I have some problem to make new upgrade, my flash run for less 2 minute than restart with previeus rom.
now have bepe 0.79, I try with hard spl or SSPL-TRIN.exe, same problem
nothing happend
help me
resolved
are problem with sd card, removed and upgrade start normally
Related
I downloaded the Dopod 900 rom, wishing to change my PPC into Traditional Chinese. But after running the no id exe file. It reboot my PPC and said the country ID is not correct.
Afterwards I run the bootloader.exe on JASJAR. And it automactially go to bootloader mode. I'm able to upgrade my PPC rom. But after the cold reboot the system go to bootload mode (ask me to insert serial or USB cable). How can I get PPC work?
you always have to start your device in bootloader mode manually before upgrading.
as you didn't, special bit in the device was set, to start it always in bootloader mode now.
rerun the upgrade with MaUpgradeUtil_noid.exe again. it will fix it.
buzz
I got the same problem after upgrade to a new version complately but always still on bootloader mode,I have rerun the upgrade but still got same problem.Help please.
Reset while holding the power button
xdaIIse said:
I got the same problem after upgrade to a new version complately but always still on bootloader mode,I have rerun the upgrade but still got same problem.Help please.
Click to expand...
Click to collapse
Reflash the Jasjar again. But use the Radio Rom 1.04.02 only. Then do a reset.
Is here nobody who can read?!
Here is the answer how to solve the problem:
http://forum.xda-developers.com/viewtopic.php?t=33191
Or if you're unable to open the link:
make the update w i t h o u t any card (sd-card and sim-card) and you'll see: it works. Maybe you've to run the update twice without changing anything!
Teja
Hi,
I had a similar problem, system and unit both indicated a successful ROM flash but after the reset remained in bootloader mode ("Serial v1.00).
In the end I did a final JasJar ROM flash, then did the radio only ROM flash and after radio done, a reboot worked.
Maybe try the 1.04.02 radio only ROM flash and see if that works.
Note: during the last two ROM flashes I too had removed the SIM and SD cards.
Note: I had removed the SIM and SD cards for a number of ROM flashes prior to that, so I know how you feel finding out that wasn't the quick fix I read. But try all that in combination.
Regards
Michael
most of the time reviving a dead universal is easiest with another rom upgrade of the radio flash.
If your universal boots in usb mode (bootloader), I can confirm your universal is dead. Mostly caused by using an upgrade program that was not made for the universal. For instance using a cracked magician upgrade program to force universal upgrades. In most cases this will get you a dead universal which can easily be repaired by doing an aditional radio rom upgrade (even if you already have that radio upgrade)
Hi,
I can confirm that in the 2 instances of bricking my device (unable to get out of bootloader mode) that the radio only upgrade (1.04.02) got it working again.
I've done this for both the JasJar and Qtek ROMs (currently running Qtek).
My unit is a Dopod 900 originally purchased in Taiwan.
Regards
Michael
i had the same problem with the QTEK of my principal after I upgraded his ROMs.
(after the hard reset, the pocket remained in bootloader mode).
you can solve this problem in a very simple way:
you have to launch the bootloader installation (BL1.01_RUU_UNI_V.1.2.EXE) from the PC (still connected with the PPC through USB) while the PPC is in bootloader mode (on your display you see "USB > Serial 1.01" or something like that).
then you do a SOFT reset and the pocket boot normally.
very simple.
i hope to be helpful to someone.
Yep, i agree with u parallel666killer, it worked by just reinstalling the bootloader (BL1.01_RUU_UNI_V.1.2.EXE).
I've been using Mun_rus's WM6 ROM for quite a while and seeing that PDAVIET's rom was built on a more recent WM6 ROM I decided to flash PDAVIET 2.07.06.PV.
Since then I cannot flash anything on my Trinity, the update utility starts and when the progress bar reaches around 84% half the screen on the Trinity goes funny. The progress bar on the PC reaches the 100% (while the screen on the Trinity goes blank slowly slowly) but upon restarting the device PDAVIET ROM loads up again intact as if I have just done a soft reset!
I've even tried flashing WM5 again but without any success.
Trying to flash Hard-SPL does not work either and I'm running out of ideas now :-( Anyone else has this problem please? I would love to try flashing a ROM with an original IPL SPL but cannot find one. My bootloader currently says IPL 1.5/SPL 9.99.CP.
Yes I am having a similar problem. It starts to flash then stops reboots and on my pc says image fiile corrupted. I have re downloaded and extracted the files but it happens everytime. However. My trinity when it reboots is stuck in the splash screen.
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
i have the same problem...
i get 100% done and than it is still the old one..
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
deniser said:
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
Click to expand...
Click to collapse
I've run the splxploit a couple of times as well. It seems to finish the process succesfully but the problem persists :-( And mine is not stuck on splash screen, the device boots normally, it's just that whatever I flash does not work. Any more ideas please?
I tryed the all i think, read the all forum up and down, started in different ways, but no rom of SSL apply...
What is that!
I am stuck with this rom?
Any of the pro cookers can help with this please? I just need to understand what could be wrong, not necesseraly a solution
capeli said:
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
Click to expand...
Click to collapse
Hey many thanks Removing the miniSD solved my problem I flashed at least a 100 ROMS in my life and never bothered removing the memory card before ... but there you go
hi, i had the same problem. i flashed my trinity with original htc rom and after that when i tried to flash with any other rom it gave me success message after every try but in my phone there was still the same htc rom. i used that : http://forum.xda-developers.com/showthread.php?t=293632 AND IT WORKS. FROM THE MOMENT WHEN I USED THAT FILE I FLASHED MY TRINITY 2 TIMES WITH THE SAME ROMS WHICH DIDN`T WORKED PREVIOUS. you need to copy that file to your trinity and follow the instructions from the readme file. in my case i only opened it ,it started bootloader mode ,i disconected usb and connected it again and started ROMUpdateUtility with rom which i wanted.
interesting... so why does the miniSD card affect the flash?
kta- had you tried running sspl and then flashing during your failed attempts? (just curious)
well this is my last post for the night its 2:30 and I'm tired. I'll be checking up in the morning and maybe bumping my post for more answers.
while installing oprilo's hardsplv7 my computer froze and my phone was stuck on 47% I restart my computer and reset my phone only to find it stuck in the bootloader mode spl 2.03 from the official wm6 from cingular I had on my phone. so I reinstall the cingular 3.57 software onto my phone using the install wizard. it was the only way to unbrick it. when I went to try to download most roms I get the error [240] check update utility. reading the forum it says that code is given when you have a corrupt file.
Now you know my situation here is my question, How the h*** do I totally redo my phone back down to wm5 and spl 1.04 again? or is there another way to fix my semi bricked device? I've read the unbricking page and wasn't finding anything specific to my device.
Try using SD Card flashing
or
starting with phone in bootloader mode, then hook to PC, then start update and select the correct SPL version when prompted.
Crashing while flashing SPL can be a bad thing.
I was wondering about the SD way. its wierd I can flash using sspl with pandora kitchen and it uses the bootloader 1.09, but after its done flashing the new rom and go look at the bootloader screen again its back at 2.03.
I'll try the SD way if that doesn't work, I guess I'm stuck with the highest radio using install method from cingular. although I'd really like 1.50 radio. since I have gsm network over here
Yeah, you're playing with fire whenever you flash the radio. That's where unrecoverable bricking can occur, esp. if you don't have Hard-SPL installed.
Try another PC if you can't do SD flashing... sounds like flakey USB issues to me.
best to set your phone down and don't touch it or the cable until its finished.. also make sure you have a stable machine
Hi! I found this forum today, and decided to upgrade my X50v to WM6, from PPC2003SE. I got to the bootloader, and I successfully installed the WM5 bootloader. However, when the WM5 upgrade is done, the ppc won't turn on!! I have followed directions, and just after the upgrade is done and I get the message, i do a hard reset (reset + power), my x50v turns off and... stays off!!
What am I doing wrong???
Thanks for your help guys!!
I can still get to the bootloader...
Hello, I was in your boat an hour ago, so I'll try to help
you need to rename the "K" files with the prefix "DiMa" to "WM50" and that should make them show up in the sd loader. You will need some other SD card reader to do this of course.
they aren't showing up now because your new loader is now looking for the new prefix.
hi have you solved your problem? I have the same problem and my PDA is now laying on the table - not working of course can you help what to do and where can I find the bootloader and other software for that pda? thank you. Flea. please email me: fleateam(a)gmail.com
I can load the SD Image loader, and even run the new wm5 image from the SD card. Everything is done correctly, however when it comes to hard reset the axim, it just turns off and never restart. It is using now the new bootloader since the wm5 bootloader was upgraded successfully.
I'll give it a try by renaming the DiMa files.
After you flashed the boot loader is perfectly normal that your x50v won't turn on. If you correctly flashed the bootloader to the new WM5, your Axim cannot boot WM2003SE anymore. So you have to start bootloader again to upgrade the O.S. ROM section. After that you should have no problem...
hi all, my situation in this:
i ve an htc s300+ with hardspl 1.30 installed that in boot loader write "WLAN error" , when boot it is blocked to 2nd screen (HTC logo). i ve try with any solution on this forum.. with mtty not solution, with "splxploit" no solution.. i understand that the problem is when i try to flash a Rom radio it don't wont load over 7% and reboot in boot loader, or a original italian complete rom WM5 it don't wont load over 13% but not reboot.
if i flash only the ROM WM6 coocked it load full but the problem is the same.. (after reboot blocket to 2nd screen)..i ve try to flash also directly with mini SD but the loading stopped after start (about 13%)..
the situation is the same if i load with "splxploit" the hardspl 1.20, or sspl 1.05 or 1.06...
i try all solution in my mind... but no resolve this problem..
can anyone with more experience that me to help?
thanks
sorry but i am italian and my english is not good..
I think you have not complete reading all instruction before you start.
HARDSPL Olipro 1.30 is not able to flash Radio Rom as feedback by many.
You should use Olipro 1.20 or Des's SPL.
Sorry, I have the same problem,
How I can downgrade the H-SPL from 1.3 to 1.2 if the P3600 don't boot on, it is stop at startup logo HTC
Thx
Just put your device manualy in bootloader and flash again...It should work
IT don't work.
The process it is ok at 100%, but if I put the pda in bootloader I have again 1.30
Where I wrong?
Have you tried to flash from SD Card? Maybe this would work differently.
Try flashing HTC official rom
As stupid as it sound, it worked for me. it seems the official WM5 rom has some recovery features. It takes forever to flash (and obviously it does some different stuff than cooked roms) but it took my bricked trinity from its brick mode at least twice the past 3 years. If you can't get hold on one, although I am sure it is on this forum, PM me and I will upload it for you. Just too tiered to do so if you have another source to take it from.
Look for RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship. Be aware after it you may need to update the radio as well, but this is easy.
BigE
Please upload the file!!!!!!!!
Thx
for lazy ppl who do not search
http://rapidshare.com/files/47349234/latest_dopod_wm6_anznospl.rar.html
BigE
try this one
http://cid-8231c261cbdd4326.skydriv....751.5|_6275|_1.56.70.11|_108|_Ship.part1.rar