Related
Edit: This guide is for EXPERIENCED users ONLY! For less experienced users please check UBERROOT easy full Root, S-OFF, SuperCID AND SIM UNLOCK for DZ/G2/DHD inc Voda .
Remember to always read and research before rooting! Discussion can be found starting on post #101 - #118 ~TheRomMistress
__________________________________________​
Please be aware that I am not responsible for any bricks etc. This is playing around with the phone internals, so be careful.
To get full write access to the Desire Z, we now have an Engineering HBOOT which was posted by MrPaveL (Thanks for that!).
To get your device to the engineering hboot stage [this is not full radio S-OFF, but 99% of people won't need radio S-OFF], please follow the guide below.
If you want full Radio S-OFF, SuperCID or want to remove the simlock on your phone, please follow this guide on instead. Once you have full Radio S-OFF you can use any Desire Z HBOOT and still have access to flash ROMs etc.
Credit goes out to scotty2, and all of the wonderful folks at #G2ROOT!
Donate to scotty2 (for root): [email protected] (PayPal)
This guide was derived from the guide for the G2, created by unrevoked512 on http://forum.xda-developers.com/showthread.php?t=833965. Also many thanks to vro25 for improvement suggestions.
You will need the following files:
VISIONary r14
wpthis-Z.ko MD5 c73c5e77c91d306c418983c002b60b93
hboot_7230_0.84.2000_100908.nb0 MD5 2ce1bdd5e4c1119ccfcecb938710d742
Step 1
Download and run VISIONary r14
Leave everything uncheck and click "temp root" now.
Once that's done click "Attempt Permroot Now!"
You now have permaroot.
Step 2
Push the files wpthis-Z.ko and hboot_7230_0.84.2000_100908.nb0 to /data/local/
Note: You might want to verify the MD5 sums, particularly for the hboot file, as if your download was corrupted, the file will brick your phone.
Step 3
Open a terminal on your phone, or open an adb shell from your computer.
Step 4
Code:
$ su
# insmod /data/local/wpthis-Z.ko
Note: make sure your screen is on before doing this as it will raise a root request on your phone (if you haven't previously granted it) - click ok on your phone to grant root.
It should return:
Code:
init_module 'wpthis-Z.ko' failed (Function not implemented)
That is good.
Step 5
FINAL WARNING: THIS STEP COULD SEVERELY DAMAGE YOUR PHONE. USING THE INCORRECT FILE COULD CAUSE IRREPARABLE DAMAGE, MAKING YOUR PHONE NOTHING MORE THAN A BRICK.
That noted, if you would like S-OFF, go ahead and run this command in your terminal.
Code:
# dd if=/data/local/hboot_7230_0.84.2000_100908.nb0 of=/dev/block/mmcblk0p18
Step 6
I think this is optional, but there are controversial opinions at the moment. In any case it will not hurt to run
Code:
# sync
to make absolutely sure everything will be saved.
Now reboot your phone gracefully and check that everything sticks.
Step 7 (optional)
This step is optional, if you want to install Clockwork Recovery.
Download ROM Manager from the market and install Clockwork, telling it that you have an HTC G2 when it asks. It will work without problems on the Desire Z.
Step 8 (optional)
This step is optional if you want to install an overclocked kernel. You might want to do a nandroid backup first, in case you want to go back later (just restore boot).
This overclocked kernel seems to crash the phone after Youtube videos are played in fullscreen. This issue is being investigated, but could take a while to resolve, since HTC hasn't released the actual DZ kernel source...
I have now recompiled the overclocked kernel for the Desire Z (all credit goes again to coolbho3000 for publishing the source!), to get the FM Radio to work as well. To get it to work please follow the guide on http://forum.xda-developers.com/showthread.php?t=834219, but instead of the zImage posted there (which breaks FM Radio on the Desire Z), get the one from http://www.opencodes.org/node/14 . You still need to use the bcm4329.ko file from the other thread. Also note that this will change your kernel version to 2.6.32.17 (instead of 2.6.32.21 stock). Please blame HTC for not releasing the newest kernel source. In any case I have not spotted any disadvantages...
So far I have not spotted any problems with this kernel, but if you do, let me know.
PS Bacon-bits by cyanogen do not fully work on the DZ. It won't boot with that ramdisk and the lights hack seems to fail as well. It is probably safest to wait for a full CM release, but this guide gets you 90% of bacon-bits.
stridger said:
Hi all,
I have just managed to get clockwork recovery work on the Desire Z. It's a bit hacky at the moment, and will probably get much easier in the due course. I am not going to post every little step that you can find out by googling, and please be aware that I am not responsible for any bricks etc. This is playing around with the phone internals, so be careful.
The reason it is this hacky is that we do not have an engineering bootloader for the Desire Z yet.
Download wpthis-Z.ko and wpthis-pre-OTA.ko from
http://content.modaco.net/dropzone/wpthis-Z.ko and
http://unforgiven512.udderweb.com/downloads/wpthis-pre-OTA.ko and put them in /data/local on the phone.
Download newest version of ROM Manager
Disable write protection via wpthis-Z.ko
Flash clockwork recovery from ROM Manager
Reboot into recovery
Make a nandroid backup !!!!!
Mount /data in Clockwork
Use wpthis-pre-OTA.ko in recovery to disable write protection.
You now have a fully working recovery. (note you will need to use wpthis-pre-OTA.ko step everytime you boot into recovery and want to write something from recovery [not needed for nandroid backups])
Click to expand...
Click to collapse
Your a genius dude Keep up the good work
We need quality devs like you to get this party started
JD
As soon as I did this step:
Disable write protection via wpthis-Z.ko
EDIT:
this is exactly what I did:
$ su
# insmod /data/local/wpthis-Z.ko
got this as result: failed (Function not implemented)
then all applications stopped working, ROM Manager crashed as soon as I select G2 from confirmation dialog when trying to flash Clockwork.
I then tried GMails and got loads of error popups, had to restart phone to get back to normal
EDIT: I do have Visionary installed set to Root on boot.
schriss said:
As soon as I did this step:
Disable write protection via wpthis-Z.ko
EDIT:
this is exactly what I did:
$ su
# insmod /data/local/wpthis-Z.ko
got this as result: failed (Function not implemented)
then all applications stopped working, ROM Manager crashed as soon as I select G2 from confirmation dialog when trying to flash Clockwork.
I then tried GMails and got loads of error popups, had to restart phone to get back to normal
EDIT: I do have Visionary installed set to Root on boot.
Click to expand...
Click to collapse
I urge you not to do anything in this direction, if you haven't even got permroot yet. Look at the G2 permroot forums, where all of these things are answered. The error is supposed to appear. Please be very careful if you don't want to end up with a brick.
I was afraid to do the G2 permanent root because it involved dd command and some G2 HBOOT file. There was one Desire Z user who ended up stuck in bootloader and have seen no other desire Z owners confirming this to work.
I guess I wait...
Sent from Desire Z
I flashed the desire z rom on my g2 yesterday after root, is my g2 now considered a desire z? if so it should be okay for me to follow these instructions right?
schriss said:
I was afraid to do the G2 permanent root because it involved dd command and some G2 HBOOT file. There was one Desire Z user who ended up stuck in bootloader and have seen no other desire Z owners confirming this to work.
Click to expand...
Click to collapse
You don't need the eng hboot to get permroot... You just need to temproot with write-protection disabled. But as you say, it's best to wait until the right tools come out.
stridger said:
You don't need the eng hboot to get permroot... You just need to temproot with write-protection disabled. But as you say, it's best to wait until the right tools come out.
Click to expand...
Click to collapse
Exactly, that's what the logic sugests.
I was hoping to:
Temp root with Visionary (already done)
Disable write protection via wpthis-Z.ko
then try "sync" command to write changes.
Then, after reboot, I should have perm root and nand on read-only.
But I got scared by the errors I got after I disabled write protection.
g1junky said:
I flashed the desire z rom on my g2 yesterday after root, is my g2 now considered a desire z? if so it should be okay for me to follow these instructions right?
Click to expand...
Click to collapse
amazing,
thanks for reporting,
good news
g1junky said:
I flashed the desire z rom on my g2 yesterday after root, is my g2 now considered a desire z? if so it should be okay for me to follow these instructions right?
Click to expand...
Click to collapse
You've probably still got a G2 hboot, right ? Like the G2 eng hboot ? If so, then it's still really a G2 running a Desire Z ROM. But I can't answer your main question, I'm sure someone else will be able to though.
g1junky said:
I flashed the desire z rom on my g2 yesterday after root, is my g2 now considered a desire z? if so it should be okay for me to follow these instructions right?
Click to expand...
Click to collapse
No, your phone still has the G2 partition layout, so none of this is probably needed for you as your bootloader should already show S-OFF...
I have a g2 so most of this doesnt pertain to me, but as im trying to help someone currently stuck in a hard place thought maybe u could help.
My question has to do with after clockwork is installed. Why do u have to run wpthis.ko in recovery. Shouldnt wp be turned off in recovery? thats how the phone updates stock.
fastludeh22 said:
I have a g2 so most of this doesnt pertain to me, but as im trying to help someone currently stuck in a hard place thought maybe u could help.
My question has to do with after clockwork is installed. Why do u have to run wpthis.ko in recovery. Shouldnt wp be turned off in recovery? thats how the phone updates stock.
Click to expand...
Click to collapse
I just tested doing a nand restore without using wpthis-Z.ko and it *seems* to be working. I haven't flashed anything yet so i can't be sure but it seems like it worked
Sphaerophoria said:
I just tested doing a nand restore without using wpthis-Z.ko and it *seems* to be working. I haven't flashed anything yet so i can't be sure but it seems like it worked
Click to expand...
Click to collapse
Well, for me it was able to flash system, but not boot. My guess would be hboot wouldn't work either. [Obviously it won't return an error... It will think it had written, when in fact it hadn't.]
As for the post before that, the fact that stock recovery can flash images says nothing about other recoveries being able to do the same. Stock recovery could disable wp for example.
In any case it would be nice to have permanent write-access...
stridger said:
Well, for me it was able to flash system, but not boot. My guess would be hboot wouldn't work either. [Obviously it won't return an error... It will think it had written, when in fact it hadn't.]
As for the post before that, the fact that stock recovery can flash images says nothing about other recoveries being able to do the same. Stock recovery could disable wp for example.
In any case it would be nice to have permanent write-access...
Click to expand...
Click to collapse
Dont take this as arguement, cause as ive said i dont have a z, just going by what ive thought to be right. With that being said, the fact that wp is off in stock recovery does say something. The bootloader is what sets wp on/off so if the bootloader is loading the recovery(which it thinks is stock) wp SHOULD be off. i guess a good way to test would be after a nandroid, flash a zip thats only a boot.img and see if it takes.
Heres another question then, what about using the g2 eng recovery?
stridger said:
No, your phone still has the G2 partition layout, so none of this is probably needed for you as your bootloader should already show S-OFF...
Click to expand...
Click to collapse
i tried the G2 method for obtaining clockwork and it didn't work it says it flashed from the app but when i try to backup rom im still on the stock recovery.. would u recommend i try the D-Z method?
fastludeh22 said:
Dont take this as arguement, cause as ive said i dont have a z, just going by what ive thought to be right. With that being said, the fact that wp is off in stock recovery does say something. The bootloader is what sets wp on/off so if the bootloader is loading the recovery(which it thinks is stock) wp SHOULD be off. i guess a good way to test would be after a nandroid, flash a zip thats only a boot.img and see if it takes.
Heres another question then, what about using the g2 eng recovery?
Click to expand...
Click to collapse
wp is definately off in recovery but the problem is probably "your update-binary or updater-script (don't use update-script)" in koush's own words. Anyways i hope we find a way around this soon
FYI: Method updated to reflect the fact that we now have an ENG hboot.
stridger said:
Follow G2 guide on http://forum.xda-developers.com/showthread.php?t=833965, but instead of wpthis-*.ko use the file http://content.modaco.net/dropzone/wpthis-Z.ko. ALSO DO NOT FLASH THE hboot-eng.img INSTEAD USE THE FILE ON http://www.multiupload.com/4U9P14R86Y. IF YOU FLASH THE WRONG FILE IT COULD POTENTIALLY BRICK YOUR DEVICE! .
Click to expand...
Click to collapse
Good work.
Just a suggestion, but I think it would be a lot clearer if, instead of two lots of "follow this except don't do this bit", you were to copy out the whole procedure and change those two bits appropriately ?
Just trying to help minimise the chances of bricks.
steviewevie said:
Good work.
Just a suggestion, but I think it would be a lot clearer if, instead of two lots of "follow this except don't do this bit", you were to copy out the whole procedure and change those two bits appropriately ?
Just trying to help minimise the chances of bricks.
Click to expand...
Click to collapse
Yes, I agree and would like to do that, but wanted to ask unforgiven512 first to integrate it into his guide, as it seems to much overhead to maintain two guides of essentially the same procedure...
Now both devices have a fully working eng bootloader, we really need to merge these two forums into an "HTC VISION" one!
Hi guys,
I've been reading through the forums over the past two days but I have to admit it's hard to find what I am looking for now that the G2 forum and the DZ forum are merged, and the search isn't getting me anywhere for this one.
I have Bell Canada Desire Z permarooted and S-OFF'd, with CWMod. I did this before the newer gfree method and from what I can gather this can lead me to some kind of endless loop if I try to flash back to the a Bell RUU or other RUUs for that matter. It also worries me that I can't try new radios, etc.
I am getting very poor battery life compared to others so I want to have my phone replaced. I have an extended warranty from FutureShop so I probably don't even need to reset the phone to stock again (they swap on the spot) but I would like to anyway. It will also allow me to test the battery again with the stock ROM.
So, how do I go about flashing back to the Bell ROM and turning S-ON, and unrooting? Keeping in mind that I used the pre-gfree method. I believe it was Visionary R12 and gtab's guide.
Also as the title implies, I was wondering if it's possible to use the new (better) S-OFF even if I am already S-OFF'd the old way?
Any help is appreciated!
You can use gfree and achieve "real" S-OFF without having to unroot.
Just run it. Worst that'll happen is it fails if you happen to be on a kernel it doesn't like. If this happens, no harm is done, just a reboot.
Just run gfree from where you are, as the previous poster said.
That will put you in a much safer position, where you can get stuck in that boot loop that you can if you've only got the eng hboot.
Then you can flash whichever ROM you want. Then you can undo gfree if you want via its new options (see the Wiki).
Regarding your point about the merger, IMHO this issue isn't anything to do with the DZ specifically, and lots of users are posting about similar stuff with their G2s. It's all the same
Thanks guys,
I've done gfree (which is MUCH easier than the thread and wiki make it look - they need to simplify the text, it's overwhelming to look at given how simple the procedure is) and flashed the Bell RUU.
Now I am just about to root, and use gfree to undo the S-OFF I guess?
Will let you know how that turns out. Thanks again!
Ok,there is a new gfree method to get root and S-Off.
And gfree can now also be used to set radio S-ON.
But what about the backup "part7backup-1291675121.bin"
which gfree created at my sdcard?
No longer needed?
And with the new root and S-Off method,is it now possible to
to flash stock RUU 1.34.405.5 to get all original?
Because with old UBERROOT method this doesn`t work!
Ganii said:
Ok,there is a new gfree method to get root and S-Off.
And gfree can now also be used to set radio S-ON.
But what about the backup "part7backup-1291675121.bin"
which gfree created at my sdcard?
No longer needed?
And with the new root and S-Off method,is it now possible to
to flash stock RUU 1.34.405.5 to get all original?
Because with old UBERROOT method this doesn`t work!
Click to expand...
Click to collapse
I'd keep that backup file as it is a dump of your original partition 7 before gfree mods it. You can dd i back and put everything back to how it was, if you ever need to. Do you need to keep it on the phone? No.. store it somewhere on your PC.
With the old "fake" S-OFF you would get stuck if you flashed a stock rom because it would overwrite the engineering HBOOT which was the only thing making your phone think it had S-OFF. With gfree method, you have real S-OFF, so this should be fine.
See http://forum.xda-developers.com/showthread.php?t=838484 for details.
tl;dr You should be fine.
Hm,little bit confused!
The backup I need to get original original partition 7
but not to get S-On.
To get S-On I can use the new gfree method,it`s now
possible with this!
I did the old UBERROOT method with real S-Off!
P.S.I read here about this:
http://forum.xda-developers.com/wiki/index.php?title=HTC_Vision#Rooting_the_G2
Not 100% sure I understand the question...but:
You don't need that backup file. If you delete it nothing bad will happen. Paranoid people (like me) would copy it to a safe place, but there's no real need.
You can flash whatever roms you like, including stock ones, as long as you have real, radio (gfree) S-OFF.
Hi guys, thanks for the help! I got it all settled, it was easy.
As I mentioned above, I used gfree to do a true S-OFF, which was easy.
Then I ran Bell's RUU and it worked without any issues. I assume the RUU install also flashes the HTC recovery back to the phone, I didn't check but it must..
A little summary for anyone who needs help in the future..
If you rooted/S-OFF'd using a method older than the current rage/gfree method (the one in the wiki) then you need to redo the S-OFF using gfree.
Steps:
Use gfree -f to S-OFF again
Run the stock RUU file on your pc (you need HTC sync installed for this)
Temproot (first part of the wiki guide) the stock ROM
Use gfree -s on to S-ON your phone
Reboot, and everything should appear like stock (aside from still being sim-unlocked).
Were u sucessful in returning your phone to htc after u did the above?
I didn't have to return it to htc, just to future shop, and it was fine.
Sent from my GT-I9000 using XDA App
Hi guys and gals, today we're going to talk about getting a Desire Z to S-On, but first here is a bit of background...
I rooted my phone using rage/gfree v1 or v2 in december 2010. That produced a partition 7 backup which I still have.
I also made a nandroid backup after rooting and installing CWR which I still have.
I have succefully removed Superuser.apk, un-rooted, put back original h-boot and orignal rom 1.34.666.5.
I cannot complete the final step; getting back to S-On. Here is what I have tried:
1) Get temp root with psneuter then use gfree v6 or v7 to reload my partition 7 backup. Did not turn s-on
2) Get temp root with psneuter then use Gfree to turn s-on. Did not turn s-on
3) Other threads about getting S-on talk only about the t-mobile G2, Not the DZ for example...
The part of the wiki that discusses returning to S-On is only applicable to T-mobile G2s. Not the Desire Z (http://forum.xda-developers.com/wiki/index.php?title=HTC_Vision#Unrooting_and_Returning_to_Stock)
A few other guides talk about the T-mobile G2 but not the DZ (http://forum.xda-developers.com/showthread.php?t=835971&highlight=unroot)
Other guides deal with cases where you rooted using visionary which I didn't (http://theunlockr.com/2010/12/01/how...g2-htc-vision/)
Potential hints:
-I do not know which radio I had back then
-I am trying to get S-on after removing eng-hboot
What do you suggest I try?
Restoring your part7backup with gfree should work, you need to be on a 1.34 rom, and have a radio version at 26.03.xx.xx or lower.
Those guides for the G2 should work with the DZ also, seeing as they are identical devices (only difference is the hboot)
-Nipqer
is it safe to just run the RUU files instead to go back to stock form?
Running a stock RUU will return you to full stock (hboot, recovery, system)
BUT you will still be S-ON if you used gfree.
-Nipqer
Flash05 said:
is it safe to just run the RUU files instead to go back to stock form?
Click to expand...
Click to collapse
its safe and it's the fastest way!
but you will return to stock 2.3.3
I had a similar issue months ago (partition restore didn't work), in the end I went the whole way and got PERM-root.
In Terminal Emulator I typed the following:
Code:
/data/local/tmp/gfree -s on
sync
After that I rebooted into the bootloader to check if it'd worked and if it did I flashed the PC10IMG.zip I used in the rooting process to reset it.
d_gkal said:
its safe and it's the fastest way!
but you will return to stock 2.3.3
Click to expand...
Click to collapse
It depends on which RUU you run actually...
If you get the latest, then yeah you'll be on 2.3.3, but you can easily find froyo ones to use.
-Nipqer
Nipqer said:
It depends on which RUU you run actually...
If you get the latest, then yeah you'll be on 2.3.3, but you can easily find froyo ones to use.
-Nipqer
Click to expand...
Click to collapse
im on 2.3.3 GB OTA. can i run RUU with 2.2 so that i dont go thru the hassle of downgrading, running these and those... then from here root then custom ROM?
No, you need to modify the misc partition, which is where the version information is stored to allow a downgrade.
Even RUU's check if its newer or older before flashing.
-Nipqer
If you use the ruu, won't your telephone brick?
Sent from my HTC Vision using XDA App
double post
I'll try Scythes method tonight and report my results. I was gone this weekend so I couldn't play with it.
Scythe01 said:
I had a similar issue months ago (partition restore didn't work), in the end I went the whole way and got PERM-root.
In Terminal Emulator I typed the following:
Code:
/data/local/tmp/gfree -s on
sync
After that I rebooted into the bootloader to check if it'd worked and if it did I flashed the PC10IMG.zip I used in the rooting process to reset it.
Click to expand...
Click to collapse
Thanks
Should probably reset your cid as well...
you can find it by doing
Code:
dd if=/dev/block/mmcblk0p17 bs=1 count=8 2>/dev/null; echo
in adb shell, or terminal emulator.
then set your cid with
Code:
./gfree -c <cid here>
Note: CID is an 8 character string.
-Nipqer
Koopabro said:
If you use the ruu, won't your telephone brick?
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
why?
10 chars
ok i have the same problem with an AZERTY Desire Z.
Now i don't have the original ruu, however I made a backup using dd to copy all the images to the sdcard. I don't have a backup of partition 7 though.
Here's the deal:
Went from a stock rooted gingerbread rom to stock 1.82.1100.7 rom (froyo). Stock recovery and radio restored. Everything is stock except, you guessed it, hboot. Can't get S-ON back. I tried the method in the wiki and it still wouldn't turn S-ON. I also have SuperCID eventhough i tried the gfree method to get CID back to stock (HTC__E41).
I tried upgrading to the latest stock 2.3.3 rom, but the hboot still stayed S-OFF. Which is a good thing since I am able to get CWM back and return to the froyo 1.82 rom. Once I was back, I also tried restoring a stock hboot but that didn't change anything.
So any suggestions? How can I get this device back to S-ON?
yozgatg said:
I tried upgrading to the latest stock 2.3.3 rom, but the hboot still stayed S-OFF.
So any suggestions? How can I get this device back to S-ON?
Click to expand...
Click to collapse
And i also have cid 11111111
I have to send the phone back cause of continue freezes but i think sending it with s-off and supercid won't help me to get it changed by guarantee
me too failed to get the S -on back again...
i am still figuring on how to do that for 2 weeks already...
basically read everything, tried what i am allowed. but to no avail...
i heard that people do send the phone with s -off for guarantee repair..
my ear speaker is not working anymore while in the guarantee period.
sad...
sevensaints said:
i heard that people do send the phone with s -off for guarantee repair..
my ear speaker is not working anymore while in the guarantee period.
sad...
Click to expand...
Click to collapse
I've sent mine with supercid and S-OFF and they repaired it with guarantee without any problem !!
The ear speaker was not broken by the rooting process, am i right ??
I couldn't get s-on or CID back to the bell CID.
I sent it in for repair for the second time. I'll keep you guys updated...
I sent my phone for repair of the BSOD (black screen of death) a second time. It was S-Off and superCID since I was incapable of returning them to stock. Nevertheless, they replaced the motherboard of my phone and it was covered by the guarantee (confirmed by the new serial number). Unfortunately, the issue is still occurring.
Hi everyone
I was advising somebody on rooting their Desire HD.
We got as far as installing the 1.32 stock ROM and I stupidly (and now I regret it so damn much) forgot about radio S-offing the device first so we tried Eng-S-Off. That said do not turn off the device because the bootloader is corrupt.
Then we tried the Radio S off tool and that said Unknown error, possibly connection.
How can we fix this?
EDIT: Will installing an RUU fix it?
raze599 said:
Hi everyone
I was advising somebody on rooting their Desire HD.
We got as far as installing the 1.32 stock ROM and I stupidly (and now I regret it so damn much) forgot about radio S-offing the device first so we tried Eng-S-Off. That said do not turn off the device because the bootloader is corrupt.
Then we tried the Radio S off tool and that said Unknown error, possibly connection.
How can we fix this?
EDIT: Will installing an RUU fix it?
Click to expand...
Click to collapse
Ya it will just do that way and do the rooting again after following these steps.....
find the stock splash screen here: http://forum.xda-developers.com/showthread.php?p=15430340&highlight=stock#post15430340
Uncompress that and put the .img file in the same folder as your fastboot file (in the Android SDK, it used to be in the Tools folder but nowadays they put it in the Platform-Tools folder), then open a CMD window, (Make sure the file is called splash1.img) and type:
fastboot flash splash1 splash1.img
That will restore the stock splash screen.
To restore the software you have to:
1: Find a 1.32.405.6 RUU that matches the original state of your phone. 2: Flash that RUU 3: Use Visionary R14 to Temproot and then Permroot 4: The Jkoljo's Easy Radio Tool to change the CID back to stock (If you phone was unbranded it will be HTC__001)
Now its ready to root again...
Hope that helps.
No I'm saying because the bootloader is corrupt, will installing an RUU restore the original bootloader?
There is no custom splash screen. We got as far as installing the 1.32 ROM.
raze599 said:
No I'm saying because the bootloader is corrupt, will installing an RUU restore the original bootloader?
There is no custom splash screen. We got as far as installing the 1.32 ROM.
Click to expand...
Click to collapse
I honestly think people are just copying and pasting stuff they've read somewhere without thinking about what they're saying. The bulk of that is nothing to do with the query you asked (apart from maybe the line about the RUU); I mean, replacing the splash image?! How's that going to help with a corrupted bootloader? Let alone telling you to download the full Android SDK just for that
On topic: the RUU should do it, but I've never tried it myself so you're probably safer waiting for someone with some actual experience to confirm before you flash. I have seen that error mentioned in one of the guides I used back when I rooted (January time), so I'll see if I can dig that out.
//sent from my Desire HD using Tapatalk; all errors entirely intentional.
---------- Post added at 08:07 AM ---------- Previous post was at 07:42 AM ----------
Okay, found it: a few people were having "bootloader corrupt" issues using the One-click ENG S-OFF tool.
Try the advice in that post (or maybe search that thread a bit further for mentions of "corrupt") before you waste time flashing a RUU. IIRC you can do Radio S-OFF & ENG S-OFF in any order (the ENG S-OFF tool has a box to tick whether you have Radio S-OFF or not); I don't think that's the problem here.
Thanks I will try that later. It seems like from the thread that if you didnt get a superuser message on the phone, nothing actually happened to the bootloader. We didnt get a superuser message on the phone. So could it be a false alarm and safe to reboot?
EDIT: By the way what the other user copied and pasted, I wrote originally lol but I didnt want to say that then in response.
raze599 said:
Thanks I will try that later. It seems like from the thread that if you didnt get a superuser message on the phone, nothing actually happened to the bootloader. We didnt get a superuser message on the phone. So could it be a false alarm and safe to reboot?
Click to expand...
Click to collapse
Yeah, that should be fine. If you didn't allow it root access when you ran it then it's not going to have been able to do anything. Reboot, clear the request in your superuser app and start again.
You don't mention it, but I assume you've already used Visionary to permroot before you tried the S-OFF tool? Just a thought when you mentioned you didn't get the su request on the phone.
raze599 said:
EDIT: By the way what the other user copied and pasted, I wrote originally lol but I didnt want to say that then in response.
Click to expand...
Click to collapse
Lol this is quite funny. I was actually instructing him over skype and then when I left Skype last night he did something and it worked lol THANK GOD!
I have no idea what he did but wierd things happen when I'm not looking lmao
Still though, since we have had some major problems, do you recommend that we install an RUU and start again from scratch? Just to avoid any future problems?
EDIT: Yes it was Permrooted, the superuser came up when he tried it himself and it worked.
I wouldn't bother personally; as long as you're s-off it doesn't matter how you got there. It's not like the phone's going to be left half s-on or something.
Besides, why let him waste time redoing that when he should be using that time to flash a load of new ROMs
//sent from my Desire HD using Tapatalk; all errors entirely intentional.
Thanks very much
So i called in for the warranty today since my phone's screen has been having some troubles and i need to send it in....I tried flashing to the PC10img.zip from the bootloader but that just ended turning my S-ON and not flashing me to the stock original room(main version is older).So basically im wondering what my options are here...I am able to switch between the CM7 ROM i had and the latest 2.3.3 stock rooted rom i found(which is not good enough since it shows the superuser app, any way to hide this?Can't really download apps since the market crashes for some reason) anyways i'd really rather be able to go to actual stock UNROOTED state but i think i might have messed it up.Anybody know my options here?
Do you have a rom you can boot into at the moment?
If yes, boot into it, and run misc_version to change your version number, so the restore can go through.
Otherwise, flashing the latest OTA should go through without a 'main version is older' error.
-Nipqer
And how exactly do You run misc_number?if it that hex editor process through the pc I tried the commands in terminal emulator and it said something along the lines of permission denied.if you could please direct me to a step by step guide to be able to do this.
http://forum.xda-developers.com/showthread.php?t=1178912
its the second part: Changing Version Number to Allow Downgrade
if i helped you pls use the thanks button (i want to have 10 thanks meter )
EDIT: another guide: http://forum.xda-developers.com/wiki/index.php?title=HTC_Vision#Unrooting_and_Returning_to_Stock