Hi,
i have to use the reset button quite often. unfortunately everytime the phone hangs i have to remove the back cover in order to reach it.
has anyone ever tried to drill a hole in the cover at the position of the reset button. if yes, is it save or is it likely that the the cover breaks during that procedure? is there a replacement cover available in case one does not succeed?
Not having one myself (yet) I cannot speak intelligently about the modification. There is a replacement cover available though:
http://www.expansys-usa.com/d.aspx?i=179102
yes, you can buy replacement cover.
and yes, drilling will work fine, just pre-drill with small drill first, like max 1mm, before moving on to whatever you wish.
Related
I'm curious to know if you can get it back together with all the seems as tight as when it was new. I want to get a new case off ebay but I want to know if there's problems with if fitting together again after it's been disassembled.
I was able to do it. It came out pretty good but I did slightly bend the metal edge of the new frame when I had to reopen it to align the reset button cover. But it's so slight, no one would ever be able to tell but me. All in all, it wasn't too bad, but it was just nerve racking having your $500 phone ripped apart and wondering if it will work when you put it back together - if you can get it back together. I was so relieved when I got the WM screen again!
A few pieces of advice:
For one, the instructions I read just said to disconnect the ribbon cables. Well it doesn't say that all you have to do is flip up the little plastic part to release the tension from the ribbon. (figured that out the hard way)
Also, make sure the rubber covers for items like the mic and reset button line up before you resecure the board to the frame. You DON't want to have to reopen it.
My phone will now stay covered with an excellent silicone cover made by Boxwave. The cut-outs are precision - you can get to everything. Also, it fits nice and tight like a glove. And it's just thick enought to protect, fit in the carrying case, and allow you to use all the buttons easily, especially the scroll wheel. (my last cover was too thick to use it with the cover on) I don't want to have to do this surgery an my phone any time in the near future so this is staying on my phone.
Problem when change housing
Yesterday I've change my M700 housing with P800. But as we know, they have different button map.
Now, I am trying to set up a hotkey for the Call button (Green button),
ie, when I press the call button, an application of my choice would
start running. For that I need to change the default settings in the
registry of the Pocket Pc. Could someone tell me where the default
settings of the call button is stored in the registry and what all
values should I change in the registry so that I can setup the call
button hotkey. Any help would be highly appreciated.
Why not just download hbutton and map as many programs as you like to the other available buttons? I've got like 12 prog mapped to 5 buttons.
Edit: Oops. I missed the point of your post. The buttons are mapped differently.
I was experiencing random screen shutoffs after fitting my galaxy note 10.1 (2014) for a new case.
It took a while before I finally realized that the random shut offs were being triggered by the case, more specifically, when the edge of my case came in line with the edge of the tablet, which is an awesome feature when you have the cover covering the front of the unit.
But the problem is it manages to shut off screen regardless of which side of the unit the cover is on, as long as the edge of the cover is aligned with the units edge. This can be quite frustrating when trying to read while holding the tablet in certain orientations.
Questions: I was wondering if anyone else has experienced similar issues with their cases/covers (a little research seems to indicate this is not an isolated issue and many, if not all, cases/covers suffer from this issue).
1) If you have not, which cases/covers do you use? Do these cases resolve the issue by never aligning the cover to the same position when flipped backwards as when flipped forwards (i.e. skewed slightly short of the edge when in backwards position)?
2) If you have experienced this issue, how have you addressed it? Can you disable the magnetic sensor?
3) Would weakening the magnet in the case perhaps ensure that it was only sensed in the forward position?
SKida00 said:
I was experiencing random screen sback andk ffs after fitting my galaxy note 10.1 (2014) for a new case.
It took a while before I finally realized that the random shut offs were being triggered by the case, more specifically, when the edge of my case came in line with the edge of the tablet, which is an awesome feature when you have the cover covering the front of the unit.
But the problem is it manages to shut off screen regardless of which side of the unit the cover is on, as long as the edge of the cover is aligned with the units edge. This can be quite frustrating when trying to read while holding the tablet in certain orientations.
et in the case perhaps ensure that it was only sensed in the forward position?
Click to expand...
Click to collapse
yes i have the same problem. pick up A generic folio type case for my P600. Case looks and feels great. Auto wake works brilliantly when I open the cover, but there is the problem of The screen turning off when I flip the cover over to the back and the magnetic edges meet. Dunno how to fix this yet. Tried the magnetoff xposed module but that doesn't seem to work.
I got the Moko slim case and the same thing happens, what I did to circumvent the problem was to put my screen cleaning cloth between the case and the tablet. This prevents the magnet from locking the screen when completely folded backwards, the only thing is that this method will block the camera with the cloth. For me this is not a problem I don't see myself using the camera on my tablet when I can use my SGS3's camera, and this way I never forget my screen cleaning cloth .
I've read about this on other devices on various covers as well. they think it mah be due to the magnet not being properly shielded. dunno any fixes other than get another case.
I hade a cover for my old Ipad and it all so turn off the Ipad when I flipped over the cover.
It did turn out the problem was with the magnet and after getting a new one, the problem was solved.
My poetic slimline work perfectly no issues at all. Love the look and feel, I do want a carry slevee tho for more protection if I wanna bring it out of the house. Or even just to store in the house. But overall love this case.
Sent from my SM-P600 using Tapatalk
Get a piece of sheet metal (strip out a cheapie magnetic whiteboard , a few dollars at a variety store) cut to just less than the back of the tablet screen.
Cover it with a thin plastic film (to safeguard from cutting yourself)
It will adhere to the back of the screen magnetically and flatten the magnet's field
Now you can use the device with the keyboard tucked away behind the screen. (you may have to leave a small air gap say 5mm to 10 mm)
This does not affect the normal screen-keyboard functions when used conventionally
Same problem with Galaxy Tab A (Nougat)
There is an option in the tab to turn it off, but regardless what you choose, the tablet still responds to the magnet. Very annoying when you lay down your tablet flat. For now i just put something between the cover and the back of the tablet, like a handkerchief. This works for me, but ofcourse it's not a solution just a workaround. I'm still trying to find a solution.
Did you find any way to turn off the magnetic lock and unlock function? When I backfold my cover (aftermarket), it automatically locks my tab. Which is very irritating. I have Samsung galaxy tab S5e
There wasn't a good search result on a way to disable it via software or hardware mod so I thought I would post the solution I just did on my daughter's new tablet folio.
She has an old S3 Tab so the options are quite limited so figured modification was the only way. I ended up removing 3 magnets until I figured out which one actually did the on/off Hall effect. The smart thing to do would have been to use a magnet to find where on the tablet the Hall effect sensor was first, then remove just that magnet. The other magnets are for holding the clasp in place when the folio is open or closed.
I just cut an X over the magnet location, removed it, then filled it back in with hot glue. On her tablet, the Hall sensor was on the top left (fat arrow). It's annoying to have to do this but there's no other way. I tried the metal plate trick but that looked pretty bad and didn't always work.
Hope that helps someone
Ok this might seem a bit odd, but has anyone been able to stick anything to the back of this device? i have a magnetic tetrax Fixway mount that I love, and when i switched phones i had to remove the little metal button from my old phone, it was no longer sticky enough to go on the back, so i tried 2 different kinds of 3m tape and each time it seems to stay sticky on the part that attaches to the button, but after a couple of attach/detaches from the mount, the button comes off. So I ordered new buttons, and I think they may have been pretty old, cause they didnt feel very sticky, tried them anyway, same result. Really want this to work, but not sure I can get anything to stick that wont RUIN the back. I'm sure gorilla glue would work or something like that. Maybe I should just purchase a new back and keep it aside in case i sell the device I can just put it on?
each time i attached the button with a a squeeze thing for several hours to make sure it was stuck good and had time to set, but no luck. is there some stronger double sided tape that's relatively easy to get a hold of?
I think the problem is the surface is not smooth and leaves grease, dust and air between back and your button, try to use some soft cleaner and try again.
Another back cover and glue might work.
Buy a non intrusive case and attach it to that.
Sent from my A0001 using Tapatalk
Yes, I have one of the official case for the One, it's really thin and only $10 so you can put some glue on it without regret
If I put my thumbs on the screen and my index fingers on each side of the "S" from the Nexus logo and apply a little pressure my phone makes little pop noise like the plastic may be loose. Does anyone else's do this? Could it just be that it is plastic that it makes this noise and there is nothing wrong with the phone?
Thanks for any input.:good:
Bump
If you apply pressure to plastic it's going to deform slightly which would cause a noise like that, yes.
raptir said:
If you apply pressure to plastic it's going to deform slightly which would cause a noise like that, yes.
Click to expand...
Click to collapse
My nexus 5 didn't do that and it's plastic.
Sent from my Nexus 5X using Tapatalk
Mine does it but only if I hold it a certain way and apply pressure in an exact location. Since I don't do this as I use the phone it's a non issue for me. I'd say if it does it when you hold the phone the way you normally would when using it and it bothers you then return it and try again? Mass produced electronic devices will always have inconsistencies and defects. You'll have to decide whether or not it's acceptable.
Thanks guys. I appreciate the input.
git-sims said:
If I put my thumbs on the screen and my index fingers on each side of the "S" from the Nexus logo and apply a little pressure my phone makes little pop noise like the plastic may be loose. Does anyone else's do this? Could it just be that it is plastic that it makes this noise and there is nothing wrong with the phone?
Thanks for any input.:good:
Click to expand...
Click to collapse
Bump
mine does that too. I returned it, thinking it may be a factory defect. But it appears that the new one does that too. Just plastic. Once you put that in a case, you wont' hear clicking
I fixed the clicking sound by applying a strip of insulation tape on the inside of the back cover. Be careful though, just apply one layer, two are too much and lead to a gap between fingerprint sensor and back cover.
For me the clicking sound almost disappeared after 2-3 weeks.
dskvml said:
I fixed the clicking sound by applying a strip of insulation tape on the inside of the back cover. Be careful though, just apply one layer, two are too much and lead to a gap between fingerprint sensor and back cover.
Click to expand...
Click to collapse
Good tip! This made me realize that it's easier to fix rather then go back to the store and return it for a new one (which probably will have the same issue). It look quite easy to remove the back cover in order to mount the tape, even though I'm not that inspired to dissemble a newly brought product. Did you mount the tape's sticky side against the inside of the back cover? Or did you mount it against the battery? I'm not sure it matters.
R
Rickckck said:
Good tip! This made me realize that it's easier to fix rather then go back to the store and return it for a new one (which probably will have the same issue). It look quite easy to remove the back cover in order to mount the tape, even though I'm not that inspired to dissemble a newly brought product. Did you mount the tape's sticky side against the inside of the back cover? Or did you mount it against the battery? I'm not sure it matters.
R
Click to expand...
Click to collapse
I mounted it against the back cover. But i guess it does not matter, as you only need to close the gap between battery and back cover, so there is no more space for the back cover to move.
dskvml said:
I mounted it against the back cover. But i guess it does not matter, as you only need to close the gap between battery and back cover, so there is no more space for the back cover to move.
Click to expand...
Click to collapse
Tried this and moved the tape several times but I realized that the squeaking and clicking sounds kept on coming back. So I cleared it for tape and sent it in for repair. It turned out that my main issue was just at the fingerprint sensor where the plastic back cover were to tight on to the right side of the metal ring around the sensor. Couldn't get rid of it after all, but it sure was a nice try! it might be a solution to other units depending on where the noise is generated.
R
I picked up a Samsung brand keyboard cover for my 813 today and was very disappointed to find that the magnets in the keyboard would shut the screen off when you flip the cover over so you can hold the tablet and use it without the keyboard.
I researched but couldn't find a solution that was even remotely practical.
I figured out that if you fold the cover like I did in the picture, there's enough space between the keyboard and the tablet that it doesn't trip the magnetic switch.
The cover is still folded on a way it's designed to and doesn't feel any different when using it.
Hope this helps.
so i assume this problem is not for specific covers then, i got a 'Superfly' case+cover that works like those for the ipad ones from Apple. the cover rolls back to create a triangle stand. when i try to fold it all the way back to create a flat back, the magnetic also sleeps the tab. so the only way to use it and holding it is to roll it back and making it a stand and hold the stand itself.
very frustrating as sometimes i would like to fold the cover back and lay flat on table or on my palm but it just sleeps it.
only way to hold it on the hand is the like pic attached.
it seems like the sleep magnets are towards the left of the device, because when i close the cover half way where the right side of cover is still far from the screen, it puts it to sleep. same for the rear
sorry for thread jack though, i'm on the same boat as you
I think that the magnetic switch is near the home button.
Would it be possible to put a metallic barrier on the back of the tablet between the back flap to prevent the magnet on the front flap triggering the switch?
Metallic Plate Works!
Putting a metallic barrier actually works very well. I got a magnetic phone holder for my car which came with 2 metal plates (with adhesive) that you can stick to your phone back. I didn't need the larger one and tried it with the Tab S2 (9.7) official keyboard cover. And it worked!
The pictures show where exactly is the "sweet spot".
Update: Apparently the position outside the box reverses the effect - switches off when you remove the keyboard. The solution I found is to wedge the metal plate behind the cover just near where the cover snaps to the tablet. Works perfect!
Nougat Updates solves the auto-off bug
The auto-off problem seems to have been solved with the Nougat update. After the update when I connected the keyboard cover, the touchpad was not working. I unpaired and paired the keyboard again. Got both the keyboard and touchpad working. Then discovered that the auto-off bug is also solved when I folded it in reading mode with the keyboard in both on/off positions.