Develop Bugs

What the Feezy????!!! JasJar stuck in bootloader mode.

I was trying to upgrade the radio on Universal, somthing I did all the time on my magician. And I think the upgrade worked, I'm not sure. BUt now it won't get out of boot loader mode. If I hard resest and choe clear it says "clearing now" then just goes back to loader mode. I've tried every key combo I know. Power + reset, backlight + power + reset, pulling the battery. Nothing works! Anyone had this issue before? Any suggestions? :?: :?: :?: :?: :?: :?: :!:

That happend to me too. I tryed every thing ... not working ... then i upgrade to the last radio and (soft-reset and power botton) and it worked ... i havent make any upgrade after :lol:

Hi,
the same happened to me, but I solved the problem:
1.) Make the update without any card (SD + SIM) in the phone!
2.) Use the original USB-cable
Now it should work!
Greetings,
Teja

Thanks guys. Pulling out the SIM and the SD did work. I wonder why though? ANyway, thanks again.

A million thanks!!!
I read a lot of replies on other threads, and nothing worked.
Then your suggestion of the Sim + SD worked like a charm.
Thanks a bunch for restoring my expensive brick.

It took a long time for me to find out you've to remove the cards so I was about 2 weeks without my expensive MDA-Pro. And I'm looking forward if it helps anyone to solve the same problem!
Greetings,
Teja
As you've seen, it was my first post here...

Stuck at USB V1.01
New to this. I have a QTEK 9000 Spanish edition. Was upgrading the ROM and the PC for some reason restarted cutting the connection while ROM was in progress. now the PDA is stuck in USB V1.01 screen, tried to hard reset. nothing working. I have read posts about removing SIM and SD cards I have done this. I can not even connect back to the PC, I use the original USB cable, windows pings to suggest a connection is made BUT, now light shows uup on PDA to suggest a connection and Windows mobikle Device Center is not picking up the device. can anyone help me?

Hi, the same problem with me. So at last I am successful and I solve it. I suggest you. First you make update with out any card and then the second step you use the original USB cable.
Try the best.

Bootloader screen stuck!
I dun know i removed cards and hard reset but still its not connecting... show usb when connected to pc and Serial of not down at the bottom show v1.01
Any idea what should i do now?

My grey screen says USB v2.07 I think I killed it!

My grey screen says USB v2.07. I tryed to update the radio to 1.13... I copied the EnterBl.exe over to the Siemens SX66 and executed it. It blinked and then turned off. Then it came back on and displays USB when on the cradel and Serial when removed. I cannot get it to do anything now. Does anyone have any advice?
Thanks,
Bobby
Cingular
Siemens SX 66 ( I have no idea how that translates into blue angel)

same here
if some one has a sulotion please send me instruction or a mail [email protected]
thnx

you are stuck in bootloader mode. just run the setup for rom upgrade/restore for your device and it should work. I think a hard reset will also allow it to reboot into normal mode, but not sure.

Defiant XDA
I cannot seem to get it to reset nor be recognized by the computer when it is placed in the cradle. It will chime as it is placed in the cradle, yet the charging light no longer ignites and the hot-sync program on my WinXP pc does not indicate that they are connected any more.
Thank you for your time!
Bobby

restore the original ROM. I had this issue after I run a defrag on my "Storage" folder using Storage Tools. I could not reset it. Also, upgrade with higher ROM did not work.
You have to restore / setup using original ROM version. Good luck!

Follow this link, download the update and follow through the instructions.
http://t-mobile.iris-global.com/download_manager_mda_3.html

original rom
Does any one has the original rom for the ph20b my son messed it up
\if any one can send it via email or a link will be helpfull
thnx

Another Possible Solution...
This has happened to me numerous times when upgrading to various ROM versions and through experimentation I finally realized that it was related to my storage card. I also remember reading another post like this where this problem can occur if the storage card is on the large side (>= 1GB ).
Just take out the card and reconnect to the cradle and you should be able to flash again.
Hope this helps

Bootloader dead / Recovered

Hi,
I made a mistake with flashing QTEK S200 with wrong file.
Bootloader was modified. Device can not start at all.
It can not even go to bootloader screen (red-green-blue).
As consequence, no USB connection can be established.
What is the solution? I guess utilities can not be used, because they assume connection to USB, but there is no connection.
Not big deal, because it was not working well anyways, but would be interesting to know a solution in this case. Many ppl. would be happy to know how to manage this situation, I guess.
later.

Not very good news, service center said they don't know how to fix it, but kept the device to make few things with it.
Clearly, bootloader was overwritten.
Will see. Somehow they manage to identify type of rom is installed from i-mate.
So, think before you make any flashing
re: another service said they will do whatever needed, up to replacing chip with flash. I am not ready to go that far yet.
feel like i am missing something

It appears to be a real problem with flash.
No connection to computer with USB.
With power supply connected blue-green-?? screen, but I cannot connect to PC of course.
With USB cable connected blue-green-?? screen does not come up.
I figured out that pins 4 and 5 are shorten when power supply is connected. I did this with USB connection to PC, but still not connected.
For sure, USB is not functioning on device.
Will get new device, but very interested on how to repair this one. I disassembled it completely. There is no way to replace the flash chip at home, you need specific equipment and chip, of course.
What I need is surcuit diagram for S200 or similar, particularly part of diagram related to flash, radio module is not needed. Is there any possibility to get it? If I have it, I think can reprogram chip.
Thanks.
Hm. It looks like extreemly difficult to get pins layout on motherboard.
JTAG is the only solution left to access chips direct. But we need to know where JTAG pins on motherboard.

Recovered S200.
Finally very good news!
Prophet S200 was succesfully recovered with help of Arc.
He managed to discover JTAG pins, afterwards re-flashed SPL and ROM.
REALLY GOOD JOB!
Want to say special THANKS to Arc!!!
Device go live again.
Until next experiment....
But procedure to recover is in place.
Regards,
fdp24

i have a dead one too
Hi there,
I have a dead one too can you tell me how to fix it please?

dead, as in my ppc k-jam is dead
basically it hangup and i soft restarted, tried hard reset. it didnt help either. i tried restoring to factory default same thing it hangup. now it doesnt shows any signs of life . i lost my life, my buddy.

My Orange SPV M2000 will not start anymore after update. I only see Serial (on top)............ V2.07 (underneath)
I tried to update my ORANGE SPV M2000 to Tmobile's newest rom by extracting the exe. file and using maUpdateut. It started well and all of a sudden gave error "country code................"

You will not be able to fix it yourself.
Equipment and phone required physically in order to connect jtag interface and re-flash DOC.
Sorry, but this is the only solution if your bootloader is damaged.
Of course, you can try to ship it to service center. If you are lucky they will change your device. This might more simple.
Good luck.

fdp24 said:
You will not be able to fix it yourself.
Equipment and phone required physically in order to connect jtag interface and re-flash DOC.
Sorry, but this is the only solution if your bootloader is damaged.
Of course, you can try to ship it to service center. If you are lucky they will change your device. This might more simple.
Good luck.
Click to expand...
Click to collapse
I know how to open device and solder some wires to testpoints. Do you have any information where the pins are located and what software and what JTAG adapter you used? I really need to get my phone working again. It was quite expensive to purchase and to ship it to my country. Please don't destroy my hope.

hello friends,
my cousin recently buy O2 XDa ( wallaby ) for cheap one, i check on device it seems cann't boot to windows but if i hard reset and came up red, green, blue and if i press ok it came up with test all thing i confuse all the test is OK, can you all tell me how to repair the phone and waht is the problem?
thank you

dead device hope on the horizon
note my device and troubles is on the xda2
hi - i have had exactly the same issue - i have managed to reload the rom i was trying to swop and here is what i did .... it took ages and lots of patience and it is not an exact work of science but if you try my method 2 or three times it actually comes back to life ... honest !!
down load an xda2i ( yes xda2i )rom extract it using winrar or zip on your pc place dead xda2 into cradle regardless of whats on screen run himupgradenoid - the rom will run and start to load onto your device it will fail once it has failed remove xda but do nt reset - take copy of original rom which was on the device prior to your failed upgrade and extract as above. replace xda into cradle might be detected or not dont worry - run the himupgradeut from your previous working rom and wait it takes ages to connect but eventually heypresto ... you will have a working device. i know cos i done it !!! - i have not resolved all my problems yet - i still want to load latest 02 rom but even after entering correct device data into nbfs using batch file method the device crashes saying incorrect counry id. - i accidently created my problems by accidently running the wrong upgrade rom and i guess it changed somthing on my device " country code" however when i use method above to get original rom inplace and working when i extract device data into windows folder on device i still see the wwe ( world wide english) so i am still in a pickle - can anyone help me .

hello
i'm working on the project of flashing the bootloader into a totally erased and dead phone. can you send us the test points from the prophet please? and if you know their location on a WIZARD. thank you..

Somebody here Please tell what soft to use with JTAG to recover da bootloader!!!!!!!!!!!!!

get the JTAG pins for me, I will send you soft.
Wizard and Charmer pins are both needed.

hi, i've succesfully wrecked my Blueangel PH20B by flashing a modded wm6-universal-rom... i've got all the hw & sw to resurrect the phone but the jtag pins on the BA-PCB...
can someone give me a hint where i may find them? (i'm not wanting to bake the pcb as i know i'll wreck it comletley)
thanks in advance,
mario

Same problem here
Hi,
I believe I'm having the same problem
Please help me
Thax a million

so can you help me i need to write the wizard(g4) bootloader or thell me how can i do this

T-Mobile USA SDA II
Me also, i'm i need of re-writing boot-loader of T-Mobile USA SDA II

well, ok I understand that you can get the Jflash_mm working with PXA systems, you can write the definition for yourself, as for the CPU.
but I have serious doubts that inspire me to suggest you will have tiny chance to actually program a DiskOnChip Millennium series (or familiar) chip used in many platforms (actually I believe most HTC devices).
after all this means that if you are not working for (or in affiliation or partnership with) SanDisk, you are not in position to program bootloader to (not limited to) UNIVERSAL, WIZARD, PROPHET, and CHARMER (and if I remember well, BLUEANGEL and HIMALAYA) devices over JTAG.

any news............

Phone can't power on.

I have a o2 xdaIIs, when I connect the battery, the phone goes to boot model, show me the serial and version v2.07, when connect to usb, connect to the computer, try to reflash the rom, no success. Please help me.

what's the error in the computer screen?
it may help if you searched the forum
using the string that is said in the flashing program.
like Error <number>

I too am suffering from the sam problem.
I was attempting to upgrade the ROM and it failed. Now all I see on the XDA IIs screen is USB at the top and v2.7 at the bottom. This is whilst in the sync cradle.
When out, the USB changes to SERIAL.
Please help as I don't really want to use this as a paper weight
Thank you....

"the USB changes to SERIAL."
when it does that it's ready to recieve a new rom and starting the flash will give it that if it finish successfull that is

thanx for that. I also went scouring the forum and came across a faq about this very problem...
thank you though for taking the time to respond.
I appreciate it !
have a good new year !

Aarrgghhh Help Error 260 When Flashing

Help please
i have a t-mobile uk mda compact 3 phone nd im on t-mobile uk tariff, i have downloaded the official t-mobile uk windows mobile 6 rom.
when i atcive sync and go to flash the new rom i get the utility program up, the phone turns different colours ie red, green blue with black strips, the bar then shows on the pda on the pc screen it gets to 3% and bang invaild error 260 and the phone then resets
ive tried it on xp as im on vista same thinf happens, ive tried uspl, no joy can someone tell me how to get thos rom flashed to the phone in vista a easy step by step procedure to follow cause so far ive lost 8 hours since sunday to tonight
please help.............

SD card removed?
remove your SD card

USB board
you may have been not so carefully with the USB connection contact of the phone, or you ahve charged the phone at car while you were starting the car engine..some guys repaired this in service, or it passes by itself.
at me i tried different days and different softs ... and i did i, i got the same error.

fun0815 said:
remove your SD card
Click to expand...
Click to collapse
Hi i have removed SD Card, tried it without, with also with and without sim card still no joy i need step by step help on this

pskint said:
you may have been not so carefully with the USB connection contact of the phone, or you ahve charged the phone at car while you were starting the car engine..some guys repaired this in service, or it passes by itself.
at me i tried different days and different softs ... and i did i, i got the same error.
Click to expand...
Click to collapse
The phone usb connector is fine, i dont charged the phone in a car as i dont own a car
so what is ther soultion there is nothing wrong with the phone or the connector as it connects up via usb and uses active sync also installing other software and transferring pictures, music to and from it also work fine!
i can see both the phones memory and sc card in my computer.
its just this bloody rom file and error 206 that i am still needing someones expert advise and step by step help on

Please Please Please Please Heeellpp Aargggh Part 2
CAN someone please help me out and to whoever has managed to upgrade using vista!!!!!!
please help

After searching this forum, this came up:
http://forum.xda-developers.com/showthread.php?t=312052
Title: USPL - 100% Working in vista
step 7 says:
7. After switching the drivers plug your artemis again and install USPL, there should be no more problems with connection lost (errors 260, 270)​
Suggest you read that thread, hopefully it solves your problem.