Hi,
I'm having trouble getting back from a KitKat Rom to an JB or ICS ROM.
I'm getting stuck with the firmware. It's flashing OK (I've tried several different ones), but when I boot up and try to get into CWM it just sits there on the firmware logo (e.g. the LUPUS logo, or the Rush logo).
Is there something fundamentally stopping me going back to an ICS or JB firmware, after I've previously had KitKat running?
HELP
Oh, this is the Kitkat ROM I originally installed, and it's included kernel:
http://forum.xda-developers.com/showthread.php?t=2570072
If I flash that kernel again, I can get into Kitkat successfully, no problem at all.
As above, if I flash any other kernel, I just can't get into CWM.
gsf600y said:
Hi,
I'm having trouble getting back from a KitKat Rom to an JB or ICS ROM.
I'm getting stuck with the firmware. It's flashing OK (I've tried several different ones), but when I boot up and try to get into CWM it just sits there on the firmware logo (e.g. the LUPUS logo, or the Rush logo).
Is there something fundamentally stopping me going back to an ICS or JB firmware, after I've previously had KitKat running?
HELP
Click to expand...
Click to collapse
You can flash stock ICS firmware using Flashtool, then flash a JB custom kernel with a recovery. From there, use the recovery to flash a JB ROM.
僕のLT18iから送られてきた
popthosegaskets said:
You can flash stock ICS firmware using Flashtool, then flash a JB custom kernel with a recovery. From there, use the recovery to flash a JB ROM.
Click to expand...
Click to collapse
Thanks for your reply.
What is the need for flashing an ICS kernel first?
I'll give it a go, but flashing a custom ICS kernel with a recovery I've been unable to get into CWM.
I'm probably doing something really stupid.
gsf600y said:
Thanks for your reply.
What is the need for flashing an ICS kernel first?
I'll give it a go, but flashing a custom ICS kernel with a recovery I've been unable to get into CWM.
I'm probably doing something really stupid.
Click to expand...
Click to collapse
Flashing ICS is recommended first since this will restore you phone's memory partitions. KK uses different memory partitions to make it run properly. This will also wipe your phone's data and allows you to do a clean install that should eliminate most errors that you encounter during ROM installation.
Ok, thanks so much for the advice
I'll give it a go and let you know how I get on!
Ok, I'm back on Gingerbread stock firmware
Android v2.3.4, Build 4.0.2.A.0.62.
I can't find an ICS based FTF file - everything is either 404 or on hotfiles, which is dead.
I've unlocked the bootloader (which I thought I'd already done, but maybe the flash of the firmware undoes that?)
Not sure where to go from here.
gsf600y said:
Ok, I'm back on Gingerbread stock firmware
Android v2.3.4, Build 4.0.2.A.0.62.
I can't find an ICS based FTF file - everything is either 404 or on hotfiles, which is dead.
I've unlocked the bootloader (which I thought I'd already done, but maybe the flash of the firmware undoes that?)
Not sure where to go from here.
Click to expand...
Click to collapse
Check my signature for stock firmwares, there are working links for Arc and Arc S.
Someguyfromhell said:
Check my signature for stock firmwares, there are working links for Arc and Arc S.
Click to expand...
Click to collapse
BOOKMARKING THAT!!
Very useful thanks a lot
Currently firing up FreeXperia CM9....fingers crossed.....
Related
I have flashed a rom and kernel for the first time but what is the initial step to do it the second time? for example if I was going to flash C.A.M.P ROM how would I be able to do it properly to get it to work just like my first ROM?
I have previously flashed doom ics v3 kernel and Mark Phyton ICS
x1rocket said:
I have flashed a rom and kernel for the first time but what is the initial step to do it the second time? for example if I was going to flash C.A.M.P ROM how would I be able to do it properly to get it to work just like my first ROM?
I have previously flashed doom ics v3 kernel and Mark Phyton ICS
Click to expand...
Click to collapse
Flash the required kernel first. Then install rom through CWM its the same steps. However if I were you I do a fresh install of stock gb before installing a new rom. Because sometimes changing from different roms can screw up some things.
chery2k said:
Flash the required kernel first. Then install rom through CWM its the same steps. However if I were you I do a fresh install of stock gb before installing a new rom. Because sometimes changing from different roms can screw up some things.
Click to expand...
Click to collapse
how come? what about nandroid backup of stock gb? but I dont have backup.... *PANIC ATTACK*
x1rocket said:
how come? what about nandroid backup of stock gb? but I dont have backup.... *PANIC ATTACK*
Click to expand...
Click to collapse
Did you try using using flashtool to revert your xperia play back to gb using flashtool? Otherwise you will learned the hard way if your xperia play soft bricks.
hi everyone i wanted to know taht i am on aokp(jb) rom and i wanna go to a stock based(ics) without using flashtool.
any help will be appreciated.
The best way is the flashtool to return to stock, otherwise a stock based kernel and ROM in the same way you flashed AOKP.
Sent from Myushi
but most of the stock based roms said that i need the 587.baseband to install the rom. please let me know coz am in no mood to use flashtool
.587 is not a baseband, it's the stock 4.0.4 ICS firmware version (fully 4.1.B.0.587 iirc). Just download and flash via flashtool
Sent from my LT18i using xda premium
ok i just wanted to make sure if their is any other way other then flashtool thanks.
Just flash the kernel, wipe everything, and install the ICS ROM you want. I came back to ICS from CM10 without flashing stock ftf, and no issues at all.
soumya_digi said:
Just flash the kernel, wipe everything, and install the ICS ROM you want. I came back to ICS from CM10 without flashing stock ftf, and no issues at all.
Click to expand...
Click to collapse
thankyou so much all that getting me worried was all the devs saying i need 587.firmware thanks mate.
Hello ...
two days ago i've unlocked and flashed custom kernel & rom (Super JB) on device Arc S LT18. I, and don't know why, used Flashtools to recover to 2.3.4 and after that installed the mentioned rom (yes i've cleared all). Now the device only boots if i use Menu + Power button. What the hell ? If i only use the power button, the green light flashes and nothing else (no boot). DO i need a clean wipe and all over again? Maybe i must flash original kernel 5.4. ?
After flashing the ROM in recovery, did you flash the patch for your device as mentioned in the installation instructions?
cacigge said:
After flashing the ROM in recovery, did you flash the patch for your device as mentioned in the installation instructions?
Click to expand...
Click to collapse
yes, i've flashed the patch after the rom. I really don't know what happened, was it the flashed kernel (that is the first time i've encounter the problem) ? or maybe that i've installed a stock rom (2.3.4) and didn't boot the device (and then proceed with the custom installation) ? or maybe it's the kernel, because i've flashed the Super Fusion and not the fusion 5.4
now i've installed the official CyanogenMod 10.2, but can't seem to fix this bug
oh yea and all the browsers keep on crashing
deathL said:
oh yea and all the browsers keep on crashing
Click to expand...
Click to collapse
you need to flash ics stock firmware 4.04 first then you can flash custom kernel then custom JB rom
jb rom cant's be flashed on gingerbread 2.3.4 roms, you have to be on stock ics 4.04
bobb83 said:
you need to flash ics stock firmware 4.04 first then you can flash custom kernel then custom JB rom
jb rom cant's be flashed on gingerbread 2.3.4 roms, you have to be on stock ics 4.04
Click to expand...
Click to collapse
ohhh... dang...umm ok i'll try to install stock 4.04 via flashtools. i don't need to recover to stock 2.3.4 first right?
bobb83 said:
you need to flash ics stock firmware 4.04 first then you can flash custom kernel then custom JB rom
jb rom cant's be flashed on gingerbread 2.3.4 roms, you have to be on stock ics 4.04
Click to expand...
Click to collapse
What difference does it make, if both kernel and /system partition are completely formatted anyway?
Someguyfromhell said:
What difference does it make, if both kernel and /system partition are completely formatted anyway?
Click to expand...
Click to collapse
coz i tried myself going from gingerbread to jb roms does not work for me thats why i stated that from my own exprience
---------- Post added at 06:13 PM ---------- Previous post was at 06:03 PM ----------
deathL said:
ohhh... dang...umm ok i'll try to install stock 4.04 via flashtools. i don't need to recover to stock 2.3.4 first right?
Click to expand...
Click to collapse
its your choice mate if you want to be on GB rom then flash gb 2.3.4 or if you want to be on ICS then flash ics 4.04 stock rom
but if you want to flash JB custom roms then you need to flash ics stock rom first.
you can either reover to ICS or GB via flashtool its upto you
well the cm 10.2 works really good and maybe i will test cm 11 (or any custom rom from 4.2 above). so i will try your suggestion and see what happens.
EDIT: well the stock browser crashed today -.-' ... will have to test further ... and the strange boot is kinda fixed (it was my fault because i didn't pushed the power button long enought lol)
EDIT 2: stock browser simply force close everytime i use it. google play store doesn't work well :/
Hey everyone,
last week I flashed my girlfriend's XMS with several custom ROMs, but none of them could really satisfy us, so I want to re-flash the stock ROM.
My question is: Can I just flash the ftf file with the flashtool if there is currently CM11 running on the device? Or do I need to erase the system before?
Will this also flash "stock recovery"? Is there a way to do this?
Thanks!
Yes, you can flash stock ROM. There is no need to format system, Flashtool will do its work. Stock recovery will not be flashed, because we don't have stock recovery on our device. But you can flash stock kernel with CWM or PhilZ Touch recovery.
if you want to leave your recovery ..check kernel
sin in exclude list in flashtool
Sent from my C1905 using XDA Premium 4 mobile app
Farsiris said:
if you want to leave your recovery ..check kernel
sin in exclude list in flashtool
Click to expand...
Click to collapse
No! Phone will not boot with custom ROM kernel (if custom ROM is not based on stock). So it is necessary to flash full stock at first and then to flash stock kernel with recovery, if you want to have recocery.
cucumber09 said:
No! Phone will not boot with custom ROM kernel (if custom ROM is not based on stock). So it is necessary to flash full stock at first and then to flash stock kernel with recovery, if you want to have recocery.
Click to expand...
Click to collapse
Have you tried it ? Cuz i ve tried it many many times !
Farsiris said:
Have you tried it ? Cuz i ve tried it many many times !
Click to expand...
Click to collapse
You flashed stock via Flashtool after CM11 or CM-based ROM without flashing stock kernel? It should not boot, I think, because 4.3 and 4.4 kernels are different.
Has anyone tried this? I need to do this also but I'm a little bit confused about flashing kernel. I tried to find a detailed guide somewhere but no success
hi guys,
first of, forgive me If I cannot utilize google or xda's search engine for looking a good solution to my issue, I just cannot think of the right keywords to look for.
for several months now, I currently have CM11 fxp334 by pencam and Bootloader is unlock. Recently Im encountering random reboot issues and I think its getting worst and I am not sure if it has something to do with my link2sd, because at times when it does randomly reboots, I lose some apps that are link to my sdcard after booting.
1) Im thinking of either updating to the latest CM11(or CM12) nightly builds (I have cwm obviously) to assume that latest builds have less bugs
2) or is it possible to use cwm in trying to install/flash stock xperia M firmware because CM seems to be a power hog based on my own observation vs stock sony 4.3 JB. If this can be done, can some good soul point me to the right direction please.
I have my rest days, I hope I can use it by fixing my phone. Thank you.
Just flash your stock .ftf file to go back to stock.
You will have to reflash recovery tho.
*blink*
RedLedLight said:
Just flash your stock .ftf file to go back to stock.
You will have to reflash recovery tho.
*blink*
Click to expand...
Click to collapse
flash by using cmw, or flashtool? can cmw recognize a *.ftf file?
and when you said that I will have to reflash recovery, I can still use the cmw recovery that Ive previously used with my CM11 together with stock sony rom?
prince10t said:
flash by using cmw, or flashtool? can cmw recognize a *.ftf file?
and when you said that I will have to reflash recovery, I can still use the cmw recovery that Ive previously used with my CM11 together with stock sony rom?
Click to expand...
Click to collapse
flash .ftf using flashtool flashmode
afaik cwm only support .zip file for flashing
you can have cwm on stock rom when you flash stock kernel that includes cwm
flash it with flashtool fastboot mode
just press thanks if it's helps instead of typing it