I'm trying to update my radio from 1.38.00.11 to 1.46.00.11. The update process works fine but in the info of my device the radio remains 1.38.00.11. What's wrong? thank you
xdaluke said:
I'm trying to update my radio from 1.38.00.11 to 1.46.00.11. The update process works fine but in the info of my device the radio remains 1.38.00.11. What's wrong? thank you
Click to expand...
Click to collapse
Hi,
have you installed a olipro 1.30 ?
If Yes you have do downgrade to version 1.20....
BYE, Bobo
Yes, I have olipro 1.3. If I downgrade it wiil be ok?
xdaluke said:
Yes, I have olipro 1.3. If I downgrade it wiil be ok?
Click to expand...
Click to collapse
Copy sspl_trin .exe made by Des in ur trinity. Go to explorer and launch it manually. Phone will go to bootloader mode. Then upgrade ur radio. In that way, u don't need to downgrade olipro hard spl.
i'm a little confused... is it better to downgrade to olipro 1.2 and if yes i have to do it in bootloader mode or just via activesync with device turned on?
xdaluke said:
i'm a little confused... is it better to downgrade to olipro 1.2 and if yes i have to do it in bootloader mode or just via activesync with device turned on?
Click to expand...
Click to collapse
In bootloader mode. No need to downgrade olipro. Just follow my instructions above. For anykind of rom update, you should be in bootloader mode.
Active sync is only to install softwares on your writable extra/storage memory and not the rom. In fact, rom is your operating system or read only memory.
Related
Hi, after speaking to Midget_1990, I have patched the RUU for the Universal to allow flashing with any CID on your phone, this is the official Universal RUU (with a slight GUI mod by someone Midget_1990 mentioned)
so have at it... enjoy.
thanks, was just about to upload it
thanks,
just downloaded and have a try
allway said:
thanks,
just downloaded and have a try
Click to expand...
Click to collapse
it does work... just has the minor caveat that it'll try to flash a Universal when it's not actually plugged in... so try not to be a complete plank with it.
Olipro said:
it does work... just has the minor caveat that it'll try to flash a Universal when it's not actually plugged in... so try not to be a complete plank with it.
Click to expand...
Click to collapse
i have flashed my universal with the new RUU.
It works fine.
Olipro
Is it possible that you will make a HardSPL for Universal?
We still have no way to recover bricked radio...
we were discussing that earlier. the nogsm shows when the radio bootloader is not written to the device properly for whatever reason. its still early days but it may be possible to create a new radio bootloader that cant be overwritten so that problem wont occur. however it wont fix thoses who allready ahve the problem.
Skwyk said:
Olipro
Is it possible that you will make a HardSPL for Universal?
We still have no way to recover bricked radio...
Click to expand...
Click to collapse
ok, if you are flashing a radio, and you brick your radio, but not the radio bootloader, then you should be able to recover by reflashing.
if you brick the Radio bootloader, then unfortunately, there is no way for you to recover from this; possibly the only way of recovery is directly accessing the radio chip pins via whatever interface it is... perhaps i2c? and flashing on a radio BL again through a separate interface... meaning you then need a radio bootloader binary in the correct format.
Olipro said:
ok, if you are flashing a radio, and you brick your radio, but not the radio bootloader, then you should be able to recover by reflashing.
Click to expand...
Click to collapse
Not in 100% of the cases... there are some situations where the radio bootloader is intact, but the radio is screwed, this causes all bootloader commands that require radio seclevel to be queried to hang the device (like 'task 32' or 'info 2'), thus not being able to flash it with the usual RUUs.
If this happens, it can easily be fixed with hermflasher by flashing the raw radio without prior authenticating to bootloader.
Olipro!!! am having No GSM here!!!
Dear Dr. PDAs
My Universal is suffering for bad blocks of Radio ROM i guess.
it Says NO GSM when boots.
Boots WIN CE very well
can't flash radio rom.
Please tell if we could have HardSPL for Universal or is there any other way to recover it...
waiting.
farehmani
hi everyone i m in need of new rom for my XDA Exec Universal plz help me as i m ver new.
V1640 and flash rom radio problem
hello,
On my V1640 my radio rom is version :0.00.00, and I can't flash it with a newradio rom. It is probably a CID Lock problem, How works Universal RUU ?
Is there a tutorial for flashing with Universal RUU ?
thanks
Regards
Has anyone got anywhere to fix problems with radio mess ups I have an O2 XDA Exec and loads 2.05 ok but error when flashing any Radio. Tried all I can find but no luck
simpleparab said:
hi everyone i m in need of new rom for my XDA Exec Universal plz help me as i m ver new.
Click to expand...
Click to collapse
Try to serch forum
Or, for lasy people try my folder blow
Flashing radio rom Ok !!!
I flashed the radio rom on another PC.... It works fine.
Try this..good luck
Flashing the O2 original ROm with this RUU
Hi,
Can i use this RUU combined with the original ROM from O2 to flash?
My current ROM:
ROM 1.13.82
Radio 1.04.02
ExtROM 1.13.188
New ROM available:
ROM 1.30.107
Radio 1.09.00
ExtROM 1.30.162
I have to use the bootloader mode to flash the new ROM because my XDA Exec has problem on connection with my PC via Active Sync. My Xda just dont sync with my PC where there is no connection established.
Hopefully someone can tell me what is this RUU? Whats the different than the original?
bejoa said:
Flashing radio rom Ok !!!
I flashed the radio rom on another PC.... It works fine.
Try this..good luck
Click to expand...
Click to collapse
this is the second time ppl have been able to flash no GSM Universals by using a nother PC. What was the spec of this pc and what was installed and Not installed in it.? I really want to unbrick my Universsal
I flashed my universal on a Laptop :
Gericom Select 2580+
AMD 2500+, 512 Mo ram, 80 Gb HD,
Windows XP Home SP2 pack
ActiveSync 4.2
Universal RUU
nothing special installed...
Good luck
bejoa,
what was the boot loader version of ur universal?
It is version 1.0
Hallo everbody.
I'd really be glad, if you could help my with my problem:
I currently have bepe's german WM6 ROM v. 0.5 installed on my P3600. Now, the problem is, that I cannot flash anything anymore. When I start any rom update, the device enters boot loader, the progress bar gradually counts to 100% (a little faster, than I remember it doing before). At 100% the device turns off, but doesn't reboot itself. The rom update utility reports a success. When I then restart the device, everything is as before, without any changes.
My installed Hard SPL is SPL-9.99.CP. I tried to flash Olipro's new SPL without any luck. The SPL remains SPL-9.99.CP.
I don't know what to do any more...
have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version
psxsnake said:
have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version
Click to expand...
Click to collapse
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.
paranoid2007 said:
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.
Click to expand...
Click to collapse
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.
nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.
Click to expand...
Click to collapse
Could you point me to SPL v. 1.2? I can't find it via the forum search.
nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe.
Click to expand...
Click to collapse
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?
sammy_deluxe said:
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?
Click to expand...
Click to collapse
No. If it might help, I'll try. Can you point me to where I can get an original german WM5 Rom?
Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!
paranoid2007 said:
Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!
Click to expand...
Click to collapse
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
sammy_deluxe said:
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
Click to expand...
Click to collapse
Doesn't work. Whenever I try to start Hard SPL, the bootloader shows up for about 5 seconds. Then the screen slowly starts fading to dark grey, so that I can't read anything on the display. Then nothing more happens.
try goin into the bootloader screen on the device first rather that using the update tool first.. this should work
steveecourt said:
try goin into the bootloader screen on the device first rather that using the update tool first.. this should work
Click to expand...
Click to collapse
OMG this worked! Thanks a million. Strangely enough, I tried it this morning without luck.
I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader
steveecourt said:
I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader
Click to expand...
Click to collapse
I have the same SPL but I had never flashed a rom from Flash card.. Could you explain more in the deep how it works? did it once with older Rom's?
Hi.
I already run the files ROMUpgradeUt.exe and at the end the UNI_Unlock_v1.exe. The Radio version 0.00.00. I get the new radio ROM and i want to know the procedures and what the software to use so i can send the radio rom to the PDA.
Thanks
Luís
http://vidmes.com/Uni/Radios/radio_1.18.rar
Putthe device in BL mode, and run MaUpgradeUt_noID
Laubscherc said:
http://vidmes.com/Uni/Radios/radio_1.18.rar
Putthe device in BL mode, and run MaUpgradeUt_noID
Click to expand...
Click to collapse
Thanks. It works
Luis
i'm trying to upgrade to VP3g's rom and every time i install the latest version of hard spl it says its not detectable or it says unknown version use safe spl. i follow the mrvanx guide everytime,...... whats wrong???????????????????
nothing, go ahead and continue. I'm sure everything will be fine. It's happened to me several times with different Roms but I had no problems flashing.
choose spl version, if hard spl v7 choose 2.10 then continue
kazuya_gonzalez said:
choose spl version, if hard spl v7 choose 2.10 then continue
Click to expand...
Click to collapse
i bricked my phone..............
edited , double post
Symbian_Black said:
i bricked my phone..............
Click to expand...
Click to collapse
are u sure have hard spl v 7? (2.10 olipro?)
i also have a problem that cannot detect my version..
but i choose version 2.10.. and it works for me for upgrade any rom..
I don't what you did but if you have HardSPL on your device then you haven't bricked it. Put it into Bootloader Mode (Tri color screen) and connect it to your computer. Get a Rom , try Schaps, and run the RUU Wrapper. If you have HardSPL on it then you should have no problems.
i have also this problem but i klick the version of my spl and it works
aint nffin wrong laddie
all will be fine
if it dont auto detect it will default to safe
but check the next screen to see if it reads correct
Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??