Develop Bugs

Hard SPL Problems

i'm trying to upgrade to VP3g's rom and every time i install the latest version of hard spl it says its not detectable or it says unknown version use safe spl. i follow the mrvanx guide everytime,...... whats wrong???????????????????

nothing, go ahead and continue. I'm sure everything will be fine. It's happened to me several times with different Roms but I had no problems flashing.

choose spl version, if hard spl v7 choose 2.10 then continue

kazuya_gonzalez said:
choose spl version, if hard spl v7 choose 2.10 then continue
Click to expand...
Click to collapse
i bricked my phone..............

edited , double post

Symbian_Black said:
i bricked my phone..............
Click to expand...
Click to collapse
are u sure have hard spl v 7? (2.10 olipro?)
i also have a problem that cannot detect my version..
but i choose version 2.10.. and it works for me for upgrade any rom..

I don't what you did but if you have HardSPL on your device then you haven't bricked it. Put it into Bootloader Mode (Tri color screen) and connect it to your computer. Get a Rom , try Schaps, and run the RUU Wrapper. If you have HardSPL on it then you should have no problems.

i have also this problem but i klick the version of my spl and it works

aint nffin wrong laddie
all will be fine
if it dont auto detect it will default to safe
but check the next screen to see if it reads correct

Newbie with 1 big question

Dear All,
first of all....HELLO! I've just registered myself on the forum.
Yesterday I bought the HTC P3600 (Trinity, I think), english version (I suppose it's called wwe). I want to install a cooked ITALIAN ROM, but I read I'm losing the guarantee if I'll do it.
Somebody tell me there is a software that can allow me to re-install the original ROM and avoid the guarantee losing.
Is this right? can someone give me more info?
Thanks in advance for your reply and sorry for my english
Best regards

You can always go back to an original HTC rom, as long as you don't brick your device.
In order to prevent that, you should install a Hard-SPL (board search, iirc its a sticky) which is a replacement bootloader that allows flashing any Rom after bricking.
Have fun playing around with your new P3600.

ZakMcRofl said:
You can always go back to an original HTC rom, as long as you don't brick your device.
In order to prevent that, you should install a Hard-SPL (board search, iirc its a sticky) which is a replacement bootloader that allows flashing any Rom after bricking.
Have fun playing around with your new P3600.
Click to expand...
Click to collapse
So if I install first the Hard-SPL I can install a COOKED ITALIAN ROM and after I can go back the original HTC ROM and I'll not lose my guarantee???
If I brick, how can I de-brick the HTC?
Thanks for the quickly reply
Best regards

You should try reading the WIKI and also check www.trinityguides.info

Helloo there.
Your phone is probably cid locked, that means, that u can install only original htc rom-wm5. wm6 doesnt exist for htc trinity.
If u have cid unlocked, u can flash any rom with the RUU (rom update utility) , which is in the package with the rom.
Otherwise i prefer for my cid locked trinity that:
http://forum.xda-developers.com/showthread.php?t=293632
U loose warranty if u send the broken pda on service with the custom rom installed on it. So, before u send it, flash the original rom over and it will be ok.
The problem could be, if the lcd goes bad, than its hard to reinstall the original rom. i know u understand.

badguy999 said:
Helloo there.
Your phone is probably cid locked, that means, that u can install only original htc rom-wm5. wm6 doesnt exist for htc trinity.
If u have cid unlocked, u can flash any rom with the RUU (rom update utility) , which is in the package with the rom.
Otherwise i prefer for my cid locked trinity that:
http://forum.xda-developers.com/showthread.php?t=293632
U loose warranty if u send the broken pda on service with the custom rom installed on it. So, before u send it, flash the original rom over and it will be ok.
The problem could be, if the lcd goes bad, than its hard to reinstall the original rom. i know u understand.
Click to expand...
Click to collapse
Thanks for your answer. I installed the SPL-1.20 and I updated my Radio version (1.46.00.11------is it good?). Now I can install every unofficial ROM and in any case I can go back (how?).
Is it right?
Best regards

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810

Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help

Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.

If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included

Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.

You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU

I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!

Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.

band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?

Here you go....I did a search

Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!

Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4

band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...

kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.

f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that

f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.

Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??

R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?

f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...

f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

Hard spl problem!!!

I know you guys most be tired of this but im still a lil confused about all this since i have searched around and i have still to know how to return the stock SPL...now i know theres alot of post that show how but what i need to do is find out one which i dont have to use my phone:
What i mean is....i dont have to copy SSManual.bat to my fun and run it from my phone...because i have to return my phone to HTC for warranty reasons but i cannot get passed the align screen configuration at boot since my touch is messed up (p.s. i can still flash and active sync)...
what i need to know is a way to return to the stock SPL without using the phone (except for Active Sync)...
p.s. if i have the ASIA WWE HK ROM on the SPL would be 1.34 or 1.93?
thank you!!
[SOLVED]
Basically, thanks to the ppl in this thread for helping.....since i couldnt get passed my align screen cause of hardware problems with my screen i couldnt access the sspl-manual in order to revert to stock spl so what i did is i flash my phone with Dia duit 1.4 which has no welcome screen or align screen so i could go thru to the phone then performed the sspl manual and reverted to the 1.93 spl (my version)and afterwards i flash my phone with the Asia HTC wwe orginal romhttp://forum.xda-developers.com/showthread.php?t=410720 ......i know ure supposed to first flash orginal rom and then the stock spl but i took a chance and it worked...THANKS u guys keep up the good work and now its up to HTC to fix my hardware....Hoping its on warranty

By the way right now im on Olinex 1.40
thank you again!!!

can't you install the hardspl through bootloader mode?

Unfortunately no, everytime i do either i get an error [202] or it goes straight to 100% but then when i check with the vol - and reset button it shows olinex 1.40

did anybody ever try to send it without reverting back to the stock spl ?

emy09 said:
did anybody ever try to send it without reverting back to the stock spl ?
Click to expand...
Click to collapse
Try to install a rom which don't have to align the screen. then you copy the file you wants from the phone.
Good luck

does anybody know of a rom like that that exists cause that sounds like a pretty good idea!!

hi
i had your problem and has olinex 1.40 anld like to restore hard spl
first you should install original rom on your device
then install original hard spl ( i try it )
download rom 1.93 WWE from the htc site (it should be 1.93)
then hard spl with it (copy sspl manual om your device run it then restart you device run it again then connect it to pc and run ruu
hard spl : http://rapidshare.com/files/215819452/1.93_Original.rar.html
sorry my English is not good

http://forum.xda-developers.com/showthread.php?t=493719

emy09 said:
does anybody know of a rom like that that exists cause that sounds like a pretty good idea!!
Click to expand...
Click to collapse
i think the new rom of suiller (diadiut 1.4) would do. you don't need to screen align after flashing.

azera_2000 said:
hi
i had your problem and has olinex 1.40 anld like to restore hard spl
first you should install original rom on your device
then install original hard spl ( i try it )
download rom 1.93 WWE from the htc site (it should be 1.93)
then hard spl with it (copy sspl manual om your device run it then restart you device run it again then connect it to pc and run ruu
hard spl : http://rapidshare.com/files/215819452/1.93_Original.rar.html
sorry my English is not good
Click to expand...
Click to collapse
I appreciate the help but the problem is that i cannot get passed the align screen of the first boot which means i cant run sspl manual since i cannot in the files from my phone.....also if i do flash the Dia duit 1.4 rom which does not boot with the align screen or welcome screen, dont i have to flash the original rom before putting the stock SPL !!.....thank you guys for the info

dead diamond when flashing custom rom

hi.
a have a big problem with my diamond. i try to flash a custom 6.5 rom from here, but i don't do hard spl. i had a stock rom on it before. now my phone don't start, even in bootloader.
is something i can do, or my phone is dead?

ktutza2006 said:
hi.
a have a big problem with my diamond. i try to flash a custom 6.5 rom from here, but i don't do hard spl. i had a stock rom on it before. now my phone don't start, even in bootloader.
is something i can do, or my phone is dead?
Click to expand...
Click to collapse
Hi i think its bricked then because a custom Hard-Spl is needed incase ov a bad flash, to recover and if you didnt Hard-Spl then its bricked. Sumone correct me if i'm worng

Hello.
help could only J-Tag.
or even try to correct HardSpl.
Sorry but my English is poor.

everything you need is on the forum, just search.

No sympathy.
ktutza2006 said:
hi.
a have a big problem with my diamond. i try to flash a custom 6.5 rom from here, but i don't do hard spl. i had a stock rom on it before. now my phone don't start, even in bootloader.
is something i can do, or my phone is dead?
Click to expand...
Click to collapse
You tried to flash a custom rom without SPL. What where you thinking? That you knew better?!
get an I phone.