Related
Hi, after speaking to Midget_1990, I have patched the RUU for the Universal to allow flashing with any CID on your phone, this is the official Universal RUU (with a slight GUI mod by someone Midget_1990 mentioned)
so have at it... enjoy.
thanks, was just about to upload it
thanks,
just downloaded and have a try
allway said:
thanks,
just downloaded and have a try
Click to expand...
Click to collapse
it does work... just has the minor caveat that it'll try to flash a Universal when it's not actually plugged in... so try not to be a complete plank with it.
Olipro said:
it does work... just has the minor caveat that it'll try to flash a Universal when it's not actually plugged in... so try not to be a complete plank with it.
Click to expand...
Click to collapse
i have flashed my universal with the new RUU.
It works fine.
Olipro
Is it possible that you will make a HardSPL for Universal?
We still have no way to recover bricked radio...
we were discussing that earlier. the nogsm shows when the radio bootloader is not written to the device properly for whatever reason. its still early days but it may be possible to create a new radio bootloader that cant be overwritten so that problem wont occur. however it wont fix thoses who allready ahve the problem.
Skwyk said:
Olipro
Is it possible that you will make a HardSPL for Universal?
We still have no way to recover bricked radio...
Click to expand...
Click to collapse
ok, if you are flashing a radio, and you brick your radio, but not the radio bootloader, then you should be able to recover by reflashing.
if you brick the Radio bootloader, then unfortunately, there is no way for you to recover from this; possibly the only way of recovery is directly accessing the radio chip pins via whatever interface it is... perhaps i2c? and flashing on a radio BL again through a separate interface... meaning you then need a radio bootloader binary in the correct format.
Olipro said:
ok, if you are flashing a radio, and you brick your radio, but not the radio bootloader, then you should be able to recover by reflashing.
Click to expand...
Click to collapse
Not in 100% of the cases... there are some situations where the radio bootloader is intact, but the radio is screwed, this causes all bootloader commands that require radio seclevel to be queried to hang the device (like 'task 32' or 'info 2'), thus not being able to flash it with the usual RUUs.
If this happens, it can easily be fixed with hermflasher by flashing the raw radio without prior authenticating to bootloader.
Olipro!!! am having No GSM here!!!
Dear Dr. PDAs
My Universal is suffering for bad blocks of Radio ROM i guess.
it Says NO GSM when boots.
Boots WIN CE very well
can't flash radio rom.
Please tell if we could have HardSPL for Universal or is there any other way to recover it...
waiting.
farehmani
hi everyone i m in need of new rom for my XDA Exec Universal plz help me as i m ver new.
V1640 and flash rom radio problem
hello,
On my V1640 my radio rom is version :0.00.00, and I can't flash it with a newradio rom. It is probably a CID Lock problem, How works Universal RUU ?
Is there a tutorial for flashing with Universal RUU ?
thanks
Regards
Has anyone got anywhere to fix problems with radio mess ups I have an O2 XDA Exec and loads 2.05 ok but error when flashing any Radio. Tried all I can find but no luck
simpleparab said:
hi everyone i m in need of new rom for my XDA Exec Universal plz help me as i m ver new.
Click to expand...
Click to collapse
Try to serch forum
Or, for lasy people try my folder blow
Flashing radio rom Ok !!!
I flashed the radio rom on another PC.... It works fine.
Try this..good luck
Flashing the O2 original ROm with this RUU
Hi,
Can i use this RUU combined with the original ROM from O2 to flash?
My current ROM:
ROM 1.13.82
Radio 1.04.02
ExtROM 1.13.188
New ROM available:
ROM 1.30.107
Radio 1.09.00
ExtROM 1.30.162
I have to use the bootloader mode to flash the new ROM because my XDA Exec has problem on connection with my PC via Active Sync. My Xda just dont sync with my PC where there is no connection established.
Hopefully someone can tell me what is this RUU? Whats the different than the original?
bejoa said:
Flashing radio rom Ok !!!
I flashed the radio rom on another PC.... It works fine.
Try this..good luck
Click to expand...
Click to collapse
this is the second time ppl have been able to flash no GSM Universals by using a nother PC. What was the spec of this pc and what was installed and Not installed in it.? I really want to unbrick my Universsal
I flashed my universal on a Laptop :
Gericom Select 2580+
AMD 2500+, 512 Mo ram, 80 Gb HD,
Windows XP Home SP2 pack
ActiveSync 4.2
Universal RUU
nothing special installed...
Good luck
bejoa,
what was the boot loader version of ur universal?
It is version 1.0
Hi,
I have the following question. I currently have installed HardSPLv7 (so the device shows IPL-1.04 / SPL-2.20Olipro.
How exactly do I downgrade to my old IPL-1.00 / SPL-1.06 in case I have to hand-in my device for warranty reasons? I already searched through the forum and read that it can be done using sspl somehow but I couldn't find exact instructions.
Can anybody (maybe pof) give detailed instructions on how to downgrade to original ipl/spl from a .nbh with the correct ipl/spl files. I already prepared a .nbh with a spl-1.06 and the corresponding IPL extracted from an original vendor rom and put in my rebuilt dumped rom.
I also have the problem that I don't know where to get IPL-1.00, because on the page where to original roms are listed only the SPL version is noted, but not which ipl is in which rom. Can anybody tell me where I can get an IPL-1.00 .nb file?
Thanks for any help on this. I also think that maybe it could be interesting to put this onto the wiki if I anybody can answer this.
Thanks for any help.
check you PM
It's already pretty much in the Wiki, maybe a 'downgrade' link would be prudent.
Upgrading and cooking: -> MrVanx Hermes upgrade guides -> SPL Downgrade Guide
IPL-1.00 / SPL-1.06? Is this working
Hi,
I just read through the mr vanx downgrade guide and found out that there is a downgrade package with IPL-1.00 and IPL-1.04 and a second one with IPL-1.01 and IPL-1.06.
Now, I have the problem that my device was shipped with IPL-1.00 and SPL-1.06? Apparently this is a strange combination as this is not downloadable at the mr vanx downgrade guide, so my question is. Can I simply extract the IPL-1.00 from one .nbh and SPL-1.06 from the other and recombine them using rombaker, or would a downgrade to this combination screw up my device?
Thanks for letting me know.
I'm on the same boat, I need to downgrade my JasJam to send it in.
I haven't researched at all yet, i've been pretty busy. when I get off work i'll look into it and see if I run into the problem your facing and we can atempt to solve it together.
fone_fanatic said:
I'm on the same boat, I need to downgrade my JasJam to send it in.
I haven't researched at all yet, i've been pretty busy. when I get off work i'll look into it and see if I run into the problem your facing and we can atempt to solve it together.
Click to expand...
Click to collapse
Easiest thing to do is to download your original shipped ROM and extract the NBH file (using dutty's good nbh tool) and grab the IPL or SPL that you need and substitute that for the file from MrVanx. Just be careful what you flash - if you mix up the IPL and SPL file - InstaBrick! Trust me - I know
Do as ToddJG says, download the two files which i refer to in the guide.
Extract the IPLs and SPLs from the two files, mix and match.....BUT BE CAREFULL.......DONT FLASH UNLESS YOUR PREPARED TO DO IT.
ipl 1.00 and spl 1.06 will be fine.
make a single nbh from the mix and match combination then flash with customRUU.
What if i'm trying to flash the original shipped rom.. and i do the first step in your guide, then simply flash the shipped rom, or do i still have to extract the ipl and spl? (they're already extracted just wanting to know if its redundant if i recompile it with the rom i extracted them from.)
Ok, just succesfully downgraded to IPL-1.00 and SPL-1.06. Now i'm gonna flash back to an imate shipped WM5 rom. but one problem with that... clubimate.com is only showing the extroms which are around 6mb when downloaded.. where can i get the full imate rom?
also mrvanx what do u mean by this:
As with other downgrade guides this is NOT intended as a guide for claiming the warranty of the device having flashed components which are not authorised by the manufacturer or carrier.
Click to expand...
Click to collapse
?
fone_fanatic said:
Ok, just succesfully downgraded to IPL-1.00 and SPL-1.06. Now i'm gonna flash back to an imate shipped WM5 rom. but one problem with that... clubimate.com is only showing the extroms which are around 6mb when downloaded.. where can i get the full imate rom?
also mrvanx what do u mean by this:
Click to expand...
Click to collapse
It means that if you flashed unauthroized phone parts (like unofficial WM6 roms, radio upgrades and so on you have void your warranty). Of course if you can downgrade to your old rom nobody will notice that you did that.
But you have to be very careful on downgrading if you have also upgraded your radio I thinkk, cause you can brick your device (means having "NOGSM" after downgrading), see this note from mr. vanx downgrade guide for wm5:
NOTE: If your radio version is currently HIGHER than 1.27.00.00 then it is very likely the radio bootloader is version 0108, this WILL NOT allow the radio to be downgraded to a radio containing BL 0106 and will result in a "NO GSM" error.
Click to expand...
Click to collapse
Maybe you should follow mr. vanx downgrade guide for wm5 to make sure your on the safe side.
I thought he meant that it is still noticeable if you downgrade the IPL and SPL that it would be detected during warranty repairs but thats not the case...
I emailed I-Mate and they gave me an RMA# and had me purchase the $60.00 Diagnostic package from PocketPcTechs.com(They handle imate warranties in the US). So i did that, they emailed me with a form i should fill out and include it with my device when i ship it...
Did that, they sent me an email when they recieved my device, 15min after that i recieved another email that they were working on my devic, then Early the next day i get an email saying repairs are complete and its being ready to get shipped back to me... 15min an email with a tracking number saying its shipped....
Everything worked so smoothly, warranty was accepted, hopefully everything will be good when i get the device back (which should be today) I want to get rid of this ****ty iphone so bad!
todd_jg said:
Easiest thing to do is to download your original shipped ROM and extract the NBH file (using dutty's good nbh tool) and grab the IPL or SPL that you need and substitute that for the file from MrVanx. Just be careful what you flash - if you mix up the IPL and SPL file - InstaBrick! Trust me - I know
Click to expand...
Click to collapse
MrVanx instruction working just fine, however do not put your Hermes into Bootloader Mode. I've been trying the steps with my hermes in BootLoader Mode for many many times and it does not work. Leave it on OS mode. (Today) screen before you run the CustomRUU. Hope this help
why is every one so paranoid about this....
has anyone EVER heard of a warranty being denied because of the software on it?
GldRush98 said:
why is every one so paranoid about this....
has anyone EVER heard of a warranty being denied because of the software on it?
Click to expand...
Click to collapse
Yup cingular/ att will charge you for out of warranty work if its a different rom
Please help
Guys I am having the same issue, I am exchanging my phone and need to downgrade. I followed MrVanx guide and downgraded to 1.10.olipro and now need to flash the original Cingular 8525 SPL back to the phone. The SPL that was shipped was 1.11. Where can I find the file to flash? I have been trying to find it with no luck. Could someone please help me out with this? Thank you very much!
thedude0420 said:
Guys I am having the same issue, I am exchanging my phone and need to downgrade. I followed MrVanx guide and downgraded to 1.10.olipro and now need to flash the original Cingular 8525 SPL back to the phone. The SPL that was shipped was 1.11. Where can I find the file to flash? I have been trying to find it with no luck. Could someone please help me out with this? Thank you very much!
Click to expand...
Click to collapse
Go to the wiki > hermes > original shipped wm5 roms and then decompile the rom with duttys good nbh tool. You will see an spl.nb file. Make that alone into an nbh file using duttys good nbh tool. Then flash to your hermes using the custom ruu.
Since you have successfully followed mrv's guide, you should probably know what all those things are.
todd_jg said:
Go to the wiki > hermes > original shipped wm5 roms and then decompile the rom with duttys good nbh tool. You will see an spl.nb file. Make that alone into an nbh file using duttys good nbh tool. Then flash to your hermes using the custom ruu.
Since you have successfully followed mrv's guide, you should probably know what all those things are.
Click to expand...
Click to collapse
Man thank you so much for the fast reply! Having downgraded to 1.10.olipro and downloading the original rom exe, when I ran it (accidentally) it flashed the 1.11 SPL back to the phone for me. I didn't even have to use duttys tool. THANKS AGAIN!
thedude0420 said:
Man thank you so much for the fast reply! Having downgraded to 1.10.olipro and downloading the original rom exe, when I ran it (accidentally) it flashed the 1.11 SPL back to the phone for me. I didn't even have to use duttys tool. THANKS AGAIN!
Click to expand...
Click to collapse
No problem. I thought you already had the rom you wanted, but just needed to change the spl. Guess I gave the overly complex solution!
marcelser said:
Hi,
I have the following question. I currently have installed HardSPLv7 (so the device shows IPL-1.04 / SPL-2.20Olipro.
How exactly do I downgrade to my old IPL-1.00 / SPL-1.06 in case I have to hand-in my device for warranty reasons? I already searched through the forum and read that it can be done using sspl somehow but I couldn't find exact instructions.
Can anybody (maybe pof) give detailed instructions on how to downgrade to original ipl/spl from a .nbh with the correct ipl/spl files. I already prepared a .nbh with a spl-1.06 and the corresponding IPL extracted from an original vendor rom and put in my rebuilt dumped rom.
I also have the problem that I don't know where to get IPL-1.00, because on the page where to original roms are listed only the SPL version is noted, but not which ipl is in which rom. Can anybody tell me where I can get an IPL-1.00 .nb file?
Thanks for any help on this. I also think that maybe it could be interesting to put this onto the wiki if I anybody can answer this.
Thanks for any help.
Click to expand...
Click to collapse
Hey, maybe i come to late,
I had the same "problem", I had the Screen Aligment Issue. And I really wonderd myself if o2 have problem with my "Schaps ROM Version HardSPL" BUT there was no problem, they solved my Screen Aligment Issue. Afterwards I asked, what actually is bad for warrenty. Upgrading the Bootloader is no problem. But CID (Costumer ID) unlocking will may be evil. Anyway's for myself (the SA-Issue) was a hardware issue which has nothing todo with software facts like upgrading the bootloader...
dont be worried... i guess there will be no prob...
I'm trying to update my radio from 1.38.00.11 to 1.46.00.11. The update process works fine but in the info of my device the radio remains 1.38.00.11. What's wrong? thank you
xdaluke said:
I'm trying to update my radio from 1.38.00.11 to 1.46.00.11. The update process works fine but in the info of my device the radio remains 1.38.00.11. What's wrong? thank you
Click to expand...
Click to collapse
Hi,
have you installed a olipro 1.30 ?
If Yes you have do downgrade to version 1.20....
BYE, Bobo
Yes, I have olipro 1.3. If I downgrade it wiil be ok?
xdaluke said:
Yes, I have olipro 1.3. If I downgrade it wiil be ok?
Click to expand...
Click to collapse
Copy sspl_trin .exe made by Des in ur trinity. Go to explorer and launch it manually. Phone will go to bootloader mode. Then upgrade ur radio. In that way, u don't need to downgrade olipro hard spl.
i'm a little confused... is it better to downgrade to olipro 1.2 and if yes i have to do it in bootloader mode or just via activesync with device turned on?
xdaluke said:
i'm a little confused... is it better to downgrade to olipro 1.2 and if yes i have to do it in bootloader mode or just via activesync with device turned on?
Click to expand...
Click to collapse
In bootloader mode. No need to downgrade olipro. Just follow my instructions above. For anykind of rom update, you should be in bootloader mode.
Active sync is only to install softwares on your writable extra/storage memory and not the rom. In fact, rom is your operating system or read only memory.
...continued from: http://forum.xda-developers.com/showthread.php?t=472814
Official: RUU_Diamond_hTC_Asia_WWE_2.03.707.2_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship.exe
intertubes.info:
Clicky Clicky for intertubes.info mirror [450+ kb/s download speeds {i had it going at 470kb/s on a shared network}]
Rapidshare:
http://rapidshare.com/files/1857644...igned_Diamond_52.51.25.26_1.09.25.23_Ship.exe
HTC:
HTC Europe：
http://dl.htc.com/downloadfiles/Rom...igned_Diamond_52.51.25.26_1.09.25.23_Ship.exe
HTC USA：
http://member.america.htc.com/downl...igned_Diamond_52.51.25.26_1.09.25.23_Ship.exe
HTC Asia：
http://203.73.25.118/download/RomCo...igned_Diamond_52.51.25.26_1.09.25.23_Ship.exe
do any of these include copilot or tomtom?
edwardm said:
do any of these include copilot or tomtom?
Click to expand...
Click to collapse
They are the official HTC 2.03 ROMs, they are bland, boring and unmodified...so no, they don't contain copilot or TomTom.
Oh new official rom....
Yippeeee... waiting for new cooks
official rom flash
do we need a signed SPL to flash these ...?
bryangopan said:
do we need a signed SPL to flash these ...?
Click to expand...
Click to collapse
a newbie here also, same question, do we need a signed SPL to load this ROM from HTC?
thanks in advance.
jellyfish0000 said:
a newbie here also, same question, do we need a signed SPL to load this ROM from HTC?
thanks in advance.
Click to expand...
Click to collapse
More thank likely...HardSPL is your best bet, it almost guarentees a proper install of the rom.
lasterato said:
More thank likely...HardSPL is your best bet, it almost guarentees a proper install of the rom.
Click to expand...
Click to collapse
thanks. which version of SPL do you recommend or use?
jellyfish0000 said:
thanks. which version of SPL do you recommend or use?
Click to expand...
Click to collapse
developers edition 1.93 olinex
edwardm said:
developers edition 1.93 olinex
Click to expand...
Click to collapse
thank you for the information. btw, where can i get them? looks like i only found 1.40 from this tutorial http://forum.xda-developers.com/showthread.php?t=416211
Here you find 1.93Olinex
http://forum.xda-developers.com/showthread.php?t=400950
and in the same thread look at post #39 and download and read how to get the org. spl back for warranty..just a tip
omaga said:
Here you find 1.93Olinex
http://forum.xda-developers.com/showthread.php?t=400950
and in the same thread look at post #39 and download and read how to get the org. spl back for warranty..just a tip
Click to expand...
Click to collapse
thank you.
can't get it working on my HTC Diamond (Telstra). It came back with an error "Invalid Vendor ID".
jellyfish0000 said:
can't get it working on my HTC Diamond (Telstra). It came back with an error "Invalid Vendor ID".
Click to expand...
Click to collapse
Did you run the HardSPL? it's working on my telstra diamond fine
read the instructions properly in the link provided above
lasterato said:
Did you run the HardSPL? it's working on my telstra diamond fine
read the instructions properly in the link provided above
Click to expand...
Click to collapse
yes, installed the 1.93Olinex SPL.
jellyfish0000 said:
yes, installed the 1.93Olinex SPL.
Click to expand...
Click to collapse
You could try to flash from internal storage, read this to find out how :
http://forum.xda-developers.com/showpost.php?p=2707841&postcount=4035
lasterato said:
You could try to flash from internal storage, read this to find out how :
http://forum.xda-developers.com/showpost.php?p=2707841&postcount=4035
Click to expand...
Click to collapse
since i could not get this working, I have did the following:
loaded SPL-1.40.OliNex and loaded the following cooked ROM "Duttys_5.2.20764.1.4.3_V4_Full_MSVC_[2.03].zip" it works fine.
So i'm just wondering can i overwrite with this "hTC_Asia_WWE_2.03.707.2_Radio_Signed_D iamond_52.51.25.26_1.09.25.23" and use SPL-1.40.OliNex?
I also want to do the same. I just want to flash a latest HTC official ROM. The "cooked" ROMs are very confusing to me.
I have extracted the RUU_signed.nbh file. When I try to flash it with ROMUpdateUtility.exe (using SPL-1.40.OliNex), it actually shutdown the power of the phone and exit ActiveSync. I have to remove the phone battery to recover.
It also does not flash from the internal memory of the phone.
I also tried NBHUtil, still no good.
I have downloaded RUU_Signed_1_93OliNex_HSPL_UnsignedEdition.zip. When I try to flash it, it gives a version number 1.00. It is lower than my current number 1.40. So I did not try it.
I am running out of options. Any relevant suggestions would be appreciated.
jellyfish0000 said:
since i could not get this working, I have did the following:
loaded SPL-1.40.OliNex and loaded the following cooked ROM "Duttys_5.2.20764.1.4.3_V4_Full_MSVC_[2.03].zip" it works fine.
So i'm just wondering can i overwrite with this "hTC_Asia_WWE_2.03.707.2_Radio_Signed_D iamond_52.51.25.26_1.09.25.23" and use SPL-1.40.OliNex?
Click to expand...
Click to collapse
yangys said:
I also want to do the same. I just want to flash a latest HTC official ROM. The "cooked" ROMs are very confusing to me.
I have extracted the RUU_signed.nbh file. When I try to flash it with ROMUpdateUtility.exe (using SPL-1.40.OliNex), it actually shutdown the power of the phone and exit ActiveSync. I have to remove the phone battery to recover.
It also does not flash from the internal memory of the phone.
I also tried NBHUtil, still no good.
I have downloaded RUU_Signed_1_93OliNex_HSPL_UnsignedEdition.zip. When I try to flash it, it gives a version number 1.00. It is lower than my current number 1.40. So I did not try it.
I am running out of options. Any relevant suggestions would be appreciated.
Click to expand...
Click to collapse
whether it's cooked ROM or official ROM, it is recommended by the gurus here that you have Hard-SPL installed. After that, install cooked ROM or official ROM is the same method.
I have written a note about how to install the 2.03 official ROM on a DIAM130, as the following. I hope you'll find it useful if you have a Telstra branded Touch Diamond.
I'll never buy a carrier branded handset again as it makes ROM flashing more complicated.
Touch Diamond ROM flashing instructions
1. Hard-SPL
a. Download Unsigned-Hard-SPL-Diamond-OliNex.zip, and extract all files to a directory.
b. Establish a USB ActiveSync link
c. Double click ROMUpdateUtility.exe and follow on-screen instructions
2. HTC official ROM
a. Download RUU_Diamond_hTC_Asia_WWE_2.03.707.2_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship.exe, right-click it and extract all files to a directory.
b. Down-load NBHUtil.zip, double click it to start WinRAR (you may need to install WinRAR is you have not done so), double click NBHUtil.exe to start it.
c. Under Extract NBH, navigate to RUU_signed.nbh from step a, extract Radio, Splash, and OS. Note down the Target CID and version.
d. Under Build NBH, enter the Target CID and version as noted in the previous step. Build NBH and save it in the directory in step 1.
e. Connect USB and enter boot-loader – power up and hold-down the volume-down button
f. Double click ROMUpdateUtility.exe and follow on-screen instructions
g. After ROM update, it has only one band selection: UMTS (900+2100) + GSM (900+1800). This may not look good for Telstra. However, some people has commented that if select auto, 850MHz should be OK. With a number of testing with different mix of ROM and radio versions, it has been identified that this has nothing to do with radio drivers. This ROM has disabled other band selections.
3. Notes
a. ROM update when the phone is on may not be possible. The phone actually turns off. The phone battery must be removed to recover.
b. The ROM 2.03 update from the internal storage is not successful.
jellyfish0000 said:
whether it's cooked ROM or official ROM, it is recommended by the gurus here that you have Hard-SPL installed. After that, install cooked ROM or official ROM is the same method.
Click to expand...
Click to collapse
Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??