Related
Hello Everyone,
I will try to provide as much details as I can from what I remember.
Basically, I tried to ROOT my device and install TWRP. However, I messed it up the first time. I tinkered with it for hours but it still couldn't work until finally, after hard resetting for the unlimited time, it booted up.
The problem though, is that it wasn't rooted and TWRP wasn't installed when it came up so I tried it again. Second try, second time it was messed up. Annoyingly, I don't know what I did earlier to make it work. The second instance it happened is just like the first.
Just to be clear, this isn't the boot screen where the kindle fire logo is animated (has reflections). In my case, its the logo as is, stuck on the screen just like that. Tried hard resetting, doesn't work.
What do I know?
1) From my earlier experience, it has lesser to do with the system (PC, Mac) and drivers since I managed to get it boot up again without being connected the first time
2) If I do connect it to the PC, it says Cannot Start Device/Unable to Start Device. Code:10. That's it. Even if I reboot the device, its still the same.
3) If you connect it to the Mac, it is detected in system preferences. Problem though is that I tried using adb and just like its windows counterpart, there are no devices detected.
THOUHGTS:
1) I know I just have to get it to be recognized and I can change the bootmode. Something's telling me that its a boot mode problem only. In my earlier V3X phone, I used to TP (testpoint) if anyone's familiar with that, or shortcircuit the board to get it out of the 'loop'. Do we have that with the kindle fire?
2) What operating system would it be easiest to get the device detected. I'm hoping that if there's lesser complications with the device being detected by the computer, be it mac, linux or windows, I can change the bootmode. my technical instinct tells me it has something to do with boot mode.
What have I done already?
1. Let me see, I believe I tried hard resetting it for ALOT of times already
2. Reinstalled drivers on PC. Used both Android and Kindle Fire Utility drivers. Even checked the /android folder
3. I'm using a Nokia Micro-USB cable. I'm not sure if that has any impact on the device or its effectiveness but I will try to pick-up another cable today and post later.
I would really appreciate if anyone can help. It sucks that I tried this just after unboxing the unit. I haven't even tried doing anything on it yet.
If you can help, ANY help would be appreciated.
Thanks mate!
had the same
1. use computer (windows - in my case windows xp)
2. nokia cable is fine (i use it too)
3. use kf utility .6
is your kf recognized by the computer ? (adb device or composite adm device)
have you tried to shutdown and startup your computer ? (not restart)
the entry for 18D1 in adb_usb.ini is missing - had to add it
the other entries are allready in version .6 android_winusb.inf
if you have troubles to remove old drivers use this:
http://support.microsoft.com/kb/315539/en-us
unplug/replug and install the drivers from .6 from scratch
it's not needed to reboot the computer - works immediately
waiting to get your status ...
b63 said:
had the same
1. use computer (windows - in my case windows xp)
2. nokia cable is fine (i use it too)
3. use kf utility .6
is your kf recognized by the computer ? (adb device or composite adm device)
have you tried to shutdown and startup your computer ? (not restart)
waiting to get your status ...
Click to expand...
Click to collapse
Did you solve your problem?
My kindle is recognized by my computer but it as either ADB device or Composite ADB device (depending on what drivers I use to install it). Problem is that it says Cannot start device. Code Error: 10. Tried shutting down/restarting PC, still the same.
updated my initial post again ... (ms-link)
yes solved it in minutes
make the additional entry in adb_usb.ini
use only the drivers from .6
i think best way is to disconnect the kf - uninstall all old drivers regarding adb device - connect kf - use only drivers from .6 utility - start utility - change bootmode - up again !
whats your status ?
i think best way is to disconnect the kf - uninstall all old drivers regarding adb device - connect kf - use only drivers from .6 utility - start utility - change bootmode - up again !
Click to expand...
Click to collapse
I did this but it still says device cannot be started.
make the additional entry in adb_usb.ini
Click to expand...
Click to collapse
0x18D1 -- is that what I'm supposed to add to adb_usb.ini?
yes exactly - the device changes between the two id's regarding the bootmode
and don't let the computer select the driver - select manually
b63 said:
yes exactly - the device changes between the two id's regarding the bootmode
and don't let the computer select the driver - select manually
Click to expand...
Click to collapse
Okay, so I followed the instructions to a T.
I followed the MS Link to remove all drivers and then plugged-in the kindle and installed it back again by specifically telling windows that 'I have a disk'. It still says Code 10.
If it would mean anything, I'm doing this on a virtual machine since the computers around me are all Windows 7s.
kaswistry said:
Okay, so I followed the instructions to a T.
I followed the MS Link to remove all drivers and then plugged-in the kindle and installed it back again by specifically telling windows that 'I have a disk'. It still says Code 10.
If it would mean anything, I'm doing this on a virtual machine since the computers around me are all Windows 7s.
Click to expand...
Click to collapse
all this works using windows 7
dustyjerran said:
all this works using windows 7
Click to expand...
Click to collapse
I did try this yesterday on Windows 7 but most guides I see do it on older versions. I will try again a little later. Thank you.
I tried it on Windows 7. Still the same error. Kindle is frozen and on Device Manager it says "This device cannot start. (Code 10)"
I ran into the exact problem yesterday. I thought I bricked my kindle. That was scary. Anyway, the problem is that you're stuck on fastboot, mode 4002 instead of a normal mode 4000.
Following rootzwiki.com/topic/12363-how-to-windows-install-twrp-20-on-your-kindle-fire/
You'll need to add a new vendor id (0x18d1). However, even with that the device still will not be recognized right away. Following another user's suggestion on that same thread, I let the battery drained out. Once that's done, reconnecting the Kindle will show up as simply "kindle" on the device manager instead of the normal "unrecognized device".
Then do the adb commands (even if it doesn't show any device attached)
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
Click to expand...
Click to collapse
Your device will reboot out of the stuck "kindle fire" logo screen. If your device goes dark after, it just means that the battery need to recharged first. Another scary moment for me. You can unplug and use the wall charger, much faster than charging by PC. After 5 - 10 minutes, you should get back to your normal screen. Then, just use the Kindle Utility to install TWRP.
You'll need to add a new vendor id (0x18d1).
Click to expand...
Click to collapse
I added this already
reconnecting the Kindle will show up as simply "kindle" on the device manager instead of the normal "unrecognized device".
Click to expand...
Click to collapse
Actually, the problem with mine is that it's detected. However, it shows up as Code:10, The device is unable to start.
Still, I'll try to drain it first, tinker with it next and see what happens. That or I'll wait for tomorrow and open the whole device already and see if I can OMAP it.
Mine also did show up as code 10, and sometimes code 43 ... I tried uninstalled the driver and reinstall it manually each time and eventually showed up as unrecognized ... so I tried the battery drain ... I even tried putting it in the freezer to quicken the drain but not sure if it actually help ..
I tried the battery draining. Nope, still didn't work
UPDATE: I take this back. After draining the battery, I would like to confirm that the issue has been fixed. Thank you, THANK YOU Everyone! )
I REALLY APPRECIATE THE EFFORT. HAPPY HOLIDAYS! )
A family member recently got a Kindle Fire, I tried to flash recovery but it got stuck in fastboot mode. Windows will recognize it as uknown device but Linux won't detect anything in fastboot or adb.
I will try battery drain out since kaswistry said it worked
If all else fails, I will try this.. http://forum.xda-developers.com/showthread.php?t=1405052
EDIT: nevermind lol, this worked.. http://forum.xda-developers.com/showpost.php?p=20619033&postcount=11 even though i tried it several times already..
I have the same problem too, the kindle fire stuck at the boot logo
kf utility show that when i try to restore or other option!
Changing bootmode doesent work at all
*imageshack/photo/my-images/10/60506677.png/[/url] (imageshack link)
KF utility status fastboot... offline
*imageshack/photo/my-images/834/kfustatus.png/
My computer have the right driver!
can anybody help me?
*sorry for my bad english*
Could it be that something destroyed my FireFireFire boot? My KF always gets stuck in fastboot when I try to flash ... obviously quite annoying.
u guys need to talk to vashypool in irc and he can fix it!! he fixed mine and mine was a complete brick
If it gets stuck in fastboot you need to run the command fastboot idme bootmode 4000 from the Android SDK.
Sent from my Kindle Fire using Tapatalk
In my case, i have tried to install the original 6.2 kindle firmware with TWRP. After that, the kindle staying stuck on the boot logo... This is me story... I think my kindle is stuck on fastboot! I tried to change bootmod with FK utility v.6
This is what kf utility gave me, when i try to reinstall twrp
imageshack.us/photo/my-images/10/60506677.png/
And this is the kf utility status
imageshack.us/photo/my-images/834/kfustatus.png/
Is anybody can say me, if my kindle is bricked for ever? Or have a solution
Happy holiday btw
#sorry for my poor english#
1) Yes I checked search results.
2) Yes I've googled.
3) Yes I've tried the Kindle Fire Utility, the http://forum.xda-developers.com/showthread.php?t=1356257... links options.
With that being said, here's my issue;
Got a KF a couple days ago...
Yesterday, followed some online instructions to put GO Launcher EX on there to replace the carousel deal.
Followed instructions to the T.
Restarted. Got to "Choose your OS" screen (or whatever it precisely says...)
Picked GO... then it froze.
Now, when it restarts (yes, its the 30 second hard restart), it gets stuck on the Kindle Fire splash screen.
I have tried the above utilities.
I have hard restarted.
I have fully charged and ran the battery dry and tried again.
When I use the utilities, the problem is, my PC will not recognize the Kindle (it see's it as a removable storage device, but it doesn't click over to 'Kindle', and thus the utilities can't interact with the device itself, I suppose).
I've tried different USB ports and connecters (I have 2 regular kindles in the house, too). But I know all the peripherals work through cross-testing.
Essentially, what else can I do? (I got it from WalMart, and they're currently out of stock, so I can't return it till next week, but I'd like it fixed before then if possible)
I've tried several different methods from these forums too, but I *always* hit the same snag... whenever any utility is 'waiting for device', it simply will not find it, because the PC doesn't see it properly. It sees *something* (removable storage) but not as a kindle, and thus won't allow the utilities to interface with it.
Are there any physical things I can do to hard reset it without destroying any warrantys?
Any help appreciated!
there is no need to return it
from what you say i think you have a bad launcher on it and the kf tries to start it but can't
first i need to know if you have fff (custom bootloader - yellow triangle) on it ?
then do you have a recovery (twrp) on it ?
what os/bit of computer ?
In kindle utility go to bootmodes and enter normal (4000). Just had that problem last night.
awidawad - I've tried that. It stays on 'waiting for device' forever. Please explain step by step what you did? At which point did you power on the KF, when did you run KFU, etc, etc.
b63 - I hope your right!
no - I do not have the yellow triangle.
no - I do not have TWRP on it, i have tried, but cannot get anything onto the kindle.
my PC is window7, 64bit
Euryon said:
awidawad - I've tried that. It stays on 'waiting for device' forever. Please explain step by step what you did? At which point did you power on the KF, when did you run KFU, etc, etc.
Click to expand...
Click to collapse
Do you have all the kf drivers installed on your computer? I know that when I unbricked mine I had all the drivers installed but I had to reinstall them for some reason. If you do not have them I can post them later on tonight when I'm at home. However, I have TWRP installed on mine, and Cyanogenmod 7.2, so hopefully yours is able to connect to your computer.
---------- Post added at 12:56 PM ---------- Previous post was at 12:50 PM ----------
b63 said:
there is no need to return it
from what you say i think you have a bad launcher on it and the kf tries to start it but can't
Click to expand...
Click to collapse
In order to remove the bad launcher, you need to have your device connected to your computer to remove it using adb.
ok so b63 helped me out big time here....
about 2 hours ago we got on a teamviewer session (download this if you want these guys to help you with serious issues!)
took me a minute to figure out how to allow him/her proper access to my screen
anyway
i don't understand the technical stuff
but
what i had done wrong is that i didnt root the KF before trying to install the GO... software (i think)
b63 had a heck of a time trying to discern the problem with me being about as useful as a dead fish, but get there he/she did
after much fanangaling, b63 managed to install the TWRP and ADP on my KF, allowing it to fastboot, and basically allowing it to be read by my PC, and so fixed.
im sure it would have taken b63 all of 5 minutes in real time, but using the quirky teamview and my slow net speed didn't help
still, thanks VERY MUCH to b63 for fixing the **** out of my KF, and being very helpful and patient all along!
thanks
Just wanted to drop b63 a note here that I "thanks"ed their post above - not necessarily for the post but for going above and beyond. The people on these forums are (for the most part) really great. (Too bad there have to be a few who are demanding of the developers to get this feature or that fix done faster without taking into account that the devs do this all in their free time.)
YES, search finally led me here!
Euryon, I have the exact same thing happening with my KF right now.
Do you remember any specifics of how b63 carried out the steps you listed?
b63, any chance you could help me with mine? My issue is identical with Euryon's down to the letter.
Same Problem
Could someone please help me i have the same problem
same problem here! please can someone give a step by step? My fire is unrooted and I did nothing to it except try to install the go launcher and after I selected it as the default launcher it got stuck at the kindke fire logo.
I tried the Kindle unbricking utility but it cannot find the device even after I installed the adb composite interface
also, my fire is not showing up as a kindle - it is showing up as an android device.
rollno88 said:
also, my fire is not showing up as a kindle - it is showing up as an android device.
Click to expand...
Click to collapse
Have you added the fires usb ID to your system?
Sent from my Amazon Kindle Fire using Tapatalk 2
thanks for replying, and I have no clue how to do that. I'll search and get back .
---------- Post added at 10:12 AM ---------- Previous post was at 09:57 AM ----------
okay, I already did that by editing the android sdk(as a prerequisite to rooting, which I planned to do eventually) - so when I connect my fire it first shows up as a kindle, and after updating the software through windows and installing drivers through KFU, it comes up as an android device and the interface is adb composite. Now if I try to install TWRP through KFU it keeps switching between adb composite interface and plain adb. And both KFU and KUFU keep waiting but are unable to find my device.
also, my fire alternately shows up as a usb composite device and an android device. PLEASE help
okay I solved it with KFU (finally!) although I have no clue how I did it as I didn'tdo anything I hadn't tried earlier so, managed to install TWRP and then wiped everything and finally my fire could be read - then I deleted go launcher and now my fire is back from the grave
A big thank you to all the helpful posts at this forum - u guys are the best
Same issue
Tried rooting my KF, but couldn't change permissions and thus could not install android market. Superuser didn't do anything other than show me a log folder that had no logs. Tried to change permissions on /system and /apps with one of the file management apps on amazon and it said the device *wasn't* rooted, despite GO launcher and android interface.
Did a factory wipe to try to reroot or fully(?) root the KF, and that's when it all went wrong. Got stuck on boot loop, but KFU helped me break out of that. Now it's stuck on the Kindle Fire splash screen with no animation. I read somewhere that this was the fastboot getting "stuck."
At any rate, i have TWRP 2.0 installed and can mount and unmount the device in its interface, but it is only recognized as ADB android device, or when mounted via TWRP, USB composite device. As such, ADB commands only work occasionally - all other times it simply says <waiting for device>.
I am running Windows 7 64 bit, and 6.3 on the KF. All restarts on the KF are hard restarts, except occasionally cmd lets me fastboot reboot.
I have spent the past 2 days trying everything I have found online (2 KF unbrick applets, 15+ tabbed browsers with different threads) to no avail. I am finally posting, pleading for assistance.
Thanks in advance for any (helpful) replies. Real thanks clicking afterwards.
edit: when rerunning KFU, i kept getting the message that many execs failed because "/system/bin/sh" directory does not exist.
I don't know if that helps narrow down what might be happening, but I saw that coming up a lot in the cmd prompt.
zeissbickham said:
Tried rooting my KF, but couldn't change permissions and thus could not install android market. Superuser didn't do anything other than show me a log folder that had no logs. Tried to change permissions on /system and /apps with one of the file management apps on amazon and it said the device *wasn't* rooted, despite GO launcher and android interface.
Did a factory wipe to try to reroot or fully(?) root the KF, and that's when it all went wrong. Got stuck on boot loop, but KFU helped me break out of that. Now it's stuck on the Kindle Fire splash screen with no animation. I read somewhere that this was the fastboot getting "stuck."
At any rate, i have TWRP 2.0 installed and can mount and unmount the device in its interface, but it is only recognized as ADB android device, or when mounted via TWRP, USB composite device. As such, ADB commands only work occasionally - all other times it simply says <waiting for device>.
I am running Windows 7 64 bit, and 6.3 on the KF. All restarts on the KF are hard restarts, except occasionally cmd lets me fastboot reboot.
I have spent the past 2 days trying everything I have found online (2 KF unbrick applets, 15+ tabbed browsers with different threads) to no avail. I am finally posting, pleading for assistance.
Thanks in advance for any (helpful) replies. Real thanks clicking afterwards.
Click to expand...
Click to collapse
Read this...
http://forum.xda-developers.com/showthread.php?t=1552547
with an emphasis on post #2. You need to know what mode your device is in by looking at the device manager and make sure your drivers are loading correctly for that mode. If you can get to TWRP, you can mount your USB mass storage device, copy a new zip file of either the stock software or a custom ROM and flash it.
Thank you. I will be trying this shortly.
fully bricked
I followed the guide and got to a point where the Kindle Fire animation was playing. It loaded up to the unlock screen and then automatically shut itself down - would not stay on when either connected or disconnected. Tried installing a ROM but still shut down. Started the recovery and hit factory reset, still auto shutdown. Tried clearing a partition as described in the tutorial and now it's fully bricked. Will not turn on when connected to computer, to outlet, to another cable.
Thanks for trying to help.
UPDATE: I added "solved" to the title since I am now unbricked. That said, I do hope someone will pop in and tell me how to run the shell scripts on a mac...
Click to expand...
Click to collapse
Hi there. I have spent several days searching xda forums, popping into the kindlefire irc channel, and searching google however have not yet figured this out, could use some help.
I have read: the Kindle Fire Beginners Guide, the Kindle Fire Unbrick thread, The Kindle Fire Utility thread (yup the whole thing), and more.
According to the Kindle Fire Beginner's Guide, only 1% of all brick situations are actually a brick, so I'm going to persevere and go ahead and ask for the help, because also according to the guide, if your fire can't be seen as a device then actually it's a brick. To quote: " unless something else was done to the device after the change in bootmode preventing access to adb or fastboot commands. Then it’s actually a brick at that point."
I can't be sure if anything else was done after the change in bootmode so I'll just explain how I got here and hopefully someone can help out.
I have a mac mini running Os x 10.6.8, and the Kindle Fire which was running stock version 6.2.2.
I used the kindlewater root method to install firefirefire and cwm recovery. Was able to boot into recovery by pressing on the power button for it to go orange and then load the recovery options.
Before doing anything at all (and in consultation with St3p_2 of this forum, one of the kindlewater developers), I decided to perform a backup in preparation for flashing a ROM.
so, I booted, went into recovery, navigated to "install a .zip" and chose "backup" at which point I got a message/nag/reminder that this was a permanent change, and I selected "ok". It did it's thing for a while, went into reboot, and I then had the firefirefire logo blinking in a very very slow loop.
It was recommended to me to perform a factory reset by holding the power button for 2 solid minutes, which should then have returned me to stock. Actually, the first time i did it for minutes I went from having a very slow blinking firefirefire to having a rather fast blinking firefirefire. Following a suggestion i then tried it with the kindlefire unplugged. This resulted in a plain black screen until the fire was plugged in again: no boot, no indication of response to use of the power button. Once plugged in, it has gone back to the rather fast blinking firefirefire logo.
I read through the Kindle Fire Utility thread, found the v0.9.2 version prepared for mac and linux, and downloaded it. Although I am not new to terminal, I am not familiar with what command language is necessary to perform the actions required by this tool. If I open the install_drivers.sh with terminal, i get this:
Reverie:~ apple$ /kindlefire/Kindle_Fire_Utility_MacLinux_0.9-1.2/install_drivers.sh ; exit;
This file will install the correct adb_usb.ini file for proper Kindle Fire detection.
cp: drivers/adb_usb.ini: No such file or directory
Done!
logout
[Process completed]
so I tried running it in the console. I will spare you the output of the console as it appeared to be merely a printout of the actual code of the file and was quite long.
Trying to run the file runme.sh in terminal before running the install_drivers.sh in the console, I got error messages stating there is no such command, or no such file, depending on my command language.
After running the install_drivers.sh in the console, when I try to run runme.sh in terminal, i get this:
/kindlefire/runme.sh ; exit;
Reverie:~ apple$ /kindlefire/runme.sh ; exit;
---------------------------------------------------------------
Easy rooting toolkit (v1.0)
created by DooMLoRD
using exploit zergRush (Revolutionary Team)
Credits go to all those involved in making this possible!
---------------------------------------------------------------
[*] This script will:
(1) root ur device using zergRush exploit
(2) install Busybox (1.18.4)
(3) install SU files (3.0.5)
[*] Before u begin:
(1) make sure adb is in your path
(2) enable "USB DEBUGGING"
from (Menu\Settings\Applications\Development)
(3) enable "UNKNOWN SOURCES"
from (Menu\Settings\Applications)
(4) [OPTIONAL] increase screen timeout to 10 minutes
(5) connect USB cable to PHONE and then connect to PC
(6) skip "PC Companion Software" prompt on device
---------------------------------------------------------------
CONFIRM ALL THE ABOVE THEN
Press any key to continue... --- STARTING ----
--- WAITING FOR DEVICE
Which I affirmed because all the requirements had indeed been set that way on the device before the bricking happened. After "starting" and "waiting for device" nothing happens even waiting indefinitely (more than half an hour) and then it never finds the device.
When I go into terminal and type: "adb devices" I get:
Last login: Sun Mar 18 17:08:38 on ttys001
Reverie:~ apple$ adb devices
List of devices attached
Reverie:~ apple$
This result is the same both before attempting to use the 0.9.2 mac utility and after.
I really am stuck at this point, as everything I find with instructions on how to "unbrick" does require that the machine recognize that your kindlefire is attached. Running any of the tools I find requires that basic bottom dollar, which I don't seem to have.
That said, the behavior of "nothing at all: blank screen" when unplugged, and the behavior of "blinking firefirefire logo" when plugged in would tend to indicate that at the very least the device knows it's plugged in and getting juice, and some process is happening when that's true.
Can someone help? Is my next step to purchase a factory cable, or do I have a software solution available to me that I just didn't find in this haystack of solutions?
nothing doing when unplugged seems like a dead battery
would try to charge it with the wall charger for some hours regardless if the orange light comes up - this can last a while
furthermore i don't know which version of kfu for mac you'r using but zergrush is'nt working any more since stock rom 0.6.1
http://forum.xda-developers.com/showpost.php?p=21369040&postcount=653
for rooting use kindlewater:
http://forum.xda-developers.com/showthread.php?t=1443071
as far as i know the commands need to be entered with a ./ in front ie: ./install_drivers.sh
sisterdelirious said:
Can someone help? Is my next step to purchase a factory cable, or do I have a software solution available to me that I just didn't find in this haystack of solutions?
Click to expand...
Click to collapse
Thanks for reading my guide. I hope it helped you a bit.
Mac OS X is also my primary OS and I take my hat off to you for even trying things this way. I took the easy way out from the very beginning and just used Parallels Desktop to build Windows and Linux virtual machines. If things ultimately don't work out, you might want to try going that route as well. I believe Parallels offers a demo version if you want to see it in action. Regardless, I don't think that matters quite yet, because I tend to agree with b63 here. I think the biggest problem you have right now is a dead battery.
I've never had a dead battery, so I can't comment directly, but take a look at this thread, starting at post #226...
http://forum.xda-developers.com/showthread.php?t=1392693&page=23
There some back and forth for a couple of pages, but that user describes symptoms that sound very much like what you are seeing right now. I think you should try the wall charger first. Plug it in, force the Kindle Fire to turn off and just try to let it charge overnight or something. If you cannot get your KF charged with the stock wall charger, you might want to buy a factory cable. From what I gather, that user reported that his Kindle Fire booted into fastboot mode by using the factory cable even with a (nearly) dead battery. He was then able to flash the stock software, which is able to handle the dead battery situation better than some alternative ROM and have it go through the charge cycle.
Wow... so simple...
b63 said:
nothing doing when unplugged seems like a dead battery
would try to charge it with the wall charger for some hours regardless if the orange light comes up - this can last a while
Click to expand...
Click to collapse
This was the deal. When plugged in with the usb cord it didn't seem to be giving it power and being powerless could not be recognized by the computer. Plugged it into the wall charger and Voila! was able to start up just fine, still rooted via the kindlewater method, capable of being booted normally or booted into CWM recovery. Awesome!
I also did a quick double-check, and now that it's powered-up, running a terminal and typing "adb devices" actually returns a list with the kindle (serial number?) on it.
furthermore i don't know which version of kfu for mac you'r using but zergrush is'nt working any more since stock rom 0.6.1
http://forum.xda-developers.com/showpost.php?p=21369040&postcount=653
Click to expand...
Click to collapse
I read through everything and the version of kfu that was modded for mac was 0.9.2 which I mentioned in my original post. Sounds like since I was on 6.2.2 that mac version is definitely not going to help me (both kfu out of date and stock version out of date on zergrush) if I were to want it for rooting purposes.
for rooting use kindlewater:
http://forum.xda-developers.com/showthread.php?t=1443071
Click to expand...
Click to collapse
that is the one i used. I was looking for a mac tool for post-root rescue methods...i had thought that the kfu mac version had valuable rescue/unbrick capabilities but at this point I don't remember.
as far as i know the commands need to be entered with a ./ in front ie: ./install_drivers.sh
Click to expand...
Click to collapse
[/QUOTE]
Thankfully, I don't need to try that. my kf got properly unbricked just by plugging it into the wall charger.
Great guide, it was the battery
kinfauns said:
Thanks for reading my guide. I hope it helped you a bit.
Mac OS X is also my primary OS and I take my hat off to you for even trying things this way. I took the easy way out from the very beginning and just used Parallels Desktop to build Windows and Linux virtual machines. If things ultimately don't work out, you might want to try going that route as well. I believe Parallels offers a demo version if you want to see it in action. Regardless, I don't think that matters quite yet, because I tend to agree with b63 here. I think the biggest problem you have right now is a dead battery.
Click to expand...
Click to collapse
Thank you for your guide. I thought it was extremely well written and very helpful. It definitely helped me relax a little stress-wise while looking for a solution.
That was it (dead battery). I did try meddling around a bit with virtualbox virtual machines: a windows 7 ultimate, and a linux box that I have that does not have internet access making doing anything realtime while reading suggestions just isnt easy/feasible right now. I found that the virtualbox vms did not have access to the usb devices (flash drives, external hard drives, ostensibly if it were visible to the computer the kindle) despite my installing some optional extension packs for that purpose. I didn't explore the vms further to linux or xp simply because of the time required to install and configure a vm. I also didn't rewire my home so net access went to the linux box for the same reason... ultimately both are possible but both more hassle than it seems to be worth before simply asking the question, can it be done on a mac?
I've never had a dead battery, so I can't comment directly, but take a look at this thread, starting at post #226...
http://forum.xda-developers.com/showthread.php?t=1392693&page=23
There some back and forth for a couple of pages, but that user describes symptoms that sound very much like what you are seeing right now. I think you should try the wall charger first. Plug it in, force the Kindle Fire to turn off and just try to let it charge overnight or something. If you cannot get your KF charged with the stock wall charger, you might want to buy a factory cable. From what I gather, that user reported that his Kindle Fire booted into fastboot mode by using the factory cable even with a (nearly) dead battery. He was then able to flash the stock software, which is able to handle the dead battery situation better than some alternative ROM and have it go through the charge cycle.
Click to expand...
Click to collapse
I'm just so glad this worked. Thank you for your help!
glad to help ...
please mark the subject of the topic (edit first post) with [Solved]
Similar issue
My KF is seeming to have a similar but distinctly different issue as the OP. Because I can turn on the KF without it being plugged in, I cannot imagine that it is a battery issue.
When I plug it in to a Windows machine, the FFF bootloader comes on, the KF seems to connect, be recognized, fail at driver installation (which I have done manually, with no success), and then disconnect. This prevents me from running any sort of commands.
When I connect to my Mac, I get the FFF bootloader and then no response whatsoever.
Trying to run commands from Terminal or the Command line or using KFU on my Windows machine all result in a "waiting for device" message.
Not sure what I should do from this point to get it back to accepting adb commands. I'm confident that once I do I'll be able to save it, but at this point I'm stuck.
Any ideas?
Hi,
My rooted KF started behaving, weirdly so I decided to start from scratch and unroot it using the ClockworkMod recovery utility interface that was automatically loaded when I rooted it using Breakdroid. It started life with 6.2.2 but then updated itself to 6.3, so I downloaded the following file to do the unroot, and converted it into a .zip file called update.zip.
//kindle-fire-updates.s3.amazon...1E_4019920.bin
and went into the ClockworkMod recovery utility mounted my KF, did a factory reset, then applies sdcard update.zip which appeared to perform sucessfully, however when I rebooted, it launched the Stock KF screen, no fire fire fire, and has since stayed there. Can anyone please help! Many thanks.
Does KFU recognize it? If it does you are good to go.
Hi,
Nope. I'm using a Mac, so I use Breakdroid, and it's not picking it up.
http://forum.xda-developers.com/showthread.php?t=1644970
soupmagnet said:
http://forum.xda-developers.com/showthread.php?t=1644970
Click to expand...
Click to collapse
Keep up the good work soupmagnet!
Thanks soupmagnet,
I know it's the same question asked over and over again, I'll give it a shot and let you know if I sort it out. Appreciate your time.
All things point to a factory usb cable which I have ordered. Now I have to read books the old way...analogue!
nickvon said:
All things point to a factory usb cable which I have ordered. Now I have to read books the old way...analogue!
Click to expand...
Click to collapse
Actually a factory cable, while nice to have, doesn't seem necessary in your case. (Hint Read about the different bootmodes.
Hi again Soupmagnet,
So I eventually got hold of my factory cable which I ordered off Ebay from Hong Kong, so I plugged it in and hey presto, nothing happened. I'm still stuck on the Kindle Fire screen. I've been using a Mac and Breakdroid doesn't pick it up at all. I decided to see if a PC could pick it up using KFU, and it's still offline, although in My Computer I do see an external drive and device manager does call it Kindle. I have a feeling I am the 1% of bricked Kindle Fire users that have well and truly properly bricked their Kindle. Could it perhaps be the cable not in fact being a factory cable at all? I'm getting pretty desperate with this situation. Can you offer me advise.
Nickvon
Oh and further to my last I was changing boot modes but as it couldn't recognize the device, it was pointless.
nickvon said:
I have a feeling I am the 1% of bricked Kindle Fire users that have well and truly properly bricked their Kindle.
Click to expand...
Click to collapse
Take a breath, relax, and rest assured that you are more likely in the upper 90% range.
As I said before, the factory cable, while nice to have isn't usually required to fix most devices. All it does, is puts the device in fastboot mode and provides direct power to the device via usb in case of low or now power
Your problem is simply a matter of fixing your drivers so you can communicate with the device and change the bootmode.
[Edit:] It's been a while since this post was first started so I forgot you were using Mac instead of Windows.
Open your Terminal and enter the following:
Code:
cat ~/.android/adb_usb.ini
Your output should read:
Code:
# ANDROID 3RD PARTY USB VENDOR ID LIST -- DO NOT EDIT.
# USE 'android update adb' TO GENERATE.
# 1 USB VENDOR ID PER LINE.
0x1949
Anything other than would explain why you aren't able to change the bootmode normally.
Are you using Terminal commands to change the bootmode or are you using Breakdroid?
Hello everyone,
I've tried to find my specific situation in related threads, but haven't seen my exact issue, so here goes. Several threads seemed to talk about what I'm seeing, but the remedies that worked for them have not worked for me.
I have a Kindle Fire running 6.3.1, and I tried rooting yesterday with Kindle Fire Utilities 0.9.6 on a Windows Vista Virtual Machine.
The drivers appeared to install correctly, because KFU was able to see the Kindle and showed "online" when I started the process. The Device Manager seemed to have the correct information as well.
In KFU, I selected option 2 from the main menu, to "Install Permanent Root with Superuser". KFU started downloading twrp.img, but was unhappy with the MD5 checksum, so it issued the error: "Oops... something went wrong with the download. The recovery downloaded is not correct. Please try the download again"
At this point, the run.bat program exited, and the Kindle rebooted.
However, it appears that KFU at least partially succeeded in putting the Kindle into fastboot mode, because now I just get the "Kindle Fire" orange and white logo and nothing else happens. Also, I can no longer access the Kindle from my computer.
Now, when I run KFU again, it can't find the Kindle. I also can't contact it by running adb or fastboot manually, either from Window or from Ubuntu.
I've tried most, if not all, of the tricks I've seen in related threads to get back into contact with the Kindle and restore it to normal boot mode. The fastboot executable gets stuck in the < waiting for device > state, and I've tried power-cycling the Kindle, unplugging and plugging it back in, timing the execution of fastboot with the startup screen, etc. Since KFU did not successfully install Fire Fire Fire or TWRP before the failure occurred, I can't use either of these to recover.
I have ordered a Factory Cable from SkOrPn, but I'm curious if there's anything else I can try before it arrives, or if maybe I've missed something in all of the reading I've done over the past couple of weeks. (I read many threads and posts about rooting the Kindle, along with the Beginners Guide, before I worked up the courage to actually try it yesterday, and since then I've been educating myself on recovery techniques).
Sorry for the lengthy post, thanks for any help or clues, and I apologize if this has been answered already in another thread.
You might try powering it down completely, run KFU, choose option 1, then choose normal boot mode (4000) and when it comes up with <waiting for device> then hit the power button on your Fire.
This has worked for me in getting it back to normal boot when things seemed to be hung up. I sometimes had to hold the power button down to hard shutdown after this, but when rebooted after that, it booted normally.
Can't hurt to try it in this case.
You say you're using a VM, but what OS are you typically running? Mac OSX and Linux both handle device drivers by far better than their MS counterparts.
soupmagnet said:
You say you're using a VM, but what OS are you typically running? Mac OSX and Linux both handle device drivers by far better than their MS counterparts.
Click to expand...
Click to collapse
spfldcynic said:
You might try powering it down completely, run KFU, choose option 1, then choose normal boot mode (4000) and when it comes up with <waiting for device> then hit the power button on your Fire.
This has worked for me in getting it back to normal boot when things seemed to be hung up. I sometimes had to hold the power button down to hard shutdown after this, but when rebooted after that, it booted normally.
Can't hurt to try it in this case.
Click to expand...
Click to collapse
spfldcynic - Thanks for the tip. I tried it, but never got past the < waiting for device > state. It makes me wonder if the Kindle is really in fastboot, or if it's in some other state that makes it unresponsive to external commands. Hopefully the Factory Cable will fix this.
soupmagnet - My host OS is Ubuntu 10.04. I'd like to be able to work with the Kindle directly in Linux, but went the Window route initially because I'd heard good things about KFU. After reading your post, I found the FireKit tools for Linux, but got the same results using the "normal_boot" script that I had with KFU and with directly issuing the "fastboot -i 0x1949 oem idme bootmode normal" command from both Linux and Windows.
calgator said:
spfldcynic - Thanks for the tip. I tried it, but never got past the < waiting for device > state. It makes me wonder if the Kindle is really in fastboot, or if it's in some other state that makes it unresponsive to external commands. Hopefully the Factory Cable will fix this.
soupmagnet - My host OS is Ubuntu 10.04. I'd like to be able to work with the Kindle directly in Linux, but went the Window route initially because I'd heard good things about KFU. After reading your post, I found the FireKit tools for Linux, but got the same results using the "normal_boot" script that I had with KFU and with directly issuing the "fastboot -i 0x1949 oem idme bootmode normal" command from both Linux and Windows.
Click to expand...
Click to collapse
Did you try the whole process from scratch on Ubuntu? Also, plug it into the wall charger and make sure it has some juice before continuing (if you haven't already)
Running low on ideas man, hope someone else can do more for you.
You can't just get up and go with Linux, there is some configuration that needs to be done first. Have you set up your udev rules and installed 32-bit libs?
[SOLVED] KFU Failed, Now Kindle Fire Won't Boot
soupmagnet said:
You can't just get up and go with Linux, there is some configuration that needs to be done first. Have you set up your udev rules and installed 32-bit libs?
Click to expand...
Click to collapse
Yes, after reading your post I've discovered that you are correct. I followed Sblood86's instructions on setting up the udev rules (http://forum.xda-developers.com/showthread.php?p=22067293), and I already had the 32-bit libraries and tools since I have the android sdk and a 32-bit Ubuntu installation.
Armed with this correct configuration, I typed
Code:
"./fastboot -i 0x1949 oem idme bootmode 4000"
And this time, saw the following:
Code:
< waiting for device >
...
OKAY [ 0.201s]
finished. total time: 0.201s
Meaning that all is now well with my Kindle Fire, until the next rooting attempt.
Thanks for your help!
So, although the original KFU problem is not completely understood by me, since my Kindle is working, I'll say the problem is solved.