I've been using duttys V4. Then I've upgraded hardspl to 1.93 but from then I can't upgrade anything more. I've downloaded new roms, but upgrade is at 0%. I've even tried original HTC rom but nothing. I am now on hardspl 1.38. What more can I do?
Related
I've been trying to flash the cingular update from htc and when i try, it reboots into the bootloader screen and then on the computer it pops up saying that RUU has stopped working and closes the program.
I am using vista, and I followed the guide from mrvanx on replacing the vista drivers and was able to flash hardspl onto the phone.
I dunno if the hardspl is what is causing the problem or not, but i want to try some custom roms and before i get into those, I want to make sure i can reflash the cingular rom just in case i don't like any of the custom ones.
Thanks for the help
I am having the same problem flashing the official HTC WM6 ROM.
I have Hard SPL V7 and Shapps 4.31 WM6 installed currently and want to go back to the official HTC ROM.
Grateful for help here.
Right, so I have 1.93 HardSPL installed from Olinex, but for some reason I can't update the ROM to the official HTC 2.03 release, it gets to 100% then shows a Upgrade Rom Error, Image File Corrupt, Please Try Again, message on the bootloader, I figured this might be becuase it needs the original 1.93 bootloader with it being a official release (unless I'm wrong) so I have got the stock 1.93 spl from the spl thread, I ran the update, it went straight to 100% and rebooted, still got Olinex's 1.93 on though.
Help.....
I have this problem too Gurus help please!
He-he, the problem is solved. To boot, you need a 1.09.25.23 radio.
I have ha diamond P3700 with the latest stock rom 2.03xxxNOR (norwegian) ,
Together with this upgrade came the SPL 2.03
I have tried a million times to put HardSPL both from Olinex and the 1.24 , The same problem happens all the time. The phone sync with active sync , can flash original HTC rom , but with any of the hardSPL the phone disconnects after turning black and after a few minutes I get the error message 260 , the phone is not connected. The PC cant recognize the USB device before this happenes.
I`ve tried to run SSPL manually, i`ve tried 4 computers and different USB.
For me it seems like the new SPL 2.03 blockes any attempt of putting something non-stock on my phone Anyway to bypass this???
Hello,
When I bought my Diamond I upgraded it from 1.93PTG to 2.03PTG.
Although, I prefer English interface. So, I hard-spl'd it with OliPro's but I still couldn't flash the 2.03 Europe one.
So, after searching, I found a Hard-SPL 1.24 (followed the instructions) and everything went fine...
Maybe you should try this one also...
Hard-SPL post:
http://forum.xda-developers.com/showthread.php?t=408621&highlight=hard+spl
Best regards,
Nuno
I had the stock NOR 2.03 rom too, and flashed with no problems using Olinex unsigned hardspl 1.40.
Using a WM 6.5 ROM atm, and everything works well
Hi,
I sent my diamond back for repairs, and when it came back it came with SPL-2.03
As a result, I can not flash RUU_Signed_1_93OliNex_HSPL_UnsignedEdition which i need to install a cooked rom from here
Anyone have any ideas what I can do?
Thanks!!
you can't flash SPL 1.93???
My Diamond had SPL 2.03 and I managed to flash 1.93, maybe you're just doing something wrong.
I noticed there's a quite a few different new official SPL versions out there..
Can someone tell me if there's a difference in performance/battery life between hard-spl 1.40 & 1.93? I'd really appreciate it.
just run the sspl-manual from your device and try flashing HSPL after your screen becomes blank.
I've recently bought one of this...It came SIM unlocked...
I want to flash a new ROM and HARP-SPL...SU unlock and all the usual stuff I did with the 3 or 4 HTC TOUCH DIAMOND I previously had.
What I'm doing is the same I always do with Diamond, but the MDA does not pass the 0%!
All goes well...the picture with the 0% - 100% board comes up...and when it should be flashing it just stucks in 0%...
The phone is not bricked or anything...
Am I doing anything wrong?
What should I do diferent?
First flash hardspl 1.93 olinex. then flash the rom. That happen to me too. good luck
Could you please link me where I can find that???
Here you go http://forum.xda-developers.com/showthread.php?t=400950
Don't forget choose 1.93 olinex version.
I did not have the same luck!
As soon as the phone shows up the bar of the flashing (the one that shows if its 5% - 10% and so on until 100%)...it freezes at 0% and does not get out of it, until the update process shows an ERROR (262).
All I did was to try to flash the 1.93 olinex you pointed...or is necessary any prior steps?
Problem solved...
It needed, in first place, to have the ORIGINAL unsigned hard-spl from olinex.
THANKS!