Develop Bugs

crashed/frozen. wont boot (FInixNOver) - cant reflash!

Hi guys.
I was using the installed the FInixNOver 3.0.1 ROM onto my SPV M700 and it was great. I've had it for about 2 weeks without any problems.
Last night I looked at my phone, only to realise that it was completley dead. This didnt shock me to much because the battery was running low, and i decided to let it die completley before recharging it again.
I charged my phone overnight and switched it on this morning, but the phone would freeze at the 'FInixNOver' splash screen (the numbers at the bottom of the screen would appear overlaying the splash, but the phone wouldnt go pass this point).
The only way to turn off the phone from this state is to eject the battery. I have tried removing the sim card, turning it back on in as many ways as possible but to no avail. I am able to get to the TriColor test screen (im running IPL-0.50 / SPL-1.30.Olipro) but with all the custom roms available, they all use the ROMUpdateUtility which requires the phone to have established an activesync connection initially (but this would mean my phone would have to be 'on completley' - so this is catch 22.)
For the record, my phone/battery died while my wired handsfree was attached (dunno if thats of any interest to anyone or the rom baker).
But it looks like the only way i'll be able to flash my phone is by finding a way to install the .nbh file without using the RUU method. Because I can put my phone into test mode manually.... any help or guidence would be very much appriciated.
Thanks.

Ok can you get it into bootloader? power/camera buttons and reset?
sorry didnt read fully.
right get your device into bootloader first,
then open active sync (are you using xp)
then open connection settings and disable usb connection,
put your device into bootloader mode, then run any rom upgrade, i prefer the WM6.1 pdaviets from HERE (Username: PDAVIET / Password: pdaviet)

Your pda does not need active sync with ruu's, so no catch 22. if you turn off usb connection in active sync, you can still run ruu and it will be recognised, unless you are using vista, where you need to change your HTC SYNC drivers.

Thanks for your quick response...
Yes I can get into boot loader using the power and camera buttons (or holding the power and camera buttons when resetting the phone)...
When the phone is in boot loader mode, active sync doesnt even detect the phone anyway, but nevertheless, I have followed your instructions and disabled the USB Connection. (BTW, yes i am using XP)
The phone is still in boot loader mode, so now i try and execute the ROMUpdateUtility.exe and go through the steps, at the 1st step i tick the tickbox and click next, and the 2nd step i tick the tickbox and click next. (this step says DO NOT enter the bootloader manually? - but i have havent i?) anyway, when i click next, it says... "Verifying the information on your Trinity... Please Wait..." for about 10 seconds, and then i get a message "ERROR [260] : CONNECTION"
What am i doing wrong?

Huumm.. why dont you flash your phone throw the sd card??
Read this link:
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing

try to flash your phone with some official rom and after that flash it with any other you want!

manos_23 said:
try to flash your phone with some official rom and after that flash it with any other you want!
Click to expand...
Click to collapse
I would recommend this option above, to be safe, i usually get them error messages when the battery is below 50% or sometimes i try it again and it works. it does state do not manually enter bootloader but i always do it this way.

also make sure active sync is not still running in taskmanager under the alais: wcescomm.exe and WCESMGR.exe, end them both.

I've just tried using an official ROM, but the problem still occurs with the 'connecting'. It doesnt seem that the computer picks up a connection to the phone whatsoever.
Should i be concerned that at the bottom of the bootloader screen it says "serial", is this correct?
Im starting to get annoyed now.

Bye,
the bottom of the sreen mast say "usb" not serial.

it seems there is a problem, if it states serial. as it should say usb. try THIS

Seems like the problem was that my USB lead was loose and made a bad connection, hence why the bootloader showed 'serial' and not 'usb'... as soon as i wiggled it and heard the 'connection noise' in windows, i knew i was good to go, and so using the RUU worked fine to reupdate my phones ROM.
Thanks for your help.
My only question is that why did it happen in the first plave?

WIZZKID - I just saw your post here now. I have to tell you that I also saw "SERIAL" at the bottom of the bootloader screen and not "USB". As I said I returned it to get another phone but maybe I will try something else for now instead of a P3600i. I will monitor your thread to see how it turns out for your phone, because it seems that we have the same problem.

if you see "serial" instead "usb" your problem is in the usb cable, usb port from your computer or in the usb connector from your trinity!!!!!
I was having the same problem that you have!! my problem was from my usb from mine trinity!! see if the conector is at good conditions !!!

Well as some of you may know, I got my Trinity replaced for sticking at the WM splash screen after a few days. This second one - I have had it ONE night - and the same thing has happened with incomplete booting. This time I have been trying all night to flash the phone to an official ROM, but I cannot do it (apparently) because I can't establish a connection via ActiveSync. When I stick the data cable in while in bootloader I see SERIAL replaced by USB and when I try the flash I get a "270" error (cannot connect to phone) and the phone re-boots to the sticking plash screen. What should I do now?

ladies and gentlemen...
we've got a lot of mixed messages in this thread.. please make sure you're posting the right thing. no need to disable USB when manually going in to bootloader to flash (at least in xp).. Also, you can ignore the part of the RUU that says 'do not manually enter bootloader' (you should really read the guide on my site)
foxuniform- can you please give some details..
1) are you running xp or vista
2) have you flashed hard-spl? if so what version?
in the mean time, try a couple of things.. first, flash hard-spl (even if you already have it, but from the sound of it i think you don't have it on your device).. if that works, try to flash an official ROM. Can also try to use splxploit, then flash hard-spl, and then flash official ROM (there's a guide on my site if you're unsure)
please post your results
*edit*
here are the steps for SD card upgrade, but i HIGHLY recommend flashing Hard-spl first..
try to do it from SD card. how?
Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (http://www.cabextract.org.uk/) .
Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
When flashing completes soft-reset your device.
Make sure your SD has FAT32 and has no label. There have been reports that if SD has a label the bootloader can not access the TRINIMG.nbh

racerx_ I have carefully read your response and suggestions, and thanks for your expertise input on the matter. I am fairly new to this stuff so read below carefully as you may find errors in the way I tried to go about doing what I was hoping to accomplish.
First let me answer your questions. I am running Windows XP. The phone is in it's completely natural state in that I have not flashed it in any way. The ROM I was TRYING to flash to the phone while it was not starting properly (this is where I manually entered bootloader) is an official ROM from the HTC website (please note everyone that when I registered my P3600i on the HTC website it came up as the Dopod 810). Anyway, that never worked. ActiveSync never detected the phone (and I guess that's the reason I could not do anything as far as flashing goes). I HARD-RESET my P3600i and it booted normally. I re-installed all the stuff I had on it, from memory card to various .cab files, and the phone is working beautifully thus far. I will report if anything funny happens again.
I have to ask you racerx_, if I CAN flash hard-SPL on the P3600i according to the lovely guide on www.trinityguides.info. I have been of the opinion that things don't work for the P3600i as they did for the P3600, and that has been echoed by many P3600i users on this forum who are ready and waiting to try out some cooked ROMs (myself included).
For the sake of record, my phone is running rom version 3.00.707.17 and radio version 1.46.00.11. I patiently await your response.

woaaahhh..
i didn't notice the 'i' in your previous post... yeah, as far as i know, these ROMs are not flashable on your p3600i.. sorry..
**correct me if i'm wrong somebody**

Yeah I kinda thought that would be your response. By the way - do you think that this phenomenon of sticking at the Windows Mobile splash screen (both the P3600 and P3600i models apparently) has anything to do with something users do with the devices, or you figure it's an inherent software glitch of some sort? I am wondering if I should try a different model or hold on to my P3600i? Hope it's not something that'll happen again - I fly for a living and it's not gonna be good to have the thing screw up on me away from base - I really count on it for everything from casual keeping in touch on Messenger to viewing my work schedule. I love the Trinity though - it's one of my all-time favourite HTC phones.

hmm... i don't think its inherent in the Trinity.. (not a hardware issue.. in my opinion)
its been a while since i followed the posts on it, but always seems to be software related.. sometimes ROM-specific problem. Personally, i've probably flashed as many ROMs as anyone and the only time i ever encountered problems was with the official HTC WM6 ha.. go figure.. I think ppl did find that hard resets before and after flashing are helpful as well..
i love my trinity, and there's not much else on the market to make me want to trade it in (is it just me, or have pda's kind of stopped getting cooler).. i'd stick with it..

HTC desire 2.2 HELP please

Ok so, this is my first android phone and after being prompted to install the 2.2 update on my European htc desire, i downloaded and started it installing. It gets to about 23% and says process system unavailible and after reading what people said i cleared the phone and tried to install the update manually from the SD card. This didn't work
My phone currently does this
Will boot into what it says is 2.2 but with no wifi, no service, and no SD card showing up
then after about 5 minutes it will reboot.
I have no idea what i can do to fix this? could someone please help me, i'm a noob with android so a clear step by step would be much appreciated

anyone

I am having the same issue... Anyone some help please...

I had a symetrical experience.. I can't post links yet, but you if you look at my posts you should be able to find what worked for me.

Futurian said:
I had a symetrical experience.. I can't post links yet, but you if you look at my posts you should be able to find what worked for me.
Click to expand...
Click to collapse
how did you create a blank goldcard, i can't access my SD card on my phone while it's in the phone so how did you do it

Do you have a WIFI connection? I do, and did the OTA 2.2 upgrade over WiFi with no problems, on my Unbranded European HTC Desire.
If youre phone won't boot properly, there are a few answers; 1) Return in to HTC, they're getit working and back to you, 2) Return it to th place of purchase, 3) Root/reflash (but sounds like it might not be an option).
Dale

F3L1X1 said:
how did you create a blank goldcard, i can't access my SD card on my phone while it's in the phone so how did you do it
Click to expand...
Click to collapse
I followed the instuctions in the "[TUT]Complete upgrading guide(root, unroot, flashing ROM & updates)" thread within Desire Android Development. (Post #3)
dedlite said:
Do you have a WIFI connection? I do, and did the OTA 2.2 upgrade over WiFi with no problems, on my Unbranded European HTC Desire.
If youre phone won't boot properly, there are a few answers; 1) Return in to HTC, they're getit working and back to you, 2) Return it to th place of purchase, 3) Root/reflash (but sounds like it might not be an option).
Dale
Click to expand...
Click to collapse
When I got in touch with HTC they wanted £50 to do a reflash, falsely accusing me of rooting my device..

was that 50$ to send it to them? or can they do it without having it there. Because if THEIR update screwed up my phone i don't see why i should have to pay for a fix

maybe a silly question but did you try a factory reset?
http://www.htc.com/www/howto.aspx?id=805&type=1&p_id=312

HugoTouchHD said:
maybe a silly question but did you try a factory reset?
http://www.htc.com/www/howto.aspx?id=805&type=1&p_id=312
Click to expand...
Click to collapse
yeah i did that, about the only advice the australian HTC support guy gave me -____-

F3L1X1 said:
was that 50$ to send it to them? or can they do it without having it there. Because if THEIR update screwed up my phone i don't see why i should have to pay for a fix
Click to expand...
Click to collapse
Tell me about it, so thankful I managed to fix it myself!

It sounds like you are alll applying an OTA update for the standard ROM to what was a branded device. There are lots of explanations as to how to fix this if this is the case
In summary
Download update from mentioned here
Copy this to root of your goldcard and rename to update.zip
Turn off phone
Turn on holding down vol down
Select Bootloader then Recovery (an image of device should appear with exclamation mark over)
In menu (sorry forgot how you get in, if it does not appear then try power+vol down or power + back). From there choose apply update.zip
Wait while update applied
After update select reboot and wait for device to boot
Video of it here

jameson_uk said:
It sounds like you are alll applying an OTA update for the standard ROM to what was a branded device. There are lots of explanations as to how to fix this if this is the case
In summary
Download update from mentioned here
Copy this to root of your goldcard and rename to update.zip
Turn off phone
Turn on holding down vol down
Select Bootloader then Recovery (an image of device should appear with exclamation mark over)
In menu (sorry forgot how you get in, if it does not appear then try power+vol down or power + back). From there choose apply update.zip
Wait while update applied
After update select reboot and wait for device to boot
Video of it here
Click to expand...
Click to collapse
I've just tried this again, installation looked like it went through ok, rebooted and relaoded into sense, then it shows me a status bar counting, normally this gets to about 10% then says ?Sorry process system is not responing, so i can either click wait or force close, then in continues upto about 97% then reboots and reloads only to load a white screen showing htc and continues counting in percentages, gets to about 15% then says force close, then onto about 91% then reboots this goes on for a while until it just shows me a sorta bricked phone with no wifi, gsm or any real functionailty and it continues to reboot every 5 mins, back to where I started showing 2.2 as installed
One strange thing I have noticed is that my CID is
CID: 00000000000000000049E917D100A69E
Reversing CID
CID: 00A600D117E949000000000000000000

Can't find update.zip on SD card during recovery
Tried all this, thanks. Goldcard created using Gold Card Tool 0.0.5 (awesome job Klutsh) . I get the error message:
"E:failed to open /sdcard/update.zip (No such file or directory)" even though it is in the root dir when I look at the card on my PC.
Should it be in a directory called /sdcard ?

chessmaster82 said:
I've just tried this again, installation looked like it went through ok, rebooted and relaoded into sense, then it shows me a status bar counting, normally this gets to about 10% then says ?Sorry process system is not responing, so i can either click wait or force close, then in continues upto about 97% then reboots and reloads only to load a white screen showing htc and continues counting in percentages, gets to about 15% then says force close, then onto about 91% then reboots this goes on for a while until it just shows me a sorta bricked phone with no wifi, gsm or any real functionailty and it continues to reboot every 5 mins, back to where I started showing 2.2 as installed
One strange thing I have noticed is that my CID is
CID: 00000000000000000049E917D100A69E
Reversing CID
CID: 00A600D117E949000000000000000000
Click to expand...
Click to collapse
i get this same problem. How do i create a gold card if when i plug in my phone to my pc it won't recognise it and when i put the SD in the phone the bricked 2.2 won't recognise it

F3L1X1 said:
i get this same problem. How do i create a gold card if when i plug in my phone to my pc it won't recognise it and when i put the SD in the phone the bricked 2.2 won't recognise it
Click to expand...
Click to collapse
I had to format the card in a card reader in my PC, then use the Gold Card Creator mentioned elsewhere in the thread. You have to install HTC Sync because enough drivers are in there to at least allow the apps to 'see' the card at physical level, even if the bricked Android doesn't. Set the phone to USB debug mode in Settings/Applications - the phone stays 'on' long enough between reboots to do that and get a CID out of it! Then Gold Card Creator works well enough to get the CID from the SD.
I'm trying this again with a 2GB card to see if makes any difference.

Check folder settings when using windows
bearMedicine said:
Tried all this, thanks. Goldcard created using Gold Card Tool 0.0.5 (awesome job Klutsh) . I get the error message:
"E:failed to open /sdcard/update.zip (No such file or directory)" even though it is in the root dir when I look at the card on my PC.
Should it be in a directory called /sdcard ?
Click to expand...
Click to collapse
Quick update to this. Make sure you have extensions of known file types SHOWING in your folder settings. I was naming the file update.zip.zip!!
Thanks to ALL in this forum for get apps and assistance. I unbricked my phone tonight thanks to you all

well i phoned the shop here in australia that i bought it from and they said they've had alot of desires being returned because they've been bricked by the update and to just send it back and they'll fix it and update to 2.2 for me

sound?

hi there
i just managed to install android onto a HTC "Kaiser" TyTn2.
everything i need seems to work fine except sound and wifi.
i installed RLS15 from http://forum.xda-developers.com/showthread.php?t=759894
using KaiserCustomRUU.exe
now there seems to be no sound. i called a number, and i hear nothing at all. i tried pressing speaker, and same no sound. vibrates working though. i also tried pulling the vibrate tab but it didnt work. still no sound.
about wifi, i have a Ad-Hoc network from my computer (which i can connect to from my ipod touch 3g - iOS4), but even after turning Wifi on in settings, it just doesnt seem to see my network....
btw i got no "welcome to android" or set up or anything... i did hold the DPad
any help?

I'm not sure but try out another Radio http://forum.xda-developers.com/showthread.php?p=9807696#post9807696 <---- Here
Flash it with HARDSPL or just using CustomRUU when in the tri-color screen.
I could be wrong but that's what I'm guessing
Wi-Fi... Wich kernel did you use?
Try out http://forum.xda-developers.com/showthread.php?p=9807696#post9807696 Post 118
And use the Androidupdate I attached, It's the one from Liquid wich should fix the Wi-Fi
Let us know if it fixed it
(God i had to edit it a million times before i did it right )

calls do definately go out. i called someone, i coudnt hear anything, and they called me back.

What do you mean by "Welcome To Android" ?

i read in some website that the first screen when booting android for the first time is Welcome to Android

Gaura Mohana said:
i read in some website that the first screen when booting android for the first time is Welcome to Android
Click to expand...
Click to collapse
In some builds, when you boot Android, it gives this kind of tutorial on how to use your phone (Wich has as title "Welcome to full android on Kaiser" for example), time and date settings and connect to Google account, It's possible that it isn't in the one you use
Don't worry about it, the welcome to android doesn't show when u press D-pad, the D-pad is to get into the menu when ur kernel is booting (the one with black background and white letters)
The menu is to install your system, make backups, clear dalvik and others

ok... but what do i do now about the sound? (and the wifi if posibble)

Gaura Mohana said:
ok... but what do i do now about the sound? (and the wifi if posibble)
Click to expand...
Click to collapse
Sound=New Radio
Wi-Fi is probably androidupdate
[SOUND]
Go to http://forum.xda-developers.com/showthread.php?t=393182
Scroll down until you see this: KAISER Radios These Radios were ripped from Kaiser WM6.1 ROMs.
Pick a radio and download it.
HARDSPL IS NEEDED FOR THE RADIO!
Extract the file and change the name from the NBH file to KAISIMG.NBH if the name is something else.
Copy KAISIMG.NBH onto the root of your sdcard and plug your sd card into the phone.
Hold down the camera button and turn the device on or reset it.
When you see a tri-colored screen, release the camera button.
When you see a blue text with something like RADIO (i guess) press the power button (just 1 little press, no long pressing)
The device will now update your RADIO, when finished just reset it.
Now reinstall your Android version by holding down the D-center button when asked, then selecting Install System and make it clear data.
[Wi-Fi]
Copy the androidupdate.tgz into your Andboot folder
Reboot the phone and press D-center button when asked
Choose the option to install update
Wait for it to finish and just press quit to boot Android

OMG DUDE!! thank you so much

Gaura Mohana said:
OMG DUDE!! thank you so much
Click to expand...
Click to collapse
no problem
hope it works

i just managed to put the KAIS_RADIO_ONLY_1.71.09.01.nbh (which i renamed to KAISIMG.NBH) and i put it on the root after a couple of hours figuring out how to make the phone show up in explorer
i tried starting exactly as you told me, but it boots directly to android - no tricolor. it worked fine before i installed android. so what do i do now?

Gaura Mohana said:
i just managed to put the KAIS_RADIO_ONLY_1.71.09.01.nbh (which i renamed to KAISIMG.NBH) and i put it on the root after a couple of hours figuring out how to make the phone show up in explorer
i tried starting exactly as you told me, but it boots directly to android - no tricolor. it worked fine before i installed android. so what do i do now?
Click to expand...
Click to collapse
I don't think there's another way, just, turn phone off, hold camera button in while pressing the power button once
Release the camera button after you see the colored screen
http://www.youtube.com/watch?v=bVMeZyuIMls
Doesn't show much more than I already said
Did you put hardspl on it anyways?

Thanks... What i managed to do was to simply get into the tricolors by holding power+home, then i connected to computer, and SPL'ed from CustomRUU. it worked, and sound is working. i tried your way but it woudnt detect my .NBH. thanks anyways
but where can i get a androidupdate.tar for the wifi for?
btw quick point, but my camera seems to work!!!! i remember reading that the camera WONT work on android. (it didnt work before installing the latest radio)

Thanks for the file. i just tried installing the liquid update from this post, and all i get is error under wifi (before wifi would turn on - but it kept on searching and found nothing). i did install a old update before this. could that have messed it up?
i also have a problem with USB mounting. I click turn on USB storage, and it works randomly. it works 1 time - doesnt work 10... replkuggin and stuff doesnt work. as in "Android Phone" is showing in Eject, but nothing is showing in explorer
EDIT
-----------------------
I just re-installed android and now installed the liquid update.
NOW wifi turns on, but it just scans (has been scanning for 5 minutes)
my ipod touch sees the network immediately.

Gaura Mohana said:
Thanks for the file. i just tried installing the liquid update from this post, and all i get is error under wifi (before wifi would turn on - but it kept on searching and found nothing). i did install a old update before this. could that have messed it up?
i also have a problem with USB mounting. I click turn on USB storage, and it works randomly. it works 1 time - doesnt work 10... replkuggin and stuff doesnt work. as in "Android Phone" is showing in Eject, but nothing is showing in explorer
EDIT
-----------------------
I just re-installed android and now installed the liquid update.
NOW wifi turns on, but it just scans (has been scanning for 5 minutes)
my ipod touch sees the network immediately.
Click to expand...
Click to collapse
Hmm can you tell me wich kernel you are using? 2.6.32?
Did you use the guide on Atools to make your nbh files?
Guide: http://forum.xda-developers.com/showthread.php?t=783514
Gotta go take exam right now so I'll be looking for this afterwards.
And since it's 06:24 here in the morning, we have a bit of a time issue I think.

I actually dont know what version i have, but i got it from some post on this forum, and it was the latest, and i did use atools.
I found this post http://www.google.com/support/forum/p/android/thread?tid=3b250c94811ca5df&hl=en
I am trying to use a ad-hoc network too, and i dont have any other type of wifi to try.
thanks
good luck with the exams(s)
EDIT- i have 2.6.32.9

Gaura Mohana said:
I actually dont know what version i have, but i got it from some post on this forum, and it was the latest, and i did use atools.
I found this post http://www.google.com/support/forum/p/android/thread?tid=3b250c94811ca5df&hl=en
I am trying to use a ad-hoc network too, and i dont have any other type of wifi to try.
thanks
good luck with the exams(s)
EDIT- i have 2.6.32.9
Click to expand...
Click to collapse
It could be that it's not possible to connect to an ad-hoc network, I've got no idea about that.
Hope someone else will post here and answer that.
U should really try connecting with a normal Wi-Fi network
Go onto the street and look for appartments or houses with open networks just to test?

i live in a small town..... no one here has internet let alone wifi....

aww that's balls
got no idea on how to try it then

[Q] HTC Wildfire TOUHC panel - FAIL

Hey my HTC Wildfire screen stopped working whan i went to boot menu i saw that there writes "TOUCH PANEL - fail". I know that its possible to fix it via flashing a new rom, but how can i do this without clockwork mod ? My phone have only stock adroid recovery.. also debugging is standart type i dk on or off. So please help to reslove this problem.
Maybe this goude can fix my phone http://forum.xda-developers.com/showthread.php?t=1162971 ?
Thanks for posting and helping.

If it says that in the recovery boot menu it may well be faulty.
You could try making a gold card then flash an official ruu.

pls give me a link how to make everything i am a huge noob in telephone software..

http://forum.xda-developers.com/showthread.php?t=1074445
[ROM]Shipped Marvel ROM Collection
Check the above link to get the rom you need.
Then Google easy goldcard creator

Or your under warranty it might be better for you to send for repair.

That happens to my old Wildfire S. Both the screen and home buttons went and I couldn't do anything. I returned it as I only had it for 3 weeks and they gave me a new one, No issues with it since. I have read around the net that people have had the same issues with the phone and it's just faulty. I have had my new one for 4 months and it hasn't had an issue...

Yeah my first one had a problem with the touch screen. When charging and using the touch screen it would do some crazy stuff like moving all my icons, scrolling pages etc.
Only had it a day then called my provider who sent a new one.
Had this one about 7 months and its perfect.
My son has one and it has a bad power button, have to press it 3 to 4 times to wake the phone. Seems to be common to the sensation.

I will not change my telephone, becouse i can't.. any more ideas how can i flash a new rom ?

choisYA said:
I will not change my telephone, becouse i can't.. any more ideas how can i flash a new rom ?
Click to expand...
Click to collapse
Check the link above and Google "goldcard"

I dont know what is wrong but when i connect my phone to computer the mircro sd card folder in My Computer doesn't appear... Also i have installed htc sync and got same problem in program writes that no connected any ideas ?

choisYA said:
I dont know what is wrong but when i connect my phone to computer the mircro sd card folder in My Computer doesn't appear... Also i have installed htc sync and got same problem in program writes that no connected any ideas ?
Click to expand...
Click to collapse
Go to your phones settings
Then look for 'connect to PC'
Then tick the box that says ask me or change default connection type.
Alternative is when connected to PC drag the notification bar down and you'll see USB connection, click it and choose required connection.
If it helped hit the thanks button.

why dont you read the all theme ? I can't unlock my phone i can't do anything just go to boot menu i turn it is everything good but it doesn't unlock becouse my touch panel is fail.

then basically your [email protected]@@ed SEND IT BACK

Just a thought but in the hboot menu have your tried "Clear Storage" ?

Tera Tike said:
Just a thought but in the hboot menu have your tried "Clear Storage" ?
Click to expand...
Click to collapse
yes ofc. Hmm tomorrow i will try to make a gold card, please give me any more solutions, thanks.

LineageOS for Oneplus One and problem with wifi and HDR in camera.

Hello everyone.
I have 2 problems with LineageOS on Oneplus One.
First HDR does not work properly. I can not do a photo with HDR enabled.
My another problem is with WIFI. Many times I have lost connection to internet without report, and I must reconnect manually. My phone is connected to router but without internet. It is very annoying problem for me.
I fashed:
lineage-14.1-20170206-nightly-bullhead-signed.zip,
Gapps Android 7.1/Lineage os ARM Pico ( other did not work because of low free space of disk. I have 50 gb free. Weird )
Latest Super Su.zip
I flashed them all at once. Was it good idea? Or I should flash them separately ?
Of course I did clean wipe before installation and Wipe Dalvik,cache after installation.
Thanks for replies

I have the same problem with the wifi... i don't know if it is a firmware / modem problem... i have this version: "2015_05-15_DI.3.0.c6-00241"
The camera problem its reported and with be resolved in the future...

And another problem. My phone has not been detected by computer. I can not transfer music
Any idea to solve it? There is an icon "eject MTTP" but no folder with phone on my computer.
File transfer is not working, but photo is working. Weird
I solved problem with the wifi. Just instal the latest room
Hi.
I don't why this worked for me or if it might even work for you, but what I did was locate the following file 'wpdmtp' in C:\Windows\INF.
I right-clicked on it and updated it.
Suddenly, my PC recognised my Lumia 535, even though if I try to update the driver I still get the same error.
Well, as long as my phone shows up, I don't really care. Hope that helps.
Click to expand...
Click to collapse