Odin worked successfully at least once because I flashed the stock recovery from here.
Now whenever I try nothing happens.
1)Charge Tablet to at least 50%
2)Open Odin is administrator
3)Load md5 file by clicking AP
4)Wait for md5 check to complete
5)Power off Tab
6)Power on Tab while holding volume up
7)Connect USB cable
8)Hit Start in Odin
In Odin3 v1.85 and v3.09
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P5210XXUAMG6_P5210XACAMH2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
Then I plug in cable and press start
Code:
<OSM> All threads completed. (succeed 0 / failed 0)
BUT when I try with Tab normally powered on I get farther
Code:
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What am I doing wrong? I have developer options enabled and have USB debugging and Allow mock locations checked. I have Kies installed on my computer.
swishbucket1 said:
Odin worked successfully at least once because I flashed the stock recovery from here.
Now whenever I try nothing happens.
1)Charge Tablet to at least 50%
2)Open Odin is administrator
3)Load md5 file by clicking AP
4)Wait for md5 check to complete
5)Power off Tab
6)Power on Tab while holding volume up
7)Connect USB cable
8)Hit Start in Odin
In Odin3 v1.85 and v3.09
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P5210XXUAMG6_P5210XACAMH2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
Then I plug in cable and press start
Code:
<OSM> All threads completed. (succeed 0 / failed 0)
BUT when I try with Tab normally powered on I get farther
Code:
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What am I doing wrong? I have developer options enabled and have USB debugging and Allow mock locations checked. I have Kies installed on my computer.
Click to expand...
Click to collapse
Step 5. No need to power off.
Step 6. It should be "press volume down,home and power keys together" to go into ODIN mode.
Try 3.07.. 3.09 did not work for me either
Sent from my SM-T210R using xda app-developers app
Related
So I was attempting to flash the CWM6 safe kernel to upgrade to CM9 beta 1 on my girlfriend's phone. The kernel flash didn't go well and the phone was stuck at the splash screen. I'm attempting to ODIN FH13 via One Click. ODIN sees the phone, and the process starts...but always fails at:
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012>
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas/help?
Thanks in advance.
Nevermind...it all the of the sudden felt like working after 3 attempts.
So... a guy brings me a Galaxy S3 SHG-T999 and says it won't boot up..gets stuck on the Galaxy Boot Logo Screen.
The phone will not go into recovery mode,
PC will not charge the phone while plugged in.
PC does not recognize the phone when at boot up screen.
When plugged in not booted, a gray battery Icon appears and disappears.
The phone will go into download mode
When in download mode the Text shows that everything is still stock and no binary has been downloaded.
All correct drivers installed
I have tried using Kies and Odin to flash using the Stock Rom
Kies see the device but fails, Odin sees the device and reads the file but fails to write
in Odin I have Reboot checked F Reset checked
Is there anything I can do to get the phone to boot from an SD card so that I can reset the phone and reflash to stock ROM?
If Odin Failed while the phone was in download mode, please post the Odin log.
Odin Log
Perseus71 said:
If Odin Failed while the phone was in download mode, please post the Odin log.
Click to expand...
Click to collapse
This is my Odin log
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVUEMJC_T999TMBEMJC_T999UVUEMJC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Second Odin Log Fail
I tried a different Stock rom and did not get a fail but it also did nothing at all
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVUEMJC_T999TMBEMJC_T999UVUEMJC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
Something's wonky here. Did you check the .PIT checkbox ?
Ok, I got a new Note II the other day with 4.3 already installed via Kies or OTA. I attempted to push, via ODIN, "CF-Auto-Root-d2tmo-d2tmo-sght999.tar". I REALIZE THIS IS THE ROOT FOR S3; I KNOW I FLASHED THE WRONG FILE. PLEASE DO NOT POST SAYING I FLASHED THE WRONG FILE. I KNOW I SCREWED UP BIG TIME, AND I'M HOPING SOMEONE IS NICE ENOUGH TO TRY AND HELP ME THROUGH THIS. My laptop sat there for the better part of 2 hours acting like ODIN was cranking along but the bar never moved. After 2 hours, I had to pull the cord from the phone (stupid move, I know!), and this is, of course, where the problem began.
Now, I get the coveted "Firmware Upgrade encountered an issue. Please select recovery mode in Kies & try again." screen. The phone will, obviously, go no further than this in booting up. I am able to get to download mode.
I attempted to install JellyBean Release 4.3 (December 2013) from this thread to alleviate the issue. Here's the ODIN result:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Now, as I sit here and write this, I think installing a stock firmware like this one might not work at all. I need to install a recovery (stock or otherwise) to make this problem disappear. I tried to reinstall the CF-Auto-Root file and got this result:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-d2tmo-d2tmo-sght999.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-d2tmo-d2tmo-sght999.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Again, it didn't do anything for hours. I pulled the cord again since it didn't look like it was actually writing anything to my phone.
I don't think I can use KIES as a last resort since I never backed up the phone through KIES before. I am out of ideas, and I would really like to get this phone operational again. Also, the serial number has been removed from the device (Igot the phone from Ebay), so I don't think I could use this route either.
Any and all help would be greatly appreciated.
Thanks in advance!
Download and flash CF auto-root for sgh-t889(link below)it includes recovery, then perform factory reset by rebooting in to recovery.
http://download.chainfire.eu/266/CF-Root/CF-Auto-Root/CF-Auto-Root-t0ltetmo-t0ltetmo-sght889.zip
Sent from my SGH-T889 using xda app-developers app
I have a Galaxy S3 Tmobile - not rooted. I wiped my phone to default and when it tried to power on, it gave me couldn't mount e:\ - don't remember the exact path. After attempting to flash with stock firmware T999UVDMD5_T999TMBDMD5_TMB and 16GB.pit file with odin 3.04 and 3.07 that failed:
Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone:
ODIN MODE
Product Name: SGH-T999L
CUSTOM BINARY DOWNLOAD: Yes (1 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit; 0
BOOTLOADER Bit: 0
SECURE CHECK FAIL: PIT
Thanks in advance!
Try flashing without the PIT file?
audit13 said:
Try flashing without the PIT file?
Click to expand...
Click to collapse
I've tried that but it still fails:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVUENC2_T999TMBENC2_T999UVUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Which bootloader is on the phone? Are the error messages from Odin 3.07? Are you unchecking everything except f.reset time and auto reboot in Odin?
Hello XDA.
I have been trying to get my S9 recognized in Odin, but nothing is working.
I have tried all the USB slots, tried a different cable, and have all the drivers installed.
My Odin does work on my A42 5G, S7, and S5 though.
I feel like this may be a cause of windows 11 maybe?
Any help is appreciated.
Also, just in case anyone wants it, heresw the Odin output.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm also having the same recognition issue on my Linux install.