I'm not sure but I read through these threads:
http://forum.xda-developers.com/showthread.php?t=299950&highlight=voip
http://forum.xda-developers.com/showthread.php?t=303493&highlight=voip
Is there a seperate WM6 VOIP cab available somewhere? I don't see the suggested files, so I assume that I don't have it on my WWE WM6 rom.
Try search for VOIP...or look through todays postings for the same question:
and try these two posts
http://forum.xda-developers.com/show...highlight=voip
http://forum.xda-developers.com/show...highlight=voip
A quick search for VOIP will give you same answers
epmulligan said:
Try search for VOIP...or look through todays postings for the same question:
and try these two posts
http://forum.xda-developers.com/show...highlight=voip
http://forum.xda-developers.com/show...highlight=voip
A quick search for VOIP will give you same answers
Click to expand...
Click to collapse
Well, as you may have noticed I've found those threads, but I saw that the most of the thread is regarding HERMES.
I was wondering if anyone with an Artemis has been able to turn on VOIP (native voip)
I did manage to install the package as mentioned in the threads above, as well as put in the right config files. Also, the "Internet Calling: Available" today plugin is correctly displayed. However, I cannot switch dial pads and I don't get the correct status (connected).
Same problem here
Setup was done with Sip Config Tool 2.0.1
The plugin is configured : "Always, if available"
When connected by wlan or activesync the plugin displays : "Kein Empfang"
Disconnected from network displays : "Available"
Hopefully someone can help me
Guys I've got it working just fine on an xda orbit. There does seem to be a little bug though and that is when it's says "Searching" and "Available" on the today screen. Available actually means searching and searching means available
When searching is displayed, click on it in the today screen and you might notice a slight change in the signal which means it has switched to voip rather than gsm. Go to the phone screen and you'll see that the network has changed to your voip provider and any call you make will be routed through them.
I have downloaded sjphone yesterday and configured it to use my sip voip provider and it works brilliantly. The sound quality in sjphone is absolutely brilliant compared to the native voip, you should try it.
Finally it's working...
I tried to deinstall the plugin and after prompting an error it worked
The homescreen plug signals "searching" but as you said before it means "availabe". There are still a couple of things:
1) no incomming calls... i can't find the stun settings
2) +4930xxxxxx format doesn't work, i've to type 030xxxx
3) doesn't work after standby
Which version of sjphone are you using? There seems to be nothing available for wm 6
Hi BlueD,
I'm glad it's working for you. I tested incoming calls and that worked nicely as well without configuring any stun. The voip I used were sipgate and callcentric.
There's a post somewhere on one of the big voip threads and the guys managed to customize the dialing plans so that you can dial without using the international format. Do a quick search on voip dialing plan and you should find it somewhere.
Well obviously it doesn't cause the wifi disconnects, hence making it only useful for dialing out rather than receiving calls, except ofcourse if you want to leave the device on all the time, but that's not a very feasible solution.
The sjphone I downloaded was the one for v.1.60.303c Pocket PC 2003SE, it works nicely with excellent call quality. I also think you don't really need native voip capabilities to run that, which makes me think we could have had this on WM5 hmmm...
OK.. just fyi - i got a little bit more success in using the native VOIP solution. I had to flash from the WWE 6 to the BnB 2 ROM, then install the VOIP.cab and SipConfigTool. Now i can receive calls, but cannot place any... not sure why. Also, when i receive a call the sound is CRAP.. probably some codec issue here.
What type of internet connection have you?
Have you open ports on your router necessary for SIP, inbound and out?
epmulligan said:
What type of internet connection have you?
Have you open ports on your router necessary for SIP, inbound and out?
Click to expand...
Click to collapse
Yep I did. I got this confirmed by testing it with a softphone on my PC, which works great (same voip provider etc).
Related
May I know will VOIP worked with Hermes LVSW Edition (2007-03-26)?
I installed the VOIP.cab, and check with windows folder, there is No such files.
ipdialplan.xml
dnsapi.dll
voipphonecanvas.dll
rtcdll.dll
May I know How to make it work?
I'm not using LVSW edition but VOIP is working with my WM6. Try download this,
ftp://xda:[email protected]/Hermes/WMXL_Support_Files/WM6VoIP.CAB
May I know which version of WM6.0 you used?
Slightly modified Black v1.2.
I already make a few call just now. Works but there is echo.
May I know do u have these files?
ipdialplan.xml
dnsapi.dll
voipphonecanvas.dll
rtcdll.dll
Initially do not have. But after installing tha CAB I show you earlier, the files now in the windows directory.
Working VOIP on LVSW
I work with the LVSW 25-3-2007. VOIP works fine, but besides the VOIPWM6.cab, you also need to generate a voip.cab with your settings, like username and password.
Search the thread where everything has been bescribed. Follow the instructions and VOIP works... for me without echo (voipbuster).
I have create the VoIP.Cab and installed it, but the Internet Call alway available or no service, but I can't use it!
You have to tap the today item for internet call. until it become selected.
What provider that you use? I use voipstunt & voipbuster.
I using HKBN and I have tap the Internet Call, but there is No response!
In internet calling tab, what do you select? For me I select Use internet calling "whenever available"
Yes, I have select the Whenever available.
I 've a similar problem too.
I've installed the LVSW Edition, + the voip Cab.
I've configured a .cab to enter my ISP configuration.
When I launch Wifi, in 10-15 sec, I have : Internet Calling Available on the today screen.
BUT !
When I click on the internet tab on the today screen, I just see the configuration never, whenever available, only if cellular is not available.
And that's all !
How can I phone ?
When I use the green button of the hermes, I have "no sim card".
( I've removed it)
And I don't see how to pass a call.
Help is welcome.
Thanks to all !
Why you not try voipbuster or voipstunt.
How can I make the internet call from available to selected?
I have check the phone , which contain Prov0SIPSettings under the directory \Windows\System\VoIP
You may need some registry editing,
HKLM\System\VoIP\SIP\EnablePort5060
change to value from 0 to 1
If you connect to internet using 3G then
HKLM\Comm\RTC\AdapterTypes
delete value for both 1 & 2.
After that softreset your Hermes.
When internet call become selected, all your call will be using VoIP.
I did the registry changes, but, no way !
It always tell me that I can't launch the call !
Don't understand...
If someone could help !
I change these registry and reset, it still show available.
Does your configuration in voip is correct? ie username, password, server, port, etc..
If you are using voipstunt, I can show you my configuration.
The configuation may be correct,but some setting I need to confirm, Anyone know the sip.registrar.com of the HKBN 2b service? or the configuration of HKBN?
THIS IS THE SOLUTION FOR ME WITH YOUR ANSWERS
1) Create any VoIP Account with a provider (for example I use VoIPStunt)
2) Configure the wm6 voip with your settings account:
http://forum.xda-developers.com/showthread.php?t=299950
or more easy,
http://forum.xda-developers.com/showthread.php?t=303493
3) Talk using VoIP:
http://forum.xda-developers.com/showpost.php?p=1233797&postcount=14
4) Call to SIP address:
http://forum.xda-developers.com/showpost.php?p=1235084&postcount=21
and
http://forum.xda-developers.com/showpost.php?p=1234112&postcount=19
Thanks a lot for your help.
Toni
Hi all,
sorry if this post is OFFTopic for this forum, but I search and read other post and I not find the solution.
I want use the WM6 VoIP (with lVSW ROM). I install the voip cab and the settings for my provider.
The question is: how can I receive calls? how can I make calls? I not find any dialpad or similar to make it.
Thanks a lot and sorry for the offtopic.
Toni
Click to expand...
Click to collapse
I have been reading a little about this but have not done anything about it because been to busy flashing...lol...but anyhow if you already did everything i think i read that in order for it to work you need to be connected to WIFI, not your isp...if im wrong please correct me someone!! and if anyone got it to work with AT&T please post carrier settings please!
ToniSC said:
Hi all,
sorry if this post is OFFTopic for this forum, but I search and read other post and I not find the solution.
I want use the WM6 VoIP (with lVSW ROM). I install the voip cab and the settings for my provider.
The question is: how can I receive calls? how can I make calls? I not find any dialpad or similar to make it.
Thanks a lot and sorry for the offtopic.
Toni
Click to expand...
Click to collapse
If you searched in the forum you would have found this thread
http://forum.xda-developers.com/showthread.php?t=299950
Hi Shaun33
I found this post and I read all the commants. I make all steps that post indicated, but my problem is that I doesn't know how to use the wm6 voip.
In the same port, anybody has the same problem, but there hasn't answer.
Thanks.
Toni
if you can't see an answer in the thread (http://forum.xda-developers.com/showthread.php?t=299950) then there probably isn't an answer!
ToniSC said:
Hi Shaun33
I found this post and I read all the commants. I make all steps that post indicated, but my problem is that I doesn't know how to use the wm6 voip.
In the same port, anybody has the same problem, but there hasn't answer.
Thanks.
Toni
Click to expand...
Click to collapse
Why not you post what you have done & we identify what is the problem & give the solution.
i think he just wants to know how to actually use it
I am wondering, if he buy the VOIP service or not....
I wanna ask, will other VOIP service provider work on WM6?
like SunRocket or ViaTalk, etc.
TIA
ToniSC said:
Hi all,
sorry if this post is OFFTopic for this forum, but I search and read other post and I not find the solution.
I want use the WM6 VoIP (with lVSW ROM). I install the voip cab and the settings for my provider.
The question is: how can I receive calls? how can I make calls? I not find any dialpad or similar to make it.
Thanks a lot and sorry for the offtopic.
Toni
Click to expand...
Click to collapse
If I understand you correctly, you want to know how to make a call after getting your VOIP settings. Actually, there is no separate dial-pad for a VOIP call - you have to use the existing dial-pad which you would normally use when making a cellular call.
If you have set up your VOIP settings correctly, your plug in on your Today screen should say "your VOIP service:Available or Searching" instead of Internet Calling : Available/Not Available.
In my case, I use Gizmo, so it says Gizmo:Available (when it's not connected) and Gizmo:Searching (when connected via wifi).
When it says Searching, you click on the plug-in, then go to your normal dialing pad where it should also say "Gizmo" on the top right hand corner to indicate that WM6 is using VOIP instead of GSM to make the call.
Hope this helps.
As I am a noobie, I would appreciate it if the senior members could either confirm the above or correct anything which is wrong above.
arul said:
If I understand you correctly, you want to know how to make a call after getting your VOIP settings. Actually, there is not ..........
Click to expand...
Click to collapse
This is the correct "Usage Instructions" for voip.
This is also how I experienced it. Voip only connects through WIFI, although I have made the registry changes as mentioned in another thread. It will be nice if you can select which service to use eg. VOIP or GSM
what if i want not use voIP but my gsm network to call. there is isnt any option to do that once you setup voip. you can disable it but thats not the point. nokia's give you option. am i wrong?
nolovelust said:
what if i want not use voIP but my gsm network to call. there is isnt any option to do that once you setup voip. you can disable it but thats not the point. nokia's give you option. am i wrong?
Click to expand...
Click to collapse
Just tap the today screen item for it toggles between VoIP and GSM
ok... lots of speculation here. Let me tell you what I know:
VoIP, when properly installed, works in the following manner. (If you can't obtain these results then your ROM needs upgrading or your provisioning is incorrect).
Initially, the Internet Calling today screen plugin will show "off" when VoIP is set to "Never" in the Internet tab of phone settings.
When connected to WiFi, you can change this setting to "whenever available". At this point, a properly provisioned VoIP installation will show your VoIP provider from the provisioning XML and "Searching". Shortly after, "Searching" will change to "Selected". At this point all outbound calls placed from your phone will be through your VoIP provider. In fact, the phone skin will show this name too.
However, your phone will ring for incoming calls made to your GSM phone number as well as your VoIP phone number
Now, tapping "Selected" on the Today screen VoIP plugin will change this status to "Available".
At this point, outbound calls get placed through your GSM provider again and the phone skin will show your GSM provider name.
However, inbound calls to both your GSM and VoIP numbers will still ring on your phone.
Turn off VoIP again by going to phone settings and changing the calling network to Never.
Additional notes:
The "Searching" forever behavior previously described is a Bug in some WM6 releases. lvsw 4/23 doesn't have this issue.
You can also set VoIP to work over 3G as well as WiFi by removing the values "1" and "2" in HKLM\Comm\RTC\AdapterTypes. However, there are issues with this that haven't been fully resolved yet. Incoming calls work fine but the called party can't hear you when you place an outgoing VoIP call over 3G.
so there is no way to do this
dial a number select or even press voip button and you dial via voip.
i hate symbian but i might just have to carry to phones because voip enabled nokias can do it.
hmmm maybe you didn't understand. Sorry about that. Short answer is No, there is a way to do this. You can dial any way you want with VoIP active. Just toggle the today setting between "Selected" or "Active" to choose which to use.
Computer to computer calls
I was wondering if there could also be made computer-to-computer-calls. Is there a way to enter 'voip-names' instead of phone-numbers?
at&t CallVantage
How about those of us on Cingular or "The New at&t" is it possible to subscribe to the at&t VoIP service called CallVantage and then get it working on the Hermes?
@tembares:
You *could* try calling directly to the other phone's IP address. the default dialplan supports this. use the following syntax (example assumes you're calling a phone whose address is 192.168.0.1):
192*168*0*1
@brandyholt:
If the AT&T Callvantage service supports a SIP based softphone then the answer is yes.
Thanks a lot Sleuth255 and all people answer to me.
Finally I have been able to make work it!!!!!
@Sleuth255
One question please, if 192.168.0.1 is 192*168*0*1, how I dial for call to an SIP address, for example my gizmo address [email protected]
Toni
Sleuth255 said:
@tembares:
You *could* try calling directly to the other phone's IP address. the default dialplan supports this. use the following syntax (example assumes you're calling a phone whose address is 192.168.0.1):
192*168*0*1
@brandyholt:
If the AT&T Callvantage service supports a SIP based softphone then the answer is yes.
Click to expand...
Click to collapse
Hello,
I’ve read tons of tread in the forum regarding VoIP but I still can’t get my thick heard round it. I’m massively confused I definitely need help.
I’m wondering if there is any simplify tutorial in the forum of how to install VoIP, Sip, pleasessssssssssss?
I’m currently running Black 2.5 – Radio Version 1.41.00.10-Rom Version 3.29.707.4
Do you have a SIP based softphone account with a VoIP provider yet? Alternately, have you installed asterisk or 3CX server?
Also, VoIP isn't fully sorted on black 2.5 yet to my knowledge.
VoIP & Radio help.
Currently I do not have VoIP account with any providers, do I need one to get the settings to the phone, if yes which provider would you recommend pls?
Secondly I haven’t installed any of the software mentioned in your reply yet, I thought I’ll bump into step by step guide in the forum do that.
I think the last paragraph of your reply answers my frustration really,Its a matter of wait till VoIP settle on Black 2.5. keep me Fingers cross.
Hey! Least I forgot, how do I stream radio on my Hermes? I have no problem connecting to T-mobile GPRS, as well as my USB wifi router. But for some reason it will just not connect to no online radio station. Do I need to install something??? Leave it to the expects to help. Thx
SIP Config
New SIP Config 2.0 by shaun33
http://forum.xda-developers.com/showthread.php?t=303493
http://forum.xda-developers.com/show...9950:rolleyes:
Input your VOIP provider info
Any patches for 2.5 Black yet?
It searches, tries to connect, but I get the following SIP response (after using Sip Config 2.0.0)
Got SIP response 481 "Call Leg/Transaction Does Not Exist" back from 192.xxx.xxx.xxx
There are alot posts and threads about SIP calling with a trinity and none of the conclude, Is there anyone that works on fixing the issue with sip internet calling for trinity ?
I speak of the issue of not hearing the other recipient.
OR is anyone that has installed a rom with WM6 on a trinity and SIP works fine for him ?
firiel said:
There are alot posts and threads about SIP calling with a trinity and none of the conclude, Is there anyone that works on fixing the issue with sip internet calling for trinity ?
I speak of the issue of not hearing the other recipient.
OR is anyone that has installed a rom with WM6 on a trinity and SIP works fine for him ?
Click to expand...
Click to collapse
Well my friend I have had a similar problem, but when I replaced the dll file as it was mentioned on the specified thread....with Resco explorer (could not do it with the standard file explorer of windows...), it worked OK. Sometimes however you have to try a couple of times to get a clear line, but I think this is an issue of the traffic you have on your WiFi ( I only use it with WiFi..). Also the voice you listen back is a bit faint, but with the headset you get in the purchase box of the P3600, problem is solved. Follow the instructions as they say and you will be fine!
SIP works fine for me, except for the fact that there's just not enough bandwidth for clear ulaw, and we need g729 or gsm for any kind of viability...
I've noticed the in call volume is very faint as well to the point of being unusable...
Is there a registry hack we can apply to change this?
Using Mun.s TE. CHeers
The reason for this thread is to help people get Skype working to its fullest extent and resolve some of the issues. The ultimate objective is to allow those with Skype subscriptions to get unlimited anytime calling across North America if they pay the $2.95 / month for the Skype plan and have unlimited data...
Download Skype 3.0 for Windows Phones here:
http://www.skype.com/intl/en/download/skype/windowsmobile/
It installs fine and theoretically works great, however, there are a number of issues:
1. Skype automatically routes all audio to the speakerphone.
To route the audio to the earpieces, install audioRoute from Teksoft:
http://teksoftco.com/storage/download.php?product=audioroute_ppc
This product is discussed here:
http://forum.xda-developers.com/showthread.php?t=495166
It essentially installs an icon in your taskbar that loads when the phone starts up. Once you open Skype, you click the icon, select the first icon, which is the earpiece, and then all audio will get routed to the earpiece when using Skype.
To route the audio to a Bluetooth headset, then install A2DP toggle from Teksoft:
http://teksoftco.com/storage/download.php?product=a2dptoggle
This program should theoretically allow you to select the Bluetooth headset when Skype is loaded. It should theoretically be able to be loaded concurrently with audioRoute. I have not tested it fully.
2. Skype will not work unless connected to a wifi connection
I had tested Skype and thought it worked flawlessly until someone with an iPhone mentioned that he had to install some sort of program to "trick" Skype into thinking it was connected to a Wifi. I believe that this is an issue with the way Microsoft has designed Windows Mobile, but is probably intential to prevent competition for telecommunication company voice packages. This issue supposedly does not exist with Windows Mobile clients.
Just ensure that ActivSync/Wifi/Mobile is enabled under the Connection settings.
3. Skype Mobile does not support video calling
I'm not sure if this is a software issue or just something that can be hacked. I see no reason why this functionality would be disabled in the Mobile version of Skype... any insight would be appreciated.
Would love it if anyone else is experiencing problem 2 as well... I want to find out if it's isolated to my handset... or even to just my carrier.
slaman said:
Would love it if anyone else is experiencing problem 2 as well... I want to find out if it's isolated to my handset... or even to just my carrier.
Click to expand...
Click to collapse
No problem here on a Vodafone TP2. Skype uses the 3G connection fine.
You know that htere's a setting that tells Skype what connection(s) to use? It defaults to "Use ActiveSync/Wifi" but can be changed to "Use ActiveSync/Wifi/Mobile"
It was working for me I think
see the message below
It was working for me I think
Maybe I'm misunderstanding the question, but I have made calls through Skype on my TyTN II using the Australian Three 3G network. Called my wife on her mobile in Shanghai with no problems. Well, the connection was pretty horrible (I think it's a bit hard work for both the phone and the network) but it connected fine for as long as I wanted.
As tjobbins said, in the Connection Method settings, I can "Use ActiveSync/WiFi" or "Use ActiveSync/WiFi/Mobile"... so if I'm overseas, I leave it on the first one; in Australia on the second one.
skippinshanghai said:
Maybe I'm misunderstanding the question, but I have made calls through Skype on my TyTN II using the Australian Three 3G network. Called my wife on her mobile in Shanghai with no problems. Well, the connection was pretty horrible (I think it's a bit hard work for both the phone and the network) but it connected fine for as long as I wanted.
As tjobbins said, in the Connection Method settings, I can "Use ActiveSync/WiFi" or "Use ActiveSync/WiFi/Mobile"... so if I'm overseas, I leave it on the first one; in Australia on the second one.
Click to expand...
Click to collapse
Interesting... I think my settings might have changed because I tested it again just now and it worked!
Thanks all!
I'm interested in how this works. I own the Titan at the moment and Skype only works over Wifi. Do you know if Skype plans on fixing the problem with calls only being heard from speaker phone? Any update on video calling?
off-topic question here, does anyone know if the titan operates on 3G? (i have sprint)
jtadeo said:
I'm interested in how this works. I own the Titan at the moment and Skype only works over Wifi. Do you know if Skype plans on fixing the problem with calls only being heard from speaker phone? Any update on video calling?
Click to expand...
Click to collapse
We can only hope. Skype have their forums and I saw a number of posts complaining about those missing features. I guess we should add our voices, though I would expect it will take a while for it to be fixed; the current version for Windows Mobile, Skype 3, was released fairly recently.
One alternative to look at is Fring. It supports better audio routing, i.e. calls are not only on speakerphone - they can come through the normal phone earpiece, or a bluetooth headset. Don't think it does video. As well as Skype, it also supports MSN, ICQ, Yahoo, AIM and others, so it's a good all-in-one client.
However on the TP2 Fring does currently have one quite annoying issue - it doesn't seem to work on Wifi. It's fine on mobile/3G connections, but on Wifi it won't list access points or connect. This is reported on their forums but no sign of a fix yet. Actually I did once get it connect to WiFi, but I don't really know how and haven't been able to repeat it.
Oh I just remembered the other huge problem with Skype for Windows Mobile - it doesn't list your phone contacts!
Bloody useless when you want to make a Skype Out call, and you end up having to go into the contact record, copy their number, and then paste it into Skype. Really daft.
Fring does list your contacts, and you can use it for Skype Out as well as Fring's own paid-for outbound dialling system.
I have another problem: NO notifications! So i don't know if someone chats or phone me! It's useless in that way!
tjobbins said:
Oh I just remembered the other huge problem with Skype for Windows Mobile - it doesn't list your phone contacts!
Bloody useless when you want to make a Skype Out call, and you end up having to go into the contact record, copy their number, and then paste it into Skype. Really daft.
Fring does list your contacts, and you can use it for Skype Out as well as Fring's own paid-for outbound dialling system.
Click to expand...
Click to collapse
Thanks for the suggestion. I want to make sure that I'm using only data-only when making calls, since I have unlimited data... and limited daytime voice minutes.
I installed fring, and it doesn't show the TP2 as a supported device. When I launched it, it kept asking me to find a WLAN... except nothing shows up on the list! Wifi is enabled AND data is enabled, and it keeps showing Not Available...
Has it worked on your TP2?
slaman said:
I installed fring, and it doesn't show the TP2 as a supported device. When I launched it, it kept asking me to find a WLAN... except nothing shows up on the list! Wifi is enabled AND data is enabled, and it keeps showing Not Available...
Has it worked on your TP2?
Click to expand...
Click to collapse
Nope. See my post before the one you quoted! It doesn't work on WiFi on the TP2 at the moment - and also on some other WM devices I think.
Works great on 3G and ActiveSync, just doesn't work on WiFi.
Except.. once for me it did. It suddenly connected and I don't know how or why. Haven't managed to repeat it yet though. But maybe there's a workaround lying in there waiting to be (re) discovered
tjobbins said:
Nope. See my post before the one you quoted! It doesn't work on WiFi on the TP2 at the moment - and also on some other WM devices I think.
Works great on 3G and ActiveSync, just doesn't work on WiFi.
Except.. once for me it did. It suddenly connected and I don't know how or why. Haven't managed to repeat it yet though. But maybe there's a workaround lying in there waiting to be (re) discovered
Click to expand...
Click to collapse
No no - I had wifi disabled and just tried to use regular data connection... but it couldn't find the connection for some reason.
Hate to bump an old thread... but I finally got Fring working on my TP2 (latest version), but SkypeOut calls don't actually direct to the Earpiece... I don't hear anything. Loudspeaker works fine.