Develop Bugs

UNIVERSAL in Boatloader mode not recognized by PC-USB

I tried to upgrade my rom but the process crashed. The utility mtty doesn't work because when I connect the universal, boatloader mode by the cable, to the pc, it says "USB not recognized" (sometimes when I connect the computer is frozen till I disconnect the cable of the universal)
Please, I tried to have some solutions in the forum but all the posts indicates is needed previously the usb connection.
Do you know if should be possible to run the flash of the rom in other way, for example using a serial cable connected into the miniusb of the universal, because the boatloader screen says "Serie, v.1.01"
I apprecite what you can say please, I'm really in a hole.

Try this...
Try taking out the battery for a few minutes (10-30mins) and reboot your PC then repeat upgrade process. Hope that helps. Good luck!!!

I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...

sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
Click to expand...
Click to collapse
In my case it still happening in other computers. Conclussion: some piece of the software in the universal has been lost. The screen shows "Serial" that means on some way that is opened to comunication but not USB.
My questions are:
- should be possible to put some starting software in SD and do the universal boot on it.
- do you know how to connect to the computer COM! port from the usb miniport of the Universal.
I appreciate, I was not planning to replace now the Universal...

beginner said:
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
Now works.... I still thinking windows is so stupid software made for distroy our mind ....
Solved after install drivers for a converter usb -rs232 ( I was looking for the way to connect from rs232 the universal)
I'm happy again and I promise don't try to change rom again (at least for a while)
If some person is interested in what brand of software/hardware I installed, send me a mail...
Thanks hearing me ...
Click to expand...
Click to collapse
Click to expand...
Click to collapse

i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD

zedino said:
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
Click to expand...
Click to collapse
I want to say that is running after doing some things and obviously some of it solved my problems. I made:
- unistall last version of activesync and go back to version 4.0
- delete all the applications using ports usb.
due the connection still not running (windows message: device not recognized) and because in the screen of universal I saw: "COMM1" I tried to connect from computer port rs232. By that I purchased some special cable, name: hama brand, rs232 serial, 9 pin - usb.
As you can imagine all the steps I followed were followed by the typical restart of windows. In this sense is important to say that the universal, after connect, need to do a soft reset each time (again windows....)
Other comment is that I unmark the option to connect by usb in activesync and mark the connection by com1.
and after all was done, connecting by usb the unniversal, kill wcescomm, windows said "NEw usb device, sync device". I started mtty and now appears the USB option, great! same time the screen in universal changed from comm1 to usb, more great....
and that's all.

does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port

zedino said:
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
Click to expand...
Click to collapse
I think my english wording was not fine. I mean I solved my problem after install the sofware -drivers- of the rs232 connector, but connecting to the universal by usb as on standard way I was syncronizing previous the crack with activesync.

OK, where to get this driver?
thanx

?????????? NOTHING ?????????????

zedino said:
OK, where to get this driver?
thanx
Click to expand...
Click to collapse
Try here.
http://www.hama.de/portal/type*3/action*1026/searchMode*1/q*039703

I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.

shrubbery said:
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
Click to expand...
Click to collapse
not works, probably is this device lost forever, i have restarted device and PC almost hundred times, still the same result, uni stuck in Bootloader screen top of page "Serial" bottom of page "v1.00"
nothing changed, even if i connect to USB port
if someone have some solution to this s*it pls let me know
thanx

i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck

mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
no, my problem persist, hundred times i tried to recover friends device using upgrade by original shipped ROM but the device is not recognized by system so there is allways connection error, so this kind of reliving this UNI is not usable
anyway, thanx for raply and suggestion
ZeD

mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
If you're stuck in bootloader mode only, visit www.buzzdev.netand look for ExitBootloader utility written by the great Buzz. Just follow his instructions or scroll thru' Universal's forum here and there for problems relating to "stuck in bootloader"
hope this helps

no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD

i had the same problem with the QTEK of my principal after I upgraded his ROMs.
(after the hard reset, the pocket remained in bootloader mode).
you can solve this problem in a very simple way:
you have to launch the bootloader installation (BL1.01_RUU_UNI_V.1.2.EXE) from the PC (still connected with the PPC through USB) while the PPC is in bootloader mode (on your display you see "USB > Serial 1.01" or something like that).
then you do a SOFT reset and the pocket boot normally.
very simple.
i hope to be helpful to someone.

zedino said:
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
Click to expand...
Click to collapse
I had some problem. After uninstall all usb applications in the pc and install the software for cable usb -rs 232, doing some softreset in the pda connected, it turned the screen message "Com" by "Usb"

USB Device Not Recognised on Bootloader

I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.

Try this it shld work
hdubli said:
This is based on my experience with two UNis..one Exec and other JASJAR..both had same problem...this is how I solved :
-Put yr device in bootloader Mode
-Disable USB in Active Sync
-Now connect woth USB cable and open mtty utility
-Select the "WESUSB... " port
-You shall see a blank white screen..press Enter to get "USB>"
-Then type ( as BUzz has informed) set 14 0
(here I wud like to inform that after doing the above I did not get success so I typed set 14 10,then set 14 9 for two three times)
-Then I ran the ROM Upgrade directly(After enbabling the USB)
-I then followed the procedure as informed on the COngratulations Screen that is hold the two "-" buttons and soft reset and then pressed 0
-I got them back to normal..
I hope this helps to all my friends...Pls feel free..pls do not trouble our Buzz..he might be busy in inventing something more to our devices
Click to expand...
Click to collapse

Guru Meditation said:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Just noticed your user name, I was a big Amiga fan a few years back, still fire up Amiga forever occasionally on my PC when I feel the need.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Click to expand...
Click to collapse
Try it with a different USB cable or in a different USB port (don't go through a hub and if you've been using a laptop then try it on a desktop PC since some laptops have hubs built into them). If that doesn't work then you're out of luck as your Universal isn't detecting that you've connected to your PC and its time to send it in for repair.

Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?

i am stuck on the same problem and wondering the forum for almost 3 days now with no luck.... please help my device is in boot loader mood but not turning the serial to USB ......... please HELP.......

solution
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Please follow the steps:
1. Plug in ur usb cable in bootloader mode while it is showing 'serial' and version 'x.xx'.
2. Soft reset by pressing Backlight+power+reset pin WHILE KEEPING THE USB CABLE CONNECTED
3. your phone will now reboot into 'usb' mode. Don't remove the usb cable yet.
4. Remove the Memory card while keeping the usb cable still connected and VOILA,your pc starts recognising your phone as Microsoft usb sync.
5. Do whatever you want to do now (upgrade)
Hope it solves the problem now.
Press thanks if it does.

Something else to try
Having had a few issues with my G3 Uni, I've been through my fare share of Uni bootloader issues. When I find that I can't get the 'serial' to go to 'USB', I normally find it's because I haven't taken the memory card or the SIM card out (usually the memory card).
Make sure your memory card is out, then try to enter the bootloader and see if this cures it. If it does, then use mtty and the command 'set 14 0'
This tells it to reboot on reset. if you were to use 'set 14 1' it would go back to the bootloader on reset.

my Htc hd2 t-mobile won't recognize usb on boot-loader mode
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!

kaleb2954 said:
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
Click to expand...
Click to collapse
you have the wrong forum friends! This Htc Universal section
to update Android on HTC HD2, you can use the Clock Work Mod Recovery !! for more details should refer to this thread http://forum.xda-developers.com/showthread.php?t=1021837

I-MATE JASJAR hung
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me

bechir2013 said:
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
the first point...

A lot easier than to root this device

Stucked to "Serial" bootloader mode

Hi all,
I was trying to upgrade my Qtek9000 with an official ROM Updater, but my device went immediately into the Serial bootloader mode and I've not been able to do nothing to run out from this mode...
I've tryied the solutions suggested in http://forum.xda-developers.com/showthread.php?t=290234 without any luck...
The problem is that neither Mtty nor the UNI_exitbootloader tool are able to connect to USB.
I'm using no usb hub, I'm running on a Dell Precision M90 notebook, I've disabled USB connection in Activesync (4.2.0) and also tryied with a pc without activesync installed.
Any idea?
Thanks
Paolo

Are you on XP or Vista, and what version of AS/WMDC do you have?

Hi,
I'm running Xp, ActveSync is 4.2.0, don't know what WMDC is sorry, can you please explain?

Don't worry about WMDC - it's only relevant if you have Vista.
Are you using the proper cable that came with the Universal? Some cables don't have all the pins wired. That (or a broken USB port) would explain why your Universal isn't going to USB mode when you plug in the USB cable. Have you looked carefully to see if it changes from saying "Serial" to "USB" at the top of the Bootloader screen when you plug in the cable?
If it does change to "USB", I would try upgrading to ActiveSync 4.5 - go to http://www.microsoft.com/windowsmobile/activesync/activesync45.mspx
Make sure you disable USB Connnections in the Connection settings before plugging in your Universal. Then try flashing the CE ROM again.
Good luck
BTW did you try doing a hard reset to get out of bootloader (both soft keys and then the reset button, then select 0).

Good advice, especially with upgrading to AS 4.5, it's a full release now on Microsoft Update site, and I have a feeling the WM6 ROMs may require it... Good luck with it, keep us posted.

Ok, thanks all!
This morning I connected the PDA to my office's PC with it's original cable and it instantly switched to USB mode...
So, I launched the upgrade and it's now in progress... let's hope!!!
It might really be a cable problem, yesterday night I tried with 2 different PC and a not original cable (I think it's my camera one...)
Thanks a lot, by now... I'll let you know own this story will end...

Ok, new ROM is up and running!
Thanks all!
Bye
Paolo

Good stuff.

HELP! ROM flashing related issue? On Activesync: USB Device not recognized???!!!

Hi, I have reflashed my ROM I dont know how many times. Yesterday I tried to connect via activesync on a new ROM and it wouldnt connect. These are some of the things that happened:
Device orange charging light flashes a few times then goes off [never seen THAT before]
Activesyc menu comes up on device but activesync doesnt connect
Get 'this device can perform faster' message on desktop
Sometimes get USB devce not recognized on desktop
SOmetimes device orange charging light it stays on if I plug direct into PC but still doesnt activesync
I have tried to connect as DISK DRIVE but I dont see the device on my PC.
Have tried different ROMS, 6.5, 6.51, sense 2.1 and 2.5 but all have same issue. Have also tried connecting to other computers. same issue.
Have played around with USB to PC menu options (enable / diable faster data sync etc) but doesnt make a difference.
Anyone had this problems? Thoughts?

Have you tried diselecting "ask me 1st about usb connection type when I connect the device to the pc" under USB to PC settings
It worked for me

This is the exact problem I am facing!
I tried everything - as diskdrive, activesync (with/without speedup), etc.
On many ROMs, even the original one (WM6.1)
Can't connect - every PC gives an 'unknown device' and on some ROMs I cannot charge via USB, only via mains...
I also tried without the question on connection.
Just some thoughts:
Do you have corruptions on screen sometimes? (Some graphical glitches)
Any .CAB files you cannot install?
Did you try to reflash the same ROM more than once?
tried to connect without card in the device and in flight mode? (Uses less power)
With me it started after a ROM flash from Miri... (I don't blame him!!)
The Hard SPL did not give me any problem, the radio was not flashed, just the OS. But reverting did not help.
I certainly hope you will find a solution, since I have the exact same problem!!

Do you stil know what ROM you flashed when this problem occured?
I reverted to original ROM 6.1 AND 6.5 which included everything - boot, radio, os, stardup image. But it did not change!

I figured it out after trying everything i could: i think its a hardware problem. I have dropped my devicetoo many times, or plugged it in too many times. Who knows.

ekerbuddyeker said:
I figured it out after trying everything i could: i think its a hardware problem. I have dropped my devicetoo many times, or plugged it in too many times. Who knows.
Click to expand...
Click to collapse
And how did you figured it out? Did you return the device to the shop?

I have this exact same issue except I am on AthineOS... I thought it was my PC until I read these posts. No OS updates or any other machine updates were performed except on my device. Any clues as to a fix?

Somehow I don't think this is just hardware.
I did drop my device once, but that was even before first flash. After that it still worked.
So, some weeks later I HSPLed without any problem. After that the device still worked.
Then, after investigating which ROM to use I flashed the ROM a few days later.
Right after the first flash it all still worked. So, had to flash another and from that moment on the device cannot be reckognised by any PC.
I still think it has something to do with the flashing. I think the device does not give correct feedback when it receives some commands from PC (eg. the command to reply the device type/number)
Does anyone know a program which can check the USB port for the HTC Touch Pro 2? Just to test wheather the connector pins are ok?

download activesync 4.5 and run the setup. it will perform a repair. that usually solves the problem. if not, try a different usb cable and try plugging into different ports on your pc.

crazythunder said:
download activesync 4.5 and run the setup. it will perform a repair. that usually solves the problem. if not, try a different usb cable and try plugging into different ports on your pc.
Click to expand...
Click to collapse
These are the first things done. And this was already written in here.
It happens with many PCs, including some on which the device never connected to.
Also tried different cables, ports, etc.
Also disabled the fast transfer etc. etc.
Even tried several other ROMs, inclusding original Dutch 6.1 and Dutch 6.5

I'm having the same issue. I can connect via bluetooth, but not usb. And I'm stuck with 6.1. I was tole my phone was brand new, but now I'm starting to think otherwise.

waynehead05 said:
I'm having the same issue. I can connect via bluetooth, but not usb. And I'm stuck with 6.1. I was tole my phone was brand new, but now I'm starting to think otherwise.
Click to expand...
Click to collapse
Some questions, to verify this is due to flashing or is a fault in the design of the device...
- Where did you get the device?
- Have you flashed the device?
- Did you accidentally drop the device?

hi just to say had a completely orignal o2 xda orbit 1 flashed with new rom everything worked perfect before now active sync plays up i can sometimes connect but get usb device not reconigsed then click cross then pull out usb then reinsert then active sync connects works fully functional then after 5 min it disconects this is driving me mad as use active sync for a fast internet connection on my pda as my wifi is crap

P3300 can't connect with USB

Hi guys, sorry for my bad english.
Since today can't sinchronize my ppc with wm 5.0.
Here's the problem: when I pug it with usb cable, nothing happens.The orange light is on, the phone is in charge but nothing happens.Usually when I connect the phone I can see windows looking for ip address, and the activesynch shows... but this is not going to happening anymore.
I tried to reistall activesinch, I've cleaned the registry and i tried to connect it with others software.Still nothing.
Firewall is disabled.Any solutions?
Thank you in advance.

Zealot87 said:
Here's the problem: when I pug it with usb cable, nothing happens.The orange light is on, the phone is in charge but nothing happens.Usually when I connect the phone I can see windows looking for ip address, and the activesynch shows... but this is not going to happening anymore.
Click to expand...
Click to collapse
I had the same problem sometime ago. I've changed the wire first but nothing happened. My speaker, my Mic was dead and I could switch on FMRadio without the Hands-free!!!
What I did...??? I updated my mobile's Radio with 3.39.90 Version. How can you do this without active sync???
1. Remove SIM Card and Storage Card from the Mobile.
2. Press and Hold the Right Button (Recording Button) and Press together the Power Button. You will be in the Bootloader Screen. Try to update the Radio first.
3. Check it if it's working ok.
2nd way...
1. Copy the official ROM of WindowsMobile to the Storage Card.
2. Press Right Button (you know the Voice Rec) and holding that press the Power Button...
the mobile will be bootloader mode and will try to install the official ROM from the Storage Card...
wait a bit and then when it finish, check it if it is working properly!
Hope to help... waiting to "hear" sorry, to read good news

I have the same problem i cant sincronize the pda whith the activesync and i wish to change the rom. Now it's in france and i wish to change it to english, and it's locked to orange france i think. What can i make? It starts in bootloader, but the instalation from the card is not starting. thankx
le. and if i want to install something gives error 260

I had the same problem 1 month back, checked the mini usb data cable with a multimeter just to find that one of the data TX/RX wire was short with +5v wire, cable was faulty. the 1st and the last wires (+5v , -5v) were ok thats why it was charging the phone, but not connecting to pc, it was giving error unrecognised usb device.
u can also check for bent contacts at the USB mini connector on ur phone.

strange
hy guys
i´ve got a strange problem with my arte110.
for some reason i cant establish an activesync-connection,a few days ago i had some wm6.5 rom running and couldnt connect my device, then suddenly today (maybe because i reinstalled windows on my computer yesterday, i dont know) i was able to connect the phone while in bootloader... so i flashed happy and lucky the original wm (os 5.2.1620 build 18125.0.4.2) rom i got from t-mobile austria.
now its the same problem as before, i cant connect my device, i've restartet artemis and my computer several times, i've reinstalled activesync 4.5 a million times, i've tried all available usb-ports- different usb cables (same cable works with external harddrives) and even my office-computer, and so on...
my pda is (and was allways) charging but i cant syncronize.
has anyone any idea what could cause this problem?- please don't tell me the usb port of the pda is damaged, I wouldn't want to have to fix anything in this case...
hoping for good news, McPerfuntory
[by the way, please dont judge me for spelling mistakes, i'm from austria!!!]

done
okay guys, no need to respond anymore, i got it right..
but i don't really know how i repaired that one, i disassembled the devive cleaned everthing in there and cleaned the usb connector..
..works again