Develop Bugs

HELP ME - COUNTRY ID ERROR

HOW I CAN UPDATE MY JASJAR FROM JASJAR_WWE_11353_137_10301 TO JASJAR_ITA_11346_126_10301_ship??
COUNTRY ID ERROR
Thanks and excuse my english

Just unpack/extract the JASJAR_ITA_11346_126_10301_ship file into a directory.
donwload the attached file to this same directory
Run it and the Country ID error will come out, run it again right after, and it should work

what you mean with "download the attached file to the same directory"....which file??
Thanks
Carlo Salvatore :x

thanks, but the update is ok without country error, but after the reset the screen is black with word: serial and v1.0

sorry...i found out the file you put for download but if i run the rom twice after have the rom and the file in the same directory i have the same error message....coul you please help me?
Thanks
Carlo Salvatore

carsa read pm

did IT!!!!...thank a lot...

carsa help me in private, please

edoalom hope everithing was fine!

i've the same problem, can you help me, too?

directory?
carsa said:
what you mean with "download the attached file to the same directory"....which file??
Thanks
Carlo Salvatore :x
Click to expand...
Click to collapse
I've got the .exe file and it simply wants to self-install in a directory with my JJ. So, which directory should I try to install this then?
thanks.
edved

Just extract the rom required using winrar or similar (normally done by right clicking on the file and selecting extract)
donwload the file "MaUpgradeUt_noID.exe"
Copy this file into the directory
Run it and the Country ID error will come out, run it again right after, and it should work

Italian to English
I purchased an imate jasjar in Italy last week. The salesperson confirmed that I can change the language from Italian to English. But when I contacted the Imate people they say it is not possible, Can someone guide me?
Thanks Felician

hanhha2000 said:
Just extract the rom required using winrar or similar (normally done by right clicking on the file and selecting extract)
donwload the file "MaUpgradeUt_noID.exe"
Copy this file into the directory
Run it and the Country ID error will come out, run it again right after, and it should work
Click to expand...
Click to collapse
Hi hanhha2000, the required rom that I wanted to flash is with a .exe extension behind, how can we use winrar with this type of file, hope you can enlighten me as I have also ran in Country ID Error problems, thank you.

Will this technique work for my i-mate JAMin? im just afraid to screw up my device completely cos iv heard that that can happen
thanx for your help pls reply asap

I've the same problem. can you help me to solve. tnk

DeVegas said:
Hi hanhha2000, the required rom that I wanted to flash is with a .exe extension behind, how can we use winrar with this type of file, hope you can enlighten me as I have also ran in Country ID Error problems, thank you.
Click to expand...
Click to collapse
Hi,
The way i use is run the update rom and when appear the Country error, open the windows explorer and copy the folder in the temporary folder to a new location, then put the file ...noID.exe in the new folder.

Why my SPV5000 don't want 1.30 rom ?

Hi, i have a SPV5000 and i can put a lot of kind of 1.13 rom inside, like Qtek or Orange.
But impossible to put any 1.30 rom (orange, qtek french or WWE).
I've tried a lot of solution like "put the radio first" ... rest after.
Do you know if it's possible that my hardware version refuse this 1.30 rom?
I think the guy who sell me the spv sell me a pre-serie .
Thanks

The first question I want to ask is: How do you perform the upgrade? Do you use the No ID Tool? If not, try using it. Here is an instructions I made:
The file is extracted in your computer. Once you run the shipped.exe file, you need to go to:
My Computer
Your Drive (mine is Drive C)
Show the contents of this drive
Documents and Settings
Choose your folder name
Choose "TOOLS" from the menu bar
Choose "FOLDER OPTIONS"
Click on the "VIEW" tab
Click on "HIDDEN FILES AND FOLDERS"
YOU WANT TO SHOW ALL HIDDEN FILES AND FOLDERS
Now go to TEMP folder
Now you will notice a bunch of folders will show up, tons of them to be exact. What you need to do now is click on the shipped.exe file again and "LOOK" for the folder being created because that folder is what you want to copy. If you did not see it created, you have to manually open each folder and look for the files I listed below.
Assuming you found the folder, you will have these following files inside that folder:
ms_.nbf----------------------this file is responsible for EXT ROM Version
nk.nbf------------------------this file is responsible for Windows Mobile Version
radio.nbf---------------------this file is responsible for Radio Version
EnterBL
GetDeviceData
readme
ROMUpgradeUt
RUU.conf
RUU.dll
UI.dll
MaUpgradeUt_noID
If the file MaUpgradeUt_noID is not there. You need to get hold of a copy of this file as you need this.
There you have it, REMEMBER, you need to have the MaUpgradeUt_noID file plus all the rest of the file in one folder if you want to upgrade to the ENTIRE I-Mate ROM, QTEK, O2, or whatever ROM you want.
If you only want to upgrade to the radio version then you need to delete 2 files namely: "ms_.nbf" and "nk.nbf". Leave "radio.nbf" alone and click on the "MaUpgradeUt_noID" file to initiate the Radio installation. Basically those 3 files control what you want to update on your device.
Hope my instructions were clear enough for you. Hope this helps.

Thanks for your complete response
Of course i'm using the MaUpgradeUt_noID ... i have no error message during the process but at the end after the hard reset i have black screen.
and to try to only flash the radio I renames other files .
thanks
I steel don't enderstand ....

Do you think the bootloader version is important ?
i have the O.56

SEB152030 said:
Do you think the bootloader version is important ?
i have the O.56
Click to expand...
Click to collapse
It won't hurt to try and update using Boot Loader Mode.
What do you mean "0.56"?

when I put my spv in bootloader mode, I can see on the screen :
on the top : USB
Botom of the screen V.0.56

SEB152030 said:
when I put my spv in bootloader mode, I can see on the screen :
on the top : USB
Botom of the screen V.0.56
Click to expand...
Click to collapse
You might be right. Your exec must be one of the earlier version. I remeber some time ago, someone asked the same question you did. Maybe someone else can help. Have you tried upgrading it using my instructions?

thank you again and of course I've tryed your method.
every thing works with previous version but not on 1.30
i spent 3 days on it .....

SEB152030 said:
thank you again and of course I've tryed your method.
every thing works with previous version but not on 1.30
i spent 3 days on it .....
Click to expand...
Click to collapse
I believe you need to find out how to upgrade the "Serial USB" application on your Universal for the No_ID Tool to work. Other than that you probably need a version of the No_ID Tool that works at an earlier version of the "Serial USB" version that you have. I'm sorry too, if I didn't help.

Help please, Original ROM request

My Diamond turned completely black due to microp error, I need the original ROM in the form of .nbh not .exe so I can flash it from the internal storage.

If you start the exe it will extract files to the same folder. One of them is the NBH file.

flupo2000 said:
My Diamond turned completely black due to microp error, I need the original ROM in the form of .nbh not .exe so I can flash it from the internal storage.
Click to expand...
Click to collapse
With the shipped ROMs, you can right click and extract them (you need winrar or 7zip or something like that installed). Then, you get an NBH and a few other files.

still have black screen
I cannot go the bootloader screen I did my best, please help

[Q] Extrat Radio Rom and flashing HD7?

Hi Guys
I have a HD7 from o2uk
I have flash the device with the new RUU_Schubert_HTC_Europe_1.69.401.01_Radio_5.54.09. 21_22.33b.50.10_Signed using a gold card.
But im getting bad signal, is there a way to strip the radio from RUU_Schubert_O2_UK_1.68.206.03_Radio_5.63.09.13_3a _22.36.50.15_Signed
and reflash back to the device?
Cheers
Kev

sutt359 said:
Hi Guys
I have a HD7 from o2uk
I have flash the device with the new RUU_Schubert_HTC_Europe_1.69.401.01_Radio_5.54.09. 21_22.33b.50.10_Signed using a gold card.
But im getting bad signal, is there a way to strip the radio from RUU_Schubert_O2_UK_1.68.206.03_Radio_5.63.09.13_3a _22.36.50.15_Signed
and reflash back to the device?
Cheers
Kev
Click to expand...
Click to collapse
what you could try is:
take the rom from with you want to use the radio.
rename the .exe to .rar and extract it.
remove the biggest .nbh file.
run the updateutility.exe and hope it will flash (if it works then it only flash the radio)
remember that it will always hardreset the phone (it isn't a custom ruu)
oh and remember ! it is always at your own risk

ceesheim said:
what you could try is:
take the rom from with you want to use the radio.
rename the .exe to .rar and extract it.
remove the biggest .nbh file.
run the updateutility.exe and hope it will flash (if it works then it only flash the radio)
remember that it will always hardreset the phone (it isn't a custom ruu)
oh and remember ! it is always at your own risk
Click to expand...
Click to collapse
But wouldnt that over write the rom on the device?

Ive extracted the rom using HTC ROM image editor.
I now have
GSM.nb
OS.nb
SPL.nb
I take it the Gsm.nb is the radio? but how do i create that into a image to flash?

sutt359 said:
Ive extracted the rom using HTC ROM image editor.
I now have
GSM.nb
OS.nb
SPL.nb
I take it the Gsm.nb is the radio? but how do i create that into a image to flash?
Click to expand...
Click to collapse
oh no not that .
one more time
1) take a rom (the one with the radio you want)
example:
RUU_Schubert_HTC_Europe_1.69.401.01_Radio_5.54.09.21_22.33b.50.10_Signed_SCHUBERT_TEST.exe
2) rename .exe to .rar and extract.
3) now you have a folder with some files
4) delete "RUU_signed.nbh" from the folder.
5) run ROMUpdateUtility.exe

ceesheim said:
oh no not that .
one more time
1) take a rom (the one with the radio you want)
example:
RUU_Schubert_HTC_Europe_1.69.401.01_Radio_5.54.09.21_22.33b.50.10_Signed_SCHUBERT_TEST.exe
2) rename .exe to .rar and extract.
3) now you have a folder with some files
4) delete "RUU_signed.nbh" from the folder.
5) run ROMUpdateUtility.exe
Click to expand...
Click to collapse
a similar case ... I can add languages ​​to the rom and then flash with goldcard?

manu81 said:
a similar case ... I can add languages ​​to the rom and then flash with goldcard?
Click to expand...
Click to collapse
no that isn't possible ,but you could change the rom with different languages .

Thanks ceesheim
This has worked just fine so where is the radio kept in the spl_signed? I did notce its change the spl too.
Cheers again
ceesheim said:
oh no not that .
one more time
1) take a rom (the one with the radio you want)
example:
RUU_Schubert_HTC_Europe_1.69.401.01_Radio_5.54.09.21_22.33b.50.10_Signed_SCHUBERT_TEST.exe
2) rename .exe to .rar and extract.
3) now you have a folder with some files
4) delete "RUU_signed.nbh" from the folder.
5) run ROMUpdateUtility.exe
Click to expand...
Click to collapse

[Q] Error [240] file open This is STUPID

I Read and Read and Read. The surprising part is that, what I need the most there is no video nor any instruction to fix the problem.
I'm trying to flash a ROM on my tilt 2 GSM phone.
I have already HSPL it,
I did task 29 using RhodiumWAdvancedRUU.zip because I couldn't get regular task 29 to work.
Now I get a white screen with HTC on it and it doesnt pass it. So I enter bootloader and make sure that at the bottom it shows USB. (yes I do see SPL-0.85. OliNex)
Now I try to install the ROM and here is where the problem starts.
My ROM:
I dled NRG MAXSENSE ROM which is Energy.RHODIUM.29022.Sense2.5.MaxSense.Jul.08.7z
My Rhodium Update Utility (RUU) is
Rhodium_CustomRUU_v1.1.zip
I Open it and I see
CustomRUU.exe
Here is where I don't know what to do. Some instructions say that I need a .NBH file. Where do I get this file. They say it should be with my ROM.
All I get when I dl the ROM is
Energy.RHODIUM.29022.Sense2.5.MaxSense.Jul.08.7z
Format 7z not .nbh
I get the Error [240] File Open when I run CustomRUU.exe. To fix it they say
"When this error message appears, check whether the downloaded image is placed in the DIRECTORY of RUU. If, for some unknown reason, you find that the ROM image is not located in the RUU folder, you have to download the RUU and retry again."
What is the "DIRECTORY" of RUU"? Whats a directory? I never heard that term before.
Of which RUU? CustomRUU.exe?
Do I make a folder and put CustomRUU.exe in it with the Energy.RHODIUM.29022.Sense2.5.MaxSense.Jul.08.7z ?
Where is the .nbh file? Do I rename the ROM IMAGE to .nbh?
Please give me step by step. Ive read so much already and I dont know what to do anymore. Thank you for your help.

-___- I cannot believe I spent all this time for something so dumb. We should put this on the Help for NOOBS thread. The file " .7z " cannot be opened with Winzip. To open the file you have to use WINRAR. And from there we can see the Rhodium_SoftwareUpgrade.exe (RUU) and the RHODIMG.nbh files. And double clicking the Rhodium_SoftwareUpgrade.exe the software will start walking you through the process for flashing. I think it would be a good idea to add on the HOW TO FLASH A ROM that the 7z file requires WINRAR to be opened.
But thanks to the Lord I learned how to flash the Rom successfully.
--------------------
He who provides for this life but takes no care for eternity is wise for a moment but a fool forever.
-John Tillotson

Or use 7-zip!

-Jonny- said:
Or use 7-zip!
Click to expand...
Click to collapse
Too easy lol