Greetings for the new year folks !!!
I have an X50v upgraded to WM6 ROM.I linked it to a Rocketfish bluetooth headset RF-MAB2.
Initially everything ran smoothly.
Now I used the old pairing information to reconnect and it says something like " cannot connect to the headset ..authentication failed " . I removed the pairing, put it in pairing mode again ( the BT Headset ) and then tried to connect again - with the same pin 0000 - same problem.
Soft reset ..same problem.
Whats happening ..all of a sudden why did it refuse to connect .
Did anyone run into the same problem with any headset...
Related
Hi, I've a problem with my qtek 8020 with 2.2.32.23 rom.
My smartphone doesn't recognize bluetooth car handsfree (metablue) automatically, after a pairing and a connection (that run perfectly) when I turn off the handsfree or the 8020, and put on, the connection doesn't start automatically, and I must cancel the connection and re-pairing again.
The handsfree runs perfectly with a symbian phone, therefore it's probably a bluetooth stack problem of my 8020.
Please, has anybody a solution?
Thanks all.
Hi all,
i am runing my trinity with WM6 and AX3l's rom. my issue is that i cant connect to my car stereo which is a pioneer DEH-P55. My trinity see's the stereo and gives the option for hands free but the stereo cant detect the trinity. my device is visible to others but the stereo wont pick it up. Any suggestions for a fix on this would be appreciated.
thanks
corm
maybe you have to push a button on your radio to activate first time pairing, that was the solution for my bluetooth headset.
(pairing from both sides)
just a suggestion, maybe it helps.
Try the Jetware bluetooth extension it has a 30 day trial and worked for my Alpine headunit its at http://www.jetwaremobile.com/
Thanks for the replies, but still no luck. I can pair other phones to the stereo but not this. Are there any settings that i may need to activate on the device that i am missing? its abit infuriating as i need to get this up and running as soon as.
rgds
Corm
activated "receive all incoming beams" ? its in settings/connections/beam
its already activated stormyb but thanks again for helping.
I always had problems using bt and irda...
I never succeed send/receive any file using my pc (my pc irda always worked fine with others devices). Beam enabled on commManager and on settings "receive all incoming beams".
When I try to connect (pair) using (htc) BT I get this error: the connection failed or the passcode is incorrect...
---
One time I tried to send a file to a nokia phone and I needed 30 min to succeed: restart phone, restart BT, restart beam, restart phone, restart nokia, restart BT, restart, restart, ....
Now I'm using the radio 1.46.00.11, rom eLiAs2.11wwe (before I was radio 1.38 and udk rom) and when I pair from htc, on pc I don't receive the pin request. If I pair from pc, I see the request for pin no htc but when I type it: "the connection failed or the passcode is incorrect".
Only one time I was succeed pair (and saved on device list), I typed 3 times the pin code, but after I can't transfer files...
From pc, I see the htc on the device list, if I try the ftp service, htc ask me: "xxx wants to connect with your device using bluetooth. Do you want to add XXX to your device list?" I answer yes but when I insert the pin, the pc give to me this error: "error establishing the connection"
If i try the voice gateway, after type the pin on htc I get this error on pc:
"the remote device closed the connection"
Using this last rom, when I try beam a file, I can't see my pc irda (using the udk rom I can to see but without success), I only see my pc BT but always "failed" the connection.
Nobody has the same problem?!
What bluetooth comms are you using, windows or Widcomm's?
I installed widcomm onto my laptop as I was suffering the same problems as you mention and I couild not get a bluetooth serial port setup either, once installed and restarted the pc then I just powered up both BT's and set the phone to visable and the laptop found it straight away with all the services and could setup the serial port.
I seem to recall there are numerous problems with most BT's when using the default windows drivers etc..
HTH's
hi, I'm using widcomm...
I didn't test again a bt headphone, but I have problems trying to connect to a nokia phone for example (n95, n73).
The irda never works... I tried too with a nokia phone and a remote control software for wm6... nothing...
All ok using headset BT...
I installed blueSoleil BT driver and now it is ok.
same ppc, same rom, same problem with my bt bury in the car and with other ppl's triyng to bt connect to my ppc. i can "see" them they can "see" me but there is no transmission TO me. I can send.
i am using the bt phone (bury) but onlt when I initiate the connection. i think it's a rom bug.
I keep losing the pairing on my bluetooth devices whilst running WM6 after a soft reset.
When go to settings/connections/bluetooth the pairings are still there, yet after a soft reset I get message up "Do you wish to allow this device to connect Y/N"
Any ideas ??
Had the same problem myself (kept dropping connection - ok for 1st call then wouldn't connect) and i went back to wm5. Not had any problems since then.
Yeah thats what i've done lol
I have a bluetrek S2 headset, Since I flashed my MDAC III to WM6(B&B) I'm having problems keeping the headset and my device paired. I flashed WM6.1(B&B5.0) to the device but the problem still exist. I can pair them to each oter, and everything works fine. When I turn of the headset( to recharge or to save battery) The connection is lost the next time I turn it back on, I do have to pair them again. First I tough it was my headsets problem, but then I tried to pair a BT GPS mouse, the same result. I have the same problem pairing this GPS with other devices(TyTN, iMate Jamin) running WM6. Does anyone know how to fix this bluetooth problem I'm having?
There might be a connection here (no pun intended). For quite sometime, I was using an old SE637 phone and had it working flawlessly with my Garmin c550 GPS.
During an hour and a half trip yesterday, the Garmin notified me 3 times that the bluetooth connection with the Tilt was lost (the SE profile had already been removed from the Garmin). I never saw this message before with the SE. FWIW, the 2 devices are no more than 2 or 3 feet apart at all times, and neither of them are physically touched during the trip. I'm concerned that this might be an HTC problem. Any thoughts?
smonte said:
I have a bluetrek S2 headset, Since I flashed my MDAC III to WM6(B&B) I'm having problems keeping the headset and my device paired. I flashed WM6.1(B&B5.0) to the device but the problem still exist. I can pair them to each oter, and everything works fine. When I turn of the headset( to recharge or to save battery) The connection is lost the next time I turn it back on, I do have to pair them again. First I tough it was my headsets problem, but then I tried to pair a BT GPS mouse, the same result. I have the same problem pairing this GPS with other devices(TyTN, iMate Jamin) running WM6. Does anyone know how to fix this bluetooth problem I'm having?
Click to expand...
Click to collapse
No one with an possible solution, or at least with the same problem??
Same problem here
I have just received a new HTC TyTN II on Orange that has the same problem. My old one (windows mobile 6.0) had no problem with my Motorola H12, but the new one (Windows Mobile 6.1) can't keep the pairing, and I have to turn Bluetooth on an off to get the connection. Always have to enter the passcode.
Version data is:
CE OS 5.2.19212 (Build 19212.1.0.3)
Processor: MSM7200-400MHz
ROM version 1.65.16.25
G 25.83.40.02H
D 3.28.00.00
Any help /advice much appreciated!
O.
Fixed itself...
This seems now to have fixed itself - I had to enter the password twice in a row for some reason and then it worked properly. So now all happy...
Windows Mobile 6.1 rocks...
I currently have a Diamond and TP2 with stock ROM's.
Diamond worked perfect with carkit untill i performed major ROM upgrade from htc.com. now it will connect and not reconnect on either device or carkit restart.
My TP2 behaves EXACTLY the same - connects and drops after either restarting. when connected it works fine - voice/dialing etc etc.
My car kit is a JVC KS-BTA200 connected to my KW-AVX810 head unit.
i've read all comments on google/xda's etc - well almost all! to no avail.
the devices are all set to visible obviously and all paired. ive read that a registry edit possibly fixes the issue but my TP2 & Diamond dont have the required reg strings. (that i can find!!)
i have the remote registry tool installed on my Desktop - so im ready to make changes!
please, if anyone can help i will very grateful!!
radak23 said:
I currently have a Diamond and TP2 with stock ROM's.
Diamond worked perfect with carkit untill i performed major ROM upgrade from htc.com. now it will connect and not reconnect on either device or carkit restart.
My TP2 behaves EXACTLY the same - connects and drops after either restarting. when connected it works fine - voice/dialing etc etc.
My car kit is a JVC KS-BTA200 connected to my KW-AVX810 head unit.
i've read all comments on google/xda's etc - well almost all! to no avail.
the devices are all set to visible obviously and all paired. ive read that a registry edit possibly fixes the issue but my TP2 & Diamond dont have the required reg strings. (that i can find!!)
i have the remote registry tool installed on my Desktop - so im ready to make changes!
please, if anyone can help i will very grateful!!
Click to expand...
Click to collapse
Hi, I am using my Touch Pro 2 with the same HU and Bluetooth adaptor as you but no such problem so far.
It used to have this problem then I try to connect using Window CE as the phone setup and choose another Connection Key instead of default 0000 to pair the phone with the HU.
ok, well i just tried connecting via searching for the device from the HU. it finds my device - i tap enter (to connect on HU) then it just jumps to a blue flashing 'connecting' then goes to a yellow 'error' straight away. if i select 'open' on the HU then it connects (connecting with a different ID - a number '6') but only untill i restart the HU.
also as a test i just tried an Xperia (just had one laying around LOL) and it does the exact same as mine!! ARRRRGHHH!
so im glad to say i believe it is not an HTC issue!
ok so i have an update - the problem is my HU will not pair correctly and it will not store a pairing. great.
another quick one - have found others are having trouble with their HU/adapters. thanks anyway everyone!
TP2 Bluetooth and voice dialing working fine ???
Have you tried to reset your carkit? I had the same problem after the rom-update with my TP1 and I put my carkit (Bury CC9060) back to factory settings. So I did the same this morning after I updated my TP2 and now it works just like a charm. Of course I don't know if your carkit has this possibility. Good luck, greetz Ton
'iznogoooog' - yes it work perfectly until you restart either device - 'ton66' - unfortunatley a reset is pretty much all i can do!!! eeeeek!
hopefully a reset will fix it! - i did unplug my b/tooth adapter then switch the unit on - then off then plug it back in.. didnt change anything.. oh well! will do complete re-set 2day!
BTW:
thanks so much for everyones help!
Got a questions. I am using the AVX-826 with build in Bluetooh. I want to know if you guys get the Signal Strength show on your Head unit is correct. on my unit pair with TP2. The Signal Strength indicator doesn't move. it always show the strength with my phone is connected to the unit and it stay that way.
The Battery Strength indicator does work and show the correct battery level.
I have exactly the same prob!
Hi,
I have a AXV800 and a BTA200.
My first device was a Artemis with WM6.0. No problem so far!
Then I changend to a Diamond with WM 6.1 and had the same problem as mentioned before. Now I tried my new TP2 and still the same problem.
And I tried the old Artemis again with a new 6.1 ROM and the same problem as on the other two phones.
Now I think it depends on the WM build. 6.0 seems to work 6.1 not!!!!!!!!!!
I did a reset on my AVX800 two times without luck!
I think I'm going to use a normal phone without Windows mobile for the next test!
Schelbi.