Develop Bugs

My Qtek 9000 died after upgrade

Hi to all. After that i have upgraded my Qtek 9000 Vodafone with NoID software, at 99% the device it is blocked. No Boot Display. No Lamp.
I can to solve the problem? How i can enter in boot loader mode forced?
Pse help me!
Thanks.

Power + Light + Reset

rikram said:
Power + Light + Reset
Click to expand...
Click to collapse
Died.
Boot rom is cancelled from PDA?
There is a another mode ?

Help Me!
Help me!
Another Idea?

Power+light+reset = bootloader mode as already posted. It does not light up though, you can only see the bootloader screen if you look at it in bright sunlight or shine a light at it. Try charging it overnight the press power+light+reset, connect it to your PC then run the upgrade. If it really isn't going into bootloader mode then you will probably need to send it off for repair to vodafone.

i just had exactly the same problem, even the pc does not recognize it at all, activesync doent work, what to do please

lion2000 said:
i just had exactly the same problem, even the pc does not recognize it at all, activesync doent work, what to do please
Click to expand...
Click to collapse
I do not have hopes. There is not image on display. I have tried with power+reset+lamp hard reset - + - + Reset!!! Power+ camera + Reset!!!
Display black and nobody written of the boot loader.
Useless if the boot loader it is cancelled is not restorable. Unfortunately it goes in repair.

i have the same problem with my MDA PRO. my MDA PRO also does not show bootloader screen. even not is charging by its charger. i just wanted to upgrede it with AKU and after i upgraded it, it did not open even bootloader screen did not appear.

fuhayer said:
i have the same problem with my MDA PRO. my MDA PRO also does not show bootloader screen. even not is charging by its charger. i just wanted to upgrede it with AKU and after i upgraded it, it did not open even bootloader screen did not appear.
Click to expand...
Click to collapse
I have not solved. I sent device to assistance.

mne now shows the boot screen, it comes with some funny colours, but it stays there, whe i ckicj sof+soft:reset it comes with screen
press o to restorefactory default
press x to exec
when i press 0 it goes back to that funny colourd screen, dont no what to do
any help?

what is soft+soft ? how did you get boot screen ? which phone are you using ?

How it can happen? If device worked before u start upgrading maybe u battery is low. Try to charge it somehow even not fully and continue upgrading via bootloader screen.

yes, universal. good news, i got it back to life, it now an i mate, can't change it, but it works.
i tried many rom version that i downloaded from buzzdev and one clicked.
most came with country id wrong etc
how can i gdt it back to O2? it does not accept it anymore?

tabasco said:
How it can happen? If device worked before u start upgrading maybe u battery is low. Try to charge it somehow even not fully and continue upgrading via bootloader screen.
Click to expand...
Click to collapse
Shalom tabasco, well not really, i had it like that for a week, i evenhad it on charge for almost 3 days, the screen came at one point when i upgraded a rom, but the screen had a funy colour and it was stuck in bootloader, done all reset you can imagin, i even rand O2 to collect it for repair

seems to me that I created a problem for myself too. Can't escape bootloader mode. This 3 stages runs fine, but after final 100% CE screen, when I doing hard reset, writes "Clearing now" and goes back to bootloader screen :roll: How to make him alive? I even did short on backup battery (opened back cover), but nothing effective
ok ok i pressed several times buttons which activates bootloader and it comes to normal activity. Was it a joke or something else ?

Good for you

Did u try to do as given here? http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen - do all this, maybe it will solve. Be ezrat ashem
But anyway I'll going to make him swallow this new ROM from T-Mobile, but later, not at work... :wink:

hi,
did you solve your problem yet ?

Artemis doesn't boot after langauge support uninstalling (details inside)

Hi, I'd really appreciate any help.
I recently bought the P3300 and installed Hebrew language support. After uninstalling it the phone restarted itself, and since then it gets stuck on the "windows mobile" logo screen. I tried installing any possible ROM I could find via the bootloader screen, but with no success. With each ROM I've tried a different error message came up. I also tried to use the USPL.exe but it couldn't detect the phone.
IPL 3.07.0001
SPL 3.07.0000
GSM 02 69 90
OS 3.7.00
WM6
Thanks in advance.

Let find the Original rom and flash again. good luck

Do a hard reset!
Press and hold both soft-key buttons, stick the stylus in the reset hole, release reset and wait for bootup to begin before releasing the soft-key buttons.
As I recall you get a confirmation screen.

sandoval said:
Do a hard reset!
Press and hold both soft-key buttons, stick the stylus in the reset hole, release reset and wait for bootup to begin before releasing the soft-key buttons.
As I recall you get a confirmation screen.
Click to expand...
Click to collapse
Thanks for the tip, it worked

unknown problem

dear friends ,
my phone has shut down and only when you take out the battery and put it back in after which you press any button on the phone it comes on and shows the htc logo after which it displays the following
ipl 3.07.001
spl 3.07.000
gsm 02.69.90
os 3.7.0.0
remains on for about 5-6 seconds and goes off
have tried to enter the boot loader mode by pressing the record button and reset button but it continous to behave in the same manner as mentioned above .
also when i try to charge the phone it shows only a red light
hoping someone can offer a solution to my problem
thanks and regards

I'd also be interested to know about this as my MDA Compact III has just done exactly the same thing.

have you guys tried flashing...that could kill it if not done propertly....but i doubt,the led is on,splash screen appears...info appears...what were last few things you did
according to spl os and ipl you flashed artemis touch 4.02 if i'm not wrong...or maybe tom's v5...try reflashing the same rom or just try a hardreset

Interesting...I've recently flashed the same ROM (v4.02)
I am certain I followed all the instructions about USPL and its been working fine for about a week...then it just went blank!
Will try re-flashing and/or a hard reset.
Thanks for the advice.

mrd5477 said:
Interesting...I've recently flashed the same ROM (v4.02)
I am certain I followed all the instructions about USPL and its been working fine for about a week...then it just went blank!
Will try re-flashing and/or a hard reset.
Thanks for the advice.
Click to expand...
Click to collapse
well...if it worked i'm sure you installed some app or deleted some files...so the system doesn't work...
if so hr will help

dear friends,
took the device in for repairs the fault was with the power circuit board which had to be changed as`informed to me by the technician
i now remember a few months ago the power button stopped working and a few days before the phone went bad it would work intermittently but there was no spring in the button hence it would have to be pressed quite hard for it to work i feel that this loose power button caused the power circuit to fail also my sd card was spoilt and the same had to be replaced
cast me appx in usd 30 for the repairs
thanks

TMobile Dash Crash

A friend gave me a TMobile Dash which only crashing on the second TMobile screen, wont go any further than that. Active sync won't detect it. I have tried to hard reset with no luck. I can access the bootloader mode and it shows:
Excalibur
ONBL 1.22.0000
Excalibur
SPL 1.22.0000
Excalibur IU
Is there anything that can be done to revive this phone?
Thanks

Yes you can hold down the sym button (camera button) located down to the right of the space bar. Hold this button down for about 5 seconds and while still holding it down plug in a usb cord and you should see a tri-colored screen. Then flash the phone with the original offical rom (t-mobile rom) which can be download from the link below. Once you have this going you can then update to the 6.1 by following the tutorial. Let me know how it works.

I see a choice of three ROMs for TMobile Dash would anyone do the job?

Yes anyone would do the choice, the most recent one is the lowest one (3rd).

I used 1.22.531.4 an it still only just stays at the second tmobile screen.
1.22.531.6 is has a RUU_signed.nbh file in it not to sure how to use this.
Any other fixes?

Try to use another one, see if it works. And also, are you running it from your computer...

Yes I am running it form my computer. None of the others are working either.

????
WongItal said:
Yes I am running it form my computer. None of the others are working either.
Click to expand...
Click to collapse
When you have the phone in Bootloader mode screen?what is the code that it is giving you? Also how are you getting the phone to hard reset if you cannot get past the second screen?

The is what I see ont eh bootloder screen
Excalibur
ONBL 1.22.0000
Excalibur
SPL 1.22.0000
Excalibur IU
I held the 2 soft keys and pressed power button then black screen comes up then i press the green phone button.

Is there anything else that can be done or is this phone now a paper weight?

Help with HTC Touch Diamond, won't boot

Hello, this is my first post here. I tried to install Windows Mobile 6.5 as indicated in Gizmodo http://gizmodo.com/5281397/how-to-install-windows-mobile-65-right-now but it didn't work and now my phone won't boot.
The phone is an HTC Touch Diamond from Sprint. I followed all the steps indicated and everything look fine, but after installing the OS the phone displays the screen TOUCH DIAMOND, and then restarts and displays the same thing. I'm able to get into the boot loader (Tri color screen) and says:
DIAM500
SPL-0.57.CMONEX
MicroP-Diam (LED) vB
PSOC-Diam STAGE_EVT v20.
I don't know what to do now
Thanks

try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..

dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.

Flash from Olinex 1.40 screen?
okokur said:
dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.
Click to expand...
Click to collapse
Hi I have the same issue on my HTC Diamond. I flashed wm 6.5 and it was working fine, then it hanged on titanum weather. I reset and it stayed on the HTC Diamond page, I did hard reset and got the Olinex 1.40 3 color page. It does respond from serial to usb when I plug/unplug. Can I reflash without active sync?
Turns out I was able to flash, but both roms I tried work well on 1st install, but stay stuck on the Touch Diamond screen everytime I restart de device. Is it a problem with the radio not compatible , or is there a specific Hspl for each ROM???

I found solution for this problem. If your diamond won't boot go to bootloader mode and upgrade your radio http://modmydiamond.info/index.php?option=com_content&task=view&id=15&Itemid=26 and after that your dimond worked fine without loosing data.

try to hard reset the phone by pressing vol down key + the center button + reset button.
if the problem is still like dat..
try to install another rom..

davidwong007 said:
try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..
Click to expand...
Click to collapse
Thanks davidwong007 for your help, I was experiencing the same issue as op and your method did the trick. For a minute there I thought I had bricked my HTC Touch. I did step by step what you suggested and ended up in the rainbox screen, once I was able to do that, I knew there was a hope. i did a full factory reset of the phone and voila the phone fully booted, the pain in the butt touchflow loaded. Very important thing I forgot to do in the past is to back up my phone, after the restore you will lose everything on phone, except what is in the internal storage. Thanks again.