click to expand...
Click to collapse
Thanks, will try it once back in Linux.
It is not pointless because I need to get the initramfs. I want to try something: I'm gonna boot CM without flashing! (or fail badly )
How do you boot cm without flashing it? Otg?
Sent from my Amazon Kindle Fire HD using Tapatalk
chroot
stunts513 said:
How do you boot cm without flashing it? Otg?
Sent from my Amazon Kindle Fire HD using Tapatalk
Click to expand...
Click to collapse
It worked on my Debian system with Android-x86:
Code:
chroot /android /init
Basically I extract the initramfs , build the system folder (by reading the updater-script manually - done) and mount the initramfs in /android, the system in /android/system, the data in /android/data, the cache in /android/cache, start the chroot...
CM!!!
Interesting, is this like kexec? Or more like a ROM slot?or simply a virtual environment? Sorry for all the questions but this has peaked my curiosity a bit.
Sent from my Amazon Kindle Fire HD using Tapatalk
chroot
stunts513 said:
Interesting, is this like kexec? Or more like a ROM slot?or simply a virtual environment? Sorry for all the questions but this has peaked my curiosity a bit.
Sent from my Amazon Kindle Fire HD using Tapatalk
Click to expand...
Click to collapse
No, keep on being curious!
Basically a chroot (change root) is a way of making a process think that the root location is different. When you boot Android your initramfs is in /. We want a new one in /android but Android wants it to be /. We use a chroot so it thinks /android is /. Then init is happy and runs! kexec would require flashing a kernel and it is native and not a VM. What is a ROM slot?
Anyway, here is another example of a chroot (using VNC rather than native display and for desktop ARM Linux)
http://androlinux.com/
Remember, chroot is:
Native and fast
Just a way of tricking userspace programs
It is not:
Virtualization
A way of executing kernels
By the way, sorry for the delays - am working on a private project
Anyway, if I get somewhere I will start up a DevDB project. When I tried with the Amazon OS initramfs it just crashed - as expected. But now we should have CM initramfs...
This should hopefully ease people into the world of Cyanogen. I could write an app to safely install CM (chroot method) and when they are happy, it can flash it over (and keep their data).
OK I knew what chroot did but I didn't think of using it in that context before. That's pretty cool. Only times I ever really have to use chroot is when I mess up my grub config and have to chroot among other things into my own partition to update-grub. Also interesting that kexec involves kernel flashing, I thought it was just a kernel module that was loaded up from the modules folder(or whatever it was named I'm half asleep right now).
Sent from my Amazon Kindle Fire HD using Tapatalk
stunts513 said:
OK I knew what chroot did but I didn't think of using it in that context before. That's pretty cool. Only times I ever really have to use chroot is when I mess up my grub config and have to chroot among other things into my own partition to update-grub. Also interesting that kexec involves kernel flashing, I thought it was just a kernel module that was loaded up from the modules folder(or whatever it was named I'm half asleep right now).
Sent from my Amazon Kindle Fire HD using Tapatalk
Click to expand...
Click to collapse
It needs kernel flashing because the kernel isn't set up for modules
This will mean that CM modules won't work either when in chroot (same kernel)
Anyway, I'm "new" and must wait 5 minutes between each post :crying:
stunts513 said:
You have to kill the non standard header with "dd if=boot.img of=boot2.img skip=1024” then run it on the boot2.img, I think that was the right skip count for the cm version, though this is pointless because if you recompile it then it is not going to work when you flash it, it will probably kick into fastboot or recovery with the kernel like that.
Sent from my Amazon Kindle Fire HD using Tapatalk
Click to expand...
Click to collapse
Not the right skip
Code:
%Premature end-of-file saving zImage.
2 is the number.
saleemrashid1 said:
Not the right skip
Code:
%Premature end-of-file saving zImage.
Click to expand...
Click to collapse
It was 2!!! 2!!! 2!!! Not 1024, not 2048, not 512, not 256, not even 42! It was 2!!!
For future reference:
Code:
dd if=boot.img of=boot2.img skip=2
./unmkbootimg boot2.img
chrooting...
saleemrashid1 said:
It needs kernel flashing because the kernel isn't set up for modules
This will mean that CM modules won't work either when in chroot (same kernel)
Anyway, I'm "new" and must wait 5 minutes between each post :crying:
Click to expand...
Click to collapse
chroot started... (no crash but no adb )
We will just have to wait and see
saleemrashid1 said:
chroot started... (no crash but no adb )
We will just have to wait and see
Click to expand...
Click to collapse
It says
Code:
A N D R O I D _
then goes black
saleemrashid1 said:
It says
Code:
A N D R O I D _
then goes black
Click to expand...
Click to collapse
It doesn't go black, it actually turns off!
saleemrashid1 said:
It doesn't go black, it actually turns off!
Click to expand...
Click to collapse
I give up for now
Code:
<4>[ 1171.575317] Welcome
<6>[ 1188.026672] request_suspend_state: wakeup (3->0) at 1188017547609 (2014-04-10 13:32:06.608901123 UTC)
<6>[ 1188.073394] ***************************************************
<6>[ 1188.073394] ****************** Panel of LG ******************
<6>[ 1188.073425] ***************************************************
<6>[ 1188.077606] bq27541 1-0055: Screen off drainage: -3 % over 813945 msecs
<6>[ 1188.077606] DSSCOMP: dsscomp_late_resume
<4>[ 1188.126373] ilitek_i2c_late_resume
<3>[ 1188.242858] omap_timer omap_timer.10: omap2_dm_timer_set_src: clk_set_parent() to sys_ck FAILED
<3>[ 1191.694305] init: untracked pid 357 exited
<3>[ 1191.694366] init: untracked pid 372 exited
<3>[ 1191.694427] init: untracked pid 418 exited
<3>[ 1191.695648] init: untracked pid 527 exited
<3>[ 1191.696563] init: untracked pid 1837 exited
<3>[ 1191.701385] init: untracked pid 347 exited
<3>[ 1191.718139] init: untracked pid 881 exited
<3>[ 1191.724578] init: untracked pid 267 exited
<3>[ 1191.727783] init: untracked pid 335 exited
<3>[ 1191.728210] init: untracked pid 182 exited
<3>[ 1191.730285] init: untracked pid 256 exited
<3>[ 1191.734802] init: untracked pid 808 exited
<3>[ 1191.737548] init: untracked pid 281 exited
<3>[ 1191.740173] init: untracked pid 795 exited
<3>[ 1191.742828] init: untracked pid 322 exited
<3>[ 1191.750823] init: untracked pid 697 exited
<3>[ 1191.757995] init: untracked pid 391 exited
<3>[ 1191.758056] init: untracked pid 473 exited
<3>[ 1191.764221] init: untracked pid 447 exited
<3>[ 1191.764923] init: untracked pid 432 exited
<3>[ 1191.770507] init: untracked pid 577 exited
<3>[ 1191.774261] init: untracked pid 1698 exited
<3>[ 1191.777740] init: untracked pid 460 exited
<3>[ 1191.781341] init: untracked pid 1595 exited
<3>[ 1191.784088] init: untracked pid 588 exited
<3>[ 1191.785797] init: untracked pid 1488 exited
<3>[ 1191.791168] init: untracked pid 674 exited
<3>[ 1191.794555] init: untracked pid 754 exited
<3>[ 1191.797088] init: untracked pid 1310 exited
<3>[ 1191.803131] init: untracked pid 833 exited
<3>[ 1191.809692] init: untracked pid 979 exited
<3>[ 1191.823486] init: untracked pid 1095 exited
<3>[ 1191.825775] init: untracked pid 1251 exited
<3>[ 1191.828369] init: untracked pid 1638 exited
<3>[ 1191.832824] init: untracked pid 2090 exited
<3>[ 1191.836303] init: untracked pid 2114 exited
<3>[ 1191.839080] init: untracked pid 1921 exited
<3>[ 1191.842285] init: untracked pid 1820 exited
<3>[ 1191.849182] init: untracked pid 1651 exited
<3>[ 1191.853942] init: untracked pid 1749 exited
<3>[ 1191.854492] init: untracked pid 2056 exited
<3>[ 1191.857666] init: untracked pid 2402 exited
<3>[ 1191.861816] init: untracked pid 2492 exited
<3>[ 1191.864776] init: untracked pid 1792 exited
<6>[ 1194.908813] mtp_release
<6>[ 1195.877410] alarm_release: clear alarm, pending 0
<6>[ 1195.877441] alarm_release: clear alarm, pending 0
<6>[ 1195.877441] alarm_release: clear alarm, pending 0
<6>[ 1195.877441] alarm_release: clear alarm, pending 0
<3>[ 1232.477325] init: could not import file '/init.omap4blazeboard.rc' from '/init.rc'
<3>[ 1232.477752] init: could not import file '/init.carrier.rc' from '/init.rc'
<3>[ 1232.479125] init: do_chown: Could not access /selinux/booleans
<3>[ 1232.479187] init: do_chown: Could not access /sys/fs/selinux/booleans
<3>[ 1232.611175] init: cannot open '/initlogo.rle'
<3>[ 1232.631896] init: cannot find '/system/bin/auditd', disabling 'auditd'
<3>[ 1232.632446] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
<6>[ 1232.635894] adb_release
<6>[ 1232.636199] adb_open
<6>[ 1232.647277] adb_release
<6>[ 1232.647460] adb_open
<3>[ 1232.650787] init: untracked pid 2624 exited
<3>[ 1232.697387] init: untracked pid 2637 exited
<3>[ 1233.638092] init: untracked pid 1972 exited
<3>[ 1237.851593] init: untracked pid 2643 exited
<3>[ 1237.854003] init: untracked pid 2996 exited
<3>[ 1237.868988] init: untracked pid 3000 exited
<3>[ 1242.880950] init: untracked pid 3005 exited
<3>[ 1242.885925] init: untracked pid 3014 exited
<3>[ 1244.220550] init: untracked pid 3017 exited
<3>[ 1244.236663] init: untracked pid 2999 exited
<3>[ 1244.236907] init: untracked pid 2622 exited
<3>[ 1244.244384] init: untracked pid 3018 exited
<6>[ 1244.244659] request_suspend_state: wakeup (0->0) at 1244235565188 (2014-04-10 13:33:02.826918702 UTC)
<3>[ 1244.246551] init: untracked pid 2619 exited
<3>[ 1244.251922] init: untracked pid 2636 exited
<3>[ 1247.270416] init: untracked pid 3378 exited
<6>[ 1247.806610] request_suspend_state: wakeup (0->0) at 1247797515872 (2014-04-10 13:33:06.388869386 UTC)
<3>[ 1247.808471] init: untracked pid 3044 exited
<3>[ 1247.822265] init: untracked pid 3374 exited
<3>[ 1247.837799] init: untracked pid 3377 exited
<3>[ 1252.850189] init: critical process 'servicemanager' exited 4 times in 4 minutes; rebooting into recovery mode
<6>[ 1252.900482] SysRq : Emergency Remount R/O
https://gist.github.com/saleemrashid1/ffb5b24d55ce4050c3b9
Wait which kindle is this? Because the kf2 and kf2013 are 2 entirely different models. I interesting that the number was different though.
Sent from my Amazon Kindle Fire HD using Tapatalk
stunts513 said:
Wait which kindle is this? Because the kf2 and kf2013 are 2 entirely different models. I interesting that the number was different though.
Sent from my Amazon Kindle Fire HD using Tapatalk
Click to expand...
Click to collapse
Which number? Anyway it is otter2 (Kindle Fire 2)
OK that is very odd, I never asked hashcode the number for otter2's, I assumed it was the same. Weird.
Sent from my Amazon Kindle Fire HD using Tapatalk
Related
Hi,
a couple times a week my phone seems to freeze when I push the powerbutton. The hardware buttons light up, but the screen remains black. I always have to pull the battery, after that it works again.
I finally was near a pc when it happened and managed to make a dmesg log. This was taken while the phone wasn't responding. I just plugged it in and used adb to get a log. Here's the interesting part (at least I think it is):
Code:
<6>[ 5433.007232] bravo_ts_power: power 0
<7>[ 5433.007507] __capella_cm3602_power: Turn the capella_cm3602 power off
<6>[ 5433.008026] lcdc_suspend: suspending
<6>[ 5433.008331] [R] early_suspend: sync
<6>[ 5433.033782] active wake lock PowerManagerService
<6>[ 5433.033905] active wake lock SMD_DATA5, time left 21
<6>[ 5433.034149] active wake lock SMD_DS, time left 41
<6>[ 5433.034332] [R] early_suspend end
<3>[ 5438.615905] mmc1: Data CRC error
<3>[ 5438.616729] msmsdcc_data_err: opcode 0x00000019
<3>[ 5438.617156] msmsdcc_data_err: blksz 512, blocks 5
<3>[ 5438.618194] mmcblk0: error -84 transferring data, sector 1668966, nr 5, card status 0xf00
<3>[ 5438.620758] mmc1: Data timeout
<3>[ 5438.621612] end_request: I/O error, dev mmcblk0, sector 1668966
<3>[ 5438.622070] Buffer I/O error on device mmcblk0p1, logical block 1668965
<4>[ 5438.622833] lost page write due to I/O error on mmcblk0p1
<3>[ 5438.623291] end_request: I/O error, dev mmcblk0, sector 1668967
<3>[ 5438.624053] Buffer I/O error on device mmcblk0p1, logical block 1668966
<4>[ 5438.624511] lost page write due to I/O error on mmcblk0p1
<3>[ 5438.625305] end_request: I/O error, dev mmcblk0, sector 1668968
<3>[ 5438.625762] Buffer I/O error on device mmcblk0p1, logical block 1668967
<4>[ 5438.626525] lost page write due to I/O error on mmcblk0p1
<3>[ 5438.626983] end_request: I/O error, dev mmcblk0, sector 1668969
<3>[ 5438.627746] Buffer I/O error on device mmcblk0p1, logical block 1668968
<4>[ 5438.628173] lost page write due to I/O error on mmcblk0p1
<3>[ 5438.628967] end_request: I/O error, dev mmcblk0, sector 1668970
<3>[ 5438.629394] Buffer I/O error on device mmcblk0p1, logical block 1668969
<4>[ 5438.630187] lost page write due to I/O error on mmcblk0p1
<3>[ 5443.042205] mmcblk0: error -110 sending read/write command, response 0x920, card status 0x400900
<3>[ 5443.043090] mmc1: Data timeout
<3>[ 5443.043884] end_request: I/O error, dev mmcblk0, sector 1669055
<3>[ 5443.044311] Buffer I/O error on device mmcblk0p1, logical block 1669054
<4>[ 5443.045104] lost page write due to I/O error on mmcblk0p1
<3>[ 5443.045562] end_request: I/O error, dev mmcblk0, sector 1669056
<3>[ 5443.046325] Buffer I/O error on device mmcblk0p1, logical block 1669055
<4>[ 5443.046752] lost page write due to I/O error on mmcblk0p1
<3>[ 5443.047546] end_request: I/O error, dev mmcblk0, sector 1669057
<3>[ 5443.047973] Buffer I/O error on device mmcblk0p1, logical block 1669056
<4>[ 5443.048736] lost page write due to I/O error on mmcblk0p1
<3>[ 5443.049194] end_request: I/O error, dev mmcblk0, sector 1669058
<3>[ 5443.049987] Buffer I/O error on device mmcblk0p1, logical block 1669057
<4>[ 5443.050415] lost page write due to I/O error on mmcblk0p1
<3>[ 5443.051208] end_request: I/O error, dev mmcblk0, sector 1669059
<3>[ 5443.051635] end_request: I/O error, dev mmcblk0, sector 1669067
<3>[ 5443.052429] end_request: I/O error, dev mmcblk0, sector 1669075
<3>[ 5443.052856] end_request: I/O error, dev mmcblk0, sector 1669083
<3>[ 5443.053649] end_request: I/O error, dev mmcblk0, sector 1669091
<3>[ 5443.054077] end_request: I/O error, dev mmcblk0, sector 1669099
<3>[ 5443.054870] end_request: I/O error, dev mmcblk0, sector 1669107
<3>[ 5443.055664] end_request: I/O error, dev mmcblk0, sector 1669115
<3>[ 5443.056091] end_request: I/O error, dev mmcblk0, sector 1669123
<3>[ 5443.056884] end_request: I/O error, dev mmcblk0, sector 1669131
<3>[ 5443.057312] end_request: I/O error, dev mmcblk0, sector 1669139
<3>[ 5443.058105] end_request: I/O error, dev mmcblk0, sector 1669147
<3>[ 5443.058563] end_request: I/O error, dev mmcblk0, sector 1669155
<3>[ 5443.059326] end_request: I/O error, dev mmcblk0, sector 1669163
<3>[ 5443.059783] end_request: I/O error, dev mmcblk0, sector 1669171
<3>[ 5443.060546] end_request: I/O error, dev mmcblk0, sector 1669179
<3>[ 5443.066314] mmcblk0: error -110 sending read/write command, response 0x920, card status 0x400900
<3>[ 5443.067199] mmc1: Data timeout
<3>[ 5443.067626] end_request: I/O error, dev mmcblk0, sector 2112723
<3>[ 5443.068420] Buffer I/O error on device mmcblk0p1, logical block 2112722
<4>[ 5443.068847] lost page write due to I/O error on mmcblk0p1
<3>[ 5443.074676] mmcblk0: error -110 sending read/write command, response 0x920, card status 0x400900
<3>[ 5443.075653] mmc1: Data timeout
<3>[ 5443.076110] end_request: I/O error, dev mmcblk0, sector 2
<3>[ 5443.081573] mmcblk0: error -110 sending read/write command, response 0x920, card status 0x400900
<3>[ 5443.082427] mmc1: Data timeout
<3>[ 5443.082855] end_request: I/O error, dev mmcblk0, sector 833
<3>[ 5443.088745] mmcblk0: error -110 sending read/write command, response 0x920, card status 0x400900
<3>[ 5443.089599] mmc1: Data timeout
<3>[ 5443.090026] end_request: I/O error, dev mmcblk0, sector 15594
<3>[ 5443.483581] mmc1: Data CRC error
<3>[ 5443.484374] msmsdcc_data_err: opcode 0x00000011
<3>[ 5443.484802] msmsdcc_data_err: blksz 512, blocks 1
<3>[ 5443.485748] mmcblk0: error -84 transferring data, sector 833, nr 1, card status 0xb00
<3>[ 5443.486389] end_request: I/O error, dev mmcblk0, sector 833
<3>[ 5443.487609] FAT: FAT read failed (blocknr 832)
<3>[ 5443.488616] mmc1: DMA channel flushed (0x80000004)
<3>[ 5443.489410] Flush data: 0000c003 3b18e000 00000000 00400040 00050004 00004003
<6>[ 5480.704193] batt: 95%, 4030 mV, -119 mA (-215 avg), 23.6 C, 1275 mAh
<6>[ 5530.876739] batt: 95%, 4030 mV, -69 mA (-82 avg), 23.6 C, 1273 mAh
<6>[ 5563.668518] gpio_keys_scan_keys: key 1-74, 0 (94) changed to 1
<6>[ 5563.673858] request_suspend_state: wakeup (3->0) at 5555550724239 (2010-12-28 12:24:48.362411743 UTC)
<6>[ 5563.674713] [R] late_resume start
<6>[ 5563.675201] lcdc_resume: resuming
<6>[ 5563.675628] samsung_oled_panel_init: +()
<6>[ 5563.676788] samsung_oled_panel_init: -()
<6>[ 5563.677368] msmfb: ready, waiting for full update
<7>[ 5563.678131] __capella_cm3602_power: Turn the capella_cm3602 power on
<6>[ 5563.678955] bravo_ts_power: power 1
<6>[ 5563.680053] lightsensor_ioctl set value = 1
<6>[ 5563.680816] lightsensor_enable
After that I reformatted my SDcard, wiped everything and did a fresh install of CM instead of Oxygen RC4 which I was using before.
Today I was downloading a few apps from the market, when suddenly the downloads disappeared from the notification bar. I used quick system info to look at the logs (again only a small part, i still have the rest if the full log contains more useful information):
Code:
<3> [23578.803039] : mmc1: Data CRC error
<3> [23578.803466] : msmsdcc_data_err: opcode 0x00000019
<3> [23578.804229] : msmsdcc_data_err: blksz 512, blocks 49
<3> [23578.804657] : mmc1: DMA channel flushed (0x80000004)
<3> [23578.805084] : Flush data: 0000c003 3b252030 00000000 00400040 00170015 00008003
<3> [23578.810241] : mmcblk0: error -84 transferring data, sector 2556870, nr 49, card status 0x900
<3> [23578.811096] : mmc1: Data timeout
<3> [23578.811889] : end_request: I/O error, dev mmcblk0, sector 2556870
<3> [23578.812652] : end_request: I/O error, dev mmcblk0, sector 2556878
<3> [23578.813079] : end_request: I/O error, dev mmcblk0, sector 2556886
<3> [23578.813812] : end_request: I/O error, dev mmcblk0, sector 2556894
<3> [23578.814209] : end_request: I/O error, dev mmcblk0, sector 2556902
<3> [23578.814972] : end_request: I/O error, dev mmcblk0, sector 2556910
<3> [23578.815368] : end_request: I/O error, dev mmcblk0, sector 2556918
<3> [23578.821869] : mmcblk0: error -110 sending read/write command, response 0x920, card status 0x400900
<3> [23578.823883] : mmc1: Data timeout
<3> [23578.824524] : end_request: I/O error, dev mmcblk0, sector 2556934
<3> [23578.830535] : mmcblk0: error -110 sending read/write command, response 0x920, card status 0x400900
<3> [23578.832946] : mmc1: Data timeout
<3> [23578.833801] : end_request: I/O error, dev mmcblk0, sector 2049
<3> [23578.834564] : Buffer I/O error on device mmcblk0p1, logical block 1
<4> [23578.834991] : lost page write due to I/O error on mmcblk0p1
<3> [23578.844360] : mmcblk0: error -110 sending read/write command, response 0x920, card status 0x400900
<3> [23578.844635] : mmc1: Data timeout
<3> [23578.844757] : end_request: I/O error, dev mmcblk0, sector 4515
<3> [23578.844879] : Buffer I/O error on device mmcblk0p1, logical block 2467
<4> [23578.845092] : lost page write due to I/O error on mmcblk0p1
<3> [23579.089599] : mmc1: Data CRC error
<3> [23579.090057] : msmsdcc_data_err: opcode 0x00000011
<3> [23579.090454] : msmsdcc_data_err: blksz 512, blocks 1
<3> [23579.091919] : mmcblk0: error -84 transferring data, sector 4515, nr 1, card status 0xb00
<3> [23579.092315] : end_request: I/O error, dev mmcblk0, sector 4515
<3> [23579.093231] : FAT: FAT read failed (blocknr 2467)
<3> [23579.098968] : mmcblk0: error -110 sending read/write command, response 0xb00, card status 0x400b00
<3> [23579.105072] : end_request: I/O error, dev mmcblk0, sector 63598
<3> [23579.105529] : Buffer I/O error on device mmcblk0p1, logical block 61550
<4> [23579.105926] : lost page write due to I/O error on mmcblk0p1
<3> [23579.582916] : FAT: Filesystem error (dev mmcblk0p1)
<3> [23579.583038] : fat_get_cluster: invalid cluster chain (i_pos 984821)
<3> [23579.583465] : FAT: Filesystem has been set read-only
<6> [23585.658355] : wake lock SMD_DATA5, expired
<7> [23585.663910] : save exit: isCheckpointed 1
<6> [23585.666900] : suspend: enter suspend
<6> [23585.667297] : PM: Syncing filesystems ... done.
<4> [23585.670532] : Freezing user space processes ... (elapsed 0.02 seconds) done.
<4> [23585.699371] : Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
<6> [23585.749786] : PM: suspend of devices complete after 28.841 msecs
<6> [23585.750854] : power_suspend_late return 0
<6> [23585.751281] : PM: late suspend of devices complete after 1.036 msecs
<6> [23585.751281] : clocks on: uart_clk
<6> [23585.751281] : [R] suspend end
<6> [23585.751281] : [R] resume start
<6> [23585.751678] : PM: early resume of devices complete after 0.396 msecs
<6> [23585.757965] : wakeup wake lock: SMD_RPCCALL
<6> [23585.764862] : PM: resume of devices complete after 12.439 msecs
<4> [23585.766082] : Restarting tasks ... done.
<6> [23585.783905] : suspend: exit suspend, ret = 0 (2010-12-29 13:37:55.798841765 UTC)
<6> [23585.784912] : active wake lock ds2784-battery
<6> [23585.785339] : suspend: abort suspend
Could the freeze be the result of having apps installed on the SD when the error occurred?
The strange thing is that I got a new SD card for Christmas, and I have had (seemingly) the same freezes before. I never managed to get a log before, since i was never near a computer.
I already tried reformatting the card a few times, but that didn't seem to help.
Does anybody know a solution? Is it SD card related, or can it be caused by something else entirely?
Thanks
Does anyone have know if this is a problem with my SD card?
I find it odd that I also had the lockscreen freezing on my other SD card, I don't have it with me at the moment, so I can't compare the logs.
Is it also possible that the internal memory is corrupt? (Which would be a lot worse i guess )
Are you overclocking? If your min cpu speed is lower that 245mhz sometimes you get issues with the device waking.
Sent from my HTC Desire using Tapatalk
No, I'm not over/underclocking.
The second log was taken after several failed downloads of updates from the market. It showed the exact same error as the one were the lockscreen froze, but the phone functioned normally. Except for the downloads that failed of course.
I think the freezing is the result of an app or essential file on the SD card that can't be reached. Is that possible?
I have the same problem with the screen not waking. Did you find a solution?
Exact same problem..!!
Hey,
I have the exact same problem! I'm running a mildwild rom, with cm7r2 hboot, and 4ext recovery.. everything should be OK, but it's not..
I also think that it's the SD card that's dying.. gonna buy a new one tomorrow, and see if the problem goes away.. I'll post here, as soon as I find something out..!
- H
Is it a class 10 card? Also, maybe the I/O schedule may cause it.
What settings do u have set for it?
SaySayonara said:
Is it a class 10 card? Also, maybe the I/O schedule may cause it.
What settings do u have set for it?
Click to expand...
Click to collapse
Hey,
No I don't think it is.. but I don't think that should matter much, since I just got this phone, and had an old SD-card lying around.. so I rooted it, partitioned it, etc., but these malfunctions appeared almost immediately.. and I'm pretty sure the SD was OK when I put it in.. isn't class 10 usually only recommended for demanding a2sd setup-ups, that run over long periods of time..? I find it extremly suspicious that an SD card, even below class 6, would almost instantaneously die upon being put into use.. ?
However, now I've played around with it some more, and I'm almost certain now that it's the SD card that has gone broken.. because if I clear the data and cache of both google play and google framework services apks, and then boot into recovery and choose "tools" --> "check filesystem" --> sdcard --> repair sdcard (it doesn't work EVERY time, which also makes me suspect the Sd card...!!!!) , and then reboot, the SD card will work -- for a while... Like, I'll install 5-7 apps from google play, and then the same s**t all over again..
Gonna try it out with the same setup, but a brand new class 10 SD tomorrow, and report back..!
- H
I bought Sandisk Extreme 32GB
What partitioning tool did u use? I've seen many ppl saying that 4ext is the best. To be Frank I never had any issues with it.
SaySayonara said:
I bought Sandisk Extreme 32GB
What partitioning tool did u use? I've seen many ppl saying that 4ext is the best. To be Frank I never had any issues with it.
Click to expand...
Click to collapse
Yeah, I also used 4ext.. worked like a charm!
HAhaha, LOL - I was just looking at what card I'm gonna get tomorrow, and it looks like it's gonna be the same as yours..!!
- H
You're in for a treat my friend
I was very surprised by the difference.
All right!
The mystery is solved! Just tested it out with a new SanDisk class 10 16GB SD card.. everything works just fine.. partitioned it in 4ext, installed MildWild AOSP GB rom, installed a s**tload of apps, and everything works just fine.. the a2sd script is working as it should, both the rom install and apps install went smoothly. Besides changing the SD card, I changed nothing; same HBOOT, same 4ext, same everything.. So I guess it was the SD card that was fu***n things up..!
Cheers everybody!
- H
I have had my refurbished HTC Vision for about three weeks and it hadn't had any problems. Then yesterday, I rebooted it and now the sdcard doesn't work. Not just that it doesn't mount, rather there is not even a /dev/block/mmcblk1 device.
Here is what I tried:
* Boot into ClockworkMod, and run adb shell. Still no /dev/block/mmcblk1.
* Boot into fastboot and run "fastboot oem enableqxdm 0" and "fastboot oem eraseconfig".
* Per some random instructions on the net, I held vol-up and power, then pulled the battery after the phone vibrated. Then I held vol-up, vol-down, power and did the same. Then the fastboot commands again.
* Bent the sdcard port's pins out a bit with tweezers.
* SDcard works in computer (Linux).
* Tried another card that has nothing but a vfat partition.
Nothing works! There are some errors in dmesg:
Code:
$ dmesg |grep mmc
<5>[ 0.000000] Kernel command line: board_vision.disable_uart2=0 board_vision.usb_h2w_sw=0 board_vision.disable_sdcard=0 diag.enabled=0 board_vision.debug_uart=0 smisize=0 userdata_sel=0 androidboot.emmc=true androidboot.baseband=26.02.01.15_M2 androidboot.cid=T-MOB010 androidboot.batt_poweron=good_battery androidboot.carrier=TMUS androidboot.mid=PC1010000 androidboot.keycaps=qwerty androidboot.mode=normal androidboot.serialno=HT09LR200858 androidboot.bootloader=0.76.2000 no_console_suspend=1 console=null
<6>[ 2.532989] vision: vision_init_mmc
<3>[ 3.267822] mmc0: No card detect facilities available
<6>[ 3.268341] mmc0: Qualcomm MSM SDCC at 0x00000000a0500000 irq 98,0 dma 7
<6>[ 3.268615] mmc0: Platform slot type: MMC
<6>[ 3.268737] mmc0: 4 bit data mode disabled
<6>[ 3.269012] mmc0: 8 bit data mode enabled
<6>[ 3.269134] mmc0: MMC clock 144000 -> 50000000 Hz, PCLK 96000000 Hz
<6>[ 3.269378] mmc0: Slot eject status = 0
<6>[ 3.269531] mmc0: Power save feature enable = 1
<6>[ 3.269653] mmc0: DM non-cached buffer at ffa0c000, dma_addr 0x2b774000
<6>[ 3.269927] mmc0: DM cmd busaddr 0x2b774000, cmdptr busaddr 0x2b774300
<6>[ 3.270751] mmc1: Qualcomm MSM SDCC at 0x00000000a3000000 irq 96,0 dma 8
<6>[ 3.270996] mmc1: Platform slot type: N/A
<6>[ 3.271148] mmc1: 4 bit data mode enabled
<6>[ 3.271392] mmc1: 8 bit data mode disabled
<6>[ 3.271514] mmc1: MMC clock 144000 -> 50000000 Hz, PCLK 96000000 Hz
<6>[ 3.271789] mmc1: Slot eject status = 1
<6>[ 3.271911] mmc1: Power save feature enable = 1
<6>[ 3.272064] mmc1: DM non-cached buffer at ffa0d000, dma_addr 0x2b777000
<6>[ 3.272308] mmc1: DM cmd busaddr 0x2b777000, cmdptr busaddr 0x2b777300
<6>[ 3.273468] mmc2: Qualcomm MSM SDCC at 0x00000000a3100000 irq 100,0 dma 8
<6>[ 3.273712] mmc2: Platform slot type: SD
<6>[ 3.273834] mmc2: 4 bit data mode enabled
<6>[ 3.273986] mmc2: 8 bit data mode disabled
<6>[ 3.274230] mmc2: MMC clock 144000 -> 50000000 Hz, PCLK 96000000 Hz
<6>[ 3.274353] mmc2: Slot eject status = 0
<6>[ 3.274658] mmc2: Power save feature enable = 1
<6>[ 3.274810] mmc2: DM non-cached buffer at ffa0e000, dma_addr 0x2b778000
<6>[ 3.275054] mmc2: DM cmd busaddr 0x2b778000, cmdptr busaddr 0x2b778300
<6>[ 3.275207] mmc2: Polling status mode enabled
<6>[ 3.425598] mmc0: new high speed MMC card at address 0001
<6>[ 3.427093] mmcblk0: mmc0:0001 SEM04G 2.09 GiB
<6>[ 3.428100] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 >
<6>[ 3.569030] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts: barrier=1
<4>[ 3.703063] mmc2: high speed mode max_dtr = 50000000
<4>[ 3.703491] mmc2: host does not support reading read-only switch. assuming write-enable.
<6>[ 3.703643] mmc2: new high speed SDHC card at address 0001
<6>[ 3.704498] mmcblk1: mmc2:0001 00000 7.41 GiB
<6>[ 3.705291] mmcblk1: p1
<4>[ 4.648254] EXT4-fs (mmcblk0p26): warning: maximal mount count reached, running e2fsck is recommended
<7>[ 4.651062] EXT4-fs (mmcblk0p26): ext4_orphan_cleanup: deleting unreferenced inode 24790
<7>[ 4.655670] EXT4-fs (mmcblk0p26): ext4_orphan_cleanup: deleting unreferenced inode 24741
<6>[ 4.657012] EXT4-fs (mmcblk0p26): 2 orphan inodes deleted
<6>[ 4.657379] EXT4-fs (mmcblk0p26): recovery complete
<6>[ 4.703216] EXT4-fs (mmcblk0p26): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<4>[ 4.758331] EXT4-fs (mmcblk0p27): warning: maximal mount count reached, running e2fsck is recommended
<6>[ 4.760345] EXT4-fs (mmcblk0p27): recovery complete
<6>[ 4.762298] EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts: barrier=1
<4>[ 4.886474] EXT4-fs (mmcblk0p28): warning: maximal mount count reached, running e2fsck is recommended
<6>[ 4.888580] EXT4-fs (mmcblk0p28): recovery complete
<6>[ 4.890563] EXT4-fs (mmcblk0p28): mounted filesystem with ordered data mode. Opts: barrier=1
<7>[ 20.824981] mmc1: card_present 1
<6>[ 20.825134] mmc1: Slot status change detected (0 -> 1)
<7>[ 23.383300] mmc1: queuing CIS tuple 0x91 length 3
<6>[ 23.383331] mmc1: new high speed SDIO card at address 0001
<3>[ 38.746368] mmc2: Data CRC error
<6>[ 38.746978] mmc2: Controller has been reset
<3>[ 38.747467] mmcblk1: error -84 transferring data, sector 2080, nr 1, card status 0x900
<6>[ 38.747619] mmc2: reinit card
<4>[ 38.747863] mmc2: Starting deferred resume
<3>[ 38.814849] mmc2: Data CRC error
<6>[ 38.815521] mmc2: Controller has been reset
<3>[ 38.815856] mmc2: Re-init card rc = -84 (retries = 5)
<3>[ 38.997650] mmc2: Data CRC error
<6>[ 38.998291] mmc2: Controller has been reset
<3>[ 39.001403] mmc2: Re-init card rc = -84 (retries = 4)
<3>[ 39.200927] mmc2: Data CRC error
<6>[ 39.201507] mmc2: Controller has been reset
<3>[ 39.201721] mmc2: Re-init card rc = -84 (retries = 3)
<3>[ 39.384826] mmc2: Data CRC error
<6>[ 39.385406] mmc2: Controller has been reset
<3>[ 39.385650] mmc2: Re-init card rc = -84 (retries = 2)
<3>[ 39.583618] mmc2: Data CRC error
<6>[ 39.584228] mmc2: Controller has been reset
<3>[ 39.584472] mmc2: Re-init card rc = -84 (retries = 1)
<6>[ 39.666137] mmc2: Deferred resume failed
<6>[ 39.666412] mmc: reinit failed, remove card
<6>[ 39.666625] mmc2: remove card
<3>[ 39.666778] end_request: I/O error, dev mmcblk1, sector 2080
<3>[ 39.667053] Buffer I/O error on device mmcblk1p1, logical block 32
<4>[ 39.667205] lost page write due to I/O error on mmcblk1p1
<3>[ 39.667480] mmc_blk_issue_rq failed!!
<6>[ 39.667633] mmc2: mmc_remove_sd_card
<6>[ 39.667907] mmc2: card 0001 removed
<3>[ 39.670318] mmcblk1: error -123 sending status comand
<3>[ 39.670471] mmcblk1: error -123 sending read/write command, response 0x0, card status 0x0
<3>[ 39.670867] end_request: I/O error, dev mmcblk1, sector 2080
<3>[ 39.671783] mmc_blk_issue_rq failed!!
<3>[ 39.671966] mmcblk1: error -123 sending read command, response 0x0
<4>[ 39.672210] mmcblk1: retrying using single block read
<3>[ 39.672332] mmcblk1: error -123 sending status comand
<3>[ 39.672607] mmcblk1: error -123 sending read/write command, response 0x0, card status 0x0
<3>[ 39.672882] end_request: I/O error, dev mmcblk1, sector 32378
<3>[ 39.673126] end_request: I/O error, dev mmcblk1, sector 32379
<3>[ 39.673278] end_request: I/O error, dev mmcblk1, sector 32380
<3>[ 39.673522] end_request: I/O error, dev mmcblk1, sector 32381
<3>[ 39.673675] end_request: I/O error, dev mmcblk1, sector 32382
<3>[ 39.673919] end_request: I/O error, dev mmcblk1, sector 32383
<3>[ 39.674072] end_request: I/O error, dev mmcblk1, sector 32384
<3>[ 39.674316] end_request: I/O error, dev mmcblk1, sector 32385
<3>[ 39.674499] mmc_blk_issue_rq failed!!
<3>[ 39.674774] mmcblk1: error -123 sending status comand
<3>[ 39.674926] mmcblk1: error -123 sending read/write command, response 0x0, card status 0x0
<3>[ 39.675292] end_request: I/O error, dev mmcblk1, sector 32378
... and so on. In this run, I see that at least briefly the kernel could read the mmcblk1 partition table (although there still was not /dev/block/mmcblk1). However, most of the time it can't and just gives the CRC errors.
Is this a hardware or software problem. Any suggestions? Thanks.
Almost 100% hardware from what you have written, I would suggest disconnecting the ribbion cable, clean it, and put it back. If it still won't work a new sd card tray is about 10$ on ebay and a snap to put it
Sent from my HTC Vision using xda premium
worked!
demkantor said:
Almost 100% hardware from what you have written, I would suggest disconnecting the ribbion cable, clean it, and put it back. If it still won't work a new sd card tray is about 10$ on ebay and a snap to put it
Sent from my HTC Vision using xda premium
Click to expand...
Click to collapse
Worked, thanks!!! The CRC errors made me suspect hardware, but I wanted someone else to say it before I tore the thing open. I've always had bad luck tearing these things apart (only junk phones in the past), but I bought a cheapo disassembly kit a while back which has helped greatly with popping the case off. And thankfully I only had to get to about step three of the instructions before the ribbon cable was accessible!
Hi. I have Nexus 7 2013 WiFi 32Gb. FLO 04.02 bootloader. Stock 4.4.2 android with root and teamwin.
Recently, I start download file and after that my nexus 7 rebooted. And it stuck on Google boot screen. I try to run teamwin, but it also stuck on Teamwin logo.
In fastboot mode i get:
Code:
> sudo fastboot -u format cache
formatting 'cache' partition...
Creating filesystem with parameters:
Size: 587202560
Block size: 4096
Blocks per group: 32768
Inodes per group: 7168
Inode size: 256
Journal blocks: 2240
Label:
Blocks: 143360
Block groups: 5
Reserved block group size: 39
Created filesystem with 11/35840 inodes and 4616/143360 blocks
sending 'cache' (10984 KB)...
writing 'cache'...
FAILED (remote: flash write failure)
finished. total time: 89.945s
> sudo fastboot -w
erasing 'userdata'...
FAILED (remote: failed to erase partition)
finished. total time: 0.015s
> sudo fastboot flash bootloader bootloader-flo-flo-04.02.img
sending 'bootloader' (3911 KB)...
OKAY [ 0.130s]
writing 'bootloader'...
FAILED (remote: flash write failure)
finished. total time: 1.068s
e2fsck:
Code:
e2fsck /dev/block/mmcblk0
e2fsck 1.41.14 (22-Dec-2010)
e2fsck: Device or resource busy while trying to open /dev/block/mmcblk0
Filesystem mounted or opened exclusively by another program?
e2fsck 1.41.14 (22-Dec-2010)
e2fsck: Device or resource busy while trying to open /dev/block/mmcblk0p30
Filesystem mounted or opened exclusively by another program?
mount:
Code:
mount
rootfs on / type rootfs (rw)
tmpfs on /dev type tmpfs (rw,seclabel,nosuid,relatime,mode=755)
devpts on /dev/pts type devpts (rw,seclabel,relatime,mode=600)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,seclabel,relatime)
selinuxfs on /sys/fs/selinux type selinuxfs (rw,relatime)
dmesg: pastebin. com/j4hnHkwg
PS. Can't insert links, and can't insert dmesg here, message are too long... =(
Some other logs:
Code:
<4>[ 1013.807952] ------------[ cut here ]------------
<4>[ 1013.807952] WARNING: at drivers/mmc/host/msm_sdcc.c:3538 msmsdcc_disable+0x84/0x10c()
<4>[ 1013.807952] mmc0: msmsdcc_disable: failed with error -22
<4>[ 1013.807983] [<c010cbc8>] (unwind_backtrace+0x0/0x11c) from [<c01730e8>] (warn_slowpath_common+0x48/0x60)
<4>[ 1013.807983] [<c01730e8>] (warn_slowpath_common+0x48/0x60) from [<c0173158>] (warn_slowpath_fmt+0x2c/0x3c)
<4>[ 1013.807983] [<c0173158>] (warn_slowpath_fmt+0x2c/0x3c) from [<c0659b18>] (msmsdcc_disable+0x84/0x10c)
<4>[ 1013.808013] [<c0659b18>] (msmsdcc_disable+0x84/0x10c) from [<c0646130>] (mmc_release_host+0x4c/0xb0)
<4>[ 1013.808013] [<c0646130>] (mmc_release_host+0x4c/0xb0) from [<c06571a0>] (mmc_blk_issue_rq+0x480/0x4c0)
<4>[ 1013.808044] [<c06571a0>] (mmc_blk_issue_rq+0x480/0x4c0) from [<c0657648>] (mmc_queue_thread+0xd4/0x19c)
<4>[ 1013.808044] [<c0657648>] (mmc_queue_thread+0xd4/0x19c) from [<c018f804>] (kthread+0x84/0x90)
<4>[ 1013.808044] [<c018f804>] (kthread+0x84/0x90) from [<c0107228>] (kernel_thread_exit+0x0/0x8)
<4>[ 1013.808074] ---[ end trace c0d52a61d7a24c7c ]---
<6>[ 1013.808074] mmc0: PM: sdcc_suspended=0, pending_resume=0, sdcc_suspending=0
<6>[ 1013.808074] mmc0: RPM: runtime_status=0, usage_count=0, is_suspended=0, disable_depth=0, runtime_error=-110, request_pending=0, request=0
<4>[ 1013.901123] ------------[ cut here ]------------
<4>[ 1013.901245] WARNING: at drivers/mmc/host/msm_sdcc.c:3510 msmsdcc_enable+0x108/0x144()
<4>[ 1013.901306] mmc0: msmsdcc_enable: failed with error -22
<4>[ 1013.901397] [<c010cbc8>] (unwind_backtrace+0x0/0x11c) from [<c01730e8>] (warn_slowpath_common+0x48/0x60)
<4>[ 1013.901519] [<c01730e8>] (warn_slowpath_common+0x48/0x60) from [<c0173158>] (warn_slowpath_fmt+0x2c/0x3c)
<4>[ 1013.901580] [<c0173158>] (warn_slowpath_fmt+0x2c/0x3c) from [<c065db64>] (msmsdcc_enable+0x108/0x144)
<4>[ 1013.901702] [<c065db64>] (msmsdcc_enable+0x108/0x144) from [<c0646018>] (__mmc_claim_host+0x170/0x180)
<4>[ 1013.901824] [<c0646018>] (__mmc_claim_host+0x170/0x180) from [<c0656d54>] (mmc_blk_issue_rq+0x34/0x4c0)
<4>[ 1013.901916] [<c0656d54>] (mmc_blk_issue_rq+0x34/0x4c0) from [<c0657648>] (mmc_queue_thread+0xd4/0x19c)
<4>[ 1013.902038] [<c0657648>] (mmc_queue_thread+0xd4/0x19c) from [<c018f804>] (kthread+0x84/0x90)
<4>[ 1013.902130] [<c018f804>] (kthread+0x84/0x90) from [<c0107228>] (kernel_thread_exit+0x0/0x8)
<4>[ 1013.902221] ---[ end trace c0d52a61d7a24c7d ]---
<6>[ 1013.902343] mmc0: PM: sdcc_suspended=0, pending_resume=0, sdcc_suspending=0
<6>[ 1013.902404] mmc0: RPM: runtime_status=0, usage_count=1, is_suspended=0, disable_depth=0, runtime_error=-110, request_pending=0, request=0
<6>[ 1013.903350] sps:BAM 0x12402000 enabled: ver:0x5, number of pipes:6
<3>[ 1013.908935] mmcblk0: error -110 sending status command, retrying
<3>[ 1013.914428] mmcblk0: error -110 sending status command, retrying
<3>[ 1013.919891] mmcblk0: error -110 sending status command, aborting
<3>[ 1013.919982] end_request: I/O error, dev mmcblk0, sector 4718594
<3>[ 1013.920104] EXT4-fs (mmcblk0p30): unable to read superblock
<4>[ 1013.920104] ------------[ cut here ]------------
<4>[ 1013.920135] WARNING: at drivers/mmc/host/msm_sdcc.c:3538 msmsdcc_disable+0x84/0x10c()
<4>[ 1013.920135] mmc0: msmsdcc_disable: failed with error -22
<4>[ 1013.920135] [<c010cbc8>] (unwind_backtrace+0x0/0x11c) from [<c01730e8>] (warn_slowpath_common+0x48/0x60)
<4>[ 1013.920166] [<c01730e8>] (warn_slowpath_common+0x48/0x60) from [<c0173158>] (warn_slowpath_fmt+0x2c/0x3c)
<4>[ 1013.920166] [<c0173158>] (warn_slowpath_fmt+0x2c/0x3c) from [<c0659b18>] (msmsdcc_disable+0x84/0x10c)
<4>[ 1013.920166] [<c0659b18>] (msmsdcc_disable+0x84/0x10c) from [<c0646130>] (mmc_release_host+0x4c/0xb0)
<4>[ 1013.920196] [<c0646130>] (mmc_release_host+0x4c/0xb0) from [<c06571a0>] (mmc_blk_issue_rq+0x480/0x4c0)
<4>[ 1013.920196] [<c06571a0>] (mmc_blk_issue_rq+0x480/0x4c0) from [<c0657648>] (mmc_queue_thread+0xd4/0x19c)
<4>[ 1013.920227] [<c0657648>] (mmc_queue_thread+0xd4/0x19c) from [<c018f804>] (kthread+0x84/0x90)
<4>[ 1013.920227] [<c018f804>] (kthread+0x84/0x90) from [<c0107228>] (kernel_thread_exit+0x0/0x8)
<4>[ 1013.920227] ---[ end trace c0d52a61d7a24c7e ]---
<6>[ 1013.920227] mmc0: PM: sdcc_suspended=0, pending_resume=0, sdcc_suspending=0
<6>[ 1013.920257] mmc0: RPM: runtime_status=0, usage_count=0, is_suspended=0, disable_depth=0, runtime_error=-110, request_pending=0, request=0
<3>[ 703.888671] EXT4-fs (mmcblk0p30): unable to read superblock
<3>[ 7.323852] mmcblk0: error -110 sending stop command, original cmd response 0x940, card status 0x2400e40
umount: can't umount /dev/block/mmcblk0: Invalid argument
mmc0: msmsdcc_enable: failed with error -22
<3>[ 757.383453] end_request: I/O error, dev mmcblk0, sector 4718592
<6>[ 1364.750000] mmc0: PM: sdcc_suspended=0, pending_resume=0, sdcc_suspending=0
<6>[ 1364.750091] mmc0: RPM: runtime_status=0, usage_count=1, is_suspended=0, disable_depth=0, runtime_error=-110, request_pending=0, request=0
<6>[ 1364.751068] sps:BAM 0x12402000 enabled: ver:0x5, number of pipes:6
<3>[ 1364.756591] mmcblk0: error -110 sending status command, retrying
<3>[ 1364.762145] mmcblk0: error -110 sending status command, retrying
<3>[ 1364.767608] mmcblk0: error -110 sending status command, aborting
<3>[ 1364.767700] end_request: I/O error, dev mmcblk0, sector 4718592
<3>[ 1364.767791] end_request: I/O error, dev mmcblk0, sector 4718593
<3>[ 1364.767852] end_request: I/O error, dev mmcblk0, sector 4718594
<3>[ 1364.767974] end_request: I/O error, dev mmcblk0, sector 4718595
<3>[ 1364.768035] end_request: I/O error, dev mmcblk0, sector 4718596
<3>[ 1364.768127] end_request: I/O error, dev mmcblk0, sector 4718597
<3>[ 1364.768218] end_request: I/O error, dev mmcblk0, sector 4718598
<3>[ 1364.768310] end_request: I/O error, dev mmcblk0, sector 4718599
I have exactly the same problem. I wasn't doing anything - I just lifted the cover the other morning to find it sitting at the Google logo. Can it really be hosed? Are we SOL for warranty repair?
eecummings said:
I have exactly the same problem. I wasn't doing anything - I just lifted the cover the other morning to find it sitting at the Google logo. Can it really be hosed? Are we SOL for warranty repair?
Click to expand...
Click to collapse
Have you guys test the nexus root tool kit?
it's a wonderful piece of software..
it does helped alot my nexus 4 when it's half bricked...
Try flashing system images and see what happens?
Sent from my XT1032 using XDA Premium 4 mobile app
Hi, I've the exact same problem too.
Did you manage to solve it or did you have to send it back for repair?
Thanks,
Alessandro
I believe this is the same problem I have: Not being able to format my corrupted cache partition.
Since my tablet was not unlocked or rooted I can't seem to flash a ROM either, even stock.
1c3_5n0w said:
Try flashing system images and see what happens?
Click to expand...
Click to collapse
I can't flash or erase or format any partition. I get the same error after some period of timeout.
Hello.
So - I bought this phone about ~8/9 months ago (in april 2014). I installed Cyanogenmod 11 by Maclaw twice, but there were problems with stability, so in August I decided to install AOSP by salvo (slv96).
Since then, everything was okay, until the middle of January (this year), when the phone... just restarted. It did not surprise me, because it restarted couple of times before. Unfortunately, it happend again - twice - so I started looking for possible causes. I noticed that the phone can boot normally, I can even use it for some time, but when I want to change something on it, it restarts, probably getting a kernel panic.
I tried to delete all data, or "triple wipe", but after that phone still had untouched ROM, just like it was before. Nothing was removed. So I downloaded Samsung Kies, because I tried to install an "original ROM", but Kies only shows the message "Connecting" and nothing more happens.
Next time I tried the ADB, I reset the flash counter by command:
Code:
dd if=/dev/zero of=/dev/block/mmcblk0 bs=1 count=1 seek=3145732
then I checked "what happens when I write the command dmesg | grep mmc*", which results in something like this:
Code:
[email protected]:/ # dmesg | grep mmc*
dmesg | grep mmc*
<7>[ 0.000000] Normal zone: 1248 pages used for memmap
<7>[ 0.000000] HighMem zone: 286 pages used for memmap
<5>[ 0.000000] Kernel command line: cachepolicy=writealloc mpcore_wdt.mpcore_margin=359 root=/dev/ram0 rw rootwait crash_reboot=yes crash_dump=no init=initconsole='null' [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] vmalloc=264M jig_smd=0 lpm_boot=0 checksum_pass=1 checksum_done=1 sec_debug.enable=0 sec_debug.enable_user=0 androidboot.serialno=473700e240071108 board_id=12 startup_graphics=1 logo. lcdtype=8 sbl_copy=1
<6>[ 0.000000] Console: colour dummy device 80x30
<6>[ 0.322540] print_constraints: dummy:
<6>[ 0.343658] print_constraints: db8500-sva-mmdsp:
<7>[ 0.343688] regulator regulator.9: regulator-db8500-sva-mmdsp-probed
<6>[ 0.343872] print_constraints: db8500-sva-mmdsp-ret:
<7>[ 0.343902] regulator regulator.10: regulator-db8500-sva-mmdsp-ret-probed
<6>[ 0.344329] print_constraints: db8500-sia-mmdsp:
<7>[ 0.344360] regulator regulator.12: regulator-db8500-sia-mmdsp-probed
<6>[ 0.344543] print_constraints: db8500-sia-mmdsp-ret:
<7>[ 0.344604] regulator regulator.13: regulator-db8500-sia-mmdsp-ret-probed
<6>[ 0.772735] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
<6>[ 1.227233] bt404_ts_device 3-0020: send reset command
<6>[ 1.255004] mmci-pl18x sdi2: mmc0: PL180 manf 80 rev4 at 0x80005000 irq 73,-1 (pio)
<6>[ 1.255096] mmci-pl18x sdi2: DMA channels RX dma0chan16, TX dma0chan17
<4>[ 1.298492] mmci-pl18x sdi0: Provided ocr_mask/setpower will not be used (using regulator instead)
<3>[ 1.298645] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 52
<6>[ 1.298950] mmci-pl18x sdi0: mmc1: PL180 manf 80 rev4 at 0x80126000 irq 92,-1 (pio)
<3>[ 1.298980] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 52
<6>[ 1.299072] mmci-pl18x sdi0: DMA channels RX dma0chan18, TX dma0chan19
<3>[ 1.322021] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 8
<3>[ 1.322357] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 5
<3>[ 1.322662] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 5
<3>[ 1.322967] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 5
<3>[ 1.323303] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 5
<3>[ 1.323608] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 55
<3>[ 1.323913] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 55
<3>[ 1.324249] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 55
<3>[ 1.324554] mmc0: [MMC] CMD TIMEOUT STATUS: 4, CMD: 55
<6>[ 1.368377] mmci-pl18x sdi1: mmc2: PL180 manf 80 rev4 at 0x80118000 irq 82,-1 (pio)
<6>[ 1.368438] mmci-pl18x sdi1: DMA channels RX dma0chan20, TX dma0chan21
<6>[ 1.471282] mmc0: new high speed DDR MMC card at address 0001
<6>[ 1.471771] mmcblk0: mmc0:0001 SEM04G 3.68 GiB
<6>[ 1.471954] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB
<6>[ 1.472137] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB
<6>[ 1.477600] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
<6>[ 1.484130] mmcblk0boot1: unknown partition table
<6>[ 1.487213] mmcblk0boot0: unknown partition table
<3>[ 1.487823] mmc1: [MMC] CMD TIMEOUT STATUS: 4, CMD: 52
<3>[ 1.488159] mmc1: [MMC] CMD TIMEOUT STATUS: 4, CMD: 52
<3>[ 1.511444] mmc1: [MMC] CMD TIMEOUT STATUS: 4, CMD: 5
<3>[ 1.511779] mmc1: [MMC] CMD TIMEOUT STATUS: 4, CMD: 5
<3>[ 1.512084] mmc1: [MMC] CMD TIMEOUT STATUS: 4, CMD: 5
<3>[ 1.512390] mmc1: [MMC] CMD TIMEOUT STATUS: 4, CMD: 5
<4>[ 1.548614] [<c0d7bb08>] (dump_stack+0x20/0x24) from [<c073f974>] (warn_slowpath_common+0x64/0x74)
<4>[ 1.548614] [<c073f974>] (warn_slowpath_common+0x64/0x74) from [<c073f9c4>] (warn_slowpath_fmt+0x40/0x48)
<6>[ 1.588836] mmio_probe
<6>[ 1.589508] mmio_camera mmio_camera: MMIO driver initialized with minor=42
<6>[ 1.589538] mmio_camera mmio_camera: system_rev 7, NCP6914 Camera Sub-PMIC
<7>[ 1.595886] mmio_cam_power_pin_control pin : 2 , state 1
<7>[ 1.596466] mmio_cam_power_pin_control pin : 2 , state 0
<4>[ 1.624908] [<c0d7bb08>] (dump_stack+0x20/0x24) from [<c073f974>] (warn_slowpath_common+0x64/0x74)
<4>[ 1.624908] [<c073f974>] (warn_slowpath_common+0x64/0x74) from [<c073f9c4>] (warn_slowpath_fmt+0x40/0x48)
<6>[ 1.636779] asoc: snd-soc-dummy-dai <-> ux500-msp-i2s.0 mapping ok
<4>[ 1.668792] mmc1: host does not support reading read-only switch. assuming write-enable.
<6>[ 1.700103] mmc1: new high speed SDHC card at address 0007
<6>[ 1.700683] mmcblk1: mmc1:0007 SD8GB 7.21 GiB
<6>[ 1.702301] mmcblk1: p1
<6>[ 2.112426] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: errors=panic
<6>[ 2.246673] EXT4-fs (mmcblk0p2): recovery complete
<6>[ 2.247863] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
<6>[ 2.299285] fs_mgr: Running /system/bin/e2fsck on /dev/block/mmcblk0p2
<6>[ 2.491821] e2fsck: /dev/block/mmcblk0p2: recovering journal
<6>[ 2.491882] e2fsck: /system/bin/e2fsck: unable to set superblock flags on/dev/block/mmcblk0p2
<6>[ 2.581146] EXT4-fs (mmcblk0p2): recovery complete
<6>[ 2.583099] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: journal_async_commit,errors=panic
<6>[ 2.625762] EXT4-fs (mmcblk0p4): recovery complete
<6>[ 2.626617] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
<6>[ 2.669433] fs_mgr: Running /system/bin/e2fsck on /dev/block/mmcblk0p4
<6>[ 2.741790] e2fsck: /dev/block/mmcblk0p4: recovering journal
<6>[ 2.741851] e2fsck: /system/bin/e2fsck: unable to set superblock flags on/dev/block/mmcblk0p4
<6>[ 2.781799] EXT4-fs (mmcblk0p4): recovery complete
<6>[ 2.782684] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: journal_async_commit,errors=panic
<6>[ 2.803741] EXT4-fs (mmcblk0p7): recovery complete
<6>[ 2.804870] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
<6>[ 2.849517] fs_mgr: Running /system/bin/e2fsck on /dev/block/mmcblk0p7
<6>[ 2.897705] e2fsck: /dev/block/mmcblk0p7: recovering journal
<6>[ 2.897766] e2fsck: /system/bin/e2fsck: unable to set superblock flags on /dev/block/mmcblk0p7
<6>[ 2.912231] EXT4-fs (mmcblk0p7): recovery complete
<6>[ 2.913024] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: journal_async_commit,errors=panic
<6>[ 2.920623] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts: errors=panic
<7>[ 3.355377] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 41301
<7>[ 3.362243] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 40447
<7>[ 3.367767] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 64030
<7>[ 3.367858] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 64025
<7>[ 3.370513] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 56153
<7>[ 3.374267] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 8012
<6>[ 3.374481] EXT4-fs (mmcblk0p5): 6 orphan inodes deleted
<6>[ 3.374511] EXT4-fs (mmcblk0p5): recovery complete
<6>[ 3.398315] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
<6>[ 3.449951] fs_mgr: Running /system/bin/e2fsck on /dev/block/mmcblk0p5
<6>[ 3.850677] e2fsck: /dev/block/mmcblk0p5: recovering journal
<6>[ 3.850738] e2fsck: /system/bin/e2fsck: unable to set superblock flags on /dev/block/mmcblk0p5
<7>[ 4.324157] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 41301
<7>[ 4.331481] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 40447
<7>[ 4.337310] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 64030
<7>[ 4.337463] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 64025
<7>[ 4.340911] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 56153
<7>[ 4.344512] EXT4-fs (mmcblk0p5): ext4_orphan_cleanup: deleting unreferenced inode 8012
<6>[ 4.344940] EXT4-fs (mmcblk0p5): 6 orphan inodes deleted
<6>[ 4.344970] EXT4-fs (mmcblk0p5): recovery complete
<6>[ 4.365631] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: discard,noauto_da_alloc,journal_async_commit,errors=panic
<3>[ 6.199615] u8500_shrm shrm_bus: common receive with l2 header 210 failed
<4>[ 6.279571] [<c0d7bb08>] (dump_stack+0x20/0x24) from [<c073f974>] (warn_slowpath_common+0x64/0x74)
<4>[ 6.279602] [<c073f974>] (warn_slowpath_common+0x64/0x74) from [<c073fa40>] (warn_slowpath_null+0x2c/0x34)
<3>[ 21.941711] end_request: I/O error, dev mmcblk0, sector 3078528
<3>[ 32.071746] end_request: I/O error, dev mmcblk0, sector 3321888
<3>[ 32.073638] end_request: I/O error, dev mmcblk0, sector 3322784
<3>[ 34.127593] end_request: I/O error, dev mmcblk0, sector 2155520
<3>[ 34.253173] end_request: I/O error, dev mmcblk0, sector 3083136
<3>[ 34.792480] end_request: I/O error, dev mmcblk0, sector 1544704
<3>[ 35.217437] end_request: I/O error, dev mmcblk0, sector 3074040
<3>[ 35.709747] mmc2: [MMC] CMD TIMEOUT STATUS: 4, CMD: 52
<3>[ 35.710083] mmc2: [MMC] CMD TIMEOUT STATUS: 4, CMD: 52
<3>[ 35.734436] mmc2: [MMC] CMD TIMEOUT STATUS: 4, CMD: 8
<6>[ 35.811065] mmc2: new high speed SDIO card at address 0001
<3>[ 36.042938] end_request: I/O error, dev mmcblk0, sector 3071560
<4>[ 36.340393] sdio_reset_comm():
<4>[ 38.452423] Unknown PRIVATE command WLS_BATCHING GET - ignored
<4>[ 38.453887] Unknown PRIVATE command WLS_BATCHING STOP - ignored
<3>[ 44.364715] end_request: I/O error, dev mmcblk0, sector 3689008
<3>[ 44.548583] end_request: I/O error, dev mmcblk0, sector 3724064
<3>[ 62.210357] end_request: I/O error, dev mmcblk0, sector 3716120
<3>[ 62.472076] end_request: I/O error, dev mmcblk0, sector 3690320
<3>[ 62.775665] end_request: I/O error, dev mmcblk0, sector 3716184
<3>[ 75.980651] end_request: I/O error, dev mmcblk0, sector 3724512
<3>[ 82.332397] end_request: I/O error, dev mmcblk0, sector 2794080
<3>[ 84.947631] end_request: I/O error, dev mmcblk0, sector 3876768
<3>[ 84.949829] end_request: I/O error, dev mmcblk0, sector 3875328
<3>[ 84.959594] end_request: I/O error, dev mmcblk0, sector 3869184
<3>[ 84.960906] end_request: I/O error, dev mmcblk0, sector 3866992
<3>[ 84.962799] end_request: I/O error, dev mmcblk0, sector 3871616
<3>[ 84.965332] end_request: I/O error, dev mmcblk0, sector 3866848
<3>[ 84.967163] end_request: I/O error, dev mmcblk0, sector 3866944
<3>[ 84.969177] end_request: I/O error, dev mmcblk0, sector 3870088
<3>[ 84.971954] end_request: I/O error, dev mmcblk0, sector 3878192
<3>[ 84.973846] end_request: I/O error, dev mmcblk0, sector 3877888
<3>[ 84.991668] end_request: I/O error, dev mmcblk0, sector 3867520
<3>[ 84.993743] end_request: I/O error, dev mmcblk0, sector 3871424
<3>[ 84.998046] end_request: I/O error, dev mmcblk0, sector 3886120
<3>[ 85.004394] end_request: I/O error, dev mmcblk0, sector 3866016
<3>[ 100.235717] end_request: I/O error, dev mmcblk0, sector 3716664
<3>[ 100.686798] end_request: I/O error, dev mmcblk0, sector 3716728
<3>[ 107.611114] end_request: I/O error, dev mmcblk0, sector 3723728
<3>[ 116.956024] end_request: I/O error, dev mmcblk0, sector 3725024
<3>[ 117.235870] end_request: I/O error, dev mmcblk0, sector 3716960
<3>[ 117.372741] end_request: I/O error, dev mmcblk0, sector 3725088
<3>[ 123.722656] end_request: I/O error, dev mmcblk0, sector 3717024
<3>[ 123.910125] end_request: I/O error, dev mmcblk0, sector 3079640
<3>[ 128.908752] end_request: I/O error, dev mmcblk0, sector 3079712
<3>[ 129.095489] end_request: I/O error, dev mmcblk0, sector 3079776
<3>[ 129.182556] end_request: I/O error, dev mmcblk0, sector 3079840
<3>[ 129.626342] end_request: I/O error, dev mmcblk0, sector 1546240
<3>[ 132.953887] end_request: I/O error, dev mmcblk0, sector 3725248
<3>[ 132.995880] end_request: I/O error, dev mmcblk0, sector 3079680
<3>[ 133.043151] end_request: I/O error, dev mmcblk0, sector 3079744
<3>[ 133.115478] end_request: I/O error, dev mmcblk0, sector 3079808
<3>[ 146.493164] end_request: I/O error, dev mmcblk0, sector 3079976
<3>[ 156.772979] end_request: I/O error, dev mmcblk0, sector 3085152
<3>[ 189.913391] end_request: I/O error, dev mmcblk0, sector 2504704
<3>[ 223.977478] end_request: I/O error, dev mmcblk0, sector 2798968
<3>[ 455.043640] end_request: I/O error, dev mmcblk0, sector 3410928
<3>[ 455.045532] end_request: I/O error, dev mmcblk0, sector 3417352
<3>[ 455.047393] end_request: I/O error, dev mmcblk0, sector 3451248
<3>[ 455.049499] end_request: I/O error, dev mmcblk0, sector 3362560
<3>[ 455.051147] end_request: I/O error, dev mmcblk0, sector 3343104
<3>[ 455.053039] end_request: I/O error, dev mmcblk0, sector 3481160
<3>[ 455.055145] end_request: I/O error, dev mmcblk0, sector 3341440
<4>[ 1770.800903] Unknown PRIVATE command WLS_BATCHING GET - ignored
<4>[ 1770.802154] Unknown PRIVATE command WLS_BATCHING STOP - ignored
<3>[ 1806.052703] end_request: I/O error, dev mmcblk0, sector 3716824
[email protected]:/ # dmesg | grep mmc* > wat.txt
dmesg | grep mmc* > wat.txt
sh: can't create wat.txt: Read-only file system
write: Broken pipe
I even tried to clear the internal flash memory from Linux Ubuntu by unmounting internal memory card in CWM Recovery and mounting it as Linux drive, but when I excecuted
Code:
dd if=/dev/zero of/dev/sdb1
and waited for ~2 hours, unmounted drive in Linux and mounted it back in Recovery, nothing happend. It still shows than at sdcard is AOSP.
What I can do with this phone? I have no warranty anymore, because the original system worked very poorly and even if I wanted to - I can't install it, because Samsung Kies does not recognise the phone. Is there any step-by-step tutorial about wiping contents of internal memory card and installing Android on sd card?
Did you try odin?
Yes, I tried ~week ago 4 times. Twice with version 3.10 and twice with Odin 3 v1.85. Installing stock ROM has not helped, I still have AOSP.
But how? There was an error in odin ot what?
Sent from my C1905 using XDA Free mobile app
There was no error, Odin just "stated" that everything was installed correctly, but when I reboot the phone, it still got unchanged AOSP ROM.
Hi All,
Anybody could help me coz got a bit of problem here.
Rom: stock GB 2.3.5 I8150XXKI8
It seems that everything is read-only except the external SD. After reboot, revert back to previous state.
Unable to go to recovery mode.
Done many success flashing in download mode ( flash stock,recovery) though and nothing. it just revert back to the previous state
Reformat usb storage also does not work.
Alot of apps force close.
Long pause at the samsung w logo.
mmcblk0p17 and mmcblk0p27 seems to have an error from below dmesg output.
Needs to confirm with anyone.
Thanks.
<3>[ 3.161895] init: MOUNT NAME /dev/block/mmcblk0p15
<3>[ 3.161925] init: SEC_DEVENC ***[/dev/block/mmcblk0p15][0]
<6>[ 3.181334] EXT4-fs (mmcblk0p15): mounted filesystem with ordered data mode. Opts: barrier=1
<3>[ 3.181395] init: MOUNT NAME /dev/block/mmcblk0p12
<3>[ 3.181426] init: SEC_DEVENC ***[/dev/block/mmcblk0p12][0]
<6>[ 3.186003] EXT4-fs (mmcblk0p12): barriers disabled
<6>[ 3.202056] EXT4-fs (mmcblk0p12): recovery complete
<6>[ 3.202697] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts: barrier=0
<3>[ 3.202758] init: MOUNT NAME /dev/block/mmcblk0p16
<3>[ 3.202758] init: SEC_DEVENC ***[/dev/block/mmcblk0p16][0]
<6>[ 3.205413] EXT4-fs (mmcblk0p16): barriers disabled
<3>[ 3.215056] init: [boot time] finish coldboot
<6>[ 3.216735] EXT4-fs (mmcblk0p16): recovery complete
<6>[ 3.217314] EXT4-fs (mmcblk0p16): mounted filesystem with ordered data mode. Opts: barrier=0
<4>[ 3.220519] EXT4-fs (mmcblk0p27): warning: mounting unchecked fs, running e2fsck is recommended
<6>[ 3.221129] EXT4-fs (mmcblk0p27): mounted filesystem without journal. Opts: (null)
<4>[ 3.238127] EXT4-fs (mmcblk0p27): warning: mounting unchecked fs, running e2fsck is recommended
<6>[ 3.238738] EXT4-fs (mmcblk0p27): mounted filesystem without journal. Opts: (null)
<4>[ 3.248168] EXT4-fs (mmcblk0p27): warning: mounting unchecked fs, running e2fsck is recommended
<6>[ 3.249205] EXT4-fs (mmcblk0p27): mounted filesystem without journal. Opts: (null)
<4>[ 3.258544] EXT4-fs (mmcblk0p27): warning: mounting unchecked fs, running e2fsck is recommended
<6>[ 3.259154] EXT4-fs (mmcblk0p27): mounted filesystem without journal. Opts: (null)
<4>[ 3.271483] mmc2: host does not support reading read-only switch. assuming write-enable.
<6>[ 3.271514] mmc2: new high speed SDHC card at address 1234
<6>[ 3.271605] sdio_al mmc2:1234: Probing..
<6>[ 3.271605] sdio_al mmc2:1234: Not an SDIO card
<6>[ 3.271941] mmcblk1: mmc2:1234 SA16G 14.6 GiB
<6>[ 3.272124] mmcblk1: p1
<4>[ 3.276579] EXT4-fs (mmcblk0p27): warning: mounting unchecked fs, running e2fsck is recommended
<6>[ 3.277220] EXT4-fs (mmcblk0p27): mounted filesystem without journal. Opts: (null)
<3>[ 3.278319] init: [disk_config] :::: /dev/block/mmcblk0p27 (ext4)(opt (null)):::::
<3>[ 3.278349] init: internal_storage : ext_identify open
<3>[ 3.278380] init: internal_storage : ext_identify lseek
<3>[ 3.279234] init: internal_storage : ext_identify open
<3>[ 3.279265] init: internal_storage : ext_identify lseek
<3>[ 3.279295] init: MOUNT NAME /dev/block/mmcblk0p27
<3>[ 3.279326] init: SEC_DEVENC ***[/dev/block/mmcblk0p27][0]
<3>[ 3.279357] init: failed that mount s:'/dev/block/mmcblk0p27', t:'/efs', f:ext4 ,op null) (Device or resource busy)
<3>[ 3.279418] init: [disk_config] :::: /dev/block/mmcblk0p17 (ext4)(opt (null)):::::
<3>[ 3.279448] init: internal_storage : ext_identify open
<3>[ 3.279479] init: internal_storage : ext_identify lseek
<3>[ 3.280852] init: internal_storage : ext_identify open
<3>[ 3.280882] init: internal_storage : ext_identify lseek
<3>[ 3.282439] init: [disk_config] :::: fsck -> /dev/block/mmcblk0p17 (ext4):::::
<3>[ 3.282836] init: [disk_config] DEVENC : not mormal [0]
<3>[ 3.282836] init: [disk_config] DEVENC : fs_check with original dev_path
<3>[ 3.644621] mmc1 data status (0x8)
<3>[ 3.644652] mmc1: Data timeout opcode = 0x12
<3>[ 3.644682] mmc1: DMA channel flushed (0x80000004)
<3>[ 3.644682] Flush data: 0000c003 4f713000 00000000 00200040 00290028 00002003
<4>[ 3.645018] mmcblk0: retrying using single block read
<3>[ 4.017912] init: SEC_DEVENC check crypt status
<3>[ 4.017973] init: MOUNT NAME /dev/block/mmcblk0p17
<3>[ 4.017973] init: SEC_DEVENC ***[/dev/block/mmcblk0p17][1]
<3>[ 4.017973] init: SEC_DEVENC checkCrypt main
<3>[ 4.316953] mmc1 data status (0x8)
<3>[ 4.316953] mmc1: Data timeout opcode = 0x12
<3>[ 4.316984] mmc1: DMA channel flushed (0x80000004)
<3>[ 4.316984] Flush data: 0000c003 4f713000 00000000 00200040 05b905b8 00002003
<4>[ 4.317320] mmcblk0: retrying using single block read
<3>[ 4.519804] mmc1 data status (0x8)
<3>[ 4.519834] mmc1: Data timeout opcode = 0x12
<3>[ 4.519865] mmc1: DMA channel flushed (0x80000004)
<3>[ 4.519865] Flush data: 0000c003 4f713000 00000000 00200040 05b905b8 00002003
<4>[ 4.520170] mmcblk0: retrying using single block read
<3>[ 4.727903] mmc1 data status (0x8)
<3>[ 4.727903] mmc1: Data timeout opcode = 0x12
<3>[ 4.727934] mmc1: DMA channel flushed (0x80000004)
<3>[ 4.727934] Flush data: 0000c003 4f713000 00000000 00200040 04690468 00002003
<4>[ 4.728300] mmcblk0: retrying using single block read
<3>[ 5.135984] mmc1 data status (0x8)
<3>[ 5.136015] mmc1: Data timeout opcode = 0x12
<3>[ 5.136045] mmc1: DMA channel flushed (0x80000004)
<3>[ 5.136045] Flush data: 0000c003 4f713000 00000000 00200040 00b900b8 00002003
<4>[ 5.136381] mmcblk0: retrying using single block read
<4>[ 5.233640] EXT4-fs (mmcblk0p17): warning: mounting fs with errors, running e2fsck is recommended
<6>[ 5.234983] EXT4-fs (mmcblk0p17): recovery complete
<6>[ 5.235959] EXT4-fs (mmcblk0p17): mounted filesystem with ordered data mode. Opts: errors=continue
<3>[ 5.236020] init: SEC_DEVENC uncrypted parition mounted
<4>[ 5.237577] param_init !
<3>[ 5.237729] init: [boot time] processing action 0x3b6d8 (post-fs)
<3>[ 5.237760] init: [disk_config] :::: /dev/block/mmcblk0p28 (vfat)(opt (null)):::::
<3>[ 5.240323] init: oem_name (android )
<3>[ 5.244382] init: oem_name (android )
<3>[ 5.244474] init: [disk_config] :::: fsck -> /dev/block/mmcblk0p28 (vfat):::::
<3>[ 5.244901] init: [disk_config] DEVENC : not mormal [0]
<3>[ 5.244932] init: [disk_config] DEVENC : fs_check with original dev_path
<3>[ 5.599302] mmc1 data status (0x8)
<3>[ 5.599302] mmc1: Data timeout opcode = 0x12
<3>[ 5.599332] mmc1: DMA channel flushed (0x80000004)
<3>[ 5.599332] Flush data: 0000c003 4f713000 00000000 00200040 02690268 00002003
<4>[ 5.599698] mmcblk0: retrying using single block read
<3>[ 6.010587] mmc1 data status (0x8)
<3>[ 6.010587] mmc1: Data timeout opcode = 0x12
<3>[ 6.010617] mmc1: DMA channel flushed (0x80000004)
<3>[ 6.010617] Flush data: 0000c003 4f713000 00000000 00200040 02790278 00002003
<4>[ 6.010984] mmcblk0: retrying using single block read
<3>[ 6.435544] mmc1 data status (0x8)
<3>[ 6.435544] mmc1: Data timeout opcode = 0x12
<3>[ 6.435574] mmc1: DMA channel flushed (0x80000004)
<3>[ 6.435574] Flush data: 0000c003 4f713000 00000000 00200040 01b901b8 00002003
<4>[ 6.435910] mmcblk0: retrying using single block read
<3>[ 6.638852] mmc1 data status (0x8)
<3>[ 6.638883] mmc1: Data timeout opcode = 0x12
<3>[ 6.638883] mmc1: DMA channel flushed (0x80000004)
<3>[ 6.638913] Flush data: 0000c003 4f713000 00000000 00200040 00b900b8 00002003
<4>[ 6.639249] mmcblk0: retrying using single block read
my internal memory was damaged. I flashed stock rom, entered it's recovery and formatted the internal memory. then installed cwm and installed custom rom. now everything is perfect.
ozgurakman said:
my internal memory was damaged. I flashed stock rom, entered it's recovery and formatted the internal memory. then installed cwm and installed custom rom. now everything is perfect.
Click to expand...
Click to collapse
Hi,
Thanks for the reply and good for you ozgurakman coz able to go to recovery mode. But I'm unable to go to recovery mode to repair the system though. Press the 3 recovery buttons. and just a screen flicker. It seem that my recovery corrupt also. Even after I reflash the recovery block only, still nada.
It seem that I'm running out options though. Anybody?
Did you tried to install cwm?
ozgurakman said:
Did you tried to install cwm?
Click to expand...
Click to collapse
yup also trying that one. also using the dd command in case the odin not working.
If dd command works, everything is fine. if dd command not working +Odin is not working, flashing via jtag is the only way.
ozgurakman said:
If dd command works, everything is fine. if dd command not working +Odin is not working, flashing via jtag is the only way.
Click to expand...
Click to collapse
the weird is that both dd and odin works. Also when i try to reboot it shutdown instead.
Will try to find shop that can do jtag. thanks
zaffrullah said:
the weird is that both dd and odin works. Also when i try to reboot it shutdown instead.
Will try to find shop that can do jtag. thanks
Click to expand...
Click to collapse
If I helped you, please press to thanks button
Last advise: try to different Odin version, different ops, different Rom.
Select to wipe everything.