Hi,
I have HTC P3300 with WM5. Few days ago, it was not recognising the SIM (while it used to), & all of a sudden it started working. However suddenly it has developed another symptom. Phone pops up error called "Device.exe corrupted", how do i come out of this loop.
Regards,
Vinay
Make sure your data is backed up and do a hard reset.
How about upgrading to WM6?
Related
I have a problem flashing my O2 XDA exec. After double-clicking the EXE supplied by O2, it now just sits at an unlit screen with "SERIAL v1.00".
I've tried a hard reset (the two dashes and reset), but it still wont come back to life.
Any Ideas?
I had the exact same problem with my Tmobile MDA pro. When you plug in the usb cable the serial should change to usb. If not trying taking the battery out doing a full reset and putting the battery back in then do a soft reset. If you can get to the stage where you see it change to usb when plugged into pc your in bootloader mode still and all is functioning correctly. Try sending the firware update again. I was flashing to the Imate firmware and must have tried about 6 times before it worked. Each time on the pc follow the instructions if it errors and asks for a soft reset, just keep trying. In the end i got the firmware to flash succesfully but coulldnt get out of bootloader mode. So instead I just kept trying Radio 6.0 firmware only and it worked after the 4th time. I did a full reset my MDA Pro rebooted succesfully and ive never been so happy. Good Luck hope your outcome is as happy.
Hi.
I recently got a refurbished Axim X50 midlevel. It came with rom A01 for WM2003. I grabbed A05 from the Dell site and installed it. Everything worked fine, the computer told me the update worked successfully and the PDA was reset.
However, when it reset, it froze at the screen that shows DELL right in the middle. I gave it a good 15 minutes, but still nothing.
So I got into the SD loader and tried to upgrade it to WM 5. The bootloader loaded successfully and the image was half way through flashing when I got the update failed message.
At this point, I was suspecting some of the memory was corrupted, because the SD card was fine. I did the diagnostics and everything checked out perfect. Tried to take it back down to WM 2003 A05 and the bootloader flashed, update was successful but again it froze after the hard reset. What's going on, can anyone help? I really started to like this thing!
Thanks
Hello everyone.
Apologies if this has been addressed somewhere already, but if this is the case, I was unable to find it.
I have a French Orange Diamond, which I was able to flash w/o problems with Hrad-SPL 1.30 by Olinext, and then with the RUU_Diamond_HTC_Europe_1.37.401.3_Radio_Signed_Dia mond_52.26a.25.09_1.00.25.03_Ship Rom. This worked flawlessly, and I have been a very happy camper since!
Tonight, I tried to upgrade the radio ROM to 1.00.25.05. To do so, I first installed the developer version of Hard-SPL 1.40 by Olinext, which went very well. Then, I tried flashing the radio, and instead of getting the bootloader, I got the colorwheel, and almost immediately afterwards the phone screen faded to complete black. After a little while, the ActiveSync (4.5) window disappeared from my XP SP3 PC screen, and the phone waited there until the flash process timeed out and it entered recovery mode. This happens every time now, and I am always able to recover perfectly.
Thinking it might be related to the Hard-SPL, I flashed back to version 1.30 by Olinext, and then even reverted back to the stock 1.37. Whenever flashing an SPL, the screen still fades to black, but the process completes ok, whereas whenever I try to flash the radio, it will always time out with an Error 262, apparently comms-related.
Has anyone encountered this in the past? Anyone know what/how to fix?
Thanks!
P.S. I forgot to mention that if I copy the EnterBootloader.exe onto the phone and run it from there, the screen will also fade to black in exactly the same way.
Hi All,
I have a VZW Htc One M8, and I have been playing with it when have gotten the chance recently. I have installed/flashed an RUU before to correct an issue I ran into (trying to take an OTA) and everything went smoothly. As I said I took the OTA, but kept the RUU from the previous time I used it (first mistake). I am s off so I am hoping that is going to save me here.... This brings me to my problem.
I was trying to flash Viper Rom, but at the end of the setup I kept getting a popup saying setup has stopped, and I was unable to see a homescreen, but the phone was working. I decided to revert back to stock using the old RUU (be gentle) and it loaded and I hit yes to begin. About 10 second in it stopped and wanted me to reboot... I was in the middle of doing something else when it happened so I rebooted back to the bootloader and my OS line was in red. I then went back to recovery and restored my very recently created backup of my stock rom, which worked. I then went back to the boot loader to look at what was in red more closely and it is now blank. It says OS but then nothing after.
I have since gotten the new RUU that I should have used, but it seem to hang on the last part of the loading (put in on my external sd card) and my phone works... but the boot take forever and the VZW logo doesn't come up anymore. It almost seem like the phone boots fine but the HTC ONE logo stays until the phone screen turns off and when I hit the power button to turn the screen back on the phone is booted. My question is... should I 1) try the old RUU again and then take the ota since I am s off I have seen that technically it should work. 2) let the phone sit at the loading of the newer RUU and see what happens (I haven't tried seeing if the old RUU will load yet) or 3) count my blessings and deal with a non completely broken phone?
I realize I made a few errors while doing this, but I am hoping that s off will allow me to correct the problem. Any help would be greatly appreciated.
Issue should be resolved
Sorry to everyone that read this... I didn't make it all the way through the thread where I found the new RUU, and the thread tells how to resolve the problem with not loading all the way. I am going to try the fix after work.
Edit 1: problem resolved... I am an idiot
Hello, I apologize for my English, I use the translator.
Would anyone find someone willing, and ppmohl me?
I bought for ali for myself and my friend two radio isudar with android 7.1.1, 2gb ram, 16gb rom.
I tried to both radio in my car.
Both of them were normally released, but after a while they were stuck and restarted, started, but after a while they jammed and restarted, then jammed when booting the system.
It happened several times in a row, eventually it does not turn on at all, the other sometimes starts, but gets stuck when the system starts.
The seller sent me an update as well as instructions on how to do it, but one of my radio will not run at all and the boot loader will not start on the other, and will boot into the system.
The update process sent by the manufacturer does not work.
I have already bought several pieces of radio by ISUDAR, always with a system of wince, they all work. I tried even the android, another little one. Did it work well?
Will anyone advise? Thank you very much