Related
Hi all,
I need to know if someone can help me to bring to life again my lovely JasJam,that was working great until this morning.
The problem is this one:
I was going outside the country this morning (I am in Czech rep. now and I went to Slovakia) and on the way back I realize that my hermes (herm100,spl2.10 olipro,RADIO 1.57,schaps 3.54bITA) was without any signal. I tried an other SIM card and the result was the same.
Once at home, I tried to reinstall schaps,everything was ok,except the signal still missing.At this point,I tried to reinstall the Radio and the bar was still at 0% and after 3 minutes it gave me error 262 and now is with the screen always on (illuminated) on the KITL page and it doesn't start anymore...
please,someone with a good heart,help me.
http://forum.xda-developers.com/showthread.php?t=286755
back a live any hermes ( that's as worked whith my hems)
I don't know that's work but try install any official rom from HTC that's have radio information and then you can install any other. but extrat the signedruu. (that's the rom file) and then put the file into a sd card start your herm by pressing simultaneous the power, and ok button and prissing the reset hole whith the stylus pen and follow the steps it's very easy.
thank you Zefo,
but I am Stuck on the bootloader page, I cannot insert a original Rom because ActiveSync doesn't recognize the phone.
Being in the Bootloader page is fine. Just run the RUU Wrapper, it will connect.
What caused the problem? I am a little worried as I am going to Tenerife on Friday and I am running Radio 1.54.07.00 as well (I assume thats what you meant when you said 1.57)...
Is there any reports of going abroad messing up your phone when its been modified with new radio/rom?
Hi Allan,
I would like to run RUU,but ActiveSync doesn't connect my phone,so when I launch it,they don't communicate. The computer see the device,but ActiveSync not, infact, If I try it,Itgive me error 260 Update Error (I used Hard SPL v7)
Stick what you need to flash on a MicroSD card and stick it in the phone, you should be able to boot off of that.
Theres instructions somewhere in the forum on it all.
I got the axact parameters of yours Hermes, STARFURY, it changes only the rom (mine is/was schaps 3.54b).
I am not able to find what you suggest me but I cannot go on the SD if the phone doesn't turn on the OS...How can I do?
Get a usb cardreader plug your microsd card into an sd card adaptor, then plug that into the cardreader and the cardreader into hte PC. Transfer the stuff onto the microsd card and stick it in the phone,.
but I have just to put the 2 files RUU Wrapper (Bootloader) on it in the main root??and how can I make them start?
I was able to go into the OS but I am still with no GSM and if I try to update it,it stops at 12% also with original ROM.
Can anyone give me a link where can I see where the radio chip is located on the mainboard please?
I'm running Vista and when I wanted to run the bootloader upgrade on my Dash I kept getting this message error. Error 260. anybody find any way around it? I've tried to manually set th ephone into bootloader mode, same result. help!! PS the error is supposed to mean "port already open" or "open port error" I'd really appreciate any help!
erro 260 - fixed
switches to my wife's laptop that had XP on and it worked like a charm. I'd be glad to assist anybody in the process od de-branding their Dash. Removing the ugly T-mobile paint logo on the unit was easy too.
ERROR 260
Sorry for thislong story....
OK, I've been on looking around the site for a while. I installed the WM6 Beta. I was looking for two days for the WM5 ROM only because I want the little things to work. Finally found it. But now every time I try to flash my phone ack to WM5 bI keep getting the 260 connection error. The readme only says to restart the comp and phone and try again. I have literally, no joke, done this 12 times in the last 2 hours, hoping maybe it will go. All the phone does is go to the green, blue, and red screen and stays there. Then the comp says it gets the error. I know it's connected because Sync Center syncs, I can look through the phone, install apps from my comp, etc. Also I tried doing the 'Update only' rom for version 1.11 or so, and it starts to go but then says its the wrong version RUU. Has anyone had this problem before? Flashing to WM6 did this once and then worked after.
I'm running Vista Premium, stock sync cable, Microsoft Sync Center for vista. All this is the sameas when I flashed to WM6.
There goes another 3 attempts, trying to change timing, reinstalling Sync Center, etc.
Decided to try it on my XP desktop, and for some reason, first time it worked. Maybe Vista didn't like it? Who knows..
Mladito Vista!!
Hi there,
I have the same little problem here!!!! I have a laptop with Vista (garbage)... so i´ll try on a laptop running XP...thank you for posting this, it was a big help..i let you know how it turns out... see you around
WM5 to WM6 --> Problems at 3%
Hi all,
I've errors upgrading my phone to WM6.
I Can open the Wizard (it`s a generic to S620/S621), but in 3% i`ve an error.
I think thats my phone has a blocked CID.
How can i unlock this? i`ve tryed with tools to unlock, but without success...
Regards,
Emerson
Hello,
Welcome to the forum.
Your problem is that your phone is CID-Locked. Hence, you'd need to use a paid service to unlock it. I personally used the following service which provides instant unlocking:
http://www.gsmliberty.net/shop/htc-excalibur-instant-remote-unlock-p-1452.html
I used a credit card, it's 39.99 $ - I was done unlocking and upgrading to Windows Mobile 6 in about 15-20 minutes.
Good Luck !
P.S:
Steps to install WM6
- First CID/SIM Unlock using GSM Liberty
- Flash Bootloader
- Install WM6 ROM (It will take some time for it to load so give it about 5-10 mins. it does get stuck at the boot screen for sometime but eventually it'll load)
- Install Office/Audio Manager
- Application Unlock your phone using SDA Application Unlocker
- Install the necessary software/tweak/hacks
there you go, if you have any questions, feel free to ask. also, if you use the search function, everything's available here.
Good Luck !
Here's the following links you require
1) Flash Bootloader
ftp://xda:[email protected]
2)here's the WM6 ROM:
http://files-upload.com/files/472108....90_Ship.ex e
here's office for those who want it:
http://rapidshare.com/files/31706137/Office.WM6.zip
here's Htc Audio Manager for those who want it:
http://forum.xda-developers.com/atta...1&d=1183909664
Ps. I better like German flash, it's smaller due to fewer language packs, and contains English, here: http://files-upload.com/files/472422....90_Ship.exe
thanks to jsp_m for the links.
Hi,
I`ve problems because my IMEI is from Brazil...
And in the site accept only 15 digits IMEI..
My imei is: 35*************02 (17 Digits IMEI)
Thanks,
Emerson
hey,
that's not a problem. everyone has 17 digits, don't include the last 2 digits when you type in your IMEI so for example
11111111111111102
just include the first 15 and submit and you'll get an unlock link in your e-mail, follow that link, scroll down to the page to download dashunlock software and download the .UNL file for your IMEI and then make sure ur phone is connected to active sync and it's green, open the dash-unlock program and then hit enter then it'll ask for the .UNL file, locate it and open it and your good to go - your phone will be unlocked then soft reset it or i think it's automatic and everything's set.
good luck !
p.s: in other words, don't include 02 when you type in your IMEI.
HTC Audio Manager
http://forum.xda-developers.com/showpost.php?p=1355010&postcount=5
Thanks!
I'll Try NOW and let all know...
Regards,
Emerson
Arrghhh!!
My phone still give the message:
Invalid Model ID [244]....
And now? i`ve payed 40 bucks for an unlock software....
Thanks,
Regards,
tatarezende said:
Arrghhh!!
My phone still give the message:
Invalid Model ID [244]....
And now? i`ve payed 40 bucks for an unlock software....
Thanks,
Regards,
Click to expand...
Click to collapse
Emerson;
Read the second post from luckybandit on this thread. That´s exactly what to do to get rid of the "invalid model" issue. Download the bootloader, flash the phone, flash the new ROM and be patient.
My excalibur is also from South America, and worked OK. If you have any doubt just let it know to this thread.
Boa sorte!
Hi,
I`ve problems with the link of Boot loader....
Anyone can send the full URL?
Thanks,
Regards,
Emerson
Hello,
I'm sorry about the links not working, here - i've attached the bootloader for you. here's what you do
1) Run bootloader (attached file)
2) Run the WM6 WWE ROM
3) Run SDA Application Unlock
4) Install Office/Microsoft Voice Command/HTC Audio Manager
5) Install Tweaks/Hacks
here's a site that has some applications and tweaks:
http://mobile.surrealnetworks.com/DashApps.htm
and search this forum, there's tons of information, hacks - etc.
Good Luck !
oh by the way, did you unlock your phone properly?
1) Download unlock software
2) Download .UNL file specifically for your IMEI
3) Connect phone to computer and make sure the activesync's icon has turned green
4) Run unlock software
5) When unlock software asks for .UNL file, browse for it, choose it
6) That's it ! It should say Unlocking done and it'll reboot
Your phone is now Sim & Cid Unlocked. If you have more questions, feel free to ask. just do what i said first then post.
Good Luck ! Hope to see everything working for u...
Hi again...
Now i`ve the Error 260 message everytime my phone boots in "Flash mode" (3 color screen)....
Follow my configuration in this screen:
Excalibur Wi-Fi RUU
ONBL 1.15.0000
Excalibur
SPL 1.15.0000
Excalibur IU
ERROR [260] - No connection
tatarezende said:
Hi again...
Now i`ve the Error 260 message everytime my phone boots in "Flash mode" (3 color screen)....
Follow my configuration in this screen:
Excalibur Wi-Fi RUU
ONBL 1.15.0000
Excalibur
SPL 1.15.0000
Excalibur IU
ERROR [260] - No connection
Click to expand...
Click to collapse
Hi,
Are you using Windows Xp? Cause I've gotten that error a couple of times too but it was in Vista. Try Xp if you're using Vista.
Hi!!
DONE with XP.... but now i`m affraid!! The "Green Screen" with nem OS apparently locked... this is normal? at least 3/4 minutos in the same screen.. both "patches" are applyed sucefully....
Is there anything else to do now?
Hello,
I am new to this forum, and I have read through a lot of the links and threads about this, but I have not found the answer to my question. Will these ROM Updates work on a HTC S621 that I have through Unicel? The phone is unlocked, but I dont know if that means that I still have to download the file that will unlock my phone? I am very interested and eager to upgrade my pnone to Windows Mobile 6.1, but I am honestly afraid that my inexperience with doing something of this nature will "brick" my phone and I will be without a phone. It irrates me to no end that neither HTC or Unicel are going to bother to come out with an official update for this phone, so if I want the lastest update to the phone, I have to go through unofficial channels. Could someone please tell me if this will even work for my phone before I try to do it? Thank you
Larry
Yes it will work sir, just follow the tutorial and upgrade... The tutorial is linked below in my signature... Also, as a beginner I would recommend using Ricky's rom version 24. ... if you need any help let me know okay... also, make sure you run connection setup after the upgrade...
Am I going to have a problem, or should I do something different since the instructions seem to be written for a phone on T-Mobile? I am really fretting about bricking my phone and I dont know if Unicel will do anything for me if I happen to brick the phone because I did something wrong. I would really like to try flashing the ROM on the phone to Windows Mobile 6.1, but I am just nervous, I guess. Thanks for the help and wish me luck
Larry
You should be fine if you read it over (print it out) and can follow directions. The main problems people run into are keyboard layouts and 270 errors.
No Guts No Glory
pfunkside said:
You should be fine if you read it over (print it out) and can follow directions. The main problems people run into are keyboard layouts and 270 errors.
No Guts No Glory
Click to expand...
Click to collapse
Yah exactly just read and follow instructions word for word...
nobody on this site can promise that nothing will go wrong, but it is usually determine that when something does go wrong, it is because the instructions were not being followed.
you sound a little too nervous to me to be trying this, you may want to either find someone else to do this for you, or take a deep breath, have a beer, and then dive in.
i've done this three times without an issues.
I did it to my unicel S621, and works wonderful! pm me if you need the internet settings after...
He will definitely need the internet settings... for sure...
yes, I need the internet settings please. also, how do I get rid of the "fav5" thing off the phone?
Thanks
Larry
larry.twichell said:
yes, I need the internet settings please. also, how do I get rid of the "fav5" thing off the phone?
Thanks
Larry
Click to expand...
Click to collapse
which version are you using? which rom version (i.e. are you using Rickys or Kavana's)
If you are using Ricky's go all the way down to the last thing on the homescreen which should be settings... and then scroll to the right to Chome settings and then in there you can unclick everything you do not like... everything that is bolded will show up on your homescreenv and everything not bolded will not show up..... then restart your phone and you should be on the go...
Hello,
Okay, I have successfully installed "Ricky's" ROM. I followed the steps to the letter in the newbie thread. I installed the keymapping .CAB file. My phone needs the Unicel Internet settings. I have once before reset my phone back to factory specs, which required that I have to go into the local Unicel store and get the internet settings and install them, the problem now is that I could use Wi-Fi to access the internet before with my phone, even though I couldnt through my data plan/cell service. Since I updated the ROM, I cannot even access the new through Wi-Fi. In the instructions, it states that you should run the connection wizard, but the problem is it only lists T-Mobile, AT&T, and Carolina in my phone, not Unicel. I know that the GSM partner of Unicel was bought by AT&T, but I dont want to set my phone to that because I dont know if it will screw everything up if I do.
So what advice can you offer me? Will getting the Internet Settings from Unicel or member Outragis solve all of my problems? Thank you for any suggestions! By the way, I Love the new Windows Mobile 6.1, now I just have to learn how to use it!
Thank You,
Larry
larry.twichell said:
Hello,
Okay, I have successfully installed "Ricky's" ROM. I followed the steps to the letter in the newbie thread. I installed the keymapping .CAB file. My phone needs the Unicel Internet settings. I have once before reset my phone back to factory specs, which required that I have to go into the local Unicel store and get the internet settings and install them, the problem now is that I could use Wi-Fi to access the internet before with my phone, even though I couldnt through my data plan/cell service. Since I updated the ROM, I cannot even access the new through Wi-Fi. In the instructions, it states that you should run the connection wizard, but the problem is it only lists T-Mobile, AT&T, and Carolina in my phone, not Unicel. I know that the GSM partner of Unicel was bought by AT&T, but I dont want to set my phone to that because I dont know if it will screw everything up if I do.
So what advice can you offer me? Will getting the Internet Settings from Unicel or member Outragis solve all of my problems? Thank you for any suggestions! By the way, I Love the new Windows Mobile 6.1, now I just have to learn how to use it!
Thank You,
Larry
Click to expand...
Click to collapse
Yes just private message that guy that said has the Unicell internet settings as you will need them in there and especially for receiving MMS (picture messages)... so just ask him to give them to you and I bet he will be more than happy to provide you with them.
I did PM him, I hope to hear back from him soon. I Imagine I would need to use Active Sync at home to download the updates to my phone.
Thanks for the help and advice, I am really liking the new interface!
Larry
I need Help!
Okay, so I am trying to find the files I need so that my HTC S621 that I have through Unicel to work and connect to the internet. I have contacted Unicel and they sent me a link to a file, and this is supposed to work, but it doesnt.
Here is the email:
Subject: Doing a Hard reset on the HTC621 will remove all Unicel settings
Issue/ Findings:
After doing a hard reset on the HTC S621 you will no longer have any Unicel settings and will need to reinstall them for WAP and MMS. To hard reset the HTC S621 (with the HTC S621 powered OFF) press and hold the 2 soft keys and than press the power button. Do not let go of the soft keys until you see the message to reset your HTC by pressing the send button.
Resolution:
The setting can be reinstalled into the HTC S621 by using a CAB file and a Micro SD card. The File has been posted on the internet and can be installed 2 ways.
Option 1: Active sync
From your PC go to http://www.unicel.com/devices/htsc621.html and download the zip file to your PC. Open the zip file and extract all the files within to your PC. Once this is done you should see the folder 2577 on your PC. Now connect your HTC S621 to your PC (you will need ActiveSync for this part and a memory card) and open Explore. Open “My windows mobile-based device”. Now drag or copy and paste folder 2577 from your PC to “Storage Card”. Once this is complete, unplug your device from your PC and power-cycle your device. After waiting a few seconds, you will get a prompt to do an auto-configure, press yes and your files will be installed. Once the auto-configure is complete, you will be asked to do a restart. Press yes to restart and all the settings the device had at the time of purchase should now be on the device.
After the device has power cycled, a change needs to be made to the GPRS Authentication to ensure connectivity. Please follow the steps below:
Start
Settings
Connections
GPRS
Unicel Info2Go
scroll to authentication type
CHAP
Done
End
Option 2: SD card reader
From your PC go to http://www.unicel.com/devices/htsc621.html and download the zip file to your PC. Open the zip file and extract all the files within to your PC. Once this is done you should now see the folder 2577on your PC. Now open your SD reader, with your memory card installed in the reader, drag the entire 2577 folder to the SD card. Once this action is complete, install the SD card into the S621 and turn on the device. After waiting a few seconds, you will get a prompt to do an auto-configure, press yes and your files will be installed. Once the auto-configure is complete, you will be asked to do a restart. Press yes to restart and all the settings the device had at the time of purchase should now be on the device.
After the device has power cycled, a change needs to be made to the GPRS Authentication to ensure connectivity. Please follow the steps below:
Start
Settings
Connections
GPRS
Unicel Info2Go
scroll to authentication type
CHAP
Done
End
Okay, so I downloaded the file and did what it said, but it is not auto running the file and doing anything. Is this because I upgraded the ROM and the file will not work with Windows Mobile 6.1? I am getting a little flustered and I love the new OS, but I would like to be able to use the internet on the phone. I cant even connect to the internet through Wi-Fi.
Does someone have the correct setting file for a Unicel HTC S621 that I could have to get my phone working right? I would appreciate it!
Thank You
Larry
Couldn't you just add them manually
Start - settings - then each add settings...
I'm surprised Unicel doesn't make them easier to access
This link might help but your easiest bet is getting the guy who commented to read you his.
http://www.howardforums.com/showthread.php?threadid=655672
Running out of memory?
I recently did the Kavana 6.1 upgrade on my Unicel/AT&T HTC S621. Everything is working fine except that the phone is constantly running out of memory (Which, actually, is not really fine...) Using the Free Memory app doesn't really work, as it will free only a KB or so, and it doesn't show the correct amount of RAM, in any case (usually around 5K instead of the 64K actually ob board). Any ideas?
Oh yes, and also, the phone now calls itself a C720W, which is a Dopod (Asian carrier) version of the S621... Anyone else?
Thanks,
John
Everything you ever needed to know about "unbricking" your Excalibur but were afraid to ask is in this guide. I've put together this guide for those of you who either intentionally or unintentionally "bricked" or think you've "bricked" your Excalibur.
It is not easy to brick an Excalibur if you actually read and follow all of the steps and guidelines before a flash. In fact, not many things can go wrong unless a USB cables disconnects during a flash, your PC crashes in the middle of a flash, or you flash a corrupt image file to your device. Statistically, most of the time people only think their Excalibur is "bricked" when actually it's not.
There are three methods you can use depending of the severity of the "bricking". The first method will unbrick 50% of all Excalibur's that have simply "locked up" and won't reboot properly. The second method will unbrick 95% of all Excalibur's that encountered flashing problems or flash failures. The third and final method, and the most involved, is a "last resort" for those who have tried method's one and two numerous times unsuccessfully.
** Please perform these steps and methods at your own risk. I am not responsible for any damage you cause your device using this guide.
If you're new to the Excalibur or SmartPhones in general, please take the time to read the WiKi and this post by Stylez for valuable info before you post or try any of these steps.
http://forum.xda-developers.com/showthread.php?t=397583
http://forum.xda-developers.com/showthread.php?t=537151
But, before I even get into unbricking, if your phone is in fact working right now, I highly recommend you flash HardSPL to avoid even having to follow these steps anytime in the future. The steps and info for HardSPL and JumpSPL can be found in this thread by jockyw2001:
http://forum.xda-developers.com/showthread.php?t=329605
HardSPL basically flashes your phone with an "unlocked" security partition so all security checks are bypassed when you try to flash a cooked ROM or a ROM designed for another variation of the Excalibur such as Dopod, HTC, TMO Dash, etc. Makes life much easier when trying different ROMS or cooking and testing your own! Thanks jockyw2001!!
Ok, so onto the fun stuff... Your phone won't boot... Either it's locked up and simply stopped booting or you flashed your phone and it won't boot. What do you do??
Method 1: Assuming you didn't get "bricked" from a flash problem, the first and easiest method for "unbricking" your Excalibur is (this will erase ALL data in your Excalibur):
(This method works for 50% of supposedly "bricked" Excaliburs)
Remove your SIM and SD card
Remove and reinsert your battery
While holding the two softkeys with your thumbs, press the power button
Continue holding the softkeys until a black screen appears saying "This operation will delete all your..."
Press "'send"' to restore to hard reset your phone
Let the phone cold boot and restore
That didn't work!! . This next method will reflash your phone to the factory ROM.
Method 2: Second way to the path of unbricking is:
(This method will unbrick 95% of all Excaliburs)
Get a hold of your Shipped ROM. You can find these ROMS either in Dopod's site, HTC's site (with a valid serial #), TMO's site (http://www.t-mobile.com/wmupgrade/ with a valid IMEI), or right here at XDA at this post (http://forum.xda-developers.com/showthread.php?t=381726)
Download one of these factory ROMS and unpack it. **Remember, if your phone is a TMO Dash, you MUST use a TMO Dash ROM. If your phone is HTC Branded, you MUST use an HTC ROM, etc., etc., etc...
Remove the SD card if one is inserted in the phone
Remove the battery from your phone for a few seconds. I found this step to be essential to reset the device. Put the battery back in.
While holding the camera button on the right side, press the power button. The phone will enter "bootloader" mode and you will see a tricolor bootscreen.
While in this mode, plug in your USB cable and you will hear the "ba-bing" USB sounds as the device connects
Unpack the ROM package you just downloaded and run RomUpdateUtility.exe. Follow the steps, check the appropriate boxes, and start the flash
Assuming all goes well, your phone will flash to the factory ROM and you can then troubleshoot what went wrong the first time that bricked your phone.
Oh no!! That still didn't work!? Or it worked but the flash failed with Error 270 or another error......... Never fear!! XDA-Developers is here! This next method is a bit more intense. It creates a "goldcard" which is used to SuperCID the Excalibur so that it doesn't care about what factory ROM you flash. Please have the factory (not a cooked) ROM ready to go.
** (This method is not intended for Newbie's and some enhanced knowledge of HTC devices and Windows is required to successfully work.)
** (Retry the second method several times with a few different factory ROMS before attemting the below)
Method 3: The third "goldcard" method is a bit more intensive and should be used as a "last resort" so follow closely:
(should unbrick ANY bricked Excalibur if performed correctly)
Get a cup of coffee or tea
You will need a working Donor HTC device with a microSD slot and a microSD card that is smaller than 1GB (will be formatted) to create "goldcard" image using QMAT tools as described below
You will need QMAT. Get it from http://revskills.de/index.html.
Go to the Download link and download the latest version and unpack QMAT
Have some coffee
Use a SD card reader (either USB for microSD adapter) in your PC to access the SD card through Windows. Format the SD card with FAT32.
* Insert the SD card into the donor HTC device and boot up the device. Connect the USB cable and establish an Activesync connection.
Open QMAT and go to the "Hardware Forensics" menu and select "Generate HTC Goldcard"
In "Select device key:" select the Excalibur
You will need the serial number fro the inserted SD card so click the "Get SD Card Serial from WINCE Device" button
Once the Serial number appears in the box, click the "Save Goldcard Image to WINCE SD" button below
If no errors pop up and all goes well, skip the next step
If you get an error or a popup saying "Goldcard for newer devices isn't implemented in newer devices", you must buy and register the software. Believe me, it's worth the small amount of $ you will spend to bring your expensive device back to life!
Now remove the SD card with the newly written Goldcard image from the Donor HTC device
Insert the SD card back into your PC using the microSD card reader adapter. Browse to the drive letter assigned to it. You will see no files on the SD card, this is normal.
(If, for some reason your PC sees the SD card as unformatted, something went wrong. Remove it and reinsert it into the Donor HTC device. The device should see the card as unformatted and ask you to format it, say yes. Now go back to the "* Insert the SD card into the donor HTC device" step above and repeat the steps)
Unpack your Dopod or other factory ROM and copy RUU_Signed.nbh to the SD card. Once it had finished copying, rename the file to EXCAIMG.nbh. Remove the SD card from the PC.
Make sure the Excalibur is off and insert the SD card
Enter bootloader mode as mentioned earlier (hold the camera button while pressing the power button). No need to connect the USB cable.
You will see a gray screen that says "loading". It will then find the EXCAIMG.nbh file and ask if you would like to start the update process. Follow the instructions and let the phone flash.
It will take 10-15 mins but your phone should boot fine and be back in action!
QMAT is a VERY powerful tool written by viperbjk that allows for full low level manipulation of HTC and WINCE tasks. Read all about it here http://revskills.de/index.html.
Many thanks to jockyw2001 for his amazing HTC device knowledge! Also thanks to all who contributed to this post.
Hope this tutorial helps!
Updates and more info will be here.
What if the phone will not enter bootloader mode?
ookba said:
Updates and more info will be here.
Click to expand...
Click to collapse
Hi OOkba,
This happened to a friend in the office's Dash. It simply froze up while operating. I actually got on the phone with HTC support. We couldn't get it to do anything. It does power up but then freezes.
The HTC guy was of the opinion that it is hardware related.
You ever solved that one?
BTW - I am running the 7.18 6.5 - love it - thank you so much
all steamed out said:
Hi OOkba,
This happened to a friend in the office's Dash. It simply froze up while operating. I actually got on the phone with HTC support. We couldn't get it to do anything. It does power up but then freezes.
The HTC guy was of the opinion that it is hardware related.
You ever solved that one?
BTW - I am running the 7.18 6.5 - love it - thank you so much
Click to expand...
Click to collapse
Thanks, glad you like it. Try this guide for your friend. Sounds like an easy fix unless it is indeed hardware related.
HI OOKBA. I can't find my shipped rom. I have a HTC Excalibur from Digitel, Venezuela. The serial number is SZ702FJ05879. I try all roms and not working. Please, help me. (sorry my bad english)
thank. I formated SD card and insert SD card in to my phone.But Do I need turn on my phone when connect with computer? because when I run QMAT software is error. " could not open connection? Device connected?". Help me. I need help from you
mydreamisrich said:
thank. I formated SD card and insert SD card in to my phone.But Do I need turn on my phone when connect with computer? because when I run QMAT software is error. " could not open connection? Device connected?". Help me. I need help from you
Click to expand...
Click to collapse
Yes, you have to have a spare working phone to create a "goldcard". The phone must be powered on and sync'd via USB so QMAT can access the storage card.
alfatech said:
HI OOKBA. I can't find my shipped rom. I have a HTC Excalibur from Digitel, Venezuela. The serial number is SZ702FJ05879. I try all roms and not working. Please, help me. (sorry my bad english)
Click to expand...
Click to collapse
English is good!! Who is your Carrier? Maybe your carrier has a ROM UPdate on their website? You should be able to use the TMO or Brightpoint ROM. You tried all the factory ROMS and they fail to flash?
ookba said:
Yes, you have to have a spare working phone to create a "goldcard". The phone must be powered on and sync'd via USB so QMAT can access the storage card.
Click to expand...
Click to collapse
I tried turn on my phone. And connect computer by USB but the same error. QMAT can't access the storage card. What does I do?
Sup ookba!
I really want to flash my TMobile Dash using your rom, looks pretty cool but I'm deadly afraid of bricking my phone so first, I took a look on my System Info and it says
ROM Version: 1.33.422.1 (tho its a TMobile Dash, I think the seller flashed it with this international rom).
Model Name: HTC S621
So I got 3 questions
1) Can i flash 3VO rom on this phone?
2) If the flashing fails, can i just use another 1.33.422.1 ROM and reflash it?
3) Will the flashing process (both ways) will bring the SIM Lock back?
Greetings from Brazil and sorry about my glass-cracking, horrible and ultra-bad english.
aletkd said:
Sup ookba!
I really want to flash my TMobile Dash using your rom, looks pretty cool but I'm deadly afraid of bricking my phone so first, I took a look on my System Info and it says
ROM Version: 1.33.422.1 (tho its a TMobile Dash, I think the seller flashed it with this international rom).
Model Name: HTC S621
So I got 3 questions
1) Can i flash 3VO rom on this phone?
2) If the flashing fails, can i just use another 1.33.422.1 ROM and reflash it?
3) Will the flashing process (both ways) will bring the SIM Lock back?
Greetings from Brazil and sorry about my glass-cracking, horrible and ultra-bad english.
Click to expand...
Click to collapse
Yes, your phone is fine. Make sure you follow all of the flashing instructions. Make sure you remove your SD card, connect your phone, run SDA Application Unlock, and run auto.bat from the update package.
mydreamisrich said:
I tried turn on my phone. And connect computer by USB but the same error. QMAT can't access the storage card. What does I do?
Click to expand...
Click to collapse
I dont know what you're doing wrong. Sounds like you're not establishing an Activesync connection properly.
Ok, Ookba. My carrier is DIGITEL and don't have support in the website. The phone comes originally with WM5 in spanish. I try all the factory roms and not working. Please, tell me if there is any solution or I forget the phone.
Thank you any help.
alfatech said:
Ok, Ookba. My carrier is DIGITEL and don't have support in the website. The phone comes originally with WM5 in spanish. I try all the factory roms and not working. Please, tell me if there is any solution or I forget the phone.
Thank you any help.
Click to expand...
Click to collapse
Try the "Goldcard"' method. This should SuperCID your phone and allow you to flash ANY shipped factory ROM. Please follow the tutorial closely. You will need a spare phone with a microSD slot.
Ok, Ookba. But the spare phone must be a same model than mine? (HTC S620)
alfatech said:
Ok, Ookba. But the spare phone must be a same model than mine? (HTC S620)
Click to expand...
Click to collapse
No, just has to Windows Mobile based and have a SDHC slot.
OK. I try with 3rd method and when run Qmat and select "Get SD Card serial from WINCE Device" appears the message "You need to set rigth registry permissions. See QMAT manual for more info." and not recognizes the sd card.
What is the problem?
Thanks, Ookba. You're great, man. Finally someone offers solutions to my problem. Thank you very much. My Phone came back to life again. I make a donation soon.
alfatech said:
Thanks, Ookba. You're great, man. Finally someone offers solutions to my problem. Thank you very much. My Phone came back to life again. I make a donation soon.
Click to expand...
Click to collapse
GREAT!!!!! Congratulations!
I tried but when I click Get SD Card Serial from WINCE Device in the box none found and click Save Goldcard Image to WINCE SD is card ID isn't 16 bit (32 charter) long. I isn't succesful. help me???????
Hi all!!
Ever since I got my Sprint Vogue, I have spent God only knows how many hours looking for and gathering information regarding this phone (flashing instructions, unlocking, SuperCID, etc). There are a few sites that have fairly comprehensive guides as to how to do this, but there are very few posts in the Vogue Section here at XDA-Developers.
Having said that, I figured I would create my own "How to Flash Your Vogue"-Thread. This is a multi-step process and I cannot emphasize the importance of following every step down to the "T", that is unless you are looking for a silicone-skinned brick...
Who is this guide for?
*Anyone with a CDMA version of the Touch. [highlight]That means no GSM[/highlight]
*Noobs and Seniors alike.
*People who have trouble flashing their devices.
*Anyone looking for links to more information.
*Curious people in general.
*Anyone willing to get rid of the nasty stock rom and looking for a newer and cleaner OS (notice that I never said more stable, so do not blame me afterwards ).
[highlight]Please keep in mind that there is always a chance of bricking your device with these procedures. I will not be in any way, shape, or form responsible if you damage your device while doing this.[/highlight]
Got your coffee? Alright, let's do this.
Step 1. Preparing the device
As with every phone, you have to make sure that you have the following things done before flashing:
* Battery charged at least 50%.
* All the necessary programs (see next post).
* Instructions handy.
Make sure that you back up all your information (contacts, e-mails, files).... essentially, anything that you would like to keep post-flashing. You can do this via Active Sync/Mobile Device Center or via third party software (PIM Backup is really good)...
You will have to reinstall every last piece of software in your device as it will be hard reset. Some programs may work if installed in a SD card directly, but a lot of them write things to the registry and copy files to the device, which they require to run. Long story short, keep all your cabs and exe files in a safe place so you can restore later if needed.
Step 2. Unlocking the Device (HardSPL)
Unlocking the device is done so that you can flash custom roms in your devices. The unlocker that you are about to download and use was provided by "ImCoKeMaN" at PPCGeeks. If you are interested in the full thread, please click here.
If you have read the above link, you will see two versions of the HardSPL (0.40 and 2.31). Simply use 2.31 as it works fine with most devices.
[highlight]To use this under Windows XP,[/highlight]
1. Connect your device to your computer and make sure it is synced with ActiveSync.
2. Download and extract the contents of the zip file, which is an exe. Let it run to completion. You will be prompted to disconnect and reconnect your device at one point in the process. Do it... don't worry
3. It will look like it is flashing a rom via a RUU. Do not disconnect the device after it is done!!!!!
4. Once it is done flashing, you will see a prompt that says that it will run exitbl. DO NOT DISCONNECT YOUR DEVICE. At this point, open ActiveSync, go to File>Connection Settings> Uncheck "Allow USB Connections". Continue following the on screen instructions and let it finish.
5. Go to bootloader once more to verify that it worked. You should see 2.31 CoKe MFG.
[highlight]To use this under Windows Vista/7 x64 (thanks jitajt),[/highlight]
jitajt said:
connect your device to WMDC (it's not necessary to set up device, just connect without setting up device)
then right click on the 2.31 unlocker and run as administrator
follow the directions, you will get an error about sleep.exe not being compatible with x64 but just hit ok and continue, (you will get about 10 of them)
then just keep following the directions in the command prompt and it will put your phone into bootloader then you have to disconnect and reconnect when it tells you to. and it will flash your phone and reset it. then your done you can close the command prompt and disconnect your phone.
I did it just like above and I have not had any problems.
Do this at your own risk as I am not responsible for your phone
Click to expand...
Click to collapse
Step 3. Flashing your Roms
The time has finally arrived. You sat down patiently through the unlocker and you are now ready to take the leap of faith into what you believe will bring your device to a new level of usefulness (also known as getting rid of that nasty, bloated, stock rom )
The process is relatively simple:
1. Download the RUU package from this post. I am only posting this because some cooks only post the rom nbh files rather than the whole package.
2. Go into the threads and look for whichever rom you prefer. Look at my signature to learn which one I am using. NFSFan (my current one) is by far the best one I have tried so far. You can download it from here
3. Put your device in bootloader mode and connect the device to the computer. [highlight]Once in bootloader, activesync will NOT see the device. If the RUU gives a connection error, try to run it with the devices in regular mode (with ActiveSync connected)[/highlight]
4. Open the Romupdateutility.exe and follow the steps.
5. Once it is done flashing the rom, disconnect it from the computer and hard reset it. To do this, simply hold "Send" + "End Call" +Stylus in the reset hole for about 3 seconds. It will prompt you to erase all the data and restore to factory defaults. Press "Enter", which is the center button in the directional pad. Once it is done, press "Send" to reboot.
Congratulations, you just flashed your first rom for Vogue
Step 4. SuperCID
This step can be skipped if you are not thinking of doing anything as far as your radio (such as flashing radios other than the ones intended for Vogue). This is also used to do other things such as modifying certain important things on your device such as the NV files, which is information that will not be discussed here. However, if you are interested in finding out more, simply google it, there is a ton of information out there.
Anyways, back to SuperCID... here is the procedure (thanks to hpnasik at mobile-files.com for the post)
1. Download the following special rom . This is an Alltel rom with radio 3.37. This was specially prepared to be able to reduce the Security Level of the device to level zero.
2. Download mtty since you will need it. Do not worry if you do not how to use it. You will have a step by step in this guide.
3. Flash the Alltel rom from above.
Now comes the fun part...
4. Disable USB in Connection Settings of Active Sync
5. Boot The Phone holding power button and camera button to enter bootloader.
6. Phone Will Display Serial in Bottom
7. Connect Phone to PC
8. Phone should Display USB instead of Serial in Bottom
9. start mtty.exe
10. Select All Default and Connect to USB in drop down box and Shoot the Following Commands (All Commands are case Sensitive)
11. run command rtask a : After this Command Phone will not Display any thing
12. run command echo_on : even though nothing is shown to screen
13. run command readCID : in Sprint it will display SPCS_001
14. run command writeCID 00000000 : Set CID Value to 00000000 replaces SPCS_001 in Sprint (This make PPC Radio Security Level to Zero)
15. run command readCID : This will Display the Update CID as 00000000
16. run Command retuoR : This will return to Original Boot Loader State
Congratulations, you just SuperCIDed your device. Original thread with the instructions can be found here if you are interested.
Step 5. Flashing your radio.
Now that your device has been SuperCIDed, you will have the opportunity to flash radios that have been ported to this device (ie. there is a version of the 3.42.40 radio for the Titan, which has been ported to the Vogue). There are two ways of doing this:
Way 1: Do it by flashing via RUU (same as with flashing a rom)
Way 2: Flash via microSD card. Simply put whichever radio that you wish to flash in the root of a 2GB or less microSD card formatted to fat32. Rename the radio to VOGUIMG.NBH and put your device in bootloader. The flashing will start by itself.
Way 3 (I know I said two ways...): There are a few stock roms that come with new radios. One of them can be downloaded directly from HTC and it is for the Sprint Touch. This one comes with Radio 3.42.30
The other one is for Bell Mobility and this one comes with Radio 3.42.50.
Why am I giving "Way 3" if the other two options seem much easier?? I have run into the problem where my device would not let me flash other radios than the one that I had. SD card method did not work and the RUU started out fine but quits at 8% rebooting my phone and displaying Error 328 in the RUU on the PC. Anyway, here are the links...
Sprint rom with radio 3.42.30
Bell rom with radio 3.42.50
Verizon Stock Rom
All Shipped Roms (All Carriers) - Thanks conflipper!
All Above Radios zipped
The newer radios perform a little better and give out better GPS signal (faster locks)....
Hang on a sec... did you just say GPS?!?!? But my Vogue does not have a GPS.... It does, just read a little further and be happy
Step 6. Enabling GPS, Returning to Stock, and Carrier Cabs
As I said before, there is a GPS hidden on your device. Now, if you are like me and went straight to the specs of the phone to confirm, you will probably try to call BS on this. Long story short, there are a few custom roms which have this "tweak" already implemented (like the one I am using from NFSFan). If you require some more info, I will post it later...
[highlight]Location must be on or else your GPS will not work. To activate it, go to Settings>Personal>Phone and change the Location setting to ON instead of 911 (thanks for pointing it out, th3lolz)[/highlight]
[highlight]For Verizon Users[/highlight]
br125 said:
For those of you with the official mr1 update from verizon that cannot get their gps working:
My xv6900 came with the official update and I got it working, it involves downgrading to a NON-GPS radio, then back to a gps radio...
go here: http://forum.xda-developers.com/showthread.php?t=533639
now the instructions are going to imply that you must load the unlocker before each flash... bs don't worry about that
1. flash the .40 unlocker
2. flash the non-gps rom (reset before customization)
3. flash the 2.31 unlocker
4. flash the vzw rom (reset before customization)
5. flash any custom rom or android rom
that's it, time consuming, but it works
*ignore the multiple flashing instructions, its completely unnecessary, I've never flashed more than once with no problem ever....
I also suggest keeping the vzw radio, but do as you will, I like the 3.37.38 radio.. ain't broke don't fix it
lastly, just make sure you RESET BEFORE THE CUSTOMIZATIONS RUN...... that is what locks your gps.
good luck!
ps. the verizon radio rom that is in that post is for the "leaked" 3.37.37 radio, I reccomend using the official update from verizon here for the 3.37.38 radio rom instead:
http://www.pcdphones.com/phone_downloads.aspx?bid=95&cid=1&mid=302&carrier=Verizon Wireless
RESET BEFORE CUSTOMIZATIONS
Click to expand...
Click to collapse
[highlight]How to Relock you phone[/highlight]
If, for whatever reason you need to return your phone for repair/replacement, you will need to relock it. To relock your phone, simply run the unlocker 0.40 and flash the stock rom of your carrier.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker.exe
[highlight]Carrier Cabs[/highlight]
Thanks to Codybear for gathering all of the cabs with settings for various carriers. But since the link went down, here is another one courtesy of LMiller1708
https://sites.google.com/site/vogueroms/vogue-files
This information was only gathered by me and I take no credit whatsoever other than trying to put it in a one stop thread. Thanks to the following people
Shadowmite
ImCoKeMaN
mindfrost
NFSFAN
Codybear
joshkoss
and a bunch of people that were involved in developing all this...
Thread sticky'd as requested
Peace,
Josh
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
dwigginstm said:
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
Click to expand...
Click to collapse
How exciting!! My first victi...erh patient
Did you put the device in bootloader mode? If you did and it is connected to the PC, you should see USB on the screen of your device. Also, do you have ActiveSync on your XP machine? You will need it for the drivers on this step. Changing USB ports sometimes help as well. And one last thing, do not use a USB hub, go directly through the USB ports in your computer. Good luck!
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
yes i have activesync set up with the phone and pc, but when i put the phone in bootloader mode and connect it the pc recognizes it but not activesync. is there another program i can unlock the phone with?
dwigginstm said:
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
Click to expand...
Click to collapse
Do not worry about ActiveSync. While you are in bootloader, the device is not running WM, which is why your computer only sees it as a USB device. This is perfectly fine. ActiveSync will not recognize it.
Please, follow the instructions in my post for unlocking. Read it thoroughly and try to understand it, else you will end up bricking your device.
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
dwigginstm said:
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
Click to expand...
Click to collapse
that is a message in the RUU. do not pay attention to it. good luck...
so i finally got the unlocker to start and it begins the ten minute process and stops then show a 262 error code ive done this over and over again
Let's go from the top. I just saw the message that you were talking about. The unlocker does ask for ActiveSync as you pointed out and it is asking you to connect the device to the computer. Then it asks for you to press any key when that is done. So, try that and you should see the word "initializing" with a dotted line getting longer for about 20 seconds. Do that.
The RUU will start up afterwards. The prompt will tell you that it is going to flash a new SPL, and if I am not mistaken that is where you are getting stuck.
Just out of curiosity, which version of the Vogue do you have? (Alltel, Bell, Verizon, Sprint, US Cellular)?
no internet
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
terrancextc said:
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
Click to expand...
Click to collapse
You downloaded a cab. Simply put it in your SD card and run it by tapping on it. Don't unzip it...
Unlocker is not 64 bit compatible... grrr....