Whenever I have my Plantronics 665 connected to my HTC WM6 S621 the phone only vibrates, and rings through the headset. How can I fix this? I tried a reg hack, but reverted when it didn't work.
This didn't happen with a Jabra JX10, so it may be the headset. But I'm convinced there's a working fix out there. Any help?
Related
--------------------------------------------------------------------------------
Hi!
I have i mate JasJar, but there are some problems which are a bit annoying and I will ask you if you can help
Does anybody have problems using BT Jabra 500 working with Jasjar?
I cant hear any of my incoming/outgoing calls nor can I hear a ringing in BT.
Jasjar discover BT and pairing is OK ( just in case I did couple times -no luck)
when I use answer/end button on BT is dialing out but no sound on BT
on other side that I call they can hear my voice but I can't hear anything
Do I need any software to instal in jasjar ???
ROM version 1.13.53 WWE
ROM date 09\23\05
Radio version 1.03.01
Protocol version 42.36.P8
ExRom version 1.13.137 WWE
Please help me out
Thanx
I have BT 500 and have no problems, it sounds like the headset has a problem not the phone.
Also have my own and a client's Jabra 500 working successfully with o2 Xda Execs.
Stupid question I know, but you have tried increasing the volume on the headset buttons?
I did try everything , volume etc , contact jabra and try there sugestion
such as :
could be a pairing issue, or a bad speaker on the BT500. Please try a reset and re-pair of the phone and headset first:
Turn the headset off.
Plug the headset charging cord into a wall outlet.
Connect the headset to the charging cord for 5 seconds.
Disconnect the headset.
Remove the headset from the phone Bluetooth menu.
Turn the phone off.
Remove the battery (and sim card, if removable), and hold out for 5 seconds.
Re-install the battery (and sim card, if applicable) and turn the phone on, but do not touch any settings.
Turn the headset on.
Put the headset into pairing mode by pressing and holding the pairing button until you see a steady blue light. Release the button.
Perform the pairing procedure for the phone.
SIMPLY IS NOT WORKING
try with friend V3 razor and same thing
I also have the BT 500 + jasjar
It just works better than the BT 250 which was my past one.
To be honest, what I have on my jasjar is the new O2 rom upgrade (and that should not do any difference) I think there is something wrong with your jasjar
Maybe you will be forced to try the bad solution HARDREST try the headset with other phones before doing that
i beleive it's the headset that has the problem, since you tried it with another phone.
i have the bt500 with the imate jasjar and also the kjam and it's more than perfect for me, the sound is cristal clear on all the phones i tried on.
maybe you should replace it with a new one.
What I mean is not a factory mistake in the headset
I think the phoen is getting complex and some data have been lost (possible)
By the way, I haven't installed the BT headset fix, yet it works fine.
Hi,
I have this strange problem. I'm using the Black Majik LE and a i.Tech Arrow X headset.
I'm able to pair both of them successfully - completing with the i.Tech Arrow X added (that's the only bluetooth device i have).
However the headphone icon does not appear on the taskbar and i cannot make/receive calls through my headset, it seems as if its not paired, all the audio/mic goes through my Hermes.
I checked that the bluetooth is on (blinking blue light), resetted my Hermes, delete the pairing and re-paired, resetted my headset, all with no avail.
To confirm that my headset is fine, i paired with another phone (Sony Ericsson) and its working fine, so its definitely a problem on my Hemes.
Has anyone encountered this before or have any suggestions on how to resolve this?
Thanks!
I have the same problem with official WM6....
Suggestions anyone?
I to have this problem, I could connect my bluetooth headset fine before to listen to music but now all music is played out of my dopod 838 pro and doesn't come out of the headset at all its like its not there and i've also done all those steps you mentioned Patrick.
Bluetooth headset works great on my official WM6. I've tested with both Jabra BT 620s and Pulsar 590A. I can receive phone calls in of middle of the music. No problems at all.
Maybe it has something to do with your BT headsets?
racoon82nz said:
Bluetooth headset works great on my official WM6. I've tested with both Jabra BT 620s and Pulsar 590A. I can receive phone calls in of middle of the music. No problems at all.
Maybe it has something to do with your BT headsets?
Click to expand...
Click to collapse
I flashed to vp3g's v3.0 and the BT headset works fine.
Flashed back to Black Majik LE and the BT headset works again
Weird.
Thanks for all your help anyway
I've flashed back to WM5 headset works fine but back in WM6 still not workin for stereo only for phone calls.
This may seem like a silly question, but under bluetooth connections, did you try selecting (and holding) the bluetooth device and then selecting the option that says "Set as Hands Free" (or wireless stereo if you want to listen to music)? It seems like some older rom I had didn't require this, but now I have to do this each time the device is turned on or off.
First of all, I would like to says big thank to all rom cooker. You all did a very great roms. However, I still have a little problem that annoy me a lot...
I had connected the stero bluetooth headset with Hermes and choose both "Wireless Stero" and "Headset" profiles in bluetooth setting.
Then when there is incomming call, the Hermes will not ring. So I had a lot of miss calls.
However, if I disable the "Wireless Stero" profile in bluetooth setting, the Hermes will ring normally.
I used to use the Prophet before and there is no problem. The Prophet will ring normally although I choose both profiles.
The stero bluetooth headset is the same, iTech Clip Radio.
I had tried on many roms and found the same problem. So I guess that maybe I have to modify the registry setting to enable ringing on "Wireless Stero" profiles. Can somebody help me to solve the problem please???
I have the same issue and assumed that's how it worked since I just got this Jabra BT8040 that supports wireless stereo. It would only ring through my headset when wireless stero was enabled. If there is a way to get the phone to ring also that would be great. Right now I do the same thing as you, disable the wireless stereo until I need to use it.
My guess is this is by design since all sound is routed to stereo headset then so would the ringer. This isn't an issue for me since the Jabra BT8010 I can turn on/off stereo by simply pressing a button on the headset.
Sorry don't know of a solution.
Thinking about it I guess you could use something like mortscript and make a button that turns stereo pairing on/off to make it simpler I dunno.
I have similar issues with the PAYS rom, when listening to music via my BT earpice (Jabra) where you click the answer button on the earpice it then takes the music from the device and plays it through the jabra ONLY for about 5 seconds and then defaults back to the device?
Any suggestions would be appreciated?
Hello all. I'm new to windows mobile but not to smartphones. For some reason my bluetooth headset is not working. I have not installed TomTom or had any error messages, basically I turn on the bluetooth function on my TP2, then turn on my headset, it goes to search and never finds my headset. It finds everything else, my blackberry, another cell phone, but not my headset. Any ideas?
Headset not in pairing mode or not visible? If you have another bt device, use that to test.
I thought I had it in pairing mode but apparently I didn't lol. Problem solved, thanks!
Hi,
I own new Desire phone and paired it with BT headset.
Once done when someone calls my mobile the phone vibrate but not rings and the sound is heard only in the BT earpiece.
Since i do not go aroung with my BT device attached to my ear i miss calls if i do not feel the vibration.
Can anyone faced such issue and have a solution?
Any ides?
Thanks
Shmuel
Tap and hold your bluetooth headset pairing - is it also paired as a bluetooth media device? If so, just un-tick that optiona nd you should et what you are wanting.