I was trying to root my phone using unrevoked 3.32 and during the install it, it stop with a back up CID error missing or something like that. i checked to see in hboot if it was rooted with it showing s-off, and it was but recovery still showed the regular triangle red error. So i restarted normally and tried into install terminal emulator on the phone and thats when it first started vibrating 5 times, then go blank with a green led flash. the phone will boot normally usually be able to use it for a min or less then it will repeat with the blank screens. After checking back into hboot it now shows that its unrooted with s-on. Now i also have problems with the usb/sdcard.
Things i have done to get it back to normal:
- hard reset using clear storage.
-Checking in the SD storage menu i could see it wasn't reading the SDCard so i restarted it in bootload and thru fastboot typed: fastboot oem enableqxdm 0.
- flash through bootloader this file : 3.70.651.1_PC36IMG.zip
After flashing it still takes multiple battery resets to finally get it through the first start up menu and then to the regular home screen. Seems to read the SDcard fine but when connecting the usb from wall charger or PC it doesn't recongnize at all.
The phone is 4 days old and seems to be back to stock except it still vibrates and goes blank with green led flash and it wont recognize charging/pc connection. Will i have any problem if i just go back to sprint and say i want a new one its not working right?
Phone info:
Baseband: 2.15.00.11.19
kernel: 2.6.32.17-gee557fd
Software: 3.20.651.1
PRI: 1.90_003
PRL: 60676
Hardware: 0003
HBOOT-2.10.0001
strdrk1 said:
I was trying to root my phone using unrevoked 3.32 and during the install it, it stop with a back up CID error missing or something like that. i checked to see in hboot if it was rooted with it showing s-off, and it was but recovery still showed the regular triangle red error. So i restarted normally and tried into install terminal emulator on the phone and thats when it first started vibrating 5 times, then go blank with a green led flash. the phone will boot normally usually be able to use it for a min or less then it will repeat with the blank screens. After checking back into hboot it now shows that its unrooted with s-on. Now i also have problems with the usb/sdcard.
Things i have done to get it back to normal:
- hard reset using clear storage.
-Checking in the SD storage menu i could see it wasn't reading the SDCard so i restarted it in bootload and thru fastboot typed: fastboot oem enableqxdm 0.
- flash through bootloader this file : 3.70.651.1_PC36IMG.zip
After flashing it still takes multiple battery resets to finally get it through the first start up menu and then to the regular home screen. Seems to read the SDcard fine but when connecting the usb from wall charger or PC it doesn't recongnize at all.
The phone is 4 days old and seems to be back to stock except it still vibrates and goes blank with green led flash and it wont recognize charging/pc connection. Will i have any problem if i just go back to sprint and say i want a new one its not working right?
Phone info:
Baseband: 2.15.00.11.19
kernel: 2.6.32.17-gee557fd
Software: 3.20.651.1
PRI: 1.90_003
PRL: 60676
Hardware: 0003
HBOOT-2.10.0001
Click to expand...
Click to collapse
That's weird. I'm pretty sure the vibrate 5 times and green blinking led indicates that the phone is in diagnostic mode. I'm not sure how to remedy the situation, I would've suggested a PC36IMG back to stock, but you already tried that. I would try taking the battery out for an hour or more (i've read of people being stuck in diagnostic mode, and leaving the battery out for a good length of time fixed it, i think) then try booting up, and seeing if it works. If not, to answer your question, as long as the bootloader shows S-on, you will have no problems taking it back to Sprint. You need to make sure you have no 'evidence of rooting' on your sd card, just to make sure that the sprint tech doesn't see anything on there. Good luck.
I formatted the sdcard, but it seems to be creating these files QXDM_some numbers.dm is this normal or any indication of rooting the phone.
Sorry to be the bearer of bad news but I had the same issue and eventually gave up after 3 solid days of working on it. You name it, I tried it. Had to get it replaced.
Something about unrevoked and my old 002 phone didn't jive together and the root aborted at an unrecoverable stage. No sd card mount, no adb, not even able to connect via usb, so running an ruu or new pc3600img wasn't an option.
As for the 5 buzzes and shut down after a min or so... Your guess is as good as mine. You can put it in diagnistic mode with the arrow up/power button boot, but thats 3 buzzes not 5.
Wish I could offer some actual help :/ Let us know if you find a fix.
Oh, before I took it back in I did a hard reset so it would reboot before they could get past the setup menus and see the superuser permissions app. Not that they'd care, but just in case.
I have just returned my EVO to sprint for this same problem. He told me it was a common problem. I get my new on today. They could have cared less that it was rooted, he told me it did not matter.
derekstory said:
I have just returned my EVO to sprint for this same problem. He told me it was a common problem. I get my new on today. They could have cared less that it was rooted, he told me it did not matter.
Click to expand...
Click to collapse
I ended up exchanging mine also. The lady really could have cared less. i wish i would of known cause i spent some time trying to get it back to normal. My sister also ended up exchanging hers because she got the white one and wanted the black one instead.
thanks for any help and replies.
I too had the same problem. It all happened when I was trying to flash cyanogen 7 RC2, I wiped all data, and all seemed fine. I rebooted and it went right to the bootloader and I noticed I was S-ON. Tried to re-root, and run a RUU. I did actually get it to boot to sense, but it froze and then I got the buzzes, and the green lights. I went to sprint since I have insurance. They checked it out and then an hour later, they gave me another one.
My EVO is currently stuck in the same state. I have spent a huge amount of time working on it, and have some information. I'm just dumping as much as I can remember in to this post, so excuse the lack of organization.
Before I go any further - I have not been able to fix the issue!
My phone was about as stock as possible when I took it to the Sprint store. They ordered me a new one and gave the broken one back. I have taken a few more risks now that my new one is on the way.
The initial problem started after flashing MIUI recently. The phone booted normally, but I noticed that the SD card was inaccessible. I would bet that the phone was refusing to charge over USB at this point as well, as that issue goes hand-in-hand with the sdcard problem.
The sdcard and its contents were fine. I later made a backup of the card and lost nothing.
Symptoms, high level info:
Phone immediately vibrates 5 times and begins flashing a green indicator, screen black at power on
Under unknown circumstances, the phone will display the white EVO boot screen before exhibiting the above behavior
Cannot exit this mode unless phone is unplugged and battery is removed
Bootloader can be accessed by holding volume down and power when starting fresh
SD Card is accessible in bootloader - indicates the problem is not purely hardware related
Fastboot can be used to temporarily (1 boot) gain access to sd card
Phone can be flashed with official PC36IMG
Phone can be set into RUU mode and flashed with official RUU
Official update.zip can be flashed from stock recovery
Qualcomm diagnostic tools can be used
Phone will remain in the installed OS for a very short amount of time
Bootloader shows S-ON, 'fastboot oem boot' shows Super CID and CID=111111111 instead of SPCS_001
Because one of my initial ideas was to flash a stock PC36IMG from the bootloader, I lost access to a custom recovery very early in the process. Other users may have better luck if they do not immediately flash a stock recovery.
Flashing PC36IMG is accomplished as usual. Vol- + Power.
To temporarily enable the sd card, disable Qualcomm Download mode:
Boot into bootloader
Wait for it to scan the SD Card
Select Fastboot (Power to select)
Plug into computer
Open a command prompt and ensure you have the fastboot executable
Command: fastboot oem enableqxdm 0
Exit fastboot
Select Clear Storage and select No to reboot OR
Select Recovery
The phone will boot into the OS. Under unknown circumstances, the phone will reboot. The amount of time can vary quite a bit. Enabling Airplane mode does not help. Using diagnostic tools to put the phone in Offline mode does not help.
If you would like to use Qualcomm diagnostic tools, the phone will have to be in diagnostic mode, rather than Download mode. The above steps will get you most of the way there, with the added annoyance that the phone will not enter proper diagnostic mode if left plugged in the entire time.
To ensure diagnostic mode correctly enables (or rather, that download mode disables):
Perform the fastboot command to disable qxdm
Unplug the phone
Navigate back to the bootloader, select Clear Storage
Select No (Vol-) to reboot
The white EVO boot screen will display
The screen will go black before the Sprint/4G animation plays
Plug the phone as soon as the white screen disappears, before the Sprint/4G animation
The phone will display in QPST Configuration without saying *Download* everywhere. The phone number will be incorrect, but that value is actually stored as a Directory ID in the NAM. In other words, it's okay.
The QPST Service Programming tool looked like a good place to start. If you would like to look at the configuration options for the EVO, you can start an offline connection using the profile "FFA/SURF QSD8650 Rev 2.0".
Note that the phone will always reboot after writing any values to the phone. This means you will have to pull the battery, unplug it, boot into fastboot, disable qxdm, boot into the OS each time.
You will need your MSL code for many of these applications. You can get it by calling Sprint and asking. They will not provide the code through email.
I can confirm that at least some changes in the Service Programming app will stick. I changed the banner, under the Display tab, to "Brick" (from Sprint), and it showed up in the Notification dropdown.
The NV util can read the values from the phone correctly.
QXDM can issue command to the phone.
ADB will not work. This limits the ability of tools like unrEVOked to do whatever they do. Getting ADB to work could be useful. Note that I did re-enable Debugging in the Setting->Applications menu to no avail. I believe this is a general side effect of this problem and perhaps a key symptom.
The bottom line is that I have run out of ideas. I have not found a setting in any of the QPST or QXDM tools that indicate this mode can be turned off. I have a hard time believing that there is some permanent switch in the Qualcomm SOC that says "always boot into this mode forever", but who knows.
Any suggestions would be great.
To summarize, I have installed a stock PC36IMG, update.zip, RUU. I have access to almost any setting in the phone, but cannot write to NV because it's in the S-ON state, which limits certain fastboot wipe options and the ability to push new images to system partitions from fastboot. I can, in theory, use the QPST Download software to move images if I can find one that might work.
When is the last time you tried running a 3.70 PC36IMG RUU?
I ran the 3.70 RUU literally minutes ago.
RUU_SuperSonic_S_Sprint_WWE_3.70.651.1_Radio_2.15.00.11.19_NV_1.90_release_161482_signed
Apparently still not taking?
That's the thing - it *is* taking. Whatever is triggering this mode is not being reset by the RUU (or any other full clear/flash technique).
I have a dump of the NV memory, but I want to run through it with a hex editor to make sure it doesn't have anything that would identify my Sprint account or identity before posting it.
SLOSifl said:
That's the thing - it *is* taking. Whatever is triggering this mode is not being reset by the RUU (or any other full clear/flash technique).
I have a dump of the NV memory, but I want to run through it with a hex editor to make sure it doesn't have anything that would identify my Sprint account or identity before posting it.
Click to expand...
Click to collapse
Ah I see, and good precaution.
My ESN is in the qcn file, and I assume my MEID is as well. I will try to zero them out if I can find them all.
If my phone's ESN is 12345678, then it is in the qcn file as 78 56 34 12.
Does anyone else happen to have a known good QCN? Maybe I can compare them side by side to locate the differences. I suspect that there will be a lot of them, but I can eliminate most of them pretty easily.
While I work on the file (and debate whether or not it's safe to post), here is some information from the NV dump:
Code:
File Version: Major 2, Minor 0, Revision 0
File Summary:
Phone Model: 16 [FFA/SURF QSD8650 Rev 2.0], Configuration Name: default, Total NV Item Count: 1650
Phone Model 16 [FFA/SURF QSD8650 Rev 2.0] Configurations:
Configuration Name: default
Mobile Properties:
ESN: 0xMASKED
Phone Model: 16 [FFA/SURF QSD8650 Rev 2.0]
NV Major: 0
NV Minor: 0
SW Version: 8650B-SDCAPLYM-324026
Client Name: QPST Software Download 2.7.0.362
Code:
Feature Mask:
...Removed for brevity....
Total Set Bits: 108 of 432
Without bothering to specify all the set bits (although there are some interesting ones like "Bit 306: F_UI_GOOFY_MENU_BIT"), maybe someone can confirm that 108 or 432 is close to correct.
I loaded up a nv.img from a nandroid backup I took the day this problem happened (before flashing a ROM). I suspected that the nv.img and the qcn I just pulled should both represent the same general memory in the phone.
The image is...definitely an image. Exactly 640kb, tons of empty space and apparent padding. Much different in overall layout than the QCN, and no trace of my ESN. However, I was able to locate the GPS URLs in both files. While not even close to the same offset in the file, that small section of similarity indicates that the same memory was probably accessed.
Unfortunately I know of no way to push the nv.img to the phone in its current state. If I were able to get the nandroid backup's nv.img onto the phone I could at least eliminate the entire NV memory as a variable. If it fixes it, then awesome, and if it doesn't, then I can ignore the file entirely.
Here is the QCN file with my ESN removed. There may be other private information in the file, but at this point, Sprint is ordering me a new phone, and gave me this one back, so I don't know if they can really do anything about this.
http://rapidshare.com/files/455015717/public.qcn
My enthusiasm toward poking around this file is dropping off pretty quickly since I no longer believe this is where the problem lies.
I had the same thing happen to my EVO last week. Pretty much the exact same symptoms as you. I was able to get the RUU to run, and return my phone back to stock thinking this would fix the problem. I can boot into Sense, but the phone will shut off and do the 5 vibrate thing within a couple of minutes.
I took it into the Sprint store, and the rep told me there is nothing they would do and they would not replace my phone. He assumed it had been rooted (which it had, but I returned it 100% to stock before taking it in), but I have also read of this same thing happening on unrooted phones. I plan on calling Sprint and/or HTC directly to try and get the phone replaced.
From what I've read, it kind of sounds like this is a hardware failure. Possibly something in the internal memory or RAM. Of course, this is just mostly a guess I have. It seems this happens to unrooted phones, but is more common on rooted phones, possibly because of all the flashing we do.
Like I said, it's just a guess of mine, but it kind of makes sense. I wish I could be more help, and I'll definitely be following this thread because this seems to be a fairly common problem with EVOs and Incredibles that nobody has seemed to figure out yet.
hello,
the problem is heat.try to use your evo on the AC vent in your car with ac on you will not get reboot or eny shut down than try to use with out ac...
whenever internal temp goes more than 38C the evo goes off 5 vib. and flashig..
i spent long time testing this so i almost 100% sure that heat is the problem with my evo...
i dont know if there is a way to change the seting on shut down due to heat but it mey be...
adasio said:
hello,
the problem is heat.try to use your evo on the AC vent in your car with ac on you will not get reboot or eny shut down than try to use with out ac...
whenever internal temp goes more than 38C the evo goes off 5 vib. and flashig..
i spent long time testing this so i almost 100% sure that heat is the problem with my evo...
i dont know if there is a way to change the seting on shut down due to heat but it mey be...
Click to expand...
Click to collapse
I was never able to fix mine, but before getting it exchanged i let it sit all night with the battery out and would have the same results. So i know mine wasn't overheating.
strdrk1 said:
I was trying to root my phone using unrevoked 3.32 and during the install it, it stop with a back up CID error missing or something like that. i checked to see in hboot if it was rooted with it showing s-off, and it was but recovery still showed the regular triangle red error. So i restarted normally and tried into install terminal emulator on the phone and thats when it first started vibrating 5 times, then go blank with a green led flash. the phone will boot normally usually be able to use it for a min or less then it will repeat with the blank screens. After checking back into hboot it now shows that its unrooted with s-on. Now i also have problems with the usb/sdcard.
Things i have done to get it back to normal:
- hard reset using clear storage.
-Checking in the SD storage menu i could see it wasn't reading the SDCard so i restarted it in bootload and thru fastboot typed: fastboot oem enableqxdm 0.
- flash through bootloader this file : 3.70.651.1_PC36IMG.zip
After flashing it still takes multiple battery resets to finally get it through the first start up menu and then to the regular home screen. Seems to read the SDcard fine but when connecting the usb from wall charger or PC it doesn't recongnize at all.
The phone is 4 days old and seems to be back to stock except it still vibrates and goes blank with green led flash and it wont recognize charging/pc connection. Will i have any problem if i just go back to sprint and say i want a new one its not working right?
Phone info:
Baseband: 2.15.00.11.19
kernel: 2.6.32.17-gee557fd
Software: 3.20.651.1
PRI: 1.90_003
PRL: 60676
Hardware: 0003
HBOOT-2.10.0001
Click to expand...
Click to collapse
It's bricked. Happened to me when I tried to fix a problem with my phone not mounting the microSD card to any computer (got error message back on a Windows computer saying that the device wasn't recognized). You could probably try to flash the PC36IMG.zip file again from the bootloader, this time without all the addenda at the beginning (if you did that already, the nevermind).
My guess: pray that Sprint doesn't see any evidence of root. If you RUUed back already, they may not see it. You're probably in better position than I am, since the brick happened before I could RUU back with a PC36IMG file (and thus Sprint could see the root. At least Asurion doesn't seem to care about root, as long as I say nothing about it).
Related
Hey guys,
I hope you're all well.
Great forum by the way.
I've searched extensively for solutions to my problem, yet I've been unable to find anything.
I think the problem started yesterday, when I restarted my phone and for some reason it went into safe mode.
I didn't lost any functionality so I didn't care too much until this morning, when I tried to get out of safe mode.
My phone has taken me to the bootloader (white screen with skateboarding Android) and for some reason, the power key (used to select options) and the volume keys (used to scroll) are not functioning.
As a result I cannot click or choose anything and the white bootloader screen persists in limbo.
I desperately need some suggestions, any help is very much appreciated.
Just so you know:
I've taken the battery out and put it back in, which takes me straight back to the bootloader screen, same with sim card.
The phone is running Coredroid (can't remember which version).
Has S-OFF.
Sorry I'm not much of an expert...
Also, on startup, phone says something along the lines of:
SD Checking...
LOADING... [PD98DIAG.zip]
NO IMAGE!
LOADING... [PD98DIAG.nbh]
NO IMAGE OR WRONG IMAGE!
LOADING... [PD98IMG.zip]
NO IMAGE!
LOADING... [PD98IMG.nbh]
NO IMAGE OR WRONG IMAGE!
Kind regards,
- Ric
Something has become corrupted.
Best bet would be to use an ruu 2.36.405.8 and lower, once loaded up, skip through the setup and then root again.
http://driphter.com/index.php?topic=3867.0
after you've done all that, install rom manager, and then restore your last backup.
Just a quick update.
Managed to get into Clockwork Mod Recovery.
Got the SD Card to mount.
Formatted it in windows.
Copied over Coredroid.
Went thru the install process.
Installed without error.
Booted up.
Took it's time, displayed the Coredroid animation but then vibrated and took me straight to Bootloader again.
Any advice or best to do this RUU thing?
Would this:
RUU_Ace_HTC_WWE_1.32.405.3_Radio_12.28b.60.140e_26.03.02.15_M3_release_155032_signed
Be ok?
Am I in the right ballpark?
Truly got no clue when it comes to this stuff
use the 2.36.405.8 RUU, then you wont have to spend your time updating the radio and such, that version of gingerbread is rootable using gingerbreak (so just follow that path of my method and you're set)
JSLEnterprises said:
Something has become corrupted.
Best bet would be to use an ruu 2.36.405.8 and lower, once loaded up, skip through the setup and then root again.
after you've done all that, install rom manager, and then restore your last backup.
Click to expand...
Click to collapse
Hello mate,
Just a quick question.
How do I get my computer to recognize my phone prior to running this RUU thing?
Considering I can't scroll or select anything in bootloader screen?
Can I run this RUU thing from ClockworkMod?
Kind regards,
- Ric
you run it from your pc. its an advaced installer that pushes the stock rom to the device and overwrites everything... it will put the phone into a different bootloader state than the one you can nav through.
Also, sometimes the phone is booting into bootloader, while other times it is booting into ClockworkMod.
It seems I have no control over which screen it initially boots to.
I DO HAVE options in ClockworkMod because my volume keys allow me to scoll and my power button allows selection, whereas in bootloader, the keys do not function.
Could you PLEASE provide some advice on how to boot into ClockworkMod rather than bootloader?
Kind regards,
- Ric
JSLEnterprises said:
you run it from your pc. its an advaced installer that pushes the stock rom to the device and overwrites everything... it will put the phone into a different bootloader state than the one you can nav through.
Click to expand...
Click to collapse
Yes I do realize I run the RUU from the PC.
I don't think I was very clear.
I was trying to ask you what state the phone needs to be in?
Do I have to mount the SD Card from ClockworkMod?
Or can I run the RUU while in Bootloader?
Does it matter?
Neither have worked.
I get a 170 error (USB Connection error).
The RUU cannot see my phone.
I was wondering if there's a way to fix this?
I have also now tried to install Leedroid and Gingervillian.
Both have installed perfectly but refuse to boot all the way.
Instead taking me back to Bootloader...
Ok, Leedroid somehow booted.
No network or anything though.
Very unstable...
if the phone is running leedroid now and you have the htc sync tools installed (but without sync running, just needs to be installed for the drivers)
leave it as it is connected to your pc, doesnt matter if debugging or anything else is on or off. just leave it alone sitting where it is on your desk or wherever it is...
Start the RUU, and then just follow the path the installer takes you through, then let it do its magic...
Ended up d/l Cyanogen.
Installed it.
Working, detected networks, wifi is connected.
All good I suppose.
That was a bit scary!
Thanks for your help mate.
So, figured I'd attempt to root the thing today via the AAHK on my locked DHD. According to the effen manual, I won't need to gold card it beforehand either.
I went through the process, and I was told that the ROM that I had installed (2.5.3? Sense 3.0) had to be downgraded, so I went ahead with it. After downgrading, I was brought to an unresponsive bootloader. Being patient enough, I let it sit while I watched a movie, yet nothing happened after. I took out the battery and restarted it, and all I got was the Hutchinson 3G (my carrier) logo and it just stops there.
When I try booting in recovery mode to get to the bootloader, it does so, but it hangs.
After enough tinkering, I noticed the bootloader was only responsive once I rebooted without the memory card inserted. The phone itself is still inaccessible as it just stops at the 3G logo.
So far, I've tried to restore it through an RUU, but since it's still (I assume) carrier locked, I have to find the ROM that shipped with it. Unfortunately, I can't find a ROM that caters to Hutchinson 3G ROI (Ireland), so right now I'm downloading a UK version of it to see if it works. Apart from that, any recommendations on what I could do next?
Thanks :3
people are gonna need a little more info eg. what does it say on the boot screen s-off etc
what rom your trying to flash, formatted sd-card or not, possibly a corrupted download
AAHK does the business well, but can baulk at the slightest thing.
fairly new to some of this myself, but learning, my DHD took 4 attempts to finally do now on JT R4
Oh, mmkay:
ACE PVT SHIP S-ON RL
HBOOT-0.85.0024
MICROP-0438
RADIO-26.09.04.11_M2
eMMC-boot
Apr 12 2011, 0:55:45
-----------------------------
Anything else I should include up there?
As for the ROM, I wasn't trying to flash anything bar the one that was downloaded through the AAHK client itself during the downgrade process.
After more tinkering, I've decided to leave it till today afternoon. Though I've made a few observations; so far
- The bootloader works fine when I turn it on WITHOUT the memory card
- The phone gets detected under the name "Android 1.0" when plugged in via USB both in hboot and fastboot. The fact that it gets detected I'll assume is a good thing
- Which leads to the second bit; it can be restored, since I've tried an Asian DHD ROM. It didn't complete because I was apparently supposed to find the appropriate ROM for it, which I assume is the H3G ROI version of it
- Aaand, the ROM still won't load up, and gets stuck at the H3G boot logo.
- According to the effen manual, it could be that my SD card was corrupt, so now my intention is just to merely restore it until I can actually afford to attain another memory card, which will be in a good few weeks and I don't wanna be smartphone-less for that period of time. But the only problem is; how?
if memory serves there isnt a rom in AAHK. the zip you intend using should copied be on your sdcard and initiated via recovery - vol down and on button. you should also be "s" off - did it offer to downgrade first [if needed]
from the manual
Insert the SDCard into the phone
Boot the phone
Turn on USB Debugging (Yes, plug it IN - use original cable plugged directly into the system board.)
IMPORTANT: Turn phone to charge-only mode. The phone stays in charge-only mode throughout this entire process. To make sure of this, check the default (menu > settings > connect to PC > charge only)
Win7/Vista: Right click on hack-ace.cmd and start as administrator (This will start the tool and bring you to the main menu)
option - 1
Install Clockworkmod
Clockworkmod version 5.0.2.7 -- yes
How to flash a custom ROM with ClockworkMod Recovery
Place the zipfile to be flashed on the sdcard. Do NOT unzip it.
Froyo disable Fast Boot: Menu > Settings > Applications > uncheck fast boot
Gingerbread disable Fast Boot: Menu > Settings > Power Options > uncheck fast boot
Turn phone off, no usb connected
Hold down vol- button, then press power to start, keep holding the vol- down button until Hboot menu shows up
Use the vol- down button to scroll down to recovery after some file checks are done (they will flash by quickly)
Press power to start recovery
Use vol down button to navigate, and the capacitive search button (bottom row of buttons, far right) to select
NOT VERY OPTIONAL/STRONGLY RECOMMENDED: If recommended by rom author or if flashing over another rom type (ex: cyanogenmod over anything else), wipe data/factory reset in Clockworkmod Recovery
Install zip from sdcard > choose zip from sdcard > select zipfile > Yes - (name of zipfile)
Repeat choose zip from sdcard for any add ons (gapps, themes, kernels, etc)
Press back button when flashing is complete until "reboot system now" is at the top of the screen.
Press power to reboot the system.
If desired, return the fast boot setting to ON in settings. (See above)
once yu crack it you'll see where you were going wrong
radio flashing is the easiest way to brick if you dont know exactly what your doing 99.9% of other stuff is recoverable
restoration is a more complicated path than rooting for noobs
I'm aware that there's no ROM included with the AAHK, I'm referring to the one that was downloaded THROUGH the AAHK when it said I'm gonna have to downgrade it beforehand.
And with reference to hboot, that's where another problem lies; my memory card is the one causing hboot to freeze. Hence, removing it prior to booting is the only way to get to it.
can you rerun AAHK and make a goldcard during setup and go that route -- wont help i know but being as its still "s"on you can return under warranty aslong as you dont send sim and sd-card tell them it wont go past h-boot.
if you have a card reader then format the card to make sure its clean, the drag and drop the required files on it - i have a lappy solely for this job with AV etc permanently turned off
Well, I'll rerun AAHK when I can find the SD card adapter, but since I've only recently moved house, it's gonna be near impossible until I get time off to unpack, which, till then, I'm still gonna need a functioning phone, so right now, I'm just looking for ways to return it to stock :3
i cant assist any further then as i've not yet RUU'd any devices as of yet.
hope you get it sorted
Thanks for trying anyways :3
I've been searching for an Irish RUU. Currently trying a UK version of it hoping it MIGHT just work. Anyone have more ideas?
Edit: Ok it didn't. Posted on the Three Ireland support boards trying to see if I can get an RUU
So I have upgraded my i927 captivate glide using the ROM from , but I only Androidupdate com called I927UCLH2_I927ATTLH2_I927UCLH2_Home tar md5 but I get a black screen with a slide down menu saying the date ‘Ongoing’ and an option to change the way that the device connects to another computer.
The update stated pass, it booted and proceeded to tell me that it was updating apps or something like that, then a black screen with the pull down menu from the top of the screen near the usb symbol came up but nothing else. I got a message a few hours later stating that the update application or something like that was not responding and an option to wait or quit. I chose wait, but nothing came of it eventually.
I then proceeded to try reflashing the process with no success even after factory reset and rebooting.
I then tried the pre-release ICS update as per XDA developers and other websites. Same thing
I tried a few other ODIN programs and ROMs but no success. Same issues including the hang up on the Samsung logo. I tried rooting it once and for some reason it started up into what looked like the same pull down menu, but it was requesting that I needed an to input a lock code for the network. I assume that is because my sim card was in it by now, but maybe not. I got so frustrated that I tried the bootloader and update bootloader options using the official ICS update ROM for some stupid reason but nothing. The thing is that at least it booted into the pull down menu that i got with a black screen again.
I then flashed with an updated ICS, CWM6 but cannot do the:
Third: Reboot into CWM6 (Volume- and power) install from sdcard (superuser)
Link to superuser: Superuser-3.2-RC2-arm-signed zip
Forth: Repeat third step above but install keyboard fix.
Link to keyboard fix: CWM_keyboard_backlight_fix zip
since I do not have an SD card that is working. I did get the SD Card in the device but I have always had problems with the format of it and I cannot put the zips onto the card due to the computer Win7 not recognizing it. I tried reformatting the device is HPUSB format program and windows. I inserted the card into the device to hopefully have it recognized on windows, and i gave me an option to format the SD card. So I proceeded and success. I was able to put the Zips onto the card. However, I returned to the CWM6 screen by pressing the VOL- and power keys but the files were no where to be found on the SD Card.
I moved on after a few other tries at it, so I tried to go backwards to the Gingerbread ROM. No success, same hanging issue at the Samsung logo.
I then tried to reflash with the devices original ROM as provided by DroidAngel on androidupdate com. Both without success.
I wanted to try the process involved on the 'stuck on boot screen' thread, but I cannot access the zip files on the sdcard in order to be able to do that.
I also bought my phone unlocked from the US (ATT version) and had it sent to me in Canada unlocked so I cannot just return it to the seller to get a new one, so my new phone is pretty useless.
I have spent two days reading through and trying different fixes and updated ROMs on multiple sites but I just cannot figure out what the heck to do now. I know that this site is not to spoon feed people and I am a noob to all of this but I am out of ideas and cannot find anything else to help out.
Where do I go from here. Is there a possibility of reformatting EVERYTHING on the device including all partitions etc etc.? I mean the hardware is fine, it is just a software issue. I do this to my laptop whenever I get into a bind.
Have you tried booting into CWM and restoring factory?
sent from my captivate glide running ICS (NardROM 0.3 Rooted)
Just a note, the SD card you're seeing in CWMR isn't actually your physical SD card, its the internal phone memory. I don't think we have a version of CWMR that reads the real external SD unless modified. So anything you put on it won't show up there. The folder structure will look like ... /sdcard/external_sd/ where /sdcard/ is where you want to put your files for CMWR to see, /external_sd/ is your physical card you can take in/out.
I have tried to reflash with CWM6 using ODIN v3. I didn't realize that the SD card that came up was actually a part of the internal memory. Thanks to you both for the help.
Any other suggestions since no matter what I do now the phone simply stops at the Samsung logo and wont turn off? I press the power button for the required time to shut it down but it automatically restarts by itself to again sit at the Samsung logo.
EaglesIII said:
I have tried to reflash with CWM6 using ODIN v3. I didn't realize that the SD card that came up was actually a part of the internal memory. Thanks to you both for the help.
Any other suggestions since no matter what I do now the phone simply stops at the Samsung logo and wont turn off? I press the power button for the required time to shut it down but it automatically restarts by itself to again sit at the Samsung logo.
Click to expand...
Click to collapse
A few questions about your situation right now:
Can you get into Download mode? (Turn off the device, in your case remove the battery. Press power en volume UP)
Can you get into CWM? (Turn off the device, in your case remove the battery. Press power en volume DOWN)
Does it keep asking you for the Network Key? Are you stuck at that particular point...?
Evil Alex said:
A few questions about your situation right now:
Can you get into Download mode? (Turn off the device, in your case remove the battery. Press power en volume UP)
Can you get into CWM? (Turn off the device, in your case remove the battery. Press power en volume DOWN)
Does it keep asking you for the Network Key? Are you stuck at that particular point...?
Click to expand...
Click to collapse
Okay, so right now I can still get into the download mode to flash, the CWM6 to factory reset and reboot which I have tried already as stated, and I have not been asked for the network key again since the one time quite a long time ago. The network key is only asked when I load one of the other custom ROMS though, but I have not tried any of those in a while.
I am stuck at the black screen with white Samsung logo.
In CWM6, do you see "mounts and storage" (Second to last option)
If so, connect your phone with the USB cable and select "mounts and storage".
In there and select "mount USB storage" (Again, second to last option, you'll have to scroll to get to it)
Now your PC should see the USB storage which is in fact what is marked as internal SD. So the sdcard CWM can actually see and install things from.
Now you can copy a custom ROM to it, and install it through CWM. Or install anything that is in CWM format.
You may get the Network Key Request as before. I do not know if it can be bypassed by starting it without the SIM. If so, you could then try to unlock your device using one of the methods on the forum.
Alternatively, and highly recommended by yours truly, is to buy the unlock code.
It is somewhat common for these devices to re-lock, so having the code handy is very convenient. I used americanunlocker to get mine, and I put the code on the inside of the back-cover should I find myself re-locked in the middle of nowhere. The code works, and isn't that expensive. In fact, it's a steal if you look at your own time invested in all this in terms of hourly wage! Of course, you'll need the IMEI code. You can find that by removing the back-cover and the battery.
Good luck!
Got it running on Bio360 but 'Not Registered on Network' now
Evil Alex said:
In CWM6, do you see "mounts and storage" (Second to last option)
If so, connect your phone with the USB cable and select "mounts and storage".
In there and select "mount USB storage" (Again, second to last option, you'll have to scroll to get to it)
Now your PC should see the USB storage which is in fact what is marked as internal SD. So the sdcard CWM can actually see and install things from.
Now you can copy a custom ROM to it, and install it through CWM. Or install anything that is in CWM format.
You may get the Network Key Request as before. I do not know if it can be bypassed by starting it without the SIM. If so, you could then try to unlock your device using one of the methods on the forum.
Alternatively, and highly recommended by yours truly, is to buy the unlock code.
It is somewhat common for these devices to re-lock, so having the code handy is very convenient. I used americanunlocker to get mine, and I put the code on the inside of the back-cover should I find myself re-locked in the middle of nowhere. The code works, and isn't that expensive. In fact, it's a steal if you look at your own time invested in all this in terms of hourly wage! Of course, you'll need the IMEI code. You can find that by removing the back-cover and the battery.
Good luck!
Click to expand...
Click to collapse
Thank you so much for the feedback, I actually had not thought about the unlock code idea, and since you put it into such perfect terms considering the time and effort that has to go into something like that, it is a good idea for sure to get one. The idea of keeping it on the inside of the back cover is another awesome idea. Kudos to you and thanks!
As for the rest of what you had stated about the mounting and what not; I actually mounted and successfully reflashed and installed all of the required files for the new ICS stock upgrade. The good news was that I got past the Samsung screen again and it said that it was updating all of the applications or whatever again, but then it just gave me the pull down menu again with very limited functionability.
I then used your suggestion to try out another ROM. I tried the Bio360 and followed all directions on the 'phone stuck on boot screen thread'. It worked! I finally have a functional phone again and will be able to get calls from my boss. Thanks!
Now that I know I have one option, I can explore any other options. I still cannot figure out how it is that I will be able to get the ICS upgrade but maybe I will try Kies.
However, I just found that I don't have network access anymore despite that I have a strong cell signal, so I presume that I will have to enter the unlock code somewhere. Where can I put that into? It didn't pop up to tell me anything.
EaglesIII said:
Thank you so much for the feedback, I actually had not thought about the unlock code idea, and since you put it into such perfect terms considering the time and effort that has to go into something like that, it is a good idea for sure to get one. The idea of keeping it on the inside of the back cover is another awesome idea. Kudos to you and thanks!
As for the rest of what you had stated about the mounting and what not; I actually mounted and successfully reflashed and installed all of the required files for the new ICS stock upgrade. The good news was that I got past the Samsung screen again and it said that it was updating all of the applications or whatever again, but then it just gave me the pull down menu again with very limited functionability.
I then used your suggestion to try out another ROM. I tried the Bio360 and followed all directions on the 'phone stuck on boot screen thread'. It worked! I finally have a functional phone again and will be able to get calls from my boss. Thanks!
Now that I know I have one option, I can explore any other options. I still cannot figure out how it is that I will be able to get the ICS upgrade but maybe I will try Kies.
However, I just found that I don't have network access anymore despite that I have a strong cell signal, so I presume that I will have to enter the unlock code somewhere. Where can I put that into? It didn't pop up to tell me anything.
Click to expand...
Click to collapse
You're very welcome! Glad to hear the phone is usable again. In order to get data back you will have to set your APN manually. Stock ROMs come with the APN settings for all providers it is expected to be sold with. But custom ROMs usually come without those settings. You can find the APN settings for your provider online, just do a search. There is even an app for it, but the name eludes me at the moment. You'll need wifi to get the app, though! Once the settings are in place (You put them in under wireless & Networks), you'll have data again.
As for the limited functionality, I had the same thing, at first. The upgrade was broken for me, I guess some settings/apps were causing problems. So, after flashing the upgrade, I did a factory reset in CWM. I also wiped the cache, and the Dalvik cache, for good measure(Under advanced in CWM). It rebooted, said it was upgrading and installing, and I let it sit for a few minutes. Then I was greeted by an initial setup screen, and the phone has been on a working ICS ever since! I did lose all my settings and such, but I had a back-up of those with Titanium Backup, and got those back that way.
Hope this will help as well.
HI,
I used to be more active in this forum, but honestly nowadays I can't found any reason to since everything has been smooth sailing for me without any problems—until this day, at least. Somehow I got my internal sdcard busted, it was pretty spontaneous, all I can recall is suddenly the system starts to reboot itself. Nothing much, I thought to myself, problem is the system keeps rebooting, it doesn't even last a minute. Naturally when faced with this problem one would do the usual procedure, namely completely format the thing to stock the rule out any possibility on the user side of things, but then this is the part when it starts to get interesting...
The thing refused to be formatted, seriously, it baffles me at first but it does
Things I've tried:
Fastboot, it hangs at writing system, whether I was doing it line per line manually or via the flash_all.sh script, I haven't tried the toolkit but I think it's safe to assume that It'll do the same thing. Even if it does go on (which it did, once) it doesn't do any sort of changes whatsoever to the system.
ADB, nope, not this one either. And since the system reboots faster before I can do anything worthwhile it's pretty much out of the question.
Recovery, multiple times I've tried nuking everything via CWM, nada. I've tried TWRP too, I have to boot it from fastboot since it apparently doesn't allow me to flash a new recovery either, it reverts back to CWM every time. Also tried to flash a different ROM (CM), that didn't work, it spits out an error message regarding some failure in changing metadata, thought it was a corrupted file or something, so I re-downloaded it, that doesn't work. Still convinced that it's corrupted I tried 4 different version of it without any luck. Even the one I had successfully flashed before. Interestingly enough, flashing the exact same ROM I'm currently using (ShinyROM) works, not that it seems to do anything.
Built-in data format from settings, now this doesn't work because I assume that it needs the stock recovery to work, which I couldn't flash because it wouldn't let me—in a sense that it flashes just fine on the command line—fastboot doesn't show up any error or anything—but it defaults back to CWM as soon as I reboot it.
Manually via terminal emulator/file manager, still nothing, curiously enough, Terminal Emulator indicates that the whole system is read-only (I tried making a file with it, it shows that exact message).
Grit my teeth, clench my fist and screams out every curse word that I know of, this somewhat reduced my stress levels, but ultimately yields nothing.
Which led to be believe that either my phone was either a) Haunted or b) Has a serious hardware problem, I'm leaning on the latter. A few quick lookup with my limited amount of Google-fu and I've found several threads that described the exact same issue:
http://forums.androidcentral.com/go...-factory-settings-no-matter-method-i-try.html
http://forums.androidcentral.com/go...eset-nexus-7-2102-using-multiple-methods.html
Both of which hints at it being a hardware problem. Which was my biggest fear since I can't really revert the phone back to stock now can I? Locking the bootloader doesn't seem to work either (the 'fastboot oem lock' command works just fine but just like every single thing I've tried, reverts back to my previous setup as soon as I did a reboot), plus this means I have to send it back with my private data still on it, and I can't say I trust Samsung, Google (or anyone really) with my private data. Not to mention some of the stories I've heard/read about Samsung and their policy regarding rooted devices (much less ones with an unlocked bootloader).
In case it helps, here's a few more details:
What state the device is currently in:
It boots up just fine, but nor for long, apps starts to hang and ends up with a cold reboot (sorry if it's not the right jargon, but it starts right from the Google screen).
Everything that doesn't require you to access the filesystem works fine.
Apps doesn't seem to be able to write anything to the filesystem, I tried backing it up with Titanium Backup, much to my surprise the backup files weren't made (although TiBu seems to indicate that they were).
What the device is running:
Variant: Maguro 16GB
ROM: ShinyROM 4.4.2
Kernel: franco.Kernel r395
Baseband: XXLJ1
Bootloader: PRIMED04
Also I don't know if this will affect things but for the record I'm running the latest Ubuntu and Debian.
So this post is pretty much a shot in the dark, since I think I know what I'm dealing with already; if anyone had this problem before in the past, or has it now and somehow managed to fixed it, please do tell. Or if anyone has any experiences RMA-ing your device with a condition like this I'd love to know.
Yep your EMMC is fried. Sorry man.. But you can go to warranty. They *should* accept it since it is a developers phone but they could make a lot of hassle about it being rooted..
Sent from my Galaxy Nexus using XDA Premium HD app
I have a bone stock 2013 Nexus 7 32 Gb Wifi, never had a problem with it. A few weeks ago, it notifies me of an update (Lollipop) so I apply it. Nothing but problems since then. It was very laggy and would glitch every few seconds while playing video (either local files or streamed over Plex, both had same issue). Sometimes when I'd wake it from sleep, the screen would look like an old CRT TV with static (except it wasn't moving, it was a fixed image). It would hang like this for seconds or sometimes minutes. Rebooting would usually resolve this for a while.
Tried a few 'lollipop tuning' tweaks, but when these failed to fix the video glitching and lagginess, I decided to revert to kitkat and followed an online tutorial (exactly like the one here except it had me install a standalone ADB/fastboot instead of full SDK) . No problem installing USB driver or setting nexus into USB mode. No problem getting it into fastboot mode and "fastboot devices" correctly listed the device, and "oem unlock" appeared to work fine as well. Running the flash-all batch file also seemed to go normally. But now my device is even worse than before:
- won't boot/run normally... no boot-up logo or video ever displays (or if it does, it's just a partial static image). Appears to get to a 'welcome' screen but the display is all messed (part of the screen is just repeated several times, so you can't see the entire screen). Unresponsive to touch, though it will make some sounds when you press in certain areas, but the display never changes. If I sleep it and wake it up, it shows the 'CRT static' mentioned above for many seconds before showing slowing showing the tiled/corrupted welcome screen. I can access the nexus' file system over USB on my PC even while it's in this borked state.
- display is now blank when getting into fastboot mode... i can time pushing the down-volume and power button so I know I am in fastboot mode ('fastboot devices' correctly lists the device) but the display is now completely black (not on, no backlight) in this mode.
I tried flashing to factory 4.4.4, 4.3, and 4.2 (always using 2013 wifi images) and it doesn't make a difference. Same results. Is there some bit of code that doesn't get reflashed during this reset that could explain why I'm having these issues? Any advice how to fix?
flyingsherpa said:
I have a bone stock 2013 Nexus 7 32 Gb Wifi, never had a problem with it. A few weeks ago, it notifies me of an update (Lollipop) so I apply it. Nothing but problems since then. It was very laggy and would glitch every few seconds while playing video (either local files or streamed over Plex, both had same issue). Sometimes when I'd wake it from sleep, the screen would look like an old CRT TV with static (except it wasn't moving, it was a fixed image). It would hang like this for seconds or sometimes minutes. Rebooting would usually resolve this for a while.
Tried a few 'lollipop tuning' tweaks, but when these failed to fix the video glitching and lagginess, I decided to revert to kitkat and followed an online tutorial (exactly like the one here except it had me install a standalone ADB/fastboot instead of full SDK) . No problem installing USB driver or setting nexus into USB mode. No problem getting it into fastboot mode and "fastboot devices" correctly listed the device, and "oem unlock" appeared to work fine as well. Running the flash-all batch file also seemed to go normally. But now my device is even worse than before:
- won't boot/run normally... no boot-up logo or video ever displays (or if it does, it's just a partial static image). Appears to get to a 'welcome' screen but the display is all messed (part of the screen is just repeated several times, so you can't see the entire screen). Unresponsive to touch, though it will make some sounds when you press in certain areas, but the display never changes. If I sleep it and wake it up, it shows the 'CRT static' mentioned above for many seconds before showing slowing showing the tiled/corrupted welcome screen. I can access the nexus' file system over USB on my PC even while it's in this borked state.
- display is now blank when getting into fastboot mode... i can time pushing the down-volume and power button so I know I am in fastboot mode ('fastboot devices' correctly lists the device) but the display is now completely black (not on, no backlight) in this mode.
I tried flashing to factory 4.4.4, 4.3, and 4.2 (always using 2013 wifi images) and it doesn't make a difference. Same results. Is there some bit of code that doesn't get reflashed during this reset that could explain why I'm having these issues? Any advice how to fix?
Click to expand...
Click to collapse
So your bootloader is blank right? I would flash a new bootloader asap! And see if that fixes anything
noahvt said:
So your bootloader is blank right? I would flash a new bootloader asap! And see if that fixes anything
Click to expand...
Click to collapse
I have to confess my ignorance here... I'm brand new to flashing android like this so I don't know the answer to your question. If part of tutorial I followed blanks out the bootloader (and doesn't write something in?)... then you're probably right. I shall look into this more tonight when I'm at home with the nexus. Thanks for at least giving me something to look into, that's exactly what I was hoping for!
This sounds more like a hardware issue than software to me. See if you can get a warranty repair or replacement.
From another thread by a user with a blank screen like yours:
Asus_USA said:
a7medmo7eb - We're very sorry to hear of this. Kindly email us at [email protected] with this copied problem description along with the serial number of your tablet and we will do our best to provide you with troubleshooting and servicing options.
If you have any further questions, comments or concerns please do not hesitate to let us know. We will be more than happy to assist you. Once again, thank you for choosing ASUS products and services.
Thank you.
-In Search of Incredible-
Technical Support Department
http://www.asus.com :: http://service.asus.com/
Click to expand...
Click to collapse
nhizzat said:
This sounds more like a hardware issue than software to me. See if you can get a warranty repair or replacement.
From another thread by a user with a blank screen like yours:
Click to expand...
Click to collapse
Thanks, you're probably right. I did read up to understand all this stuff a bit more, so I know it's not lack of a bootloader or anything. All img files install just fine, so my pc can talk to the nexus, just the screen is all wonky no matter what i do.
Unfortunately I bought this 1.5 years ago so I don't think it's under warranty anymore. Everything was fine until I updated to Lollipop! Seems a big coincidence that I had a hardware failure at the same time as that update... I feel like Google ruined my tablet...
There is a bug where sometimes when you unlock the bootloader it zeros out the data partition. This might be the cause of your problem. It happened to me when I unlocked mine and I got stuck in a bootloop where it kept booting into recovery then shutting off. I fixed the problem by using fastboot to format data. Also, the flashall script didnt work for me. I put all the .img files in the same folder as fastboot then used these commands.
fastboot format data
fastboot flash system system.img
fastboot flash boot boot.img
fastboot flash recovery recovery.img
after this I booted into recovery and did a factory reset for good measure and the problem was fixed. This may solve your problem. It may also be possible that you got a bad download. I hope this helps you
Masterchief87 said:
There is a bug where sometimes when you unlock the bootloader it zeros out the data partition. This might be the cause of your problem. It happened to me when I unlocked mine and I got stuck in a bootloop where it kept booting into recovery then shutting off. I fixed the problem by using fastboot to format data. Also, the flashall script didnt work for me. I put all the .img files in the same folder as fastboot then used these commands.
fastboot format data
fastboot flash system system.img
fastboot flash boot boot.img
fastboot flash recovery recovery.img
after this I booted into recovery and did a factory reset for good measure and the problem was fixed. This may solve your problem. It may also be possible that you got a bad download. I hope this helps you
Click to expand...
Click to collapse
Hmm, thanks for the idea, but fastboot wouldn't do "format data", giving me the error: Formatting is not supported for filesystem with type ' '
Googling that makes it not look good. Weird, thing is, it still technically boots up, just the screen is so wonky you can't see where you are or interact with it properly. Not sure what else to try (opening it up and re-seating touchscreen cables?).